The existing literature focuses on the applications of fast filter bank due to its excellent frequency responses with low complexity. However, the topic is not addressed related to the general transfer function expressions of the corresponding subfilters for a specific channel. To do this, in this paper, general closed-form transfer function expressions for fast filter bank are derived. Firstly, the cascaded structure of fast filter bank is modelled by a binary tree, with which the index of the subfilter at each stage within the channel can be determined. Then the transfer functions for the two outputs of a subfilter are expressed in a unified form. Finally, the general closed-form transfer functions for the channel and its corresponding subfilters are obtained by variables replacement if the prototype lowpass filters for the stages are given. Analytical results and simulations verify the general expressions. With such closed-form expressions lend themselves easily to analysis and direct computation of the transfer functions and the frequency responses without the structure graph.

The performance of a fully wireless-power-transfer (WPT) node network, in which each node transfers (and receives) energy through a wireless channel when it has sufficient (and insufficient) energy in its battery, was theoretically analyzed. The lost job ratio (LJR), namely, is the ratio of (i) the amount of jobs that cannot be done due to battery of a node running out to (ii) the amount of jobs that should be done, is used as a performance metric. It describes the effect of the battery of each node running out and how much additional energy is needed. Although it is known that WPT can reduce the probability of the battery running out among a few nodes within a small area, the performance of a fully WPT network has not been clarified. By using stochastic geometry and first-passage-time analysis for a diffusion process, the expected LJR was theoretically derived. Numerical examples demonstrate that the key parameters determining the performance of the network are node density, threshold switching of statuses between “transferring energy” and “receiving energy,” and the parameters of power conversion. They also demonstrate the followings: (1) The mean energy stored in the node battery decreases in the networks because of the loss caused by WPT, and a fully WPT network cannot decrease the probability of the battery running out under the current WPT efficiency. (2) When the saturation value of power conversion increases, a fully WPT network can decrease the probability of the battery running out although the mean energy stored in the node battery still decreases in the networks. This result is explained by the fact that the variance of stored energy in each node battery becomes smaller due to transfer of energy from nodes of sufficient energy to nodes of insufficient energy.

In this study, aiming at clarifying the characteristics of air-to-ground radio wave propagation in mountainous areas, a transmission experiment was performed between a drone equipped with a transmitter and three receivers set up on the ground using a 920MHz band wireless system at Uchigatani forest, which is located in Yamato-cho, Gujo-shi, Gifu Prefecture. In the experiment, we simultaneously measured the received signal strength indicator (RSSI) and the drone's latitude, longitude, and height from the ground. Then, we verified whether the measured data has the line-of-sight between the transmitter and receivers using a geographic information system and analyzed characteristics of the RSSI, packet loss rate, and fading concerning the height from the ground and distance between the transmitter and receivers. The results showed that increasing the drone's altitude to 90m or more makes the link more stable and that the fading distribution in mountainous terrains is different from in other terrains.

Today's electronic devices must meet many requirements, such as those related to performance, limits to the radiated electromagnetic field, size, etc. For such a design, the requirement is to have a solution that simultaneously meets multiple objectives that sometimes include conflicting requirements. In addition, it is also necessary to consider uncertain parameters. This paper proposes a new combination of statistical analysis using the Polynomial Chaos (PC) method for dealing with the random and multi-objective satisfactory design using the Preference Set-based Design (PSD) method. The application in this paper is an Electromagnetic Interference (EMI) filter for a practical case, which includes plural element parameters and uncertain parameters, which are resistors at the source and load, and the performances of the attenuation characteristics. The PC method generates simulation data with high enough accuracy and good computational efficiency, and these data are used as initial data for the meta-modeling of the PSD method. The design parameters of the EMI filter, which satisfy required performances, are obtained in a range by the PSD method. The authors demonstrate the validity of the proposed method. The results show that applying a multi-objective design method using PSD with a statistical method using PC to handle the uncertain problem can be applied to electromagnetic designs to reduce the time and cost of product development.

Non-orthogonal multiple access (NOMA), which combines multiple user signals and transmits the combined signal over one channel, can achieve high spectral efficiency for mobile communications. However, combining the multiple signals can lead to degradation of bit error rates (BERs) of NOMA under severe channel conditions. In order to improve the BER performance of NOMA, this paper proposes a new NOMA scheme based on orthogonal space-time block codes (OSTBCs). The proposed scheme transmits several multiplexed signals over their respective orthogonal time-frequency channels, and can gain diversity effects due to the orthogonality of OSTBC. Furthermore, the new scheme can detect the user signals using low-complexity linear detection in contrast with the conventional NOMA. The paper focuses on the Alamouti code, which can be considered the simplest OSTBC, and theoretically analyzes the performance of the linear detection. Computer simulations under the condition of the same bit rate per channel show that the Alamouti code based scheme using two channels is superior to the conventional NOMA using one channel in terms of BER performance. As shown by both the theoretical and simulation analyses, the linear detection for the proposed scheme can maintain the same BER performance as that of the maximum likelihood detection, when the two channels have the same frequency response and do not bring about any diversity effects, which can be regarded as the worst case.

This paper presents a high-NIR sensitivity SOI-gate lock-in pixel with improved modulation contrast. The proposed pixel has a shallow buried channel and intermediate gates to create both a high lateral electric field and a potential barrier to parasitic light sensitivity. Device simulation results showed that parasitic light sensitivity reduced from 13.7% to 0.13% compared to the previous structure.

Energy harvesting has been widely investigated as a potential solution to supply power for Internet of Things (IoT) devices. Computing devices must operate intermittently rather than continuously, because harvested energy is unstable and some of IoT applications can be periodic. Therefore, processors for IoT devices with intermittent operation must feature a hibernation mode with zero-standby-power in addition to energy-efficient normal mode. In this paper, we describe the layout design and measurement results of a nonvolatile standard cell memory (NV-SCM) and nonvolatile flip-flops (NV-FF) with a nonvolatile memory using Fishbone-in-Cage Capacitor (FiCC) suitable for IoT processors with intermittent operations. They can be fabricated in any conventional CMOS process without any additional mask. NV-SCM and NV-FF are fabricated in a 180nm CMOS process technology. The area overhead by nonvolatility of a bit cell are 74% in NV-SCM and 29% in NV-FF, respectively. We confirmed full functionality of the NV-SCM and NV-FF. The nonvolatile system using proposed NV-SCM and NV-FF can reduce the energy consumption by 24.3% compared to the volatile system when hibernation/normal operation time ratio is 500 as shown in the simulation.

In this research, we investigated the threshold voltage (VTH) control by partial polarization of metal-ferroelectric-semiconductor field-effect transistors (MFSFETs) with 5 nm-thick nondoped HfO2 gate insulator utilizing Kr-plasma sputtering for Pt gate electrode deposition. The remnant polarization (2Pr) of 7.2 μC/cm2 was realized by Kr-plasma sputtering for Pt gate electrode deposition. The memory window (MW) of 0.58 V was realized by the pulse amplitude and width of -5/5 V, 100 ms. Furthermore, the VTH of MFSFET was controllable by program/erase (P/E) input pulse even with the pulse width below 100 ns which may be caused by the reduction of leakage current with decreasing plasma damage.

This paper provides a new method to implement substrate integrated defected ground structure (SIDGS)-based bandpass filter (BPF) with adjustable frequency and controllable bandwidth. Compared with previous literature, this method implements a new SIDGS-like resonator capable of tunable frequency in the same plane as the slotted line using a varactor diode, increasing the design flexibility. In addition, the method solves the problem that the tunable BPF constituted by the SIDGS resonator cannot control the bandwidth by introducing a T-shaped non-resonant unit. The theoretical design method and the structural design are shown. Moreover, the configured structure is fabricated and measured to show the validity of the design method in this paper.

Due to the global outbreak of coronaviruses, people are increasingly wearing masks even when photographed. As a result, photos uploaded to web pages and social networking services with the lower half of the face hidden are less likely to convey the attractiveness of the photographed persons. In this study, we propose a method to complete facial mask regions using StyleGAN2, a type of Generative Adversarial Networks (GAN). In the proposed method, a reference image of the same person without a mask is prepared separately from a target image of the person wearing a mask. After the mask region in the target image is temporarily inpainted, the face orientation and contour of the person in the reference image are changed to match those of the target image using StyleGAN2. The changed image is then composited into the mask region while correcting the color tone to produce a mask-free image while preserving the person's features.

Various haze removal methods based on the atmospheric scattering model have been presented in recent years. Most methods have targeted strong haze images where light is scattered equally in all color channels. This paper presents a haze removal method using near-infrared (NIR) images for relatively weak haze images. In order to recover the lost edges, the presented method first extracts edges from an appropriately weighted NIR image and fuses it with the color image. By introducing a wavelength-dependent scattering model, our method then estimates the transmission map for each color channel and recovers the color more naturally from the edge-recovered image. Finally, the edge-recovered and the color-recovered images are blended. In this blending process, the regions with high lightness, such as sky and clouds, where unnatural color shifts are likely to occur, are effectively estimated, and the optimal weighting map is obtained. Our qualitative and quantitative evaluations using 59 pairs of color and NIR images demonstrated that our method can recover edges and colors more naturally in weak haze images than conventional methods.

A feedback node set (FNS) of a graph is a subset of the nodes of the graph whose deletion makes the residual graph acyclic. By finding an FNS in an interconnection network, we can set a check point at each node in it to avoid a livelock configuration. Hence, to find an FNS is a critical issue to enhance the dependability of a parallel computing system. In this paper, we propose a method to find FNS's in n-pancake graphs and n-burnt pancake graphs. By analyzing the types of cycles proposed in our method, we also give the number of the nodes in the FNS in an n-pancake graph, (n-2.875)(n-1)!+1.5(n-3)!, and that in an n-burnt pancake graph, 2n-1(n-1)!(n-3.5).

High power dissipation during scan test often causes undue yield loss, especially for low-power circuits. One major reason is that the resulting IR-drop in shift mode may corrupt test data. A common approach to solving this problem is partial-shift, in which multiple scan chains are formed and only one group of scan chains is shifted at a time. However, existing partial-shift based methods suffer from two major problems: (1) their IR-drop estimation is not accurate enough or computationally too expensive to be done for each shift cycle; (2) partial-shift is hence applied to all shift cycles, resulting in long test time. This paper addresses these two problems with a novel IR-drop-aware scan shift method, featuring: (1) Cycle-based IR-Drop Estimation (CIDE) supported by a GPU-accelerated dynamic power simulator to quickly find potential shift cycles with excessive peak IR-drop; (2) a scan shift scheduling method that generates a scan chain grouping targeted for each considered shift cycle to reduce the impact on test time. Experiments on ITC'99 benchmark circuits show that: (1) the CIDE is computationally feasible; (2) the proposed scan shift schedule can achieve a global peak IR-drop reduction of up to 47%. Its scheduling efficiency is 58.4% higher than that of an existing typical method on average, which means our method has less test time.

The bin packing problem is a problem of finding an assignment of a sequence of items to a minimum number of bins, each of capacity one. An online algorithm for the bin packing problem is an algorithm that irrevocably assigns each item one by one from the head of the sequence. Gutin, Jensen, and Yeo (2006) considered a version in which all items are only of two different sizes and the online algorithm knows the two possible sizes in advance, and gave an optimal online algorithm for the case when the larger size exceeds 1/2. In this paper we provide an optimal online algorithm for some of the cases when the larger size is at most 1/2, on the basis of a framework that facilitates the design and analysis of algorithms.

Packet classification is used to determine the behavior of incoming packets in network devices according to defined rules. As it is achieved using a linear search on a classification rule list, a large number of rules will lead to longer communication latency. To solve this, the problem of finding the order of rules minimizing the latency has been studied. Misherghi et al. and Harada et al. have proposed a problem that relaxes to policy-based constraints. In this paper, we show that the Relaxed Optimal Rule Ordering (RORO) for the allowlist is NP-hard, and by reducing from this we show that RORO for the general rule list is NP-hard. We also propose a heuristic algorithm based on the greedy method for an allowlist. Furthermore, we demonstrate the effectiveness of our method using ClassBench, which is a benchmark for packet classification algorithms.

This letter is devoted to constructing new Type-II Z-complementary pairs (ZCPs). A ZCP of length N with ZCZ width Z is referred to in short by the designation (N, Z)-ZCP. Inspired by existing works of ZCPs, systematic constructions of (2N+3, N+2)-ZCPs and (4N+4, 7/2N+4)-ZCPs are proposed by appropriately inserting elements into concatenated GCPs. The odd-length binary Z-complementary pairs (OB-ZCPs) are Z-optimal. Furthermore, the proposed construction can generate even-length binary Z-complementary pairs (EB-ZCPs) with ZCZ ratio (i.e. ZCZ width over the sequence length) of 7/8. It turns out that the PMEPR of resultant EB-ZCPs are upper bounded by 4.

This paper proposes two full-digital receive beamforming (BF) methods for low-complexity and high-accuracy uplink signal detection via Gaussian belief propagation (GaBP) at base stations (BSs) adopting massive multi-input multi-output (MIMO) for open radio access network (O-RAN). In addition, beyond fifth generation mobile communication (beyond 5G) systems will increase uplink capacity. In the scenarios such as O-RAN and beyond 5G, it is vital to reduce the cost of the BSs by limiting the bandwidth of fronthaul (FH) links, and the dimensionality reduction of the received signal based on the receive BF at a radio unit is a well-known strategy to reduce the amount of data transported via the FH links. In this paper, we clarify appropriate criteria for designing a BF weight considering the subsequent GaBP signal detection with the proposed methods: singular-value-decomposition-based BF and QR-decomposition-based BF with the aid of discrete-Fourier-transformation-based spreading. Both methods achieve the dimensionality reduction without compromising the desired signal power by taking advantage of a null space of channels. The proposed receive BF methods reduce correlations between the received signals in the BF domain, which improves the robustness of GaBP against spatial correlation among fading coefficients. Simulation results assuming realistic BS and user equipment arrangement show that the proposed methods improve detection capability while significantly reducing the computational cost.

A 2-D beam scanning array antenna fed by a compact 16-way 2-D beamforming network (BFN) designed in Broadside Coupled Stripline (BCS) is addressed. The proposed 16-way 2-D BFN is formed by interconnecting two groups of 4x4 Butler Matrix (BM). Each group is composed of four compact 4x4 BMs. The critical point of the design is to propose a simple and compact 4x4 BM without crossover in BCS to achieve a better transmission coefficient of the 16-way 2-D BFN with reduced size of merely 0.8λ0×0.8λ0×0.04λ0. Moreover, the complexity of the interface connection between the 2-D BFN and the 4x4 patch array antenna is reduced by using probe feeding. The 16-way 2-D BFN is able to produce the phase shift of ±45°, and ±135° in x- and y- directions. The 2-D BFN is easily integrated under the 4x4 patch array to form a 2-D phased array capable of switching 16 beams in both elevation and azimuth directions. The area of the proposed 2-D beam scanning array antenna module has been significantly reduced to 2λ0×2λ0×0.04λ0. A prototype operating in the frequency range of 4-6GHz is fabricated and measured to validate the concept. The measurement results agree well with the simulations.

This paper investigates a service deployment model for network function virtualization which handles per-flow priority to minimize the deployment cost. Service providers need to implement network services each of which consists of one or more virtual network functions (VNFs) with satisfying requirements of service delays. In our previous work, we studied the service deployment model with per-host priority; flows belonging to the same service, for the same VNF, and handled on the same host have the same priority. We formulated the model as an optimization problem, and developed a heuristic algorithm named FlexSize to solve it in practical time. In this paper, we address per-flow priority, in which flows of the same service, VNF, and host have different priorities. In addition, we expand FlexSize to handle per-flow priority. We evaluate per-flow and per-host priorities, and the numerical results show that per-flow priority reduces deployment cost compared with per-host priority.

A fully analog pipelined deep neural network (DNN) accelerator is proposed, which is constructed by using pipeline registers based on master-slave switched capacitors. The idea of the master-slave switched capacitors is an analog equivalent of the delayed flip-flop (D-FF) which has been used as a digital pipeline register. To estimate the performance of the pipeline register, it is applied to a conventional DNN which performs non-pipeline operation. Compared with the conventional DNN, the cycle time is reduced by 61.5% and data rate is increased by 160%. The accuracy reaches 99.6% in MNIST classification test. The energy consumption per classification is reduced by 88.2% to 0.128µJ, achieving an energy efficiency of 1.05TOPS/W and a throughput of 0.538TOPS in 180nm technology node.