Yasuhiro NAKASHA Naoki HARA Kiyomichi ARAKI
This paper presents the analytical results of the effects of jitter and intersymbol interference (ISI) on a millimeter-wave impulse radio (IR) transceiver, compared with the performance of a developed 10-Gb/s W-band IR-transmitter prototype. The IR transmitter, which is compact and cost-effective, consists of a pulse generator (PG) that creates an extremely short pulse, a band-pass filter (BPF) that shapes the short pulse to the desired millimeter-wave pulse (wavelet), and an optional power amplifier. The jitters of the PG and ISI from the BPF are a hindrance in making the IR transceiver robust and in obtaining excellent performance. One analysis verified that, because of a novel retiming architecture, the random jitter and the data-dependent jitter from the PG give only a small penalty of < 0.5-dB increase in the signal-to-noise ratio (SNR) for achieving a bit error rate (BER) of < 10-12. An alternative analysis on the effect of ISI from the BPF indicated that using a Gaussian BPF enables a transmission with a BER of < 10-12 up to a data rate of 1.4 times as large as the bandwidth of the BPF, which is twice as high as that of a conventional amplitude shift keying (ASK) system. The analysis also showed that the IR system is more sensitive to the ISI than the ASK system and suggested that the mismatching of the skirt characteristics of the developed BPF with those of a Gaussian BPF causes tail lobes following the wavelet, resulting in an on/off ratio of 15 dB and hence, an SNR penalty of 6 dB.
This paper presents pulse-coupled piecewise constant spiking oscillators (PWCSOs) consisting of two PWCSOs and a coupling method is master-slave coupling. The slave PWCSO exhibits chaos because of chaotic response of the master one. However, if the parameter varies, the slave PWCSO can exhibit the phenomena as a periodicity in the phase plane. We focus on such phenomena and corresponding bifurcation. Using the 2-D return map, we clarify its mechanism.
Shuhei FUJITA Takuya SAKAMOTO Toru SATO
UWB (Ultra Wide-Band) pulse radar is promising for surveillance systems because it has an outstanding high range-resolution. To realize an accurate UWB radar imaging system, we propose a new approach that employs multipath echoes from a target in an indoor environment. Using multipath echoes, the proposed system can accurately estimate images, even for targets in a shadow region where the targets are out of sight of the antenna. We apply a simple interferometry technique using the multiple mirror image antennas generated by multipath propagation. We find that this simple method also produces many undesired false image points. To tackle this issue, we also propose an effective false image reduction algorithm to obtain a clear image. Numerical simulations verify that most of the false image points are removed and the target shape is accurately estimated.
Shey-Shi LU Hsiao-Chin CHEN Shih-An YU
The effective ISFs of differential LC oscillators are derived under the assumption that the drain-to-source current is linearly dependent on the gate-to-source voltage for transistors operated in saturation. Moreover, a new interpretation of phase noise is given by examining the real vector diagram of the carrier signal, upon which the noise voltage induced by the impulse noise current is superimposed. The distinct feature of our vector diagram lies in that the noise voltage is always parallel with the horizontal axis. From the Fourier transformations of the derived effective ISFs, the phase noise of differential LC oscillators can be formulated with physical meanings in the frequency domain. The proposed theory can well describe the translation of the noise spectra when the noises from the LC-tank, the switching transistors, and the tail current source are converted into the phase noise. Theoretical predictions from our formulas agree well with the simulation results.
Masahiro OHISHI Fumio OHTOMO Masaaki YABE Mitsuru KANOKOGI Takaaki SAITO Yasuaki SUZUKI Chikao NAGASAWA
A new speed enhancement technique for pulsed laser rangefinders based on Lagrange's theorem in group theory using an undersampling method has been developed. In the undersampling method, frequency conversion for high-resolution ranging and digitizing are conducted by sampling a reference frequency signal at the timings of the reception of pulsed light from the target. In the present work, the rangefinder generates different sampling intervals of the reference frequency signal: different numbers of sampling points within the period of a reference signal, over a wide range. This is accomplished by slightly changing the period of the pulsed light emitted, without changing the synthesizer frequency which generates the period. This technique requires a minimum of additional hardware. In this paper, we describe the detail of the selection of the number of sampling points based on Lagrange's theorem. And we demonstrate a possibility of expanding the sampling interval to the point where an aliasing of the harmonic components of the reference signal occurs by simulations that focus on the calculation of the phase of the fundamental frequency of the reference signal. And we report on the results of rangefinder experiments for a reduction in the number of the sampling points. We have achieved a 10-fold enhancement of speed by selecting 10 sampling points over the results from the previous studies that had 100 sampling points within a period of a reference signal. And we have confirmed that the reduction in sampling points has a very little influence on the linearity, which is an acceptable trade-off for achieving the speed enhancement. This technique, based on Lagrange's theorem in group theory, allows us to control the minimum number of samplings required to calculate distances, so that high-speed data acquisition for coarse measurements and normal-speed data acquisition for fine measurements become selectable. Such a system with high flexibility in measurement modes has been developed.
Daisuke ANZAI Kentaro YANAGIHARA Kyesan LEE Shinsuke HARA
For an indoor area where a target node is tracked with anchor nodes, we can calculate the priori probability density functions (pdfs) on the distances between the target and anchor nodes by using its shape, three-dimensional sizes and anchor nodes locations. We call it “the area layout information (ALI)” and apply it for two indoor target tracking methods with received signal strength indication (RSSI) assuming a square location estimation area. First, we introduce the ALI to a target tracking method which tracks a target using the weighted sum of its past-to-present locations by a simple infinite impulse response (IIR) low pass filter. Second, we show that the ALI is applicable to a target tracking method with a particle filter where the motion of the target is nonlinearly modelled. The performances of the two tracking methods are evaluated by not only computer simulations but also experiments. The results demonstrate that the use of ALI can successfully improve the location estimation performance of both target tracking methods, without huge increase of computational complexity.
Xin ZHANG Yu PU Koichi ISHIDA Yoshikatsu RYU Yasuyuki OKUMA Po-Hung CHEN Takayasu SAKURAI Makoto TAKAMIYA
In this paper, a novel switched-capacitor DC-DC converter with pulse density and width modulation (PDWM) is proposed with reduced output ripple at variable output voltages. While performing pulse density modulation (PDM), the proposed PDWM modulates the pulse width at the same time to reduce the output ripple with high power efficiency. The prototype chip was implemented using 65 nm CMOS process. The switched-capacitor DC-DC converter has 0.2-V to 0.47-V output voltage and delivers 0.25-mA to 10-mA output current from a 1-V input supply with a peak efficiency of 87%. Compared with the conventional PDM scheme, the proposed switched-capacitor DC-DC converter with PDWM reduces the output ripple by 57% in the low output voltage region with the efficiency penalty of 2%.
Lechang LIU Takayasu SAKURAI Makoto TAKAMIYA
A 0.6-V voltage shifter and a 0.6-V clocked comparator are presented for sampling correlation-based impulse radio UWB receiver. The voltage shifter is used for a novel split swing level scheme-based CMOS transmission gate which can reduce the power consumption by four times. Compared to the conventional voltage shifter, the proposed voltage shifter can reduce the required capacitance area by half and eliminate the non-overlapping complementary clock generator. The proposed 0.6-V clocked comparator can operate at 100-MHz clock with the voltage shifter. To reduce the power consumption of the conventional continuous-time comparator based synchronization control unit, a novel clocked-comparator based control unit is presented, thereby achieving the lowest energy consumption of 3.9 pJ/bit in the correlation-based UWB receiver with the 0.5 ns timing step for data synchronization.
Mohiuddin HAFIZ Shinichi KUBOTA Nobuo SASAKI Kentaro KIMOTO Takamaro KIKKAWA
A differential BPSK transmitter for ultra-wideband impulse-radio communication has been presented in this paper. The transmitter, developed in a 65 nm CMOS process,is simple in design and occupies a core area of 0.0017 mm2. The differential Gaussian monocycle pulses (GMP) are generated using some logic blocks and delay elements. The generated GMP, having a center frequency above 5 GHz, meets the FCC regulations. Measured results show that the transmitter consumes 1.8 pJ/bit to transmit BPSK modulated GMP at a data rate of 2 Gb/s. The interface circuitries eliminate the need for external networks for chip to antenna matching. Using an off-chip differential bow-tie antenna, data can easily be transmitted up to a distance of 10 cm which made it suitable for low power far field non-coherent applications.
In this paper, we propose a memory-efficient structure for a pulse Doppler radar in order to reduce the hardware's complexity. The conventional pulse Doppler radar is computed by fast frequency transform (FFT) of all range cells in order to extract the velocity of targets. We observed that this method requires a huge amount of memory to perform the FFT processes for all of the range cells. Therefore, instead of detecting the velocity of all range cells, the proposed architecture extracts the velocity of the targets by using the cells related to the moving targets. According to our simulations and experiments, the detection performance of this proposed architecture is 93.5%, and the proposed structure can reduce the hardware's complexity by up to 66.2% compared with the conventional structure.
Fuminori SAKAI Kazuo OHTA Kunio SAWAYA
A UWB impulse array antenna (IAA) utilizing a novel electrical scanning system with tapped delay lines is proposed and its usefulness is experimentally verified. The experimental antenna is composed of impulse generators installed in each antenna element and tapped delay lines used for creating transmitting trigger signals, which is a simple circuit configuration. It is shown that the output phase of the transmitting wave can be controlled by controlling the period of the trigger signal, and beam direction can be controlled from -30 deg to +30 deg by changing the trigger frequency from Fc-2 kHz to Fc+2 kHz. Evaluation of this antenna as a short range radar is carried out and distance resolution of 25 cm and angle resolution below 10 deg are obtained.
Ryosuke FUJIWARA Kenichi MIZUGAKI Tatsuo NAKAGAWA Daisuke MAEDA Masayuki MIYAZAKI
In this work, a time-of-arrival/time-difference-of-arrival (TOA/TDOA) hybrid relative positioning system based on UWB-IR technology is developed. The system reduces both the complexity of system configuration and the number of wireless transmissions in a positioning sequence. The system performance over various distances between access points is verified by computer simulations and experiments under the assumption that the distance between the access points is less than that between the access point and the target node. For the experiments, the proposed system is implemented with in-house developed UWB transceivers. The experiments confirm that the developed TOA/TDOA hybrid system can detect the relative positions of target nodes (under the condition of two access points 4 m apart) with a measured-angle accuracy of 8.6 degrees.
Yuji MATSUKI Takuya SAKAMOTO Toru SATO
UWB (ultra wide-band) pulse radar is a promising candidate for surveillance systems. The fast SEABED (Shape Estimation Algorithm based on BST and Extraction of Directly scattered waves) imaging algorithm is deployed in the application of UWB pulse radar in fields that require real-time operations. However, since the SEABED algorithm uses signals received at multiple locations, this method either needs to scan antennas or to install many antennas. Such systems are inevitably costly and unrealistic for applications such as surveillance. To overcome this problem, a revised SEABED algorithm that estimates unknown target shape based on target motion using only a pair of fixed antennas was developed. However, the method cannot be used when the target moves arbitrarily because it assumes the target motion is parallel to the baseline of the pair of antennas. In this paper, we propose a new UWB radar imaging algorithm that is applicable even for targets with arbitrary motion. The proposed method introduces another antenna which is added to the pair of antennas used in the revised SEABED, and estimates unknown target motion based on the target surface using the three antennas. Next, the proposed method applies the SEABED imaging algorithm to the estimated motion and obtains the target image. Some numerical simulations establishes that the proposed method can accurately estimate the target shape even under severe conditions.
Ryosuke FUJIWARA Kenichi MIZUGAKI Goichi ONO Tatsuo NAKAGAWA Takayasu NORIMATSU Takahide TERADA Akira MAEKI Masayuki MIYAZAKI
In this work, an ultra-wideband impulse radio (UWB-IR) transceiver with accurate time-of-arrival (TOA) estimation for a ranging/positioning system was developed for wireless sensor network applications. The system uses an impulse radio characterized by a low duty cycle and direct-sequence spreading, which enable very precise ranging and good receiver sensitivity. An algorithm enabling the TOA of the first-path signal to be measured accurately in a multi-path environment with simple, low-power and low cost implementations was proposed. UWB chips with CMOS 0.18-µm technology and UWB transceiver modules performed that the accuracy of the proposed ranging system is 18.5 cm in a closed space.
Noriyoshi KAMADO Haruhide HOKARI Shoji SHIMADA Hiroshi SARUWATARI Kiyohiro SHIKANO
In this paper, we present a comparative study on directly aligned multi point controlled wavefront synthesis (DMCWS) and wave field synthesis (WFS) for the realization of a high-accuracy sound reproduction system, and the amplitude, phase and attenuation characteristics of the wavefronts generated by DMCWS and WFS are assessed. First, in the case of DMCWS, we derived an optimal control-line coordinate based on a numerical analysis. Next, the results of computer simulations revealed that the wavefront in DMCWS has wide applicability in both the spatial and frequency domains with small amplitude and phase errors, particularly above the spatial aliasing frequency in WFS, and we clarified that the amplitude error in DMCWS has similar behavior to the well-known approximate expression for spatial decay in WFS; this implies the ease of taking into account estimating the amplitude error in DMCWS. Finally, we developed wavefront measurement system and measured a DMCWS wavefront using our wavefront measurement system and algorithm. The results of measurements clarified the frequency characteristics of a loudspeaker. Also, DMCWS has wide applicability in frequency domains in actual environments. From these findings, we concluded the advantageousness of DMCWS compared with WFS.
Nobu-hisa KANEKO Michitaka MARUYAMA Chiharu URANO
AC-waveform synthesis with quantum-mechanical accuracy has been attracting many researchers, especially metrologists in national metrology institutes, not only for its scientific interest but its potential benefit to industries. We describe the current status at National Metrology Institute of Japan of development of a Josephson arbitrary waveform synthesizer based on programmable and pulse-driven Josephson junction arrays.
Kozo HISAMATSU Toshimichi SAITO
This letter studies a pulse-coupled system constructed by delayed cross-switching between two bifurcating neurons. The system can exhibit an interesting bifurcation: the delay-coupling can change chaotic behavior of single neurons into stable periodic behavior. Using the 1D phase map, it is clarified that the phenomenon is caused by the tangent bifurcation for the delay parameter. Presenting a simple test circuit, the phenomenon can be confirmed experimentally.
Pengyu GUAN Hans Christian Hansen MULVAD Yutaro TOMIYAMA Toshiyuki HIRANO Toshihiko HIROOKA Masataka NAKAZAWA
We demonstrate a single-channel 1.28 Tbit/s-525 km transmission using OTDM of subpicosecond DQPSK signals. In order to cope with transmission impairments due to time-varying higher-order PMD, which is one of the major limiting factors in such a long-haul ultrahigh-speed transmission, we newly developed an ultrafast time-domain optical Fourier transformation technique in a round-trip configuration. By applying this technique to subpicosecond pulses, transmission impairments were greatly reduced, and BER performance below FEC limit was obtained with increased system margin.
Jinhua LIU Guican CHEN Hong ZHANG
This paper presents a systemic analysis for phase noise performances of the series quadrature oscillator (QOSC) by using the time-variant impulse sensitivity function (ISF) model. The effective ISF for each noise source in the oscillator is derived mathematically. According to these effective ISFs, the explicit closed-form expression for phase noise due to the total thermal noise in the series QOSC is derived, and the phase noise contribution from the flicker noise in the regenerative and coupling transistors is also figured out. The phase noise contributions from the thermal noise and the flicker noise are verified by SpectreRF simulations.
Mohiuddin HAFIZ Nobuo SASAKI Takamaro KIKKAWA
A CMOS detection procedure for ultra-wideband impulse radio (UWB-IR) communication system, employing Bi-Phase Shift Keying (BPSK) modulation scheme, is presented here. The chip was designed and fabricated in a 180 nm CMOS process and it requires a supply voltage of 1.8 V, with a die area of 0.01 mm2. A train of Gaussian Monocycle Pulses (GMP), modulated by a random data sequence of 1 Gb/s, has been detected successfully by the detector. Ability to process differential data without using conventional blocks like mixer, correlator etc. while consuming a very low power (3.8 pJ/bit for a data rate of 1 Gb/s) is the novelty of this work. The detection scheme employing a simple architecture with a noncoherent detection mechanism is well suited for UWB-IR communication system.