This paper presents the design of a capacitive coupler for underwater wireless power transfer focused on the landing direction of a drone. The main design feature is the relative position of power feeding/receiving points on the coupler electrodes, which depends on the landing direction of the drone. First, the maximum power transfer efficiencies of coupled lines with different feeding positions are derived in a uniform dielectric environment, such as that realized underwater. As a result, these are formulated by the coupling coefficient of the capacitive coupler, the unloaded qualify factor of dielectrics, and hyperbolic functions with complex propagation constants. The hyperbolic functions vary depending on the relative positions and whether these are identical or opposite couplers, and the efficiencies of each coupler depend on the type of water, such as seawater and tap water. The design method was demonstrated and achieved the highest efficiencies of 95.2%, 91.5%, and 85.3% in tap water at transfer distances of 20, 50, and 100 mm, respectively.

The misalignment of a coupler is a significant issue for capacitive wireless power transfer (WPT). This paper presents a capacitive WPT system specifically designed for underwater drones operating in flowing freshwater environments. The primary design features include a capacitive coupler with an opposite relative position between feeding and receiving points on the coupler electrode, two phase compensation circuits, and a load-independent inverter. A stable and energy-efficient power transmission is achieved by maintaining a 90° phase difference on the coupler electrode in dielectrics with a large unloaded quality factor (Q factor), such as in freshwater. Although a 622-mm coupler electrode is required at 13.56MHz, the phase compensation circuits can reduce to 250mm as one example, which is mountable to small underwater drones. Furthermore, the electricity waste is automatically reduced using the constant-current (CC) output inverter in the event of misalignment where efficiency drops occur. Finally, their functions are simulated and demonstrated at various receiver positions and transfer distances in tap water.

Frame synchronization detection before data transmission is an important module which directly affects the lifetime and coexistence of underwater acoustic communication (UAC) networks, where linear frequency modulation (LFM) is a frame preamble signal commonly used for synchronization. Unlike terrestrial wireless communications, strong bursty noise frequently appears in UAC. Due to the long transmission distance and the low signal-to-noise ratio, strong short-distance bursty noise will greatly reduce the accuracy of conventional fractional fourier transform (FrFT) detection. We propose a multi-segment verification fractional fourier transform (MFrFT) preamble detection algorithm to address this challenge. In the proposed algorithm, 4 times of adjacent FrFT operations are carried out. And the LFM signal identifies by observing the linear correlation between two lines connected in pair among three adjacent peak points, called ‘dual-line-correlation mechanism’. The accurate starting time of the LFM signal can be found according to the peak frequency of the adjacent FrFT. More importantly, MFrFT do not result in an increase in computational complexity. Compared with the conventional FrFT detection method, experimental results show that the proposed algorithm can effectively distinguish between signal starting points and bursty noise with much lower error detection rate, which in turn minimizes the cost of retransmission.

With the gradually increase of the application of new energy in microgrids, Electric Spring (ES), as a new type of distributed compensation power electronic device has been widely studied. The Generalized Electric Spring (G-ES) is an improved topology, and the space limitation problem in the traditional topology is solved. Because of the mode of G-ES use in the power grid, a reasonable solution to the voltage loss of the critical section feeder is needed. In this paper, the voltage balance equation based on the feedforward compensation coefficient is established, and a two cascade control strategy based on the equation is studied. The first stage of the two cascade control strategy is to use communication means to realize the allocation of feedforward compensation coefficients, and the second stage is to use the coefficients to realize feedforward fixed angle control. Simulation analysis shows that the proposed control strategy does not affect the control accuracy of the critical load (CL), and effectively improves the operational range of the G-ES.

Message franking is introduced by Facebook in end-to-end encrypted messaging services. It allows to produce verifiable reports of malicious messages by including cryptographic proofs, called reporting tags, generated by Facebook. Recently, Grubbs et al. (CRYPTO'17) proceeded with the formal study of message franking and introduced committing authenticated encryption with associated data (CAEAD) as a core primitive for obtaining message franking. In this work, we aim to enhance the security of message franking and introduce forward security and updates of reporting tags for message franking. Forward security guarantees the security associated with the past keys even if the current keys are exposed and updates of reporting tags allow for reporting malicious messages after keys are updated. To this end, we firstly propose the notion of key-evolving message franking with updatable reporting tags including additional key and reporting tag update algorithms. Then, we formalize five security requirements: confidentiality, ciphertext integrity, unforgeability, receiver binding, and sender binding. Finally, we show a construction of forward secure message franking with updatable reporting tags based on CAEAD, forward secure pseudorandom generator, and updatable message authentication code.

Underwater acoustic channels (UWA) are usually sparse, which can be exploited for adaptive equalization to improve the system performance. For the shallow UWA channels, based on the proportional minimum symbol error rate (PMSER) criterion, the adaptive equalization framework requires the sparsity selection. Since the sparsity of the L0 norm is stronger than that of the L1, we choose it to achieve better convergence. However, because the L0 norm leads to NP-hard problems, it is difficult to find an efficient solution. In order to solve this problem, we choose the Gaussian function to approximate the L0 norm. Simulation results show that the proposed scheme obtains better performance than the L1 based counterpart.

We present a forward-secure public-key encryption (PKE) scheme without key update, i.e. both public and private keys are immutable. In contrast, prior forward-secure PKE schemes achieve forward security by constantly updating the secret keys. Our scheme is based on witness encryption by Garg et al. (STOC 2013) and a proof-of-stake blockchain with the distinguishable forking property introduced by Goyal et al. (TCC 2017), and ensures a ciphertext cannot be decrypted more than once, thereby rendering a compromised secret key useless with respect to decryption of past ciphertext the legitimate user has already decrypted. In this work, we formalize the notion of blockchain-based forward-secure PKE, show the feasibility of constructing a forward-secure PKE scheme without key update, and discuss interesting properties of our scheme such as post-compromise security.

Currently, NDN-based VANETs protocols have several problems with packet overhead of rebroadcasting, control packet, and the accuracy of next-hop selection due to the dynamic topology. To deal with these problems in this paper, we propose a robust and lightweight forwarding protocol in Vehicular ad-hoc Named Data Networking. The concept of our forwarding protocol is adopting a packet-free approach. A vehicle collects its neighbor's visual identification by a pair of cameras (front and rear) to assign a unique visual ID for each node. Based on these IDs, we construct a hop-by-hop FIB-based forwarding strategy effectively. Furthermore, the Face duplication [1] in the wireless environment causes an all-broadcast problem. We add the visual information to Face to distinguish the incoming and outgoing Face to prevent broadcast-storm and make FIB and PIT work more accurate and efficiently. The performance evaluation results focusing on the communication overhead show that our proposal has better results in overall network traffic costs and Interest satisfaction ratio than previous works.

In this letter, we consider a global stabilization problem for a class of feedforward systems by an event-triggered control. This is an extended work of [10] in a way that there are uncertain feedforward nonlinearity and time-varying input delay in the system. First, we show that the considered system is globally asymptotically stabilized by a proposed event-triggered controller with a gain-scaling factor. Then, we also show that the interexecution times can be enlarged by adjusting a gain-scaling factor. A simulation example is given for illustration.

To improve the performance of underwater acoustic communications, this letter proposes a polar coding scheme with adaptive channel equalization, which can reduce the amount of feedback information. Furthermore, a hybrid automatic repeat request (HARQ) mechanism is provided to mitigate the impact of estimation errors. Simulation results show that the proposed scheme outperforms the turbo equalization in bit error rate. Computational complexity analysis is also provided for comparison.

This paper proposes a new multi-port amplifier configuration that employs feed-forward techniques. In general, a multi-port amplifier is used as a transponder in a satellite transmitter. A multi-port amplifier comprises an N-in N-out input-side matrix network, N amplifiers, and an N-in N-out output-side matrix network. Based on this configuration, other undesired ports leak power to the desired port in a multi-port amplifier. If the power amplifier of a cellular base station uses a multi-port amplifier, the power leakage from the other ports causes degradation in the error vector magnitude. The proposed configuration employs N-parallel feed-forward amplifiers with a multi-port amplifier as the main amplifier. The proposed configuration drastically reduces the power leakage using the employed feed-forward techniques. An experimental 2-GHz band four-in four-out multi-port amplifier is constructed and tested. It achieves the leakage power level of -58 dB, a gain deviation of less than 0.05 dB, and a phase deviation of less than 0.45 deg. with the maximum power of 35 dBm over a 20-MHz bandwidth with the center frequency 2.14 GHz at room temperature. The experimental multi-port amplifier reduces the leakage power level by approximately 30 dB compared to that for a multi-port amplifier without the feed-forward techniques. The proposed configuration can be applied to power amplifiers in cellular base stations.

The performance of conventional direction of arrival (DOA) methods is susceptible to the uncertainty of acoustic velocity in the underwater environment. To solve this problem, an underwater DOA estimation method with L-shaped array for wide-band signals under unknown acoustic velocity is proposed in this paper. The proposed method refers to the idea of incoherent signal subspace method and Root-MUSIC to obtain two sets of average roots corresponding to the subarray of the L-shaped array. And the geometric relationship between two vertical linear arrays is employed to derive the expression of DOA estimation with respect to the two average roots. The acoustic velocity variable in the DOA estimation expression can be eliminated in the proposed method. The simulation results demonstrate that the proposed method is more accurate and robust than other methods in an unknown acoustic velocity environment.

In this paper, we propose applying our previously reported adaptive peak-to-average power ratio (PAPR) reduction method using null space in a multiple-input multiple-output (MIMO) channel for orthogonal frequency division multiplexing (OFDM) signals to the downlink MIMO amplify-and-forward (AF) relaying transmission. Assuming MIMO-OFDM transmission, mitigating its high PAPR not only at the base station (BS) but also at the relay station (RS) transmitters is essential to achieve sufficient coverage enhancement from the RSs by minimizing the transmission power backoff levels at the nonlinear power amplifier. In this study, we assume an AF-type RS with multiple antennas. In the proposed method, the BS suppresses the PAPR of the transmitted signal through adaptive PAPR reduction utilizing the null space of the integrated overall MIMO channel that combines the channel between the BS and RS and the channel between the RS and a set of user equipment (UE). However, the PAPR of the received signal at each RS antenna is increased again due to the MIMO channel between the BS and RS. The proposed method reduces this increased PAPR at the AF-type RS transmitter by PAPR reduction processing that utilizes the null space in the MIMO channel between the RS and UE. Since the in-band PAPR reduction signal added at the RS transmitter is transmitted only in the null space of the MIMO channel between the RS and UE, interference at the UE receiver is mitigated. Computer simulation results show that the proposed method significantly improves the PAPR-vs.-throughput performance compared to that for the conventional one thanks to the reduced interference levels from the PAPR reduction signal observed at the UE receiver.

In this study, we consider fake message attacks in sparse mobile ad hoc networks, in which nodes are chronically isolated. In these networks, messages are delivered to their destination nodes using store-carry-forward routing, where they are relayed by some nodes. Therefore, when a node has messages in its buffer, it can falsify the messages easily. When malicious nodes exist in the network, they alter messages to create fake messages, and then they launch fake message attacks, that is, the fake messages are spread over the network. To analyze the negative effects of a fake message attack, we model the system dynamics without attack countermeasures using a Markov chain, and then formalize some performance metrics (i.e., the delivery probability, mean delivery delay, and mean number of forwarded messages). This analysis is useful for designing countermeasures. Moreover, we consider a hash-based countermeasure against fake message attacks using a hash of the message. Whenever a node that has a message and its hash encounters another node, it probabilistically forwards only one of them to the encountered node. By doing this, the message and the hash value can be delivered to the destination node via different relay nodes. Therefore, even if the destination node receives a fake message, it can verify the legitimacy of the received message. Through simulation experiments, we evaluate the effectiveness of the hash-based countermeasure.

In this paper, to improve communication system's energy-efficiency (EE), multi-case optimization of two new transmission strategies is investigated. Firstly, with amplify-and-forward relaying and full-duplex technique, two new transmission strategies are designed. The designed transmission strategies consider direct links and non-ideal transmission conditions. At the same time, detailed capacity and energy consumption analyses of the designed transmission strategies are given. In addition, EE optimization and analysis of the designed transmission strategies are studied. It is the first case of EE optimization and it is achieved by joint optimization of transmit time (TT) and transmit power (TP). Furthermore, the second and third cases of EE optimization with respectively optimizing TT and TP are given. Simulations reveal that the designed transmission strategies can effectively improve the communication system's EE.

Software-defined networking (SDN) decouples the control and forwarding of network devices, providing benefits such as simplified control. However, due to cost constraints and other factors, SDN is difficult to fully deploy. It has been proposed that SDN devices can be incrementally deployed in a traditional IP network, i.e., hybrid SDN, to provide partial SDN benefits. Studies have shown that better traffic engineering performance can be achieved by modifying the coverage and placement of SDN devices in hybrid SDN, because they can influence the behavior of legacy switches through certain strategies. However, it is difficult to develop and execute a traffic engineering strategy in hybrid SDN. This article proposes a routing algorithm to achieve approximate load balancing, which minimizes the maximum link utilization by using the optimal solution of linear programming and merging the minimum split traffic flows. A multipath forwarding mechanism under the same problem is designed to optimize transmission time. Experiments show that our algorithm has certain advantages in link utilization and transmission time compared to traditional distributed routing algorithms like OSPF and some hybrid SDN routing mechanisms. Furthermore, our algorithm can approximate the control effect of full SDN when the deployment rate of SDN devices is 40%.

This paper presents linearization technologies for high efficiency power amplifiers of cellular base stations. These technologies are important to actualizing highly efficient power amplifiers that reduce power consumption of the base station equipment and to achieving a sufficient non-linear distortion compensation level. It is well known that it is very difficult for a power amplifier using linearization technologies to achieve simultaneously high efficiency and a sufficient non-linear distortion compensation level. This paper presents two approaches toward addressing this technical issue. The first approach is a feed-forward power amplifier using the Doherty amplifier as the main amplifier. The second approach is a digital predistortion linearizer that compensates for frequency dependent intermodulation distortion components. Experimental results validate these approaches as effective for providing power amplification for base stations.

Deep neural network (DNN)-based speech synthesis became popular in recent years and is expected to soon be widely used in embedded devices and environments with limited computing resources. The key intention of these systems in poor computing environments is to reduce the computational cost of generating speech parameter sequences while maintaining voice quality. However, reducing computational costs is challenging for two primary conventional DNN-based methods used for modeling speech parameter sequences. In feed-forward neural networks (FFNNs) with maximum likelihood parameter generation (MLPG), the MLPG reconstructs the temporal structure of the speech parameter sequences ignored by FFNNs but requires additional computational cost according to the sequence length. In recurrent neural networks, the recursive structure allows for the generation of speech parameter sequences while considering temporal structures without the MLPG, but increases the computational cost compared to FFNNs. We propose a new approach for DNNs to acquire parameters captured from the temporal structure by backpropagating the errors of multiple attributes of the temporal sequence via the loss function. This method enables FFNNs to generate speech parameter sequences by considering their temporal structure without the MLPG. We generated the fundamental frequency sequence and the mel-cepstrum sequence with our proposed method and conventional methods, and then synthesized and subjectively evaluated the speeches from these sequences. The proposed method enables even FFNNs that work on a frame-by-frame basis to generate speech parameter sequences by considering the temporal structure and to generate sequences perceptually superior to those from the conventional methods.

This paper presents analysis results of the intermodulation distortion (IMD) components compensation conditions for dual-band feed-forward power amplifier (FFPA) when inputting dual-band signals simultaneously. The signal cancellation loop and distortion cancellation loop of the dual-band FFPA have frequency selective adjustment paths which consist of filter and vector regulator. The filter selects the desired frequency component and suppresses the undesired frequency component in the desired frequency selective adjustment path. The vector regulators repeatedly adjust the amplitude and phase values of the composite components for the desired and suppressed undesired frequency components. In this configuration, the cancellation levels of the signal cancellation loop and distortion cancellation loop are depending on the amplitude and phase errors of the vector regulator. The analysis results show that the amplitude and phase errors of the desired frequency component almost become independent that of the undesired frequency component in a weak non-linearity condition, when the isolation between the desired band and the undesired band given by the filter is more than 40 dB. The amplitude errors of the desired frequency component are dependent on that of the undesired frequency component in a strong non-linear conditions when the isolation level sets as above. A 1-W-class signal cancellation loop and 20-W-class FFPA are fabricated for 1.7-GHz and 2.1-GHz bands simultaneous operation. The experimental results show that the analysis results are suitable in the experimental conditions. From these investigations, the analysis results can provide a commercially available dual-band FFPA. To our best knowledge, this is first analysis results for the dual-band FFPA.

With increasing technology scaling and the use of lower voltages, more research interest is being shown in variability-tolerant analog front end design. In this paper, we describe an adaptive amplitude control transmitter that is operated using differential signaling to reduce the temperature variability effect. It enables low power, low voltage operation by synergy between adaptive amplitude control and Vth temperature variation control. It is suitable for high-speed interface applications, particularly cable interfaces. By installing an aggressor circuit to estimate transmitter jitter and changing its frequency and activation rate, we were able to analyze the effects of the interface block on the input buffer and thence on the entire system. We also report a detailed estimation of the receiver clock-data recovery (CDR) operation for transmitter jitter estimation. These investigations provide suggestions for widening the eye opening of the transmitter.