In order to reduce the peak-to-average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals over fading channels, the selected mapping (SLM) scheme and channel estimation technique can be used. Because of the side information of SLM, however, the data rate decreases in the conventional transmission method. In this letter, to overcome this impairment, we propose a technique which transmits side information by using pilot tones. Numerical analysis and computer simulations show that this method can maintain the PAPR reduction ability of SLM while improving error performance.

We propose a new filter method for feature selection for SELDI-TOF mass spectrum datasets. In the method, a new relevance index was defined to represent the goodness of a feature by considering the distribution of samples based on the counts. The relevance index can be used to obtain the feature sets for classification. Our method can be applied to mass spectrum datasets with extremely high dimensions and process the clinical datasets with practical sizes in acceptable calculation time since it is based on simple counting of samples. The new method was applied to the three public mass spectrum datasets and showed better or comparable results than conventional filter methods.

The wireless systems that establish multiple input multiple output (MIMO) channels through multiple antennas at both ends of the communication link, have been proved to have tremendous potential to linearly lift the capacity of conventional scalar channel. In this paper, we present two efficient decision feedback equalization algorithms that achieve optimal and suboptimal detection order in MIMO spatial multiplexing systems. The new algorithms combine the recursive matrix inversion and ordered QR decomposition approaches, which are developed for nulling cancellation interaface Bell Labs layered space time (BLAST) and back substitution interface BLAST. As a result, new algorithms achieve total reduced complexities in frame based transmission with various payload lengths compared with the earlier methods. In addition, they enable shorter detection delay by carrying out a fast hybrid preprocessing. Moreover, the operation precision insensitivity of order optimization greatly relaxes the word length of matrix inversion, which is the most computational intensive part within the MIMO detection task.

This paper analyzes the spurious sources in DDS synthesizers and deduces the simple model of DDS output signal. The method of feeding pseudo-random noise into the phase accumulator for spurious reduction is discussed. A new method for spurious reduction by compensating for DAC integer nonlinearity is proposed with two DACs and a power combiner. One DAC generates the error signal to compensate for the other DAC INL. The factor how the amplitude error and the phase error between the two combined signals affect the spurious level is also analyzed. The experiment shows that the spurious reduction can be improved by at least 18 dB, which proves the validity of the DAC INL compensation method for the spurious reduction.

The deployment of historical trajectories of moving objects has greatly increased for various applications in road networks. For instance, similar patterns of moving-object trajectories are very useful for designing the transportation network of a new city. In this paper, we define a spatio-temporal similarity measure based on a road network distance, rather than a Euclidean distance. We also propose a new similar trajectory search algorithm based on the spatio-temporal measure by using an efficient pruning mechanism. Finally, we show the efficiency of our algorithm, both in terms of retrieval accuracy and retrieval efficiency.

An AuSn reflow process using hydrogen radicals as a way to avert the cleaning of flux residues was investigated for its application to solder bumping. AuSn particles (manufactured by a gas atomizer) smaller than 5 µm, which are difficult to reflow by conventional methods that use rosin mildly activated (RMA) flux, were used for the experiments. In this process, the reduction effect by the hydrogen radicals removes the surface oxides of the AuSn particles. Excellent wetting between 1-µm-diameter AuSn particles and Ni metallization occurred in hydrogen plasma. Using hydrogen radicals, 100 µm-diameter AuSn bumps without voids were successfully formed at a peak temperature of 300. The average bump shear strength was approximately 73 gf/bump. Bump inspection after shear testing showed that a fracture had occurred between the Au/Ni/Cr under bump metallurgy (UBM) and Si substrate, suggesting sufficient wetting between the AuSn bump and the UBM.

In low bit-rate video transmission, the payload of a single packet can often contain a whole coded frame due to the high compression ratio in both spatial and temporal domains. Thus, the loss of a single packet can lead to the loss of a whole video frame. In this paper, we propose a novel error concealment algorithm that can effectively reconstruct the lost frame and protect the quality of video streams from the degradation caused by propagation errors. The proposed algorithm employs a bilateral motion estimation scheme where the weighted sum of the received motion vectors (MVs) in the neighboring frames is utilized to construct the MV field for the concealed frame. Unlike the conventional algorithms, the proposed scheme does not produce any overlapped pixel and hole region in the reconstructed frame. The proposed algorithm can be applied not only to the case of single frame loss but also adaptively extended to the case of multiframe loss. Experimental results show that the proposed algorithm outperforms other conventional techniques in terms of both peak signal-to-noise ratio (PSNR) performance and subjective visual quality.

The authors present R2Power, an effective approach to the realizable reduction of RC networks with independent current sources. The proposed approach is based on the entrywise perturbation theory for diagonally dominant M-matrices. The accuracy of the node voltages of the reduced network, as compared to those of the original network, is maintained on the order of the entrywise perturbation performed during reduction. R2Power can be used to reduce the size of RC networks used to model the power networks of SoCs, for efficient IR-drop analysis. Experiments showed that R2Power reduced the size of industrial examples by more than 95%, with maximum relative node voltage errors of less than 0.012%.

As a method to realize a high-speed communication in the home network, the power-line communication (PLC) technique is known. A problem of PLC is that leakage radiation interferes with existing systems. When OFDM is used in a PLC system, the leakage radiation is not sufficiently reduced, even if the subcarriers corresponding to the frequency-band of the existing system are never used, because the signal is not strictly band-limited. To solve this problem, each subcarrier must be band-limited. In this paper, we apply the OQAM based multi-carrier transmission (OQAM-MCT) to a high-speed PLC system, where each subcarrier is individually band-limited. We also propose a pilot-symbol sequence suitable for frequency offset estimation, symbol-timing detection and channel estimation in the OQAM-MCT system. In this method, the pilot signal-sequence consists of a repeated series of the same data symbol. With this method, the pilot sequence approximately becomes equivalent to OFDM sequence and therefore existing pilot-assisted methods for OFDM are also applicable to OQAM-MCT system. Computer simulation results show that the OQAM-MCT system achieves both good transmission rate performance and low out-of-band radiation in PLC channels. It is also shown that the proposed pilot-sequence improves frequency offset estimation, symbol-timing detection and channel estimation performance as compared with the case of using pseudo-noise sequence.

This paper is concerned with timing synchronization of high rates UWB signals operating in a dense multipath environment, where access must tackle inter-frame interference (IFI), inter-symbol interference (ISI) and even multi-user interference (MUI). A training-based joint timing and channel estimation scheme is proposed, which is resilient to IFI, ISI, MUI and pulse distortion. A low-complexity detection scheme similar to transmit-reference (TR) scheme comes out as a by-product. For saving the training symbols, we further develop an extended decision-directed (DD) scheme. A lower bound on the probability of correct detection is derived which agrees well with the simulated result for moderate to high SNR values. The results show that the proposed algorithm achieves a significant performance gain in terms of mean square error and bit error rate in comparison to the "timing with dirty templates" (TDT) algorithms.

Several problems in built-in-jitter-measurement (BIJM) system designs have been identified in recent years. The problems are associated with the external low-jitter sampling clock, chip area, timing resolution, or the measurement range via the process voltage temperature (PVT) variation effect. In this work, there are three proposed approaches and one conventioanl method that improve BIJM systems. For the system level, a proposed real equivalent-signal sampling technique is utilized to clear the requirement of the external low-jitter sampling clock. The proposed Vernier caliper structure is applied to reduce chip area cost for the designated timing resolution. At the circuit level, the proposed auto focus technique eliminates the PVT variation effect for the measurement range. The stepping scan technique is the conventional method that employed to minimize the area cost of counter circuits. All of these techniques were implemented in the 0.35 µm CMOS process. Furthermore, these techniques are successfully verified in 14 ps circuit resolution and a 500*750 µm chip area for the 100-400 MHz measurement range.

A novel bimodal method for face recognition under low-level lighting conditions is proposed. It fuses an enhanced gray level image and an illumination-invariant geometric image at the feature-level. To further improve the recognition performance under large variations in attributions such as poses and expressions, discriminant features are extracted from source images using the wavelet transform-based method. Features are adaptively fused to reconstruct the final face sample. Then FLD is used to generate a supervised discriminant space for the classification task. Experiments show that the bimodal method outperforms conventional methods under complex conditions.

We present a novel model, named Category Constraint-Latent Dirichlet Allocation (CC-LDA), to learn and recognize natural scene category. Previous work had to resort to additional classifier after obtaining image topic representation. Our model puts the category information in topic inference, so every category is represented in a different topics simplex and topic size, which is consistent with human cognitive habit. The significant feature in our model is that it can do discrimination without combined additional classifier, during the same time of getting topic representation. We investigate the classification performance with variable scene category tasks. The experiments have demonstrated that our learning model can get better performance with less training data.

We present a very simple probabilistic, passive attack against the protocols HB and HB+. Our attack presents some interesting features: it requires less captured transcripts of protocol executions when compared to previous results; It makes possible to trade the amount of required transcripts for computational complexity; the value of noise used in the protocols HB and HB+ need not be known.

We propose a stereo transmission technique using infrared rays and pulse density modulation (PDM) for digital wireless audio headphone systems. The main feature of the proposed technique is the use of two channels for transmission: the PDM data channel and the synchronized clock channel. This technique improves receiver characteristics to a noise floor of -80 dB and a second distortion of 62 dB and achieves a very low power consumption of 3.5 mW.

This paper investigates and analyzes the resistive averaging network and interpolation technique to estimate the power consumption of preamplifier arrays in a flash analog-to-digital converter (ADC). By comparing the relative power consumption of various configurations, flash ADC designers can select the most power efficient architecture when the operation speed and resolution of a flash ADC are specified. Based on the quantitative analysis, a compact 5-bit flash ADC is designed and fabricated in a 0.13-µm CMOS process. The proposed ADC consumes 180 mW from a 1.2-V supply and occupies 0.16-mm2 active area. Operating at 3.2 GS/s, the ENOB is 4.44 bit and ERBW 1.65 GHz. At 4.2 GS/s, the ENOB is 4.20 bit and ERBW 1.75 GHz. This ADC achieves FOMs of 2.59 and 2.80 pJ/conversion-step at 3.2 and 4.2 GS/s, respectively.

We present a 10-bit 1-MS/s successive approximation analog-to-digital converter core including a charge redistribution digital-to-analog converter and a comparator. A new linearity calibration technique enables use of a nearly minimum capacitor limited by kT/C noise. The ADC core without digital control blocks has been fabricated in a 0.18-µm CMOS process and consumes 118 µW at 1.8 V power supply. Also, the active area of ADC core is realized to be 0.027 mm2. The calibration improves the SNDR by 13.4 dB and the SFDR by 21.0 dB. The measured SNDR and SFDR at 1 kHz input are 55.2 dB and 73.2 dB respectively.

Eigen-beamforming (EB) transmission for multiple-input multiple-output (MIMO) systems is an effective means to maximize the receiver signal-to-noise ratio (SNR) in a noise-limited environment, but suffers a performance degradation when strong interference signals exist. In this letter, we propose an interference cancellation method for EB signals by constructing a new receive beamforming vector which jointly utilizes the EB matrix and minimum mean-square error (MMSE) spatial demultiplexing. The proposed method is shown to outperform the conventional EB receiver in the entire cell range, with a significant increase in the effective signal-to-interference plus noise ratio (SINR) near the cell boundary.

The comprehensibility of large and complex 3D models can be greatly enhanced by guiding viewer's attention to important regions. Lighting is crucial to our perception of shape. Careful use of lighting has been widely used in art, scientific illustration, and computer graphics to guide visual attention. In this paper, we explore how the saliency of 3D objects can be used to guide lighting to emphasize important regions and suppress less important ones.

A new class of sextic residue sequences of period prime p=4u2+27=6f+1 ≡ 3 ( mod 8) are presented. Their trace function representations are determined. And the exact value of the linear complexity is derived from the trace function representations. The result indicates that the new sextic sequences are quite good from the linear complexity viewpoint.