A superconducting multichip module using Nb/Polyimide on a mullite multilayer ceramic substrate has been developed for Josephson LSI circuits. The Nb/Polyimide stacked layers on the mullite multilayer ceramic substrate makes it possible to fabricate superconducting off-chip wiring for control signal line. We named the MCM "SuperMCM". The superconducting transmission line is designed to have the characteristic impedance of 14 Ω to match with the Josephson devices. The superconducting critical temperature, critical current density and critical current at a via hole are 8.5 K, 8.2105 A/cm2 and 2.5 A, respectively. The SuperMCM also provides matching circuits employing quarter wavelength striplines for driving Josephson LSI circuits at a microwave frequency, and DC bias circuits in the mullite multilayer ceramic substrate. The characteristics of the matching circuit is measured in the frequency range up to 3.6 GHz and the microwave current gain of 20 dB is obtained at 1.2 GHz, which revealed that the SuperMCM has the ability to drive the Josephson LSI circuits at more than 1.2 GHz clock speed.

In this paper, trellis coded modulation with bandwidth expansion is examined. The proposed scheme is a modified Symbol-rate-increased TCM [3]-[5], which allows the bandwidth expansion ratio to be varied to an arbitrary value. The Symbol-rate-increased TCM has been shown to be a particular case of the proposed scheme. Simulation results have clarified that the proposed scheme achieves a significant improvement over an uncoded scheme in an AWGN channel.

Go-Back-N automatic repeat request (GBN ARQ) and Stop-and wait (SW) ARQ schemes are one of fundamental and widely used error control procedures for data communication and computer communication systems. The throughput and delay performances of these ARQ schemes have been analyzed for a random error channel, which could not applicable for a radio channel, for example. In this paper, considering the correlated, noisy channel, we derive the exact formula for the delay of a frame in GBN and SW ARQ schemes. First, the delay formula for the discrete time M[x]/G/1 queueing system with starter. Next, the virtual service time of a frame is found in terms of the decay factor of a two-state Markov chain. As a result, it is shown that the performance of the delay is improved with the larger decay factor.

This paper proposes a dynamically randomized version of DES (called RDES) in which a input-dependent swapping Sk(X) is added onto the right half of the input in each round of DES. This new scheme decreases the probability of success in differential cryptanalysis because it decreases the characteristic probability. Each "best" two-round characteristic probability is analyzed for typical schemes of the RDES: (i) RDES-1 with a simple one-level swapping, (ii) RDES-1' with an optimal one-level swapping, (iii) RDES-2 with a simple two-level swapping, and (iv) RDES-2' with an optimal two-level swapping. The main results are as follows. (a) The differential attacks on the 16-round RDES-1' and the 16-round RDES-2 require more computational time than the exhaustive search. (b) A differential attack is substantially inapplicable to the 16-round RDES-2' because more than 263 chosen plaintext pairs are required. (c) The encryption/decryption speed of the n-round RDES is almost the same as that of the n-round DES.

A uniquely decodable (UD) code pair (C, S) is considered for the two-user binary adder channel. For a class of linear codes C, the maximum independent set of the graph associated with C, which is the second code S, is evaluated. When the rate R1 of C is less than 0.5, there exist UD codes (C, S)'s such that the rate R2 of S exceeds the Khachatrian's and Guo's results in amount.

This paper describes a pipelining universal system of discrete time cellular neural networks (DTCNNs). The new relaxation-based algorithm which is called a Pipelining Gauss Seidel (PGS) method is used to solve the CNN state equations in pipelining. In the systolic system of N processor elements {PEi}, each PEi performs the convolusional computation (CC) of all cells and the preceding PEi-1 performs the CC of all cells taking precedence over it by the precedence interval number p. The expected maximum number of PE's for the speeding up is given by n/p where n means the number of cells. For its application, the encoding and decoding process of moving images is simulated.

A specific signal in most of actual environmental systems fluctuates complicatedly in a non-Gaussian distribution form, owing to various kinds of factors. The nonlinearity of the system makes it more difficult to evaluate the objective system from the viewpoint of internal physical mechanism. Furthermore, it is very often that the reliable observation value can be obtained only within a definite domain of fluctuating amplitude, because many of measuring equipment have their proper dynamic range and the original random wave form is unreliable at the end of amplitude fluctuation. It becomes very important to establish a new signal processing or an evaluation method applicable to such an actually complicated system even from a functional viewpoint. This paper describes a new trial for the signal processing along the same line of the extended regression analysis based on the Bayes' theorem. This method enables us to estimate the response probability property of a complicated system in an actual situation, when observation values of the output response are saturated due to the dynamic range of measuring equipment. This method utilizes the series expansion form of the Bayes' theorem, which is applicable to the non-Gaussian property of the fluctuations and various kinds of correlation information between the input and output fluctuations. The proposed method is newly derived especially by paying our attention to the statistical information of the input-output data without the saturation operation instead of that on the resultantly saturated observation, differing from the well-known regression analysis and its improvement. Then, the output probability distribution for another kind of input is predicted by using the estimated regression relationship. Finally, the effectiveness of the proposed method is experimentally confirmed too by applying it to the actual data observed for indoor and outdoor sound environments.

A new BiCMOS process based on a high-speed bipolar process with 0.5 µm emitter width has been developed using a bonded SOI substrate. Double polysilicon bipolar transistors with the trench isolation, shallow junctions and the pedestal collector implantation provide a high cut-off frequency of 27 GHz. Stress induced device degradation is carefully examined and a low stress trench isolation process is proposed.

Recent achievements in low-voltage and low-power circuit techniques are reported in this paper. DC current in low-voltage CMOS circuits stemming from the subthreshold current in MOS transistors, is effectively reduced by applying switched-power-line schemes. The AC current charging the capacitance in DRAM memory arrays is reduced by a partial activation of array blocks during the active mode and by a charge recycle during the refresh mode. A very-low-power reference-voltage generator is also reported to control the internal chip voltage precisely. These techniques will open the way to using giga-scale LSIs in battery-operated portable equipment.

A novel isolation structure which has a buried insulator between polysilicon electrodes (BIPS) has been developed. The BIPS isolation employs the refilling CVD-oxides in openings between polysilicon electrodes by photoresist etchback process. Device characteristics and parasitic effects of BIPS isolation have been compared with that of LOCOS isolation. Using BIPS isolation, we can almost suppress the narrow-channel effects and achieve the deep submicron isolation. No degradation on the subthreshold decay of devices with BIPS isolation can be obtained. The use of BIPS isolation technology yields a DRAM cell of small area. The successful fabrication of deep submicron devices with BIPS isolation clearly demonstrates that this technology has superior ability to overcome the LOCOS isolation.

We compare interfaces of Nb/AlOx-Al/Nb and Nb/ZrOx-Zr/Nb junctions using secondary ion mass spectroscopy and cross-sectional transmission electron microscopy. We have clarified that an interface of the Nb/AlOx-Al/Nb junction is drastically different from that of the Nb/ZrOxZr/Nb junction. An adsorbed water vapor layer plays an important role in suppressing grain boundary diffusion between Nb and Al at the interface of the Nb/AlOxAl/Nb junction. In depositing Nb and Al at low power and cooling the substrate, it is important to control the formation of the adsorbed water vapor layer for fabricating Nb/AlOx-Al/Nb junctions exhibiting excellent current-voltage characteristics.

We have systematically grown and characterized (Bi, Pb)2Sr2CaCu2Oy (BPSCCO) single crystals, and investigated the tunneling properties and the intrinsic Josephson effects of the single crystals as a function of the nominal composition of Pb, x. It was observed that Pb atoms (ions) were monotonically substituted for Bi atoms (ions) in the (Bi, Pb)-O layers of the crystals with increasing x in a region of 0x0.5, while the modulation structure was maintained in a range of 0x0.3, but disappeared in x0.3, accompanying the decrease of c-lattice parameter and Tc. Moreover, it was found that the energy gaps Δ of BPSCCO depend hardly on x for x0.5, which are about 24 meV, so that the Pb-induced electronic change in the (Bi, Pb)-O layer do not perturb the electronic states in this superconducting system. And it was confirmed that the currentvoltage characteristics of the BPSCCO single crystals had multiple resistive branches corresponding to a series array of several hundreds Josephson junctions, and showed Shapiro steps and zero-crossing steps with the voltage separation of the order of mV resulting from the phase locking of about a hundred Josephson junctions among them under microwave irradiation. The estimated number of junctions gave the concept that the intrinsic Josephson junctions consist of the superconducting block layers and the insulating layers in the BPSCCO single crystals.

This paper describes a new method for joining BiSrCaCuO superconductors (BSCCO) which realizes low microwave loss and high mechanical strength. This method consists of two processes. In the first the BSCCO surface is metallized with Ag and in the second a joint is formed by using thermally curable Ag paste. With this method, we obtained a joint with a loss of 0.3 dB around 1.1 GHz with the co-axial cavity techniques. Furthermore, the mechanical strength of the joint was greater than that of the BSCCO sample. From the results of DC resistance measurements and SEM observations, we attribute this good performance to the adhesion and continuity of the metallized Ag with the BSCCO surface.

The progress of LSI technologies makes it possible to fabricate 256 MDRAM. However, it depends on the cost effectiveness of device fabrication that LSI memory can continue to be the technology driver or not. It is indispensable to make the device, process, and equipment as simple as possible for next generation LSI. For example, wavefront technologies in lithography, high energy ion implantation, and simple DRAM cell with SOI structure or high dielectric constant capacitor, are under development to satisfy both device performance improvement and process simplicity.

The performance of multi-pulse pulse position modulation (MPPM) consisting of m slots and 2 pulses, denoted as (m, 2) MPPM, with imperfect slot synchronization is analyzed. The word error probability of (m, 2) MPPM in the presence of timing offset is analyzed, and the optimum symbol sets of (m, 2) MPPM minimizing the symbol error probability are assigned. When an unassigned symbol is detected, the receiver decodes the unassigned symbol as one of the assigned symbols having the highest probability of transition from the assigned symbol to the unassigned symbol. The bit error probability of (m, 2) MPPM in the presence of the timing offset is analyzed, and the bit error probability of (m, 2) MPPM is compared with that of PPM for the same transmission bandwidth and the same transmission rate. Moreover, the bit error probability of (m, 2) MPPM synchronized by a phase-locked loop (PLL) is also analyzed. It is shown that a word with two continuous pulses has better performance than a word with two separate pulses. It is also shown that when the timing offset occurs, and when the slot clock is synchronized by a PLL, (m, 2) MPPM performs better than PPM because (m, 2) MPPM has the optimum assigned symbols, and can decode detected words more correctly than PPM.

A new recursive method for obtaining the mean waiting time in a polling system with general service order and gated service discipline is proposed. The analytical approach used to obtain the mean waiting time is via an imbedded Markov chain and a new recursive method is used to obtain the moments of pseudocycle time which are parameters in the formula for the mean waiting time. This method is computationally tractable, so the analytical results can cover a wide range of applications. Simulations are also conducted to verify the validity of the analysis.

Almost stoichiometric YBa2Cu3O7-δ(110) or (103) and SrTiOx(110) films, and multilayer films consisting of them have successfully been grown epitaxially on hot SrTiO3 substrates by 90off-axis rf magnetron sputtering with facing targets. Their whole composition, compositional distribution in depth, crystallinity and surface morphology were examined by inductively coupled plasma spectroscopy, Auger electron spectroscopy, reflection high-energy electron diffraction, and scanning tunneling microscopy or atomic force microscope, respectively. When any YBa2Cu3O7-δ film was exposed to air after deposition, a Ba-rich layer was formed in a near surface region of the film. However, such a compositional distribution in depth of the film was improved by in situ deposition of a SrTiOx film on it. Moreover, the surface roughness of the YBa2Cu3O7-δ film was improved by predeposition of a SrTiOx film under it. On the basis of these results, both YBa2Cu3O7-δ/SrTiOx/YBa2Cu3O7-δ/SrTiO3(sub.) and YBa2Cu3O7-δ/SrTiOx/YBa2Cu3O7-δ/SrTiOx/SrTiO3(sub.) multilayer films with average surface roughness of 3 nm were grown reproducibly, which had uniform compositional distribution throughout the depth of the film except a near surface region of the top YBa2Cu3O7-δ layer. A new 222 structure described by Sr8Ti8O20 (Sr2Ti2O5) with a long range ordered arrangement of oxygen vacancies was formed in the SrTiOx films deposited epitaxially on YBa2Cu3O7-δ films.

This paper proposes a repairable and diagnosable k-valued cellular array. We assume a single fault, i.e., either stuck-at-O fault or stuck-at-(k1) fault of switches occurs in the array. By building in a duplicate column iteratively, when a stuck-at-(k1) fault occurs in the array, the fault never influences the output of the array. That is, we can construct a fault-tolerant array for the stuck-at-(k1) fault. While, for the stuck-at-O fault, the diagnosing method is simple and easy because we don't have to diagnose the stuck-at-(k1) fault. Moreover, our array can be repaired easily for the fault. The comparison with other rectangular arrays shows that our array has advantages for the number of cells and the cost of the fault diagnosis.

An annoying problem encountered in automatic seal imprint verification is that for seal imprints may have a lot of variations, even if they are all produced from a single seal. This paper proposes a new automatic seal imprint verification system which adds an imprint quality assessment function to our previous system in order to solve this problem, and also examines the verification performance of this system experimentally. This system consists of an imprint quality assessment process and a verification process. In the imprint quality assessment process, an examined imprint is first divided into partial regions. Each partial region is classified into one of three quality classes (good quality region, poor quality region, and background) on the basis of characteristics of its gray level histogram. In the verification process, only good quality partial regions of an examined imprint are verified with registered one. Finally, the examined imprint is classified as one of two types: a genuine and a forgery. However, as a result of quality assessment, if the partial regions classified as poor quality are too many, the examined imprint is classified as ambiguous" without verification processing. A major advantage of this verification system is that this system can verify seal imprints of various qualities efficiently and accurately. Computer experiments with real seal imprints were performed by using this system, previous system (without image quality assessment function) and document examiners of a bank. The results of these experiments show that this system is superior in the verification performance to our previous system, and has a similar verification performance to that of document examiners (i.e., the experimental results show the effectiveness of adding the image quality assessment function to a seal imprint verification system).

In this paper, symbols and numerals in topographic maps are recognized by the multi-angled parallelism (MAP) matching method, and small dots and lines are extracted by the MAP operation method. These results are then combined to determine the value, position, and attributes of elevation marks. Also, we reconstruct three dimensional surfaces described by contours, which is difficult even for humans since the elevation symbols are sparse. In reconstruction of the surface, we define an energy function that enfores three constraints: smoothness, fit, and contour. This energy function is minimized by solving a large linear system of simultaneous equations. We describe experiments on 25,000:1 scale topographic maps of the Tsukuba area.