This paper describes a simple, inexpensive technique for intentionally broadening and flattening the spectrum of a DC-DC converter (switching regulator) to reduce Electro-Magnetic Interference (EMI). This noise spectrum broadening technique involves intentionally introducing pseudo-random dithering of control clock timing, which can be achieved by adding simple digital circuitry. This technique can significantly reduce noise power spectrum peaks at the DC-DC converter output. For our test case circuit, measurements showed that noise power was reduced by 5.7 dBm at the main peak, by 15.6 dBm at the second peak and by 12.8 dBm at the third peak. This simple, inexpensive technique can be applied to most conventional switching regulators by adding simple digital circuitry, and without any modification of the design of other parts.

We propose a new multiple access communication system based on finite field wavelet spread signature (FFWSS). In addition to the function of frequency diversity and multiple access, which are typically provided by traditional spreading codes, the FFWSS spreads data symbols in time, resulting in robustness against frequency selective slow fading. Using the FFWSS to spread a data symbol so that it is overlapped with neighboring symbols, a FFWSS-CDMA system is developed. It is observed that the ratio of the maximum nontrivial value of periodic correlation function to the code length of FFWSS is the same as that of a Sidelnikov sequence. Using RAKE-based receivers, simulation results show that the proposed FFWSS-CDMA system yields lower bit error rate (BER) than conventional DS-CDMA and MT-CDMA systems in multipath fading channels.

Many types of adaptive algorithms based on the MMSE criterion for co-channel interference suppression in DS/CDMA systems have been studied in great detail. However, these algorithms have such a problem that the training speed is greatly dropped under the strong near-far problem. In this paper, we propose and analyze an adaptive filter based on the Maximum Signal to Interference and Noise Ratio (MSINR) criterion, called adaptive MSINR filter. This filter is basically equivalent to the adaptive filter based on the MMSE criterion. However, due to the structual difference, the convergence speed is greatly improved. Specifically, the de-spreading vector in this filter is so renewed as to maximize the Signal to Interference and Noise Ratio (SINR) by minimizing the de-spread interference and noise power under the condition that the de-spread desired signal power keeps constant. So the proposed filter uses the estimated interference and noise signal calculated by subtracting the estimated desired signal from the received signal. It is just the reason why the adaptive MSINR filter shows remarkable convergence speed. And to satisfy the constant signal power condition, the projection matrix onto the orthogonal complement of the desired signal space is used for the de-spreading vector. For the proposed filter, we analyze the convergence modes and also investigate the de-spread interfernce and noise power for calculating the theoretical SINR curve. Then, we conduct some computer simulations in order to show the difference between this filter and the conventional one in terms of the SINR convergence speed. As the result, we confirm that the adaptive filter based on the MSINR criterion achieves significant progress in terms of the SINR convergence speed.

In wireless communication systems, low-power metrics is becoming a burdensome problem in the portable terminal design, because of portability constraints. This paper presents design architecture of a low-power Digital Matched Filter (DMF) for the direct-sequence spread-spectrum communication system such as WCDMA or wireless LAN. The proposed approach for power savings focuses on the architecture of the reception registers and the correlation-calculating unit, which dissipate the majority of the power in a DMF. The main features are asynchronous latch clock generation for the reception registers, parallelism of correlation calculation operations and bit manipulation for chip-correlation operations. A DMF is designed in compliance with the WCDMA specifications incorporating the proposed techniques, and its properties are evaluated by computer simulations at the gate level using 0.18-µm CMOS standard cell array technology. As a result, the power consumption of the proposed DMF is estimated to be 9.3 mW (@15.6 MHz, 1.6 V), which is below 40% of the power consumed by a general DMF.

This paper proposes Variable Spreading Factor-Orthogonal Frequency and Code Division Multiplexing (VSF-OFCDM) as the most promising forward link wireless access method in broadband packet wireless transmission using an approximate 50 to 100 MHz bandwidth. The proposed OFCDM employing VSF can flexibly realize near optimum wireless access satisfying higher radio link capacity both in isolated cell environments such as hot-spot areas and indoor offices and in multi-cell environments such as cellular systems by adaptively changing the appropriate spreading factor, SF, in the frequency domain based on the cell structure, radio link conditions such as the delay spread, and major radio link parameters such as the data modulation scheme and channel coding rate. Furthermore, by establishing SF=1, i.e., no spreading mode, VSF-OFCDM can be used as orthogonal frequency division multiplexing (OFDM). Computer simulation results demonstrate that, while SF=1 (OFDM) achieves higher link capacity than SF>1 in an isolated-cell environment, OFCDM with the optimized SF value over 1 achieves approximately 1.4 times higher capacity compared with OFDM in a multi-cell environment associated with the advantageous one-cell frequency reuse. Consequently, VSF-OFCDM can provide seamless deployment of broadband packet wireless access with higher radio link capacity, that is, OFDM in an isolated-cell environment, and OFCDM with the adaptively optimized SF value over 1 in a multi-cell environment according to the major radio link conditions and radio link parameters, by only changing the spreading factor.

This paper discusses two types of polyphase sequence sets, which will successfully provide CDMA systems without co-channel interference. One is a type of ZCZ sets, whose periodic auto-correlation functions take zero at continuous shifts on both side of the zero-shift, and periodic cross-ones also take zero at the continuous shifts and the zero-shift. The other is a new type of sets consisting of some subsets of polyphase sequences with zero cross-correlation zone, called ZCCZ sets, whose periodic cross-correlation functions among different subsets have take zero at continuous shifts on both side of the zero-shift including the zero-shift. The former can achieve a mathematical bound, and the latter can have large size.

Array antennas are employed at the receiver for a variety of purposes such as to combat fading or to reduce co-channel interference. To evaluate the performance of a wireless communications system using antenna arrays it becomes necessary to have spatial channel models that describe the Angle of Arrival (AOA), Time of Arrival (TOA) and the Angle Spread (AS) of the multipath components. Among the most widely used radio propagation models is the single bounce scattering geometric model, where propagation between the transmitting and receiving antennas is assumed to take place via single scattering from an intervening obstacle. Currently, several geometric models are available such as circular and elliptical scattering models, with each model being applicable to a specific environment type. This paper addresses the modeling, simulation and evaluation of the angle spread in smart antenna systems taking into account the Gaussian density model, and proves that the model finds use both in a micro cell as well as in a macro cell environment. Moreover, we show statistics for the angle and time of arrival.

In this paper, we propose and describe a new synchronizer for the FFT timing applicable to multi-carrier spread-spectrum (MC-SS) communication systems. The performance of the synchronizer is evaluated in terms of false- and miss-detection probabilities in the presence of additive white Gaussian noise (AWGN) and Rayleigh fading.

This paper investigates the impact of inter-carrier interference (ICI) due to Doppler spread on the packet error rate (PER) performance in Orthogonal Frequency and Code Division Multiplexing (OFCDM) packet wireless access employing turbo coding in a multipath fading channel, and describes the optimization of the sub-carrier spacing, Δ f, i.e., the number of sub-carriers, Nc, with an approximate 50-100 MHz bandwidth. Simulation results show that although the uncoded OFCDM in a 1-path flat Rayleigh fading channel is affected by the ICI caused by the Doppler spread when the maximum Doppler frequency, fD, becomes more than 5% of Δ f, OFCDM employing turbo coding in a 24-path Rayleigh fading channel is robust against Doppler spread and the degradation is not apparent until fD reaches more than 10% of Δ f. This is because the turbo coding gain and the frequency diversity effect compensate for the degradation due to ICI. Meanwhile, the PER performance with a larger Nc is degraded, since the effect of the error correction capability becomes smaller due to the larger variance of the despread OFCDM symbols associated with the narrower spreading bandwidth in the frequency domain. Consequently, along with the packet frame efficiency for accommodating the guard interval to compensate for the maximum multipath delay time of 1 µsec, we clarify that the optimum number of sub-carriers is approximately 512-1024 (the corresponding Δ f becomes 156.3-78.1 kHz) for broadband OFCDM packet wireless access assuming a 50-100 MHz bandwidth.

An adaptive modulated orthogonal frequency division multiplexing (OFDM) radio transmission scheme that enables efficient data transmission in multipath fading environments is newly proposed. This scheme can be used in standardized multimedia mobile access systems such as ETSI-BRAN, and ARIB-MMAC. It is based on estimating the delay spread and the carrier-to-noise power density ratio (C/N0). The estimation is done using channel estimation symbols that are inserted into the frames of the standard OFDM radio transmission scheme. Computer simulations show that the estimation method results in an average BER close to those when propagation characteristics are perfectly estimated. Furthermore, when the adaptive OFDM transmission scheme is based on BPSK, QPSK or 16 QAM, the average BER is almost close to that when BPSK-OFDM is only used, and the average transmission rate is 1.8 times as high. Using an error-correction code based on convolutional code results in an average BER lower than that with the BPSK- and QPSK-OFDM schemes.

The UCHT (Unified Complex Hadamard Transform) has been proposed as a new family of spreading sequences for DS-SSMA systems recently. In this Letter, the periodic autocorrelation (PAC) properties of the Unified Complex Hadamard Transform (UCHT) sequences are analyzed. Upper bounds for the out-of-phase PAC are derived for two groups of the UCHT sequences, namely the HSP-UCHT and the NHSP-UCHT sequences (the later is a more general representation of the well-known Walsh-Hadamard (WH) sequences). A comparison of the two bounds is performed. It turns out that the HSP-UCHT sequences have a lower upper bound for the out-of-phase PAC. This makes the HSP-UCHT sequences more effective than the WH sequences in combating multipath effect for DS-SSMA systems.

A performance comparison is developed between a chaotic communication system and a spread spectrum system with similar features in terms of bandwidth and transceiver structure but based on more conventional Gold sequences. Comparison is made in the presence of noise and multipath contributions which degrade the channel quality. It is shown that, because of its more favourable correlation properties, the chaotic scheme exhibits lower error rates, at a parity of the bandwidth expansion factor. The same favourable correlation properties are also used to explain and show, through a numerical example, the benefits of chaotic segments in a multi-user environment.

This paper proposes a multipath interference canceller (MPIC) for orthogonal code multiplexed channels in the W-CDMA forward link and evaluates by computer simulation the improvement in BER performance owing to the multipath interference (MPI) suppression effect obtained by the MPIC. The simulation results show that a one-stage MPIC, which removes the MPI from the common pilot channel (PICH), common control channel (CCH), and synchronization channel (SCH), achieves a sufficient MPI suppression effect, and that the required received Eb/N0 of the traffic channel (TCH) at the average BER of 10-3 using the MPIC for the common channels is decreased by approximately 6.5 dB compared to that with a matched filter (MF)-based Rake receiver (the transmit power ratio of each common channel to TCH: ΔPICH/TCH=0 dB, ΔCCH/TCH=5 dB, ΔSCH/TCH=3 dB, without fast transmit power control (TPC) and antenna diversity reception). We also show that by using MPIC, the required transmit Eb/N0 at the average BER of 10-3, when the ratio of the target Eb/I0 of the 9-interfering users to desired user is ΔInt/Des=6 dB with fast TPC, is increased by only approximately 0.6 dB compared to that when ΔInt/Des=0 dB. This implies that the preferential MPI suppression from high-rate TCHs that abates the increase in complexity in a mobile terminal is effective in increasing the link capacity in the forward link.

Compared with much research in the spatial-domain and transform-domain watermarking techniques, VQ-based watermarking technique has not been fully treated. A digital image watermarking scheme based on vector quantisation (VQ) is proposed to improve the degree of spreading watermark information. By partitioning the codebook into 3 groups, the scheme tries to embed one binary information for each block. The scheme spreads the watermark information almost evenly over the image with little extra distortion. The experimental results prove the efficiency and effectiveness of the scheme.

In this paper, we present a new approach to the construction of a set of binary sequences with a zero-correlation zone. The set consists of n pairs of binary sequences and the length of each binary sequence is n2(m+2) for some integers m and n. The Hadamard sequences with length n are used to construct the set. Any sequence in the set has 2(m+1) subsequences, each of length 2n. The author proves that any two subsequences are orthogonal if they belong to different pairs of binary sequences in the set.

Nonlinear feedback shift registers (NFSRs), which can generate maximal-period sequences called de Bruijn sequences, are regarded as one-dimensional maps with finite bits by observing states of the registers at each time. Such one-dimensional maps are similar to the Bernoulli map which is a famous chaotic map. This implies that an NFSR is one of finite-word-length approximations to the Bernoulli map. Inversely, constructing such one-dimensional maps with finite bits based on other chaotic maps, we can design new types of NFSRs, called extended NFSRs, which can generate new maximal-period sequences. We design such extended NFSRs based on some well-known chaotic maps, which gives a new concept in sequence design. Some properties of maximal-period sequences generated by such NFSRs are investigated and discussed.

It is known that MUSIC and ESPRIT algorithms can estimate simultaneously both the instantaneous Direction of Arrival (DOA) and the instantaneous Angular Spread (AS) in multiple scattering environments. These algorithms use the Extended Array Mode Vector (EAMV) with complex angle. The previous work evaluated the performance of those algorithms by comparing the estimated DOA and the estimated AS with the DOA and the AS given in the EAMV, which uses the first-order approximation. Thus, this evaluation method has not clearly reflected the estimation accuracy of MUSIC and ESPRIT. This paper presents the joint estimation performance of MUSIC and ESPRIT by introducing the criteria for evaluation. For this, the spatial signature (SS) is reconstructed from the estimates of the DOA and the AS, and compared to the true SS in the meaning of data fitting.

The possibility of applying a recently proposed emission source location method, which is based on CISPR measurements, to sources with arbitrary directional current components is studied. We propose a new finding algorithm in which the horizontal and the vertical current components are estimated at the same time by taking into account the contribution of horizontal current components when calculating the vertical electric field. As a result of experimental verification by using two spherical dipole antennas as ideal emission sources, estimated values show good agreement with the original ones in the frequency range from 300 MHz to 1 GHz, where the position estimation deviation d was less than 0.15 m, the amplitude estimation deviation j was less than 2.1 dB, and furthermore the angle of current direction could be estimated. Consequently, this method with the presented new algorithm can be applied to find radiated emission sources even when the current components point to arbitrary directions.

We have designed the Half Adder (HA) circuit and the Carry Save Serial Adder (CSSA) circuit based on pipeline architecture. Our HA has the structure of a two-stage pipeline and consists of 160 Josephson Junctions (JJs). Our CSSA has the structure of a four-stage pipeline with a feedback loop and consists of 360 JJs. These circuits were fabricated by the NEC standard process. There are two issues which should be considered in the design. One is parameter spreads generated by the fabrication process and the other is leakage currents between the gates. We have introduced a parameter optimization method to deal with the parameter spreads. We have also inserted three stages of JTLs to reduce leakage currents. We have experimentally confirmed the correct operations of these circuits. The obtained bias margins were 33.1% for the HA and 24.6% for the CSSA.

A rapid Pseudo-Noise (PN) acquisition scheme is proposed. The proposed scheme consists of a phase alignment detector and Voltage Controlled Clock (VCC) loop. The VCC loop is used to control the phase update of the local PN signal. It has an auxiliary signal that provides the loop with two stable locking points as well as the direction of each phase update. The performance of the proposed scheme is evaluated by simulation. Results show that the proposed scheme acquires the phase two to three times faster than the conventional coherent serial scheme, and 1.5 times faster than of that in [10], at a small amount of additional hardware.