In our previous paper, we presented a concept of “Baseband Radio” as an ideal of future wireless communication scheme. Furthermore, for enhancing the adaptability of baseband radio, the adaptive baseband radio was discussed as the ultimate communication system; it integrates the functions of cognitive radio and software-defined radio. In this paper, two transmission schemes that take advantage of adaptive baseband radio are introduced and the results of a performance evaluation are presented. The first one is a scheme based on DSFBC for realizing higher reliability; it allows the flexible use of frequency bands over a wide range of white space. The second one is a low-power-density communication scheme with spectrum-spreading by means of frequency-domain differential coding so that the secondary system does not seriously interfere with primary-user systems that have been assigned the same frequency band.

Based upon the Kerckhoffs' principle, illegal users can get to know the embedding and detection algorithms except for a secret key. Then, it is possible to access to a host signal which may be selected from frequency components of a digital content for embedding watermark signal. Especially for a fingerprinting scheme which embeds user's information as a watermark, the selected components can be easily found by the observation of differently watermarked copies of a same content. In this scenario, it is reported that some non-linear collusion attacks will be able to remove/modify the embedded signal. In this paper, we study the security analysis of our previously proposed spread-spectrum (SS) fingerprinting scheme[1], [2] under the Kerckhoffs' principle, and reveal its drawback when an SS sequence is embedded in a color image. If non-linear collusion attacks are performed only to the components selected for embedding, the traceability is greatly degraded while the pirated copy keeps high quality after the attacks. We also propose a simple countermeasure to enhance the robustness against non-linear collusion attacks as well as possible signal processing attacks for the underlying watermarking method.

This paper proposes a novel direction-of-arrival (DOA) estimation method that can reduce performance degradation due to angular spread. Some algorithms previously proposed for such estimation make assumptions about the distributions of amplitude and phase for incident waves because most DOA estimation algorithms are sensitive to angular spread. However, when the assumptions are inaccurate, these algorithms perform poorly as compared with algorithms without countermeasures against angular spread. In this paper, we propose a method for selecting an appropriate DOA estimation algorithm according to the channel vector of each source signal as estimated by independent component analysis. Computer simulations show that the proposed method can robustly estimate DOA in environments with angular spread.

Point spread function (PSF) estimation plays a paramount role in image deblurring processing, and traditionally it is solved by parameter estimation of a certain preassumed PSF shape model. In real life, the PSF shape is generally arbitrary and complicated, and thus it is assumed in this manuscript that a PSF may be decomposed as a weighted sum of a certain number of Gaussian kernels, with weight coefficients estimated in an alternating manner, and an l1 norm-based total variation (TVl1) algorithm is adopted to recover the latent image. Experiments show that the proposed method can achieve satisfactory performance on synthetic and realistic blurred images.

We propose a method of spread spectrum digital watermarking with quantization index modulation (QIM) and evaluate the method on the basis of IHC evaluation criteria. The spread spectrum technique can make watermarks robust by using spread codes. Since watermarks can have redundancy, messages can be decoded from a degraded stego-image. Under IHC evaluation criteria, it is necessary to decode the messages without the original image. To do so, we propose a method in which watermarks are generated by using the spread spectrum technique and are embedded by QIM. QIM is an embedding method that can decode without an original image. The IHC evaluation criteria include JPEG compression and cropping as attacks. JPEG compression is lossy compression. Therefore, errors occur in watermarks. Since watermarks in stego-images are out of synchronization due to cropping, the position of embedded watermarks may be unclear. Detecting this position is needed while decoding. Therefore, both error correction and synchronization are required for digital watermarking methods. As countermeasures against cropping, the original image is divided into segments to embed watermarks. Moreover, each segment is divided into 8×8 pixel blocks. A watermark is embedded into a DCT coefficient in a block by QIM. To synchronize in decoding, the proposed method uses the correlation between watermarks and spread codes. After synchronization, watermarks are extracted by QIM, and then, messages are estimated from the watermarks. The proposed method was evaluated on the basis of the IHC evaluation criteria. The PSNR had to be higher than 30 dB. Ten 1920×1080 rectangular regions were cropped from each stego-image, and 200-bit messages were decoded from these regions. Their BERs were calculated to assess the tolerance. As a result, the BERs were less than 1.0%, and the average PSNR was 46.70 dB. Therefore, our method achieved a high image quality when using the IHC evaluation criteria. In addition, the proposed method was also evaluated by using StirMark 4.0. As a result, we found that our method has robustness for not only JPEG compression and cropping but also additional noise and Gaussian filtering. Moreover, the method has an advantage in that detection time is small since the synchronization is processed in 8×8 pixel blocks.

In this paper, a new parameter estimator for coherently distributed (CD) noncircular (NC) signals is proposed, and can estimate both the central direction-of-arrivals (DOAs) and the angular spreads. It can also be considered as an extended version of the generalized Capon method by using both covariance matrix and an elliptic covariance matrix. The central DOAs and angular spreads are obtained by two-dimensional spectrum-peak searching. Numerical examples illustrate that the proposed method can estimate the central DOAs and the angular spreads when the number of signals is greater than the number of sensors. The proposed method also offers better performance than the methods against which it is compared.

Measurements of 60GHz proximity channels are performed in desktop environments with a digital camera, a laptop PC, a tablet, a smartphone, and a DVD player. The results are characterized by a statistical channel model. All measured channels are found to be similar to conventional exponential decay profiles that have a relatively large first path due to line-of-sight components. We also show that the power difference between the first path and the delay paths is related to randomization of radio wave polarization by internal reflections in the devices, whereas this is conventionally dependent on only a Rice factor. To express this effect, the conventional model is modified by adding one parameter. Computer simulations confirm that RMS delay spreads of the modeled channels are a good fit to measured channels under most conditions.

A serial ATA PHY fabricated in a 0.15-µm CMOS process performs the serial ATA operation in an asynchronous transition by using large variation in the reference clock. This technique calibrates a transmission signal frequency by utilizing the received signal. This is achieved by calibrating the divide ratio of a spread-spectrum clock generator (SSCG). This technique enables a serial ATA PHY to use reference oscillators with a production-frequency tolerance of less than 400ppm, i.e., higher than the permissible TX frequency variations (i.e., 350ppm). The calibrated transmission signal achieved a total jitter of 3.9ps.

Step-edge vertical channel organic field-effect transistors (SVC-OFETs) with a very short channel have been fabricated by a novel selective electrospray deposition (SESD) method. We propose the SESD method for the fabrication of SVC-OFETs based on a 6,13-bis(triisopropyl-silylethynyl) pentacene (TIPS-pentacene) semiconductor layer formed by SESD. In the SESD method, an electric field is applied between the nozzle and selective patterned electrodes on a substrate. We demonstrated that the solution accumulates on the selected electrode pattern by controlling the voltage applied to the electrode.

This study proposes a novel method for evaluating the transmission characteristics of a three-phase filter using the “Fortescue-mode S-parameters,” which are S-parameters whose variables are transformed into symmetrical coordinates (i.e., zero-/positive-/negative-phase sequences). The behavior of the filter under three-phase current, including its non-symmetry, can be represented by these S-parameters, without regard to frequency. This paper also describes a methodology for creating modal equivalent circuits that reflect Fortescue-mode S-parameters allowing the effects of circuit components on filter characteristics to be estimated. Thus, this method is useful not only for the measurement and evaluation but also for the analysis and design of a three-phase filter. In addition, the physical interpretation of asymmetrical/symmetrical insertion losses and the conversion method based on Fortescue-mode S-parameters are clarified.

We construct two types of reverberation chambers, one is 4(m) × 2(m) × 2(m)-sized and the other is 2(m) × 2(m) × 2(m)-sized for realizing a multipath-rich environment for MIMO-OTA measurements. In this paper, we measure fundamental propagation characteristics, including amplitude statistics, multipath-delay statistics, spatial correlation characteristics, and cross polarization characteristics over a frequency range of 800MHz to 5GHz in our reverberation chamber. Also, we confirm the existence of spatially uniform area of 1m2 area, which might be sufficiently large to set a device under test (DUT) in the chamber. Theoretical considerations about the characteristics are also given to support the design of reverberation chamber.

The volumetric representations of deformable objects suffer from high memory and computational costs. In this work we analyze an approach of constructing low-resolution mass spring models (MSMs) on the basis of a high-resolution reference MSM. Preserving the physical properties of the modeled objects is emphasized such that their motion is consistent and independent of the spring network resolution. We varied the node merging algorithm and analyzed how various aspects of the simplification process affected the properties of the model and how these properties translated into visual behavior in a simulation.

An echo-hiding scheme is presented to detect the pitch variation due to playback speed modification. The inserted time-spread echo is obtained by convolving the highpass filtered audio with a gain-controlled pseudo noise sequence. The perceptual evaluation confirms that the embedded echo is virtually imperceptible. Compared with the Fourier magnitude modulation, the proposed scheme attains better detection rates.

A maximum-likelihood code acquisition scheme is investigated for frequency-selective fading channels with an emphasis on the decision strategies. Using the maximum-likelihood estimation technique, we first derive an optimal decision rule, which is optimal in the viewpoint of probability of detection. Based on the derived optimal decision rule, a practical and simple decision rule is also developed, and its performance is assessed for both single dwell and double dwell acquisition systems. Simulation results demonstrate that the proposed acquisition scheme significantly outperforms the previously proposed schemes in frequency-selective fading channels.

The present paper proposes two new methods for constructing polyphase asymmetric zero-correlation zone (A-ZCZ) sequence sets. In previous studies, the authors proposed methods for constructing quasi-optimal polyphase A-ZCZ sequence sets using perfect sequences and for constructing optimal polyphase A-ZCZ sequence sets using discrete Fourier transform (DFT) matrices. However, in these methods, the total number of sequences in an A-ZCZ sequence set cannot exceed the period of the perfect sequence or the dimension of the DFT matrix used for constructing the A-ZCZ sequence set. We now propose two extended versions of these methods. The proposed methods can generate a quasi-optimal or optimal polyphase A-ZCZ sequence set where the total number of sequences exceeds the period of the perfect sequence or the dimension of the DFT matrix. In other words, the proposed methods can generate new A-ZCZ sequence sets that cannot be obtained from the known methods.

Genetic algorithm (GA) is now an important tool in the field of wireless communications. For multiple-input/multiple-output (MIMO) wireless communications system employing spatial multiplexing transmission, we evaluate the effects of GA parameters value on channel parameters in fading channels. We assume transmit-correlated Rayleigh and Rician fading with realistic Laplacian power azimuth spectrum. Azimuth spread (AS) and Rician K-factor are selected according to the measurement-based WINNER II channel model for several scenarios. Herein we have shown the effects of GA parameters and channel parameters in different WINNER II scenarios (i.e., AS and K values) and rank of the deterministic components. We employ meta GA that suitably selects the population (P), generation (G) and mutation probability (pm) for the inner GA. Then we show the cumulative distribution function (CDF) obtain experimentally for the condition number C of the channel matrix H. It is found that, GA parameters depend on the channel parameters, i.e., GA parameters are the functions of the channel parameters. It is also found that for the poorer channel conditions smaller GA parameter values are required for MIMO detection. This approach will help to achieve maximum performance in practical condition for the lower numerical complexity.

The reliability of a connector depends on the contact force generated by the spring in the terminal of a connector. The springs are commonly formed by stamping from a strip of spring material. Therefore, the prediction of the force — displacement relation by the finite element (FE) method is very important for the design of terminals. For simulation, an accurate model of stress-strain (s-s) responses of the materials is required. When the materials are deformed in the forward and then the reverse directions, almost all spring materials show different s-s responses between the two directions, due to the Bauschinger effect. This phenomenon makes simulation difficult because the s-s response depends on the prior deformation of the material. Hence, the measurement of the s-s response is the elementary process, by cyclic tension and compression testing in which materials deform elastically and plastically. Then, the s-s responses should be described accurately by mathematical models for FE simulation. In this paper, the authors compare the experimental s-s responses of copper-based materials with conventional mathematical models and the Yoshida-Uemori model, which is a constitutive model having high capability of describing the elastic and plastic behavior of cyclic deformation. The calculated s-s responses only by Yoshida-Uemori model were in very good agreement with the corresponding experimental results. Therefore, the use of this model for FE simulation would be recommended for a more accurate prediction of force-displacement relation of the spring.

This paper proposes the use of on-chip monitor circuits to detect process shift and process spread for post-silicon diagnosis and model-hardware correlation. The amounts of shift and spread allow test engineers to decide the correct test strategy. Monitor structures suitable for detection of process shift and process spread are discussed. Test chips targeting a nominal process corner as well as 4 other corners of “slow-slow”, “fast-fast”, “slow-fast” and “fast-slow” are fabricated in a 65nm process. The monitor structures correctly detects the location of each chip in the process space. The outputs of the monitor structures are further analyzed and decomposed into the process variations in threshold voltage and gate length for model-hardware correlation. Path delay predictions match closely with the silicon values using the extracted parameter shifts. On-chip monitors capable of detecting process shift and process spread are helpful for performance prediction of digital and analog circuits, adaptive delay testing and post-silicon statistical analysis.

A technique that enables a SSCG to fine-tune an output signal frequency and a spread ratio is presented. Proposed SSCG achieves the output signal frequency from 1.2 GHz to 3.0 GHz and the spread ratio from 0 to 30000 ppm. The fine-tuning technique achieves 30 ppm adjustment of the output signal frequency and 200 ppm adjustment of the spread ratio. This technique is achieved by controlling a triangular modulation signal characteristics generated by a proposed digital controlled wave generator. A proposed multi-modulus divider can have a divide ratio of 4/5 and 8/9. This SSCG has been fabricated in a 0.13-µm CMOS process. The output signal frequency-range and the spread ratio are achieved fluently from 0.1 to 3.0 GHz and from 0 to 30000 ppm, respectively. EMI noise is suppressed at less than 17.1 dB at the output signal frequency of 3.0 GHz and spread ratio of 30000 ppm.

In order to evaluate the goodness of frequency hopping (FH) sequence design, the periodic Hamming correlation function is used as an important measure. But aperiodic Hamming correlation of FH sequences matters in real applications, while it received little attraction in the literature compared with periodic Hamming correlation. In this paper, the new aperiodic Hamming correlation lower bounds for FH sequences, with respect to the size of the frequency slot set, the sequence length, the family size, the maximum aperiodic Hamming autocorrelation and the maximum aperiodic Hamming crosscorrelation are established. The new aperiodic bounds are tighter than the Peng-Fan bounds. In addition, the new bounds include the second powers of the maximum aperiodic Hamming autocorrelation and the maximum aperiodic Hamming crosscorrelation but the Peng-Fan bounds do not include them. For the given sequence length, the family size and the frequency slot set size, the values of the maximum aperiodic Hamming autocorrelation and the maximum aperiodic Hamming crosscorrelation are inside of an ellipse which is given by the new aperiodic bounds.