The purpose of this paper is to propose an efficient and effective design scheme to implement compact, high-performance wideband bandpass filters based on a novel compound three-line unit consisting of a stub-loaded short-circuited parallel-coupled three-line structure and two lead lines. Firstly, a simulative investigation is conducted on the transmission characteristics of the proposed coupling unit. The results show that the bandwidth of such structure can be predicted by a symmetric parallel-coupled short-circuited three-line unit, whereas the transmission zeros by a three-section stub composed of the loaded stub, one of the parallel-coupled three lines and the lead line. Accordingly, given specifications, a pseudo-elliptical filter can be designed in an novel three-coupled-line based two-step design scheme: 1. after the derivation of the new closed-form synthesis formulae, a Chebyshev ultra-wideband (UWB) filter is synthesized on a desired passband using symmetric three-line coupling units. 2. By designing the stubs and choosing the proper lengths of the lead lines, multiple transmission zeros are then introduced to improve the skirt and stopband characteristics, whereas the equiripple characteristics are kept in passband. As an example, a UWB bandpass filter covering the Japan's lower UWB band (BW: 3.1-4.8 GHz, FBW: 43%) is designed to describe the proposed design procedure. The measured filtering characteristics agree very well with the theoretical predictions, which validate the effectiveness of the proposed new coupling structure and corresponding filter design technique. In addition, the designed filters exhibit good characteristics, such as steep skirt selectivity, very wide stopbands, a compact size compared with the filter based on short-circuited three-line structure, etc.

In this paper, the 8th harmonic Push-Push oscillator is successfully presented. The Push-Push principle and the excellent harmonic coherency in a microwave resonator are effectively utilized. The proposed oscillator consists of two sub-circuits, a microstrip ring resonator and an output circuit. The concept of the simplified structure harmonic oscillator (SSHO) is adopted in the proposed oscillator. The microstrip ring resonator plays two roles of the common resonator and the power combiner circuit. This kind of Push-Push oscillator has practical advantages of the easy circuit design due to the simple circuit configuration and the miniaturization of the circuit size. Using the Push-Push principle and the effective circuit configuration of the output circuit, the desired 8th harmonic signal is effectively enhanced. This Push-Push oscillator achieves good millimeter-wave oscillation in V band using inexpensively available X band HEMTs. The estimated output power of -6 dBm at the frequency of 51 GHz is obtained with the phase noise of -93 dBc/Hz at the offset frequency of 1 MHz.

This paper presents a digital predistorter with a wideband memory effect compensator for a Doherty power amplifier (PA). A simple memory-predistortion model, which consists of a look-up-table (LUT) and an adaptive filter equalizing memory effects, and a new memory effect estimation algorithm using a direct-learning architecture are proposed. The proposed estimation algorithm has an advantage that a transfer function of a feedback circuit does not affect the learning process. The predistorter is implemented in a field programmable gate array (FPGA) and a digital signal processor (DSP). The transmitter has achieved distortion level of -50.8 dBr at signal bandwidth away from the carrier, and PA module efficiency of 24% with output power of 43 dBm at 2595 MHz under a 20 MHz-bandwidth orthogonal frequency division multiplexing (OFDM) signal using laterally diffused metal oxide semiconductor (LDMOS) FETs.

In this paper, a novel CMA (constant modulus algorithm) algorithm employing fast convolution in the DFT (discrete Fourier transform) domain is proposed. We propose a non-linear adaptation algorithm that minimizes CMA cost function in the DFT domain. The proposed algorithm is completely new one as compared to the recently introduced similar DFT domain CMA algorithm in that, the original CMA cost function has not been changed to develop DFT domain algorithm, resulting improved convergence properties. Using the proposed approach, we can reduce the number of multiplications to O(Nlog2 N), whereas the conventional CMA has the computation order of O(N2). Simulation results show that the proposed algorithm provides a comparable performance to the conventional CMA.

In this paper, we present a new composite transistor circuit design technique that provides superior performance enhancement to analog circuits. By adding a composite transistor to the cascode-compensated amplifier, it has achieved a 102 dB DC gain, and a 37.6 MHz unity gain bandwidth while driving a 2 nF heavy capacitive load at a single 1.8 V supply. In the comparison of power-bandwidth and power-speed efficiencies on figures of merit, it offers significantly high values with respect to the reported state-of-the-art works. By employing the composite transistor in a linear regulator powered by a 3.3 V supply to generate a 1.8 V output voltage, it has shown fast recovery response at various load current transients, having a 1% settling time of 0.1 µS for a 50 mA or 100 mA step, while a 1% settling time of 0.36 µS for a maximum 735 mA step under a capacitive load of 10 µF with a 1 Ω ESR resistor. The simulated load regulation is 0.035% and line regulation is 0.488%. Comparing its results with other state-of-art LDO reported results, it also validates the significant enhanced performance of the proposed composite-transistor-based design in terms of speed, current driving capability and stability against changes in environmental parameters. All the proposed designs are simulated using chartered semiconductor (CSM) 1.8 V/3.3 V 0.18 µm CMOS triple-well process technology with thin/thick oxide options and BSIM3 model parameters.

A novel broad-band ring-slot array antenna for simultaneous use of orthogonal polarizations is presented in this paper. In this antenna, the broad-band performance is obtained by integrating a 22 ring-slot array antenna and a broad-band π/2 hybrid circuit. The simultaneous use of the right-hand circular polarization (RHCP) and the left-hand circular polarization (LHCP) is achieved using orthogonal feed circuits on three layers. The both-sided MIC technology is effectively employed in forming this type of slot array antenna. Experimental results show that the proposed antenna has good circular polarization characteristics for both the LHCP and the RHCP. The measured impedance-bandwidth of return loss better than -10 dB are about 47% both for the LHCP and the RHCP. The 3 dB axial ratio bandwidths are 25% (RHCP) and 29% (LHCP). The isolation between the two input ports is better than -35 dB at center frequency of 7.5 GHz.

Broadband optical access services are spreading throughout the world, and the number of fiber to the home (FTTH) subscribers is increasing rapidly. Telecom operators are constructing passive optical networks (PONs) to provide optical access services. Externally installed optical splitters for PONs are very important passive devices in optical access networks, and they must provide satisfactory performance as outdoor plant over long periods. Therefore, we calculate the failure rate of optical access networks and assign a failure rate to the optical splitters in optical access networks. The maximum cumulative failure rate of 18 optical splitters was calculated as 0.025 for an optical access fiber length of 2.1 km and a 20-year operating lifetime. We examined planar lightwave circuit (PLC) type optical splitters for use as outside plant in terms of their optical characteristics and environmental reliability. We confirmed that PLC type optical splitters have sufficient optical performance for a PON splitter and sufficient reliability as outside plant in accordance with ITU-T standard values. We estimated the lifetimes of three kinds of PLC type optical splitters by using accelerated aging tests. The estimated failure rate of these splitters installed in optical access networks was below the target value for the cumulative failure rate, and we confirmed that they have sufficient reliability to maintain the quality of the network service. We developed 18 optical splitter modules with plug and socket type optical connectors and optical fiber cords for optical aerial closures designed for use as outside plant. These technologies make it easy to install optical splitters in an aerial optical closure. The optical splitter modules have sufficient optical performance levels for PONs because the insertion loss at the commercially used wavelengths of 1.31 and 1.55 µm is less than the criterion established by ITU-T Recommendation G.671 for optical splitters. We performed a temperature cycling test, and a low temperature storage and damp heat test to confirm the long-term reliability of these modules. They exhibited sufficient reliability as regards heat and moisture because the maximum loss change was less than 0.3 dB.

This paper presents Probabilistic Bi-polar Radial Reach Correlation (PrBPRRC), a change detection method that is robust against illumination changes and background movements. Most of the traditional change detection methods are robust against either illumination changes or background movements; BPRRC is one of the illumination-robust change detection methods. We introduce a probabilistic background texture model into BPRRC and add the robustness against background movements including foreground invasions such as moving cars, walking people, swaying trees, and falling snow. We show the superiority of PrBPRRC in the environment with illumination changes and background movements by using three public datasets and one private dataset: ATON Highway data, Karlsruhe traffic sequence data, PETS 2007 data, and Walking-in-a-room data.

Multi-cell resource allocation under minimum rate request for each user in OFDMA networks is addressed in this paper. Based on Lagrange dual decomposition theory, the joint multi-cell resource allocation problem is decomposed and modeled as a limited-cooperative game, and a distributed multi-cell resource allocation algorithm is thus proposed. Analysis and simulation results show that, compared with non-cooperative iterative water-filling algorithm, the proposed algorithm can remarkably reduce the ICI level and improve overall system performances.

ICI (Inter-Cell Interference) mitigation schemes at the cell border are frequently dealt with as a special issue in 3GPP LTE (Long Term Evolution). However, few papers have analyzed the outage performance for the ICI mitigation schemes. In this paper, we propose a generalized cell planning scheme termed QBPA (Quality of Service based Band Power Allocation). Utilizing the QBPA scheme, we measure how much increase in channel capacity can be obtained through the flexible control of bandwidth and power in multi-cell forward-link environments. In addition, the feasible performance of the conventional schemes can be evaluated as long as those schemes are specific forms of the QBPA.

Generalized selection combining (GSC) was recently proposed as a low-complexity diversity combining technique for diversity-rich environments. This letter proposes a multi-hop Decode-and-Forward Relaying (MDFR) scheme in conjunction with GSC and describes its performance in terms of average bit error probability. We have shown that the proposed protocol offers a remarkable diversity advantage over direct transmission as well as the conventional decode-and-forward relaying (CDFR) scheme. Simulation results are also given to verify the analytical results.

Basic left hand mode transmission line (LH mode TL) characteristics made on PCB is an important future issue for the application of the EMC field. In this paper, possibility of a LH mode TL characteristic made by a folded-stepped impedance resonator (F-SIR) type is investigated experimentally and numerically. The experimental and calculated from FEM and equivalent circuit results indicate that some backward propagation characteristic and negative group delay can be established by F-SIR structure.

Numerical simulations of the gain and phase center measurements for a pyramidal horn antenna are carried out. The electromagnetic simulation is based on the finite integration method. The gain of horn antennas varies with the distance between their apertures, even if the antennas satisfy the far-field criterion. This gain variation is shown to correspond with the ratio of the distance between the apertures to the distance between the phase centers. The experimental results also demonstrate the efficacy of considering the location of the phase center for antenna calibration.

We investigate connected proper interval graphs without vertex labels. We first give the number of connected proper interval graphs of n vertices. Using this result, a simple algorithm that generates a connected proper interval graph uniformly at random up to isomorphism is presented. Finally an enumeration algorithm of connected proper interval graphs is proposed. The algorithm is based on reverse search, and it outputs each connected proper interval graph in (O)1 time.

This research addresses a high-speed computation method for the Kleene star of the weighted adjacency matrix in a max-plus algebraic system. We focus on systems whose precedence constraints are represented by a directed acyclic graph and implement it on a Cell Broadband EngineTM (CBE) processor. Since the resulting matrix gives the longest travel times between two adjacent nodes, it is often utilized in scheduling problem solvers for a class of discrete event systems. This research, in particular, attempts to achieve a speedup by using two approaches: parallelization and SIMDization (Single Instruction, Multiple Data), both of which can be accomplished by a CBE processor. The former refers to a parallel computation using multiple cores, while the latter is a method whereby multiple elements are computed by a single instruction. Using the implementation on a Sony PlayStation 3TM equipped with a CBE processor, we found that the SIMDization is effective regardless of the system's size and the number of processor cores used. We also found that the scalability of using multiple cores is remarkable especially for systems with a large number of nodes. In a numerical experiment where the number of nodes is 2000, we achieved a speedup of 20 times compared with the method without the above techniques.

This paper presents a high-speed, low-complexity VLSI architecture based on the modified Euclidean (ME) algorithm for Reed-Solomon decoders. The low-complexity feature of the proposed architecture is obtained by reformulating the error locator and error evaluator polynomials to remove redundant information in the ME algorithm proposed by Truong. This increases the hardware utilization of the processing elements used to solve the key equation and reduces hardware by 30.4%. The proposed architecture retains the high-speed feature of Truong's ME algorithm with a reduced latency, achieved by changing the initial settings of the design. Analytical results show that the proposed architecture has the smallest critical path delay, latency, and area-time complexity in comparison with similar studies. An example RS(255,239) decoder design, implemented using the TSMC 0.18 µm process, can reach a throughput rate of 3 Gbps at an operating frequency of 375 MHz and with a total gate count of 27,271.

10G-EPON systems have attracted a great deal of attention as a way of exceeding to realize over 10 Gb/s for optical subscriber networking. Rapid burst-mode transmitting/receiving techniques are the key technologies enabling the burst-mode upstream transmission of 10G-EPON systems. In this paper, we have developed a OLT burst-mode 3R receiver incorporating a burst-mode AGC optical receiver and an 82.5 GS/s over-sampling burst-mode CDR and a ONU burst-mode transmitter with high launch power DFB-LD of 1.27 µm wavelength to fully compliant with IEEE802.3av 10G-EPON PR30 standards. The transmitting characteristics of a fast LD turn-on/off time of less than 6ns and a high launch power of more than +8.0 dBm, and the receiving characteristics of receiver sensitivity of -30.1 dBm and the upstream power budget of 38.1 dB are successfully achieved.

The tiled-display system has been used as a Computer Supported Cooperative Work (CSCW) environment, in which multiple local (and/or remote) participants cooperate using some shared applications whose outputs are displayed on a large-scale and high-resolution tiled-display, which is controlled by a cluster of PC's, one PC per display. In order to make the collaboration effective, each remote participant should be aware of all CSCW activities on the titled display system in real-time. This paper presents a capturing and delivering mechanism of all activities on titled-display system to remote participants in real-time. In the proposed mechanism, the screen images of all PC's are periodically captured and delivered to the Merging Server that maintains separate buffers to store the captured images from the PCs. The mechanism selects one tile image from each buffer, merges the images to make a screen shot of the whole tiled-display, clips a Region of Interest (ROI), compresses and streams it to remote participants in real-time. A technical challenge in the proposed mechanism is how to select a set of tile images, one from each buffer, for merging so that the tile images displayed at the same time on the tiled-display can be properly merged together. This paper presents three selection algorithms; a sequential selection algorithm, a capturing time based algorithm, and a capturing time and visual consistency based algorithm. It also proposes a mechanism of providing several virtual cameras on tiled-display system to remote participants by concurrently clipping several different ROI's from the same merged tiled-display images, and delivering them after compressing with video encoders requested by the remote participants. By interactively changing and resizing his/her own ROI, a remote participant can check the activities on the tiled-display effectively. Experiments on a 32 tiled-display system show that the proposed merging algorithm can build a tiled-display image stream synchronously, and the ROI-based clipping and delivering mechanism can provide individual views on the tiled-display system to multiple remote participants in real-time.

The ability to find the speaker's face region in a video is useful for various applications. In this work, we develop a novel technique to find this region within different time windows, which is robust against the changes of view, scale, and background. The main thrust of our technique is to integrate audiovisual correlation analysis into a video segmentation framework. We analyze the audiovisual correlation locally by computing quadratic mutual information between our audiovisual features. The computation of quadratic mutual information is based on the probability density functions estimated by kernel density estimation with adaptive kernel bandwidth. The results of this audiovisual correlation analysis are incorporated into graph cut-based video segmentation to resolve a globally optimum extraction of the speaker's face region. The setting of any heuristic threshold in this segmentation is avoided by learning the correlation distributions of speaker and background by expectation maximization. Experimental results demonstrate that our method can detect the speaker's face region accurately and robustly for different views, scales, and backgrounds.

The singular points of fingerprints, viz. core and delta, are important referential points for the classification of fingerprints. Several conventional approaches such as the Poincare index method have been proposed; however, these approaches are not reliable with poor-quality fingerprints. This paper proposes a new core and delta detection employing singular candidate analysis and an extended relational graph. Singular candidate analysis allows the use both the local and global features of ridge direction patterns and realizes high tolerance to local image noise; this involves the extraction of locations where there is high probability of the existence of a singular point. Experimental results using the fingerprint image databases FVC2000 and FVC2002, which include several poor-quality images, show that the success rate of the proposed approach is 10% higher than that of the Poincare index method for singularity detection, although the average computation time is 15%-30% greater.