This paper condiders a problem of logecal configuration in reconfigurable VCDN (Virtual Circuit Data Networks) which is analyzed through a mimimax approach, and its objective is to minimize the largest delay on any logical link, measured in both queueing delay and propagation delay. The problem is formulated as a 0/1 mixed integer programming and analyzed by decomposing it into two subproblems, called routing and dimensioning problems, for which an efficient hauristic algorithm is proposed in an iterating process made beween the two subproblems for solution improvement. The algorithm is tested for its performance eveluation.

A novel method is presented for designing discrete coeffcient FIR linear phase filters using Hopfield neural networks. The proposed method is based on the minimization of the energy function of Hopfield neural networks. In the proposed method, the optimal solution for each filter gain factor is first searched for, then the optimal filter gain factor is selected. Therefore, a good solution in the specified criterion can be obtained. The feature of the proposed method is that it can be used to design FIR linear phase filters with different criterions simultaneously. A design example is presented to demonstrate The effectiveness of the proposed method.

This paper proposes an unsupervised speaker adaptation method using an all-phoneme ergodic Hidden Markov Network" that combines allophonic (context-dependent phone) acoustic models with stochastic language constraints. Hidden Markov Network (HMnet) for allophone modeling and allophonic bigram probabilities derived from a large text database are combined to yield a single large ergodic HMM which represents arbitrary speech signals in a particular language so that the model parameters can be re-estimated using text-unknown speech samples with the Baum-Welch algorithm. When combined with the Vector Field Smoothing (VFS) technique, unsupervised speaker adaptation can be effectively performed. This method experimentally gave better performances compared with our previous unsupervised adaptation method which used conventional phonetic HMMs and phoneme bigram probabilities especially when the amount of training data was small.

This paper presents a system for recognition of on-line cursive Hangul (Korean characters) by means of DP matching of structural information. The penalty function has the following special features. In order to prevent short spurious strokes from causing large penalties, an input stroke is weighted by its length relative to other input strokes. In order to make use of pen-up and pen-down information, a penalty is incurred when 2 strokes of differing type (i.e. pen-up with pen-down) are matched. Finally, to reduce the chance of obtaining a suboptimal solution which can result from using the greedy algorithm in DP matching, we look-ahead an extra match. In a computer simulation we obtained a recognition rate of 92% for partially cursive characters and 89% for fully cursive characters. Furthermore, for both cases combined the correct character appears 98% of the time in the top 10 candidates. Thus we confirmed that the proposed algorithm is effective in recognizing cursive Hangul.

A computer-based system for the automatic determination of the physical parameters of rainfall was developed. The measuring device consists of a light source and two TV cameras. Images of raindrops that fell through the slit were observed on a frosted glass plate as shadow images which were photographed simultaneously by two TV cameras with different shutter speeds and analyzed. The data indicated that the shape of raindrops were spheroid in case of small diameter but were slightly deformed into an oblate spheroid in case of larger diameter, and the fall velocity tends to increase with increasing size of raindrops. Rainfall rates calculated from the shape and velocity were compared with those measured directly and found to agree.

The Australian research in the field of microwave technology is not very large. However we have some small but reasonably advanced capability and achievements. In this paper some of the Australian developments are discussed namely: GaAs Monolithic Microwave Integrated Circuits, MM-wave Local Area Networks, Antennas for Communications and Radioastronomy and application of Photonics to Warfare.

Interdigital transducers (IDTs) with leaky-SAWs propagating on 36 YX-LiTaO3, and 41 and 64 YX-LiNbO3 were theoretically analyzed, providing a new equivalent circuit. This equivalent circuit included attenuation constant due to leakage as well as conductance caused by bulkwave radiation. All circuit parameters were derived by solving integral equations. Fundamental experiments showed fairly good agreement between theoretical and experimental results, which gave very accurate design tools for leaky-SAW devices.

A new mm-wave IC, constructed by flip-chip bonded heterojunction transistors and microstrip lines formed on Si substrate, has been proposed and demonstrated by using MBB (micro bump boding) technology. Millimeter-wave characteristics of the MBB region has been estimated by electro-magnetic field analysis. Good agreements between calculated and measured characteristics of this new IC (named MFIC: millimeter-wave flip-chip IC) have been obtained up to 60 GHz band. Several MFIC amplifiers with their designed performances have been successfully fabricated.

In this letter, we introduce a predictor based least square (PLS) algorithm. By involving both order- and time-update recursions, the PLS algorithm is found to have a more stable performance compared with the stable version (Version II) of the RLS algorithm shown in Ref.[1]. Nevertheless, the computational requirement is about 50% of that of the RLS algorithm. As an application, the PLS algorithm can be applied to the fast Newton transversal filters (FNTF). The FNTF algorithms suffer from the numerical instability problem if the quantities used for extending the gain vector are computed by using the fast RLS algorithms. By combing the PLS and the FNTF algorithms, we obtain a much more stable performance and a simple algorithm formulation.

This paper proposes a novel architecture and MMICs for an integrated 2-32 GHz front-end of a spectrum analyzer. The architecture achieves miniaturization by eliminating the large YIG tracking filter and also achieves multi-octave measurement with less than one octave sweep of the first local oscillator. The MMIC's demonstrate ultra-wideband performances with reduced chip sizes by utilizing newly developed FET cells for power combination, multi-order frequency conversion, low leakage variable resistance, and active impedance translation. The MMIC's are a fundamental/harmonic frequency converter, a variable attenuator, a single-pole triple-throw switch, a single-pole double-throw switch, a distributed pre-amplifier, and an active LC lowpass filter. All the MMIC's are smaller than 1 mm2, except the pre-amplifier and the filter.

Design techniques are presented for high performance microstrip bandpass filters using GaAs FETs for loss compensation. The filters are based on conventional planar filter topologies with the addition of GaAs FET negative resistance circuits to amplify the signal within the resonators via a reflection-mode of amplification. Three practical filters have been demonstrated using these negative resistance techniques: (1) A filter employing an active loop configuration, (2) a dual-mode microstrip ring resonator filter, and (3) an end-coupled half-wavelength resonator filter. The investigation of this negative resistance method of loss compensation has led to the development of an exciting new type of miniaturised filter which employs MIC microstrip resonators with MMIC negative resistance chips bonded into the filter for loss compensation. This approach has the advantage of combining the proven capabilities of established MIC microstrip filter topologies with the excellent reproducibility of the MMIC loss compensation circuits.

In this paper, mutual coupling S21 between RMSA (ring-shaped microstrip antenna) elements was estimated by the EMF method based on the cavity model. Then, the validity of the proposed method was tested by experiments. The experiments confirmed satisfactory agreement between the computed and experimental data for S21 in both E- and H-plane arrangements. In addition, a circularly polarized planar array composed of R-MSA elements was designed on the basis of the data of S21. The experimental results of such a planar array demonstrated high performance in radiation pattern as well as axial ratio property. Furthermore, the active reflection coefficient Γ in the R-MSA array was also investigated in both equilateral and square arrangements. The computed results of active reflection coefficient in the array demonstrated high performance in both arrangements.

The high-Tc superconducting active antenna proposed here for millimeter and submillimeter radiowave communications, uses a YBCO slot antenna with a series Josephson junction array to increase the normal-state resistance of the junctions, in order to ensure impedance matching between the antenna and the junctions. The antenna is a coplanar waveguide fed slot antenna, which can be easily and monolithically combined with the Josephson junctions. The design frequency of the antenna is 10 GHz and the obtained bandwidth of a VSWR less than 2 was 4.1%. Normal-state resistance values of the junction array could be confirmed by measuring I-V characteristics and 100-MHz impedance measurements, and both agree very well. Microwave mixing experiments were carried out using the junction array with the antenna, and the experiments showed that the conversion gain of the junction was proportional to the number of the junctions. The conversion gain of an eight-junction mixer with the antenna was found to be -6 dB.

The dielectric resonator technique is commonly used for microwave surface resistance measurements of High Temperature superconducting (HTS) films. Thickness of super-conductors and its impact on measurement results has not been taken into consideration so far. A theoretical mode-matched solution analysis of a TE011 10 GHz sapphire resonator was performed. The results of this analysis demonstrate that the thickness of the films under test can significantly affect the resonant frequencies (fres) and quality factor Q of the resonant system, particularly when the thickness is less than three times the penetration depth (λ) of the films at the operating temperature. In such cases the microwave properties of the substrate affect fres and Q. For HTS films' thickness relatively small as compared to λ, measured quality factors and resonant frequency may also be affected by substrate thickness and the conductivity of the backing plates of the system. The presence of air gaps between the sapphire and the HTS films does not significantly influence surface resistance measurements. However they can markedly affect the surface reactance from which the penetration depth is calculated.

A Ku-band transversal filter with a center frequency of 12 GHz and a bandwidth of 6 GHz using directional couplers made of a multilayer ceramic has been proposed and developed. The directional coupler can realize a wide range of frequency characteristics, e.g. coupling of 3.50.5 dB in the frequency range of 10 to 17 GHz and a wide range of coupling values, i.e. 3 to 35 dB. Calculations have confirmed that the increase in insertion loss due to a decreasing Q-factor can be much less than that for a resonator filter. The transversal filter was fabricated without additional tuning, and measured results agreed well with calculated values.

An experimental study on propagation characteristics in a room of a modern office building using a 57.5 GHz carrier is described. The objective of the study is to provide initial information about the path-loss and fading characteristics for millimeter-wave wireless indoor communication systems. The area of the floor of the room is about 90 m2 and the room was almost empty with no furniture except the experimental apparatus. A wide-beam scalar feed horn transmission antenna and an omnidirectional receiving antenna were used and set to be with the same height. The measured area was divided into many "squares" to characterize the propagation. The variation of square transmission loss was calculated, and the regions where the maximum square transmission loss was observed were pointed out. It became clear that the distance power law for square transmission loss was approximately of the order d-2 along the direct path. Rician distributions for fast fading were derived in almost all squares of this room. The spectra for the fast fading envelope were also derived. From the propagation point of view, the results show that no extreme difficulty seems to exist in developing wireless communication systems in the 60 GHz band.

Improvement of the convergence characteristics of the NLMS algorithm has received attention in the area of adaptive filtering. A new variable stepsize NLMS method, in which the stepsize is updated optimally by using variances of the measured error signal and the estimated noise, is proposed. The optimal control equation of the stepsize has been derived from a convergence characteristic approximation. A new condition to judge convergence is introduced in this paper to ensure the fastest initial convergence speed by providing precise timing to start estimating noise level. And further, some adaptive smoothing devices have been added into the ADF to overcome the saturation problem of the identification error caused by some random deviations. By the simulation, The initial convergence speed and the identification error in precise identification mode is improved significantly by more precise adjustment of stepsize without increasing in computational cost. The results are the best ever reported performanced. This variable stepsize NLMS-ADF also shows good effectiveness even in severe conditions, such as noisy or fast changing circumstances.

A bottleneck identification methodology is proposed for the performance-oriented design of shared-bus multiprocessors, which are composed of several major subsystems (e.g. off-chip cache, bus, memory, I/O). A subsystem with the longest access time per instruction is the one that limits processor performance and creates a bottleneck to the system. The methodology also facilitates further refined analysis on the access time of the bottleneck subsystem to help identify the causes of the bottleneck. Example performance model of a particular shared-bus multiprocessor architecture with separate address bus and data bus is developed to illustrate the key idea of the bottleneck identification methodology. Accessing conflicts in subsystems and DMA transfers are also considered in the model.

An adaptive digital filter with adaptive sampling phase is proposed. The structure of the filter makes use of an adaptive delay device at the input of the filter. The algorithm is derived to determine the value of the delay and the filter coefficients by minimizing MSE (mean square error) between the desired signal and the filter output. The computer simulation of the convergence of the proposed adaptive filter with the input of sinusoidal wave and BPSK modulated wave are shown. According to the simulation, the MSE of the proposed adaptive delay algorithm is lower than that of the conventional LMS algorithm.

This paper presents an improved neural network for channel assignment problems in cellular mobile communication systems in the new co-channel interference model. Sengoku et al. first proposed the neural network for the same problem, which can find solutions only in small size cellular systems with up to 40 cells in our simulations. For the practical use in the next generation's cellular systems, the performance of our improved neural network is verified by large size cellular systems with up to 500 cells. The newly defined energy function and the motion equation with two heuristics in our neural network achieve the goal of finding optimum or near-optimum solutions in a nearly constant time.