In this paper, a novel noise parameters extraction technique for microwave packaged BJT and FET is proposed. The noise parameters of packaged BJT and FET for the entire operating frequency band can be obtained from the four noise parameters measured at a single frequency or a few frequencies. The predicated results obtained with this method agree well with the measured data. As a result, the novel noise parameters extraction technique can be used to predict the noise with a minimum effort.

Interdigital transducers (IDTs) with leaky-SAWs propagating on 36 YX-LiTaO3, and 41 and 64 YX-LiNbO3 were theoretically analyzed, providing a new equivalent circuit. This equivalent circuit included attenuation constant due to leakage as well as conductance caused by bulkwave radiation. All circuit parameters were derived by solving integral equations. Fundamental experiments showed fairly good agreement between theoretical and experimental results, which gave very accurate design tools for leaky-SAW devices.

In this paper, we presented an analysis of single and coupled microstrip lines covered with protective dielectric film which is usually used in the microwave integrated circuits. The method employed in the characterization is called partial-boundary element method (p-BEM). The p-BEM provides an efficient means to the analysis of the structures with multilayered media or covered with protective dielectric film. The numerical results show that by changing the thickness of the protective dielectric films such as SiO2, Si and Polyimide covered on these lines on a GaAs substrate, the coupled microstrip lines vary within 10% on the characteristic impedance and within 25% on the effective dielectric constant for the odd mode of coupled microstrip line, respectively, in comparison with the structures without the protective dielectric film. In contrast, the single microstrip lines vary within 4% on the characteristic impedance and within 8% on the effective dielectric constant, respectively. The protective dielectric film affects the odd mode of the coupled lines more strongly than the even mode and the characteristics of the single microstrip lines.

The fundamental TE10 mode in a rectangular waveguide of a square cross section is degenerate with TE01 mode. A quarter wavelength resonator made of a dielectric square waveguide is, therefore, applied for a small-sized bandpass filter, just like dual mode filters for base stations in the mobile communication. In this paper, the methods to couple the two modes are first studied, including cutting a corner of the resonator and adding some metal electrodes on its end face. Both methods help to flow the rf current of the odd mode at the corner, resulting in decrease of the series inductance and thus increase of the resonant frequency. The coupling constant, that is proportional to the difference of the odd and even-mode's resonant frequency, can be controlled by the perturbations mentioned above. The coupling to the external circuit is adjusted by an electrode fabricated also on the end face. It is connected to a microstrip line and capacitively couples to the resonant modes. The coupling strength increases with the dimension of the electrode. The adjustment of the resonant frequency is carried out by the similar electrode on the end face and connected to the center of the side of the square cross section. The frequency decreases with the length of the electrode. The unloaded Q is measured to be of around 500 for 5510 mm resonator of εr=93. The optimum aspect ratio for the resonator is found in terms of the Q value. The simplest bandpass filter, i.e., a two-stage bandpass filter is designed and fabricated using 5510 mm resonator. It is mounted in a square hole made in a printed circuit board and excited by a microstrip line. The frequency characteristics are in good agreement with the expected values.

This paper presents an analytical study and computer-based model of radio wave polarization propagating through a microcell. It covers the following topics: the influence of random orientation of a handset terminal on the performance of communication systems using either a linearly or circularly polarized base-station antenna; an analysis of the computer-based simulation of the power response on different polarizations in a street-canyon microcell.

Distributed computing over a network of workstations continues to be an illusive goal. Its main obstacle is the delay penalty due to network protocol and OS overhead. We present in this paper a low level hardware supported scheme for managing distributed shared memory (DSM), as an underlying paradigm for distributed computing. The proposed DSM is novel in that it employs a two-tier paging scheme that reduces the probability of false sharing and facilitates an efficient hardware implementation. The scheme employs a standard OS page and divides it into fixed smaller memory units called paragraphs, similar to cache lines. This scheme manages the shared data regions only, while other regions are handled by the OS in the standard manner without modification. A hardware extension of a traditional MMU, namely Distributed MMU or DMMU, is introduced to support the DSM. Shared memory coherency is maintained through a write-invalidate protocol. An analytical model is built to evaluate the system sensitivity to various parameters and to assess its performance.

A 1.5 GHz band Si power MOS amplifier module with 50% total efficiency, 1 W output power and 30 dB power gain has been developed for front-end transmitter of digital cellular telephones. A combination of a highly efficient power MOSFET for the output stage and an integrated two stage MOS amplifier for the driver with an impedance matching circuit minimizing the length of striplines made it possible to achieve high total efficiency, high power gain, and smaller size of the amplifier module.

A fiber optic temperature sensor using a conventional graded index multimode optical fiber is proposed. The multimode fiber is excited by two selected modes using a computer-generated holographic filter. A clear periodic signal created by interference between two modes is observed in the experiment.

A 3.3 V single power-supply 64 Mb flash memory with a DBL programming scheme has been developed and fabricated with 0.4 µm CMOS technology. 50 ns access time and 256 b erase/programming unit-capacity have been achieved by using hierarchical word- and bit-line structures and DBL programming scheme. Furthermore in order to lower operating voltage the HiCR cell is used. The chip size is 19.3 mm13.3 mm.

An optimum design scheme for logical network topologies on a Flexible Multi-QoS Logical ATM Network, named Full-Net, is proposed. Full-Net offers high-quality Virtual-Path (VP) networks and controls end-to-end QoS only at the VP-network's access points. To develop the optimum network topology for multimedia traffic in a single ATM network, a logically con figured Virtual Channel Handler (VCH) interconnection network is associated with each QoS class. Many logical networks can be mapped at the same time on the same network, because mapping is independent of the network's physical implementation. To achieve an optimum design scheme for logical networks, the number of disjoint routes is introduced as the parameter used to optimize logical network topology. The number of disjoint routes is chosen so as to maximize total network efficiency. The optimum number of disjoint routes depends on the required QoS, VC-traffic characteristics, and traffic demand. By choosing the relevant cost characteristics, the network operator can easily maximize network efficiency and provide customers with the QoS they request at minimum cost. The proposed optimum multi-QoS network design scheme on a Full-Net architecture is an efficient solution to implementing multi-QoS control in an ATM network.

Transition coverage has been proposed as a measure of two-pattern test capabilities of TPG circuits for use in BIST. This paper investigates experimentally the relationships between transition coverages and actual stuck-open fault coverages in order to reveal what kind of circuits are appropriate for two-pattern testing. Fault simulation was performed using conventional (n-stage) LFSR, 2n-stage LFSR, and one-dimensional cellular automata (CAs) as TPG circuits and such sample circuits as balanced NAND tree and some ISCAS '85 benchmark circuits as CUTs. It was found that CAs which are designed so as to apply exhaustive transitions to any 3-dimensional subspaces can detect high rate of stuck-open faults. Influence of hazards of decreasing the fault coverage is also mentioned.

The word error probability of linear block codes is computed for diversity systems with maximal ratio combining in mobile communications with three decoding algorithms: error correction (EC), error/erasure correction (EEC), and maximum likelihood (ML) soft decoding algorithm. Ideal interleaving is assumed. EEC gives 0.1-1.5dB gain over EC. The gain of EEC over EC decreases as the number of diversity channels increases. ML soft gives 1.8-5.5dB gain over EC.

The advance of mobile network and radio techniques has been rapidly expanding the service area for mobile terminals. Thus, mobile communications have been devoted to the improvement of terminal mobility (TM). Recently, the personal mobility (PM) concept appeared which gives a freedom to use personal telecommunication numbers at any terminal. Therefore, mobile network must next enable a user to access telecommunication services with his/her personal telecommunication number from any terminal at any geographic location. In other words, the mobile network must implement universal mobility (UM) that integrates TM and PM. This paper first provides a definition of UM. Next, it describes the identity and number configurations for UM and then presents network techniques for UM, i.e., the network architecture and UM management procedures. It also presents the current status of standardization on UM in the Personal Digital Cellular system (PDC) and Future Public Land Mobile Telecommunication Systems (FPLMTS).

The dynamics of an artificial neural network derived from a biological system, and its two applications to engineering problems are examined. The model has a multi-layer structure simulating the primary and secondary components in the olfactory system. The basic element in each layer is an oscillator which simulates the interactions between excitatory and inhibitory local neuron populations. Chaotic dynamics emerges from interactions within and between the layers, which are connected to each other by feedforward and feedback lines with distributed delays. A set of electroencephalogram (EEG) obtained from mammalian olfactory system yields aperiodic oscillation with 1/f characteristics in its FFT power spectrum. The EEG also reveals abrupt state transitions between a basal and an activated state. The activated state with each inhalation consists of a burst of oscillation at a common time-varying instantaneous frequency that is spatially amplitude-modulated (AM). The spatial pattern of the activated state seems to represent the class of the input ot the system, which simulates the input from sensory receptors. The KIII model of the olfactory system yields sustained aperiodic oscillation with "1/f" spectrum by adjustment of its parameters. Input in the form of a spatially distributed step funciton induces a state transition to an activated state. This property gives the model its utility in pattern classification. Four different methods (SD, RMS, PCA and FFT) were applied to extract AM patterns of the common output wave forms of the model. The pattern classification capability of the model was evaluated, and synchronization of the output wave form was shown to be crucial in PCA and FFT methods. This synchronization has also been suggested to have an important role in biological systems related to the information extraction by spatiotemporal integration of the output of a transmitting area of cortex by a receiving area.

A new concept for a navigation and communication satellite system has been proposed. The navigation satellite system that forms the basis of the proposed system has been studied by one of the authors and extended to add a mobile communication function to the system. The satellite system consists of 15 satellites in quasi-geostationary orbit (QGEO) that have a geostationary altitude and high inclination and provide global coverage and positioning capability to the observer through only reception of the range measurement signals generated at the satellites, which are in the same configuration as the satellites in Global Positioning System (GPS), Three satellites out of the 15 satellite are designated to install a subsystem for mobile satellite communication in order to satisfy mobile communication convenience as required in a Future Air Navigation System's (FANS) concept of International Civil Aviation Organization (ICAO). The case studies of 15-satellites constellations demonstrate not only an acceptable positioning accuracy over the whole globe, but also an accuracy distribution weighted on the north pole region as an example of a weighted accuracy distribution. The addition of a mobile communication function suggests a unified system of satellite navigation and communication, which might provide convenience for the civil aviation industry, because the two functions currently depend on different systems.

We compared--for the same propagation conditions and parameters--the performances of distributed dynamic channel assignment (DDCA) strategies and the performance of fixed channel assignment (FCA). This comparison quantitatively showed the effects of DDCA strategies in increasing spectrum efficiency. It also showed that using DDCA with transmitter power control (TPC) increases the system capacity to 3 4 times what it is with FCA and to 1.4 1.8 times what it is when using DDCA without TPC. We also evaluated the blocking rate and the interference probability for the inside of a cell and found that these are generally much higher close to the cell border than they are near the base station.

The applicability of Dynamic Channel Assignment methods to a Reuse Partitioning system in cellular radio systems is investigated in this paper. The investigations indicate that such a system has a tendency to increase the difference between blocking probability for the partitioning two coverage areas in comparison with the conventional Reuse Partitioning system employing Fixed Channel Assignment method. Two schemes using new Channel Rearrangement algorithms are also proposed in order to alleviate the difference as a disadvantage which gives unequal service to the system. The simulation results show that the proposed schemes are able to reduce the difference significantly while increasing the carried traffic by 10% as compared with the conventional system.

This paper discussed a distributed processing architecture for a virtual space teleconferencing system. Virtual space teleconferencing is a promising application field for networked virtual environments. People in different places will be able to meet each other in a virtual teleconferencing room and proceed with various cooperative tasks. When such a system creates a realistic virtual environment, it can be referred to as a "Teleconferencing with realistic sensations" system. Further more, as the conference environment can be shared by a number of users, it is possible to perform various kinds of cooperative work using the system. In this paper, the architecture for networked multi-user virtual space systems are classified, and then a case study is described for building a proposed teleconferencing system. The system reproduces a 3D image of each conference participant in a virtual meeting room. Compared with the former system, the new system can deal with more than three participants at the same time and can connect them through commercial telephone lines. Based on the virtual world database management structure, the system was classified as a central server system. However, a central server architecture limits the number of conference sites. We confirmed that the system can serve up to 14 sites using multi-modal interaction without significant latency in operation from summational experiments. Then, introducing some assumptions to the results, we have proposed processing model of the system. The results of model could describe the experimental results and we could indicate roughy estimated system capacity to realize a requaied system performance.

This paper presents the concept of k-FR circuits. The controllability of such a circuit is high due to its special structure. It is shown that all stuck-at faults and stuck-open faults in a k-FR circuit can be detected and located by k(k1)1 test vectors under the highly observable condition which assumes the output of every gate to be observable. k is usually two or three. This paper also presents an algorithm for converting an arbitrary combinational circuit into a k-FR circuit. A k-FR circuit is easy to test when using technologies such as the electron-beam probing, the current measurement, or the CrossCheck testability solution.

Multimedia communication services are being made available with the advent of broadband optical fiber networks. As many different services will be accommodated in such networks, network survivability has been recognized to be a crucial concern. In this paper, we propose a new restoration algorithm for ATM networks providing multimedia services. Our proposed restoration algorithm adopts the message bundling scheme of the Multi-Destination Flooding (MDF) algorithm which was previously proposed for STM-based networks to handle catastrophic failures such as multiple link and node failures. Virtual Paths (VP) with the same communication speed are bundled and Operation Administration and Maintenance (OAM) cells are used for communication of restoration messages. In addition, the following modifications are made on the original MDF to improve restoration performance. The pre-cancellation scheme is adopted to arbitrate reservation contention to realize high restoration ratio. The dual queue scheme is applied to avoid congestion of restoration messages. Moreover, the connection control scheme for VPI connections is proposed to prevent alternative routes from being misconnected. This paper describes the design concept of our restoration algorithm, processes in each restoration phase, and the performance evaluation by computer simulation.