This paper demonstrates the suppressing power of 10 Gbps On Off keyed signal using biased half-wave rectification. Authors have previously reported that radio frequency (RF) and optical on-off keying (OOK) signal can be simultaneously transmitted over the radio over fiber (RoF) link [1]. Since the optical OOK signal has much broader bandwidth compared to RF signal, it interferes with RF signal. Reference [1] experimentally shows that the optical OOK signal degrades the RF signal in terms of signal-to-noise power ratio (SNR) when 10 Gbps OOK and 1.9 GHz microwave are employed as baseband and RF, respectively. This paper proposes an interference suppression, and the proposal is subsequently used for detecting the RF signal. Experiments are conducted for the purpose of the proof-of-concept of the proposal. Finally numerical simulations are employed to show the performance enhancement in terms of error vector magnitude (EVM).

This paper presents a 27.5-29.6GHz fractional-N frequency synthesizer using reference and frequency doublers to achieve low in-band and out-of-band phase-noise for 5G mobile communications. A consideration of the baseband carrier recovery circuit helps estimate phase noise requirement for high modulation scheme. The push-push amplifier and 28GHz balun help achieving differential signals with low out-of-band phase noise while consuming low power. A charge pump with gated offset as well as reference doubler help reducing PD noise resulting in low in-band phase noise while sampling loop filter helps reduce spurs. The proposed synthesizer has been implemented in 65nm CMOS technology achieving an in-band and out-of-band phase noise of -78dBc/Hz and -126dBc/Hz, respectively. It consumes only a total power of 33mW. The jitter-power figure-of-merit (FOM) is -231dB which is the highest among the state of the art >20GHz fractional-N PLLs using a low reference clock (<200MHz). The measured reference spurs are less than -80dBc.

In the process of VLSI design, ECO (Engineering Change Order) may occur at any design phase. When ECO happens after the netlist is generated and optimized, designers may like to modify the netlist directly. This is because if ECO is performed in the high-level description, the netlist should be resynthesized and the result may be significantly different from the original one, even if the modification in the high-level description is small. As the result, the efforts spent on optimization so far may become useless. When the netlist is modified directly, the C description should be revised accordingly. This paper proposes a method to reconstruct a C description from the revised netlist. In the proposed method, designers need to provide a template represented in C, which has some vacant (blanked) places and is created from the original C description. The vacant places are automatically synthesized using a CEGIS-based method (Counter Example Guided Inductive Synthesis). Using a set of use-cases, our method tries to find the correct expressions for the vacant places so that the entire description becomes functionally equivalent to the given modified netlist, by only simulating the netlist. Experimental results show that the proposed method can reconstruct C descriptions successfully within practical time for several examples including the one having around 9,000 lines of executable statements. Moreover, the proposed method can be applied to equivalence checking between a netlist and a C description, as shown by our experimental results.

Investigative reports plagiarized from the web should be eliminated because such reports result in ineffective knowledge construction. In this study, we developed an investigative report writing support system for effective knowledge construction from the web. The proposed system attempts to prevent plagiarism by restricting copying and pasting information from web pages. With this system, students can verify information through web browsing, externalize their constructed knowledge as notes for report materials, write reports using these notes, and remove inadequacies in the report by reflection. A comparative experiment showed that the proposed system can potentially prevent web page plagiarism and make knowledge construction from the web more effective compared to a conventional report writing environment.

Online chat systems, e.g.., Twitter and Slack, have been used in academic conferences or study meetings as a means of instant discussion and sharing related information alongside a real presentation. We propose a system for activating online discussion by providing a bot that suggests webpages related to current timeline of the discussion. Our system generates keyword vectors according to discussion timeline, searches best related webpages from several web sites, and timely provides these pages to the discussion timeline. This paper describes deployments of our system in two types of meetings: lightning talk format meetings and group meetings; and daily exchanges using online chat system. As a result, we could not find good enough reactions to the bot's postings from meeting participants at the lightning talk format meetings, but we could observe more reactions and progress of discussion caused by the bot's postings at the relaxed meetings and daily exchanges among group members.

This work presents a hybrid formulation of the stochastic reduced order model (SROM) algorithm, which makes use of Gauss quadrature, a key ingredient of the stochastic collocation method, to avoid the cumbersome optimization process required by SROM for optimal extraction of the sample set. With respect to classic SROM algorithms, the proposed formulation allows a significant reduction in computation time and burden as well as a remarkable improvement in the accuracy and convergence rate in the estimation of statistical moments. The method is here applied to a specific case study, that is the prediction of crosstalk in a two-conductor wiring structure with electrical and geometrical parameters not perfectly known. Both univariate and multivariate analyses are carried out, with the final objective being to compare the performance of the two SROM formulations with respected to Monte Carlo simulations.

In this paper, we investigate the capacity performance of an in-band full-duplex (IBFD) amplify-and-forward two-way relay system under the effect of residual loop-back-interference (LBI). In a two-way IBFD relay system, two IBFD nodes exchange data with each other via an IBFD relay. Both two-way relaying and IBFD one-way relaying could double the spectrum efficiency theoretically. However, due to imperfect channel estimation, the performance of two-way relaying is degraded by self-interference at the receiver. Moreover, the performance of the IBFD relaying is deteriorated by LBI between the transmit antenna and the receive antenna of the node. Different from the IBFD one-way relay scenario, the IBFD two-way relay system will suffer from an extra level of LBI at the destination receiver. We derive accurate approximations of the average end-to-end capacities for both the IBFD and half-duplex modes. We evaluate the impact of the LBI and channel estimation errors on system performance. Monte Carlo simulations verify the validity of analytical results. It can be shown that with certain signal-to-noise ratio values and effective interference cancellation techniques, the IBFD transmission is preferable in terms of capacity. The IBFD two-way relaying is an attractive technique for practical applications.

A dynamic neural network has ternary connection parameters and can generate various binary periodic orbits. In order to analyze the dynamics, we present two feature quantities which characterize stability and transient phenomenon of a periodic orbit. Calculating the feature quantities, we investigate influence of connection sparsity on stability of a target periodic orbit corresponding to a circuit control signal. As the sparsity increases, at first, stability of a target periodic orbit tends to be stronger. In the next, the stability tends to be weakened and various transient phenomena exist. In the most sparse case, the network has many periodic orbits without transient phenomenon.

This paper presents a supervised method to classify a document at the sub-sentence level. Traditionally, sentiment analysis often classifies sentence polarity based on word features, syllable features, or N-gram features. A sentence, as a whole, may contain several phrases and words which carry their own specific sentiment. However, classifying a sentence based on phrases and words can sometimes be incoherent because they are ungrammatically formed. In order to overcome this problem, we need to arrange words and phrase in a dependency form to capture their semantic scope of sentiment. Thus, we transform a sentence into a dependency tree structure. A dependency tree is composed of subtrees, and each subtree allocates words and syllables in a grammatical order. Moreover, a sentence dependency tree structure can mitigate word sense ambiguity or solve the inherent polysemy of words by determining their word sense. In our experiment, we provide the details of the proposed subtree polarity classification for sub-opinion analysis. To conclude our discussion, we also elaborate on the effectiveness of the analysis result.

In current large-scale IT systems, troubleshooting has become more complicated due to the diversification in the causes of failures, which has increased operational costs. Thus, clarifying the troubleshooting process also becomes important, though it is also time-consuming. We propose a method of automatically extracting a workflow, a graph indicating a troubleshooting process, using multiple trouble tickets. Our method extracts an operator's actions from free-format texts and aligns relative sentences between multiple trouble tickets. Our method uses a stochastic model to detect a resolution, a frequent action pattern that helps us understand how to solve a problem. We validated our method using real trouble-ticket data captured from a real network operation and showed that it can extract a workflow to identify the cause of a failure.

NAND flash memories used in solid-state drives (SSDs) will be replaced with storage-class memories (SCMs), which are comparable with NAND flash in their cost, and with DRAM in their speed. This paper describes the performance difference of the SCM/NAND flash hybrid SSD and the SCM-based SSD with between sector-unit read (512 Byte) and page-unit read (16 KByte, NAND flash page-size) using synthetic and real workload. Also, effect of the SCM read-unit size on SSD performance are analyzed. When SCM write/read latency is 0.1 us, performance difference of the SCM/NAND flash hybrid SSD with between page- and sector-unit read is about 1% and 6% at most for the write-intensive and read-intensive workloads, respectively. However, performance of the SCM-based SSD is significantly improved when sector-unit read is used because extra read latency does not occur. Especially, the SCM-based SSD IOPS is improved by 131% for proj_3 (read-hot-random), because its read request size is small but its read request ratio is large. This paper also shows IOPS of SCM-based SSD write/read with sector-unit read can be predicted by the average write/read request size of workloads.

This paper addresses the issue of modeling the discourse nature of lyrics and presented the first study aiming at capturing the two common discourse-related notions: storylines and themes. We assume that a storyline is a chain of transitions over topics of segments and a song has at least one entire theme. We then hypothesize that transitions over topics of lyric segments can be captured by a probabilistic topic model which incorporates a distribution over transitions of latent topics and that such a distribution of topic transitions is affected by the theme of lyrics. Aiming to test those hypotheses, this study conducts experiments on the word prediction and segment order prediction tasks exploiting a large-scale corpus of popular music lyrics for both English and Japanese (around 100 thousand songs). The findings we gained from these experiments can be summarized into two respects. First, the models with topic transitions significantly outperformed the model without topic transitions in word prediction. This result indicates that typical storylines included in our lyrics datasets were effectively captured as a probabilistic distribution of transitions over latent topics of segments. Second, the model incorporating a latent theme variable on top of topic transitions outperformed the models without such variables in both word prediction and segment order prediction. From this result, we can conclude that considering the notion of theme does contribute to the modeling of storylines of lyrics.

We present an 82.5GS/s over-sampling based burst-mode clock and data recovery (BM-CDR) IC chip-set comprising an 82.5GS/s over-sampling IC using 8×10.3GHz multi-phase clocks and a dual-rate data selector logic IC to realize the 10.3Gb/s and 1.25Gb/s dual-rate burst-mode fast-lock operation required for 10-Gigabit based fiber-to-the-x (FTTx) services supported by 10-Gigabit Ethernet passive optical network (10G-EPON) systems. As the key issue for designing the proposed 82.5GS/s BM-CDR, a fresh study of the optimum number of multi-phase clocks, which is equivalent to the sampling resolution, is undertaken, and details of the 10.3Gb/s cum 1.25/Gb/s dual-rate optimum phase data selection logic based on a blind phase decision algorithm, which can realize a full single-platform dual-rate BM-CDR, ate also presented. By using the power of the proposed 82.5GS/s over-sampling BM-CDR in cooperation with our dual-rate burst-mode optical receiver, we further demonstrated that a short dual-rate and burst-mode preamble of 256ns supporting receiver settling and CDR recovery times was successfully achieved, while obtaining high receiver sensitivities of -31.6dBm at 10.3Gb/s and -34.6dBm at 1.25Gb/s and a high pulse-width distortion tolerance of +/-0.53UI, which are superior to the 10G-EPON standard.

In this paper, an optimal method is proposed to design sparse-coefficient notch filters with principal basic vectors in the column space of a matrix constituted with frequency samples. The proposed scheme can perform in two stages. At the first stage, the principal vectors can be determined in the least-squares sense. At the second stage, with some components of the principal vectors, the notch filter design is formulated as a linear optimization problem according to the desired specifications. Optimal results can form sparse coefficients of the notch filter by solving the linear optimization problem. The simulation results show that the proposed scheme can achieve better performance in designing a sparse-coefficient notch filter of small order compared with other methods such as the equiripple method, the orthogonal matching pursuit based scheme and the L1-norm based method.

Knowledge management is important for government agencies in improving service delivery to their customers and data inter-operation within and across organizations. Building organizational knowledge repository for government agency has unique challenges. In this paper, we propose that enterprise ontology can provide support for government agencies in capturing organizational taxonomy, best practices and global data schema. A case study of a large-scale adoption for the Thailand's Excise Department is elaborated. A modular design approach of the enterprise ontology for the excise tax domain is discussed. Two forms of organizational knowledge: global schema and standard practices were captured in form of ontology and rule-based knowledge. The organizational knowledge was deployed to support two KM systems: excise recommender service and linked open data. Finally, we discuss some lessons learned in adopting the framework in the government agency.

Capital expenditure (CAPEX) reduction and efficient wavelength allocation are critical for the future access networks. Elastic lambda aggregation network (EλAN) based on WDM and OFDM technologies is expected to realize efficient wavelength allocation. In this paper, we propose adaptive bandwidth allocation (ABA) algorithm for EλAN under the conditions of crowded networks, in which modulation format, symbol rate and the number of sub-carriers are adaptively decided based on the distance of PON-section, QoS and bandwidth demand of each ONU. Network simulation results show that the proposed algorithm can effectively reduce the total bandwidth and achieve steady high spectrum efficiency and contribute to the further reduction of CAPEX of future optical access networks.

The widespread application of mobile electronic devices has triggered a boom in energy consumption, especially in user equipment (UE). In this paper, we investigate the energy-efficiency (EE) of a UE experiencing the worst channel conditions, which is termed worst-EE. Due to the limited battery of the mobile equipment, worst-EE is a suitable metric for EE fairness optimization in the uplink transmissions of orthogonal frequency division multiple access (OFDMA) networks. More specifically, we determine the optimal power and sub-carrier allocation to maximize the worst-EE with respect to UEs' transmit power, sub-carriers and statistical quality-of-service (QoS). In order to maximize the worst-EE, we formulate a max-min power and sub-carrier allocation problem, which involves nonconvex fractional mixed integer nonlinear programming, i.e., NP-hard to solve. To solve the problem, we first relax the allocation of sub-carriers, formulate the upper bound problem on the original one and prove the quasi-concave property of objective function. With the aid of the Powell-Hestenes-Rockfellar (PHR) approach, we propose a fairness EE sub-carrier and power allocation algorithm. Finally, simulation results demonstrate the advantages of the proposed algorithm.

We propose a radiation-hardened Flip-Flop (FF) with stacked transistors based on the Adaptive Coupling Flip-Flop (ACFF) with low power consumption in a 65 nm FDSOI process. The slave latch in ACFF is much weaker against soft errors than the master latch. We design several FFs with stacked transistors in the master or slave latches to mitigate soft errors. We investigate radiation hardness of the proposed FFs by α particle and neutron irradiation tests. The proposed FFs have higher radiation hardness than a conventional DFF and ACFF. Neutron irradiation and α particle tests revealed no error in the proposed AC Slave-Stacked FF (AC_SS FF) which has stacked transistors only in the slave latch. We also investigate radiation hardness of the proposed FFs by heavy ion irradiation. The proposed FFs maintain higher radiation hardness up to 40 MeV-cm2/mg than the conventional DFF. Stacked inverters become more sensitive to soft errors by increasing tilt angles. AC_SS FF achieves higher radiation hardness than ACFF with the performance equivalent to that of ACFF.

Vehicular Ad hoc Network (VANET) is an important part of the Intelligent Transportation System (ITS). VANETs can realize communication between moving vehicles, infrastructures and other intelligent mobile terminals, which can greatly improve the road safety and traffic efficiency effectively. Existing studies of vehicular ad hoc network usually consider only one data transmission model, while the increasing density of traffic data sources means that the vehicular ad hoc network is evolving into Heterogeneous Vehicular Network (HetVNET) which needs hybrid data transmission scheme. Considering the Heterogeneous Vehicular Network, this paper presents a hybrid transmission MAC protocol including vehicle to vehicle communication (V2V) and vehicle to infrastructure communication (V2I/I2V). In this protocol, the data are identified according to timeliness, on the base of the traditional V2V and V2I/I2V communication. If the time-sensitive data (V2V data) fail in transmission, the node transmits the data to the base station and let the base station cooperatively transmit the data with higher priority. This transmission scheme uses the large transmission range of base station in an effective manner. In this paper, the queueing models of the vehicles and base station are analyzed respectively by one-dimensional and two-dimensional Markov Chain, and the expressions of throughput, packet drop rate and delay are also derived. The simulation results show that this MAC protocol can improve the transmission efficiency of V2V communication and reduce the delay of V2V data without losing the system performance.

This paper describes an investigation into the validity of an automatic assessment method of the learner-build concept map by comparing it with two well-known manual methods. We have previously proposed the Kit-Build (KB) concept map framework where a learner builds a concept map by using only a provided set of components, known as the set “kit”. In this framework, instant and automatic assessment of a learner-build concept map has been realized. We call this assessment method the “Kit-Build method” (KB method). The framework and assessment method have already been practically used in classrooms in various schools. As an investigation of the validity of this method, we have conducted an experiment as a case study to compare the assessment results of the method with the assessment results of two other manual assessment methods. In this experiment, 22 university students attended as subjects and four as raters. It was found that the scores of the KB method had a very strong correlation with the scores of the other manual methods. The results of this experiment are one of evidence to show the automatic assessment of the Kit-Build concept map can attain almost the same level of validity as well-known manual assessment methods.