Slotted-waveguide array antennas are attractive because of their low-loss characteristics at high frequencies. Several types of slotted arrays whose polarization angles are inclined to the waveguide axis have been reported. In this paper, we propose a new type of slot array antenna on a rectangular coaxial line for minimizing the waveguide width. As opposed to a conventional waveguide, there is no “cut-off” concept in our proposal because the coaxial line is a transverse electromagnetic (TEM) line. Therefore it is possible to guide the wave even if the diameter of the line is much smaller than that of the waveguide. Moreover, the proposed antenna is a resonant slot array antenna that is based on standing-wave excitation and is thus different from traveling-wave antennas (such as a leaky coaxial cable (LCX)).

An injection locked coupled push-push 3-oscillators array using unilateral coupling circuits is proposed. The circuit consists of unit oscillators and coupling circuits. For the unit oscillator, a dual-band push-push oscillator which generates the fundamental signal (f0) and the second harmonic signal (2f0) is adopted. The output signal of the oscillator array is the second harmonic signal. The fundamental signal is used for the injection signal to synchronize oscillators. These adjoining unit oscillators are connected by the coupling circuits. The coupling circuit is composed of a buffer amplifier and a phase shifter. Due to the advantage of the push-push oscillator, the phase shift between the adjoining oscillators is twice as large as that of the phase shift in the coupling circuit. The oscillator array is designed in Ku-band. Three push-push oscillators are arrayed and include two coupling circuits which are designed and fabricated. The phase shift of 190.0 degrees between the adjoining unit oscillators is demonstrated.

Heterogeneous resources such as configurable logic blocks (CLBs), multiplier blocks (MULs) and RAM blocks (RAMs) where millions of logic gates are included have been added to field programmable gate arrays (FPGAs). The fixed-outline floorplanning used by the existing methods always has a big penalty item in the objective function to ensure all the modules are placed in the specified chip region, which maybe greatly degrade the wirelength. This paper presents a three-phase floorplanning method for heterogeneous FPGAs. First, a non-slicing free-outline floorplanning method is used to optimize the wirelength, however, in this phase, the satisfaction of resource requirements from functional modules might fail. Second, a min-cost-max-flow algorithm is used to tune the assignment of CLBs to functional modules, and assign contiguous regions to each module so that all the functional modules satisfy CLB requirements. Finally, the MULs and RAMs are allocated to modules by a network flow model. CLBs hold the maximum quantity among all the resources. Therefore, making a high utilization of them means an enhancement of the FPGA densities. The proposed method can improve the utilization of CLBs, hence, much larger circuits could be mapped to the same FPGA chip. The results show that about 7–85% wirelength reduction is obtained, and CLB utilization is improved by about 25%.

In most software development environments, time, computing and human resources needed to perform the testing of a component is strictly limited. In order to deal with such situations, this paper proposes a method of creating the best possible test suite (covering the maximum number of 3-tuples) within a fixed number of test cases.

This paper presents a novel CMOS readout circuit for satellite infrared time delay and integration (TDI) arrays. An integrate-while-read method is adopted, and a dead-pixel-elimination circuit for solving a critical problem of the TDI scheme is integrated within a chip. In addition, an adaptive charge capacity control method is proposed to improve the signal-to-noise ratio (SNR) for low-temperature targets. The readout circuit was fabricated with a 0.35-µm CMOS process for a 5004 mid-wavelength infrared (MWIR) HgCdTe detector array. Using the circuit, a 90% background-limited infrared photodetection (BLIP) is satisfied over a wide input range (∼200–330 K), and the SNR is improved by 11 dB for the target temperature of 200 K.

We have demonstrated switching characteristics in a wavelength switch based on multiple GaInAs/InP quantum wells. It consisted of straight arrayed waveguides with a linearly varying refractive index distribution. The refractive index can be changed via the thermo-optic (TO) effect. Using a Ti/Au thin-film heater to generate the TO effect, we realized four-port switching at four demultiplexed wavelengths. In addition, by changing the structure of the heater from rectangular to triangular, the power consumption for four-port switching was reduced by half.

Wavelength demultiplexed light switching is numerically calculated in the variable index arrayed waveguide. Wavelength demultiplexed light is switched in 4 output ports by changing the refractive index of variable index arrayed waveguide with 16 array waveguides. In the calculation, the phase differences in each arrayed waveguide, and the diffraction in the star coupler are considered. In 4 output ports switching, numerically calculated the refractive index changes of 16 array waveguides are numerically calculated to obtain the 24 switching pattern, and also calculated the crosstalk of each switching.

Ternary content addressable memory (TCAM) is becoming very popular for designing high-throughput forwarding engines on routers. However, TCAM has potential problems in terms of hardware and power costs, which limits its ability to deploy large amounts of capacity in IP routers. In this paper, we propose new hardware architecture for fast forwarding engines, called fast prefix search RAM-based hardware (FPS-RAM). We designed FPS-RAM hardware with the intent of maintaining the same search performance and physical user interface as TCAM because our objective is to replace the TCAM in the market. Our RAM-based hardware architecture is completely different from that of TCAM and has dramatically reduced the costs and power consumption to 62% and 52%, respectively. We implemented FPS-RAM on an FPGA to examine its lookup operation.

Traditional two-microphone noise reduction algorithms to deal with highly nonstationary directional noises generally use the direction of arrival or phase difference information. The performance of these algorithms deteriorate when diffuse noises coexist with nonstationary directional noises in realistic adverse environments. In this paper, we present a two-channel noise reduction algorithm using a spatial information-based speech estimator and a spatial-information-controlled soft-decision noise estimator to improve the noise reduction performance in realistic non-stationary noisy environments. A target presence probability estimator based on Bayes rules using both phase difference and magnitude squared coherence is proposed for soft-decision of noise estimation, so that they can share complementary advantages when both directional noises and diffuse noises are present. Performances of the proposed two-microphone noise reduction algorithm are evaluated by noise reduction, log-spectral distance (LSD) and word recognition rate (WRR) of a distant-talking ASR system in a real room's noisy environment. Experimental results show that the proposed algorithm achieves better noises suppression without further distorting the desired signal components over the comparative dual-channel noise reduction algorithms.

Given an odd prime q and an integer m ≤ q, an array-based parity-check matrix H(m,q) can be constructed for a quasi-cyclic low-density parity-check (LDPC) code C(m,q). For m=4 and q ≥ 11, we prove the stopping distance of H(4,q) is 10, which is equal to the minimum Hamming distance of the associated code C(4,q). In addition, a tighter lower bound on the stopping distance of H(m,q) is also given for m > 4 and q ≥ 11.

In this paper, we designed and fabricated large scale micro-light-emitting-diode (LED) arrays and silicon driver for single chip device for realizing as prototypes of heterogeneous optoelectronic integrated circuits (OEICs). The large scale micro-LED arrays were separated by a dry etching method from mesa structure to 16,384 pixels of 128 128, each with a size of 15 µm in radius. Silicon driver was designed the additional bonding pad on each driving transistor for bonding with micro-LED arrays. Fabricated micro-LED arrays and driver were flip-chip bonded using anisotropic conductive adhesive.

We developed a flexible-logic-gate single-electron device (SED) in which logic functions can be selected by changing the voltage applied to the control gate. It consists of an array of nanodots with multiple inputs and multiple outputs. Since the gate electrodes couple capacitively to the many dots underneath, complicated characteristics depending on the combination of the gate voltages yield a selectable logic gate when some of the gate electrodes are used as control gates. One of the important issues is how to design the arrangement of nanodots and gate electrodes. In this study, we fabricated a Si nanodot array with two simple input gates and two output terminals, in which each gate was coupled to half of the nanodot array. Even though the device had a very simple input-gate arrangement and just one control gate, we could create a half-adder function through the use of current maps as functions of the input gate voltages. We found that the nanodots evenly coupled capacitively to both input gates played an important role in getting a basic set of logic functions. Moreover, these results guarantee that a more complicated input-gate structure, in which each gate evenly couples many nanodots, will yield more complicated functions.

This paper describes a method for estimating Direction Of Arrival (DOA) of multiple sound sources in full azimuth with three microphones. Estimating DOA with paired microphone arrays creates imaginary sound sources because of time delay of arrival (TDOA) being identical between real and imaginary sources. Imaginary sound sources can create chronic problems in multiple Sound Source Localization (SSL), because they can be localized as real sound sources. Our proposed approach is based on the observation that each microphone array creates imaginary sound sources, but the DOA of imaginary sources may be different depending on the orientation of the paired microphone array. With the fact that a real source would always be localized in the same direction regardless of the array orientation, we can suppress the imaginary sound sources by minimum filtering based on Steered Response Power – Phase Transform (SRP-PHAT) method. A set of experiments conducted in a real noisy environment showed that the proposed method was accurate in localizing multiple sound sources.

In this paper, cell searching and direction-of-arrival (DoA) estimation methods are proposed for mobile relay stations with a uniform linear arrays in OFDM-based cellular systems. The proposed methods can improve the performance of cell searching and DoA estimation, even when there exist symbol timing offsets among the signals received from adjacent base stations and Doppler frequency shifts caused by the movement of the mobile relay station. The performances and computational complexities of the proposed cell searching and DoA estimation methods are evaluated by computer simulation under a mobile WiMAX environment.

This paper proposes a method of designing EM absorber panels under oblique incident waves. TM and TE wave reflection characteristics of the absorber panel show its anisotropy under oblique incidence. By using the wire array sheet proposed this paper, TM and TE reflection coefficients in oblique incidence can be matched at almost the same frequency range.

A new near-field source localization algorithm based on a uniform linear array was proposed. The proposed algorithm estimates each parameter separately but does not need pairing parameters. It can be divided into two important steps. The first step is bearing-related electric angle estimation based on the ESPRIT algorithm by constructing a special cumulant matrix. The second step is the other electric angle estimation based on the 1-D MUSIC spectrum. It offers much lower computational complexity than the traditional near-field 2-D MUSIC algorithm and has better performance than the high-order ESPRIT algorithm. Simulation results demonstrate that the performance of the proposed algorithm is close to the Cramer-Rao Bound (CRB).

Short-range Multiple-Input-Multiple-Output (SR-MIMO) transmission is an effective technique for achieving high-speed and short-range wireless communication. With this technique, however, the optimum aperture size of array antennas grows when the transmission distance is increased. Thus, antenna miniaturization is an important issue in SR-MIMO. In this paper, we clarify the effectiveness of using dual-polarized planar antennas as a means of miniaturizing SR-MIMO array antennas by measurements and analysis of MIMO transmission characteristics. We found that even in SR-MIMO transmission, the use of dual-polarized transmission enables higher channel capacity. Dual-polarized antennas can reduce by two thirds the array area that is needed to obtain the same channel capacity. For a transmission distance of two wavelengths, the use of a dual-polarized antenna improved the channel capacity by 26 bit/s/Hz while maintaining the same number of transmitters and receivers and the same antenna aperture size. Moreover, dual-polarized SR-MIMO has a further benefit when zero-forcing (ZF) reception without transmit beamforming is adopted, i.e., it effectively simplifies hardware configuration because it can reduce spatial correlation even in narrow element spacing. In this work, we confirmed that the application of dual-polarization to SR-MIMO is an effective way to both increase channel capacity and enhance transceiver simplification.

A broadband microstrip comb-line antenna using a corporate feeding system was developed. The antenna was composed of four colinearly-arranged comb-line antennas with traveling-wave excitation fed by a parallel-feeding circuit of tournament configuration. The total phase deviation due to frequency change became one fourth of the ordinary series feeding from the end of the antenna. Furthermore, the terminations of the inner two comb-lines were connected at the overall center of the developed antenna. Therefore, the narrowband matching elements are not necessary and the amplitude deviation of the aperture distribution for input from one side due to frequency change is compensated by deviation for input from the other side. Broad bandwidth can be expected by using the proposed configuration. The proposed antenna was designed at 76.5 GHz. The effect of the proposed feeding-circuit for broadband operation was confirmed by comparing the measured performances of the antennas fed by other feeding circuits; the end feeding, the center feeding and the ordinary corporate feeding. The bandwidth of the proposed corporate feeding antenna with the center connecting was approximately 14% and 7% wider than the antennas of the center feeding and of the ordinary corporate feeding, respectively.

Let T be a text of length n and P be a pattern of length m, both strings over a fixed finite alphabet. The Pattern Matching with Swaps problem is to find all occurrences of P in T if adjacent pattern characters can be swapped. In the Approximate Pattern Matching problem with Swaps, one seeks for every text location with a swapped match of P, the number of swaps necessary to obtain a match at the location. In this paper we provide the first off-line solution for the swap matching problem and the approximate pattern matching problem with swaps. We present a new data-structure called a Swap-transforming Tree. And we give a precise upper-bond of the number of the swapped versions of a pattern. By using the swap-transforming tree, we can solve both problems in time O(λmlog2 n) on an O(nHk) bits indexing data structure. Here λ is a constant. Our solution is more effective when the pattern is short.

Equivalent Transmission Path (ETP) model-based BER map method was proved to be used in fast estimating Bit Error Rate (BER) of Single-Input Single-Output Orthogonal Frequency Division Multiplexing (SISO-OFDM) system, where the delay spreading exceeds the guard interval. In this paper, we propose a method for evaluating transmission characteristics of Single-Input Multiple-Output Orthogonal Frequency Division Multiplexing (SIMO-OFDM) system with application to maximum ratio combining diversity at the reception. The simulation results show that the proposed approximation method is able to be used in estimating trasmission characteristics with high accuracy not only for SISO-OFDM system but also for SIMO-OFDM system.