The rotating element electric field vector (REV) method is a classical measurement technique for phased array calibration. Compared with other calibration methods, it requires only power measurements. Thus, the REV method is more reliable for operating phased array calibration systems. However, since the phase of each element must be rotated from 0 to 2π, the conventional REV method requires a large number of measurements. Moreover, the power of composite electric field vector doesn't vary significantly because only a single element's phase is rotated. Thus, it can be easily degraded by the receiver noise. A simplified REV method combined with Hadamard group division is proposed in this paper. In the proposed method, only power measurements are required. All the array elements are divided into different groups according to the group matrix derived from the normalized Hadamard matrix. The phases of all the elements in the same group are rotated at the same time, and the composite electric field vector of this group is obtained by the simplified REV method. Hence, the relative electric fields of all elements can be obtained by a matrix equation. Compared with the conventional REV method, the proposed method can not only reduce the number of measurements but also improve the measurement accuracy under the particular range of signal to noise ratio(SNR) at the receiver, especially under low and moderate SNRs.
Heemang SONG Seunghoon CHO Kyung-Jin YOU Hyun-Chool SHIN
In this paper, we propose an automotive radar sensor compensation method improving direction of arrival (DOA) and preventing target split tracking. Amplitude and phase mismatching and mutual coupling between radar sensor arrays cause an inaccuracy problem in DOA estimation. By quantifying amplitude and phase distortion levels for each angle, we compensate the sensor distortion. Applying the proposed method to Bartlett, Capon and multiple signal classification (MUSIC) algorithms, we experimentally demonstrate the performance improvement using both experimental data from the chamber and real data obtained in actual road.
Pei CHEN Dexiu HU Yongjun ZHAO Chengcheng LIU
Aiming at solving the performance degradation caused by the covariance matrix mismatch in wideband beamforming for conformal arrays, a novel adaptive beamforming algorithm is proposed in this paper. In this algorithm, the interference-plus-noise covariance matrix is firstly reconstructed to solve the desired signal contamination problem. Then, a sparse reconstruction method is utilized to reduce the high computational cost and the requirement of sampling data. A novel cost function is formulated by the focusing matrix and singular value decomposition. Finally, the optimization problem is efficiently solved in a second-order cone programming framework. Simulation results using a cylindrical array demonstrate the effectiveness and robustness of the proposed algorithm and prove that this algorithm can achieve superior performance over the existing wideband beamforming methods for conformal arrays.
Jian YANG Fangfang FAN Parastoo TAGHIKHANI Abbas VOSOOGH
This paper presents a new form of gap waveguide technology - the half-height-pin gap waveguide. The gap waveguide technology is a new transmission line technology introduced recently, which makes use of the stopband of wave propagation created by a pair of parallel plates, one PEC (perfect electric conductor) and one PMC (perfect magnetic conductor), with an air gap in between less than a quarter of the wavelength at operation frequency. Applying this PEC/PMC gap plate structure to ridged waveguides, rectangular hollow waveguides and microstrip lines, we can have the ridged gap waveguides, groove gap waveguides and inverted gap waveguide microstrip lines, respectively, without requiring a conductive or galvanic contact between the upper PEC and the lower PMC plates. This contactless property of the gap waveguide technology relaxes significantly the manufacturing requirements for devices and antennas at millimeter wave frequencies. PMC material does not exist in nature, and an artificial PMC boundary can be made by such as periodic pin array with the pin length about a quarter wavelength. However, the quarter-wavelength pins, referred to as the full-height pins, are often too long for manufacturing. In order to overcome this difficulty, a new half-height-pin gap waveguide is introduced. The working principles and Q factors for the half-height-pin gap waveguides are described, analyzed and verified with measurements in this paper. It is concluded that half-height-pin gap waveguides have similar Q factors and operation bandwidth to the full-height-pin gap waveguides. As an example of the applications, a high gain planar array antenna at V band by using the half-height-pin gap waveguide has been designed and is presented in the paper with a good reflection coefficient and high aperture efficiency.
Hiroyuki DEGUCHI Daichi HIGASHI Hiroki YAMADA Shogo MATSUMOTO Mikio TSUJI
This paper proposes a genetic algorithm (GA) based design method for arbitrarily-shaped resonant elements that offer enhanced reflectarray antenna performance. All elements have the specified phase property over the range of 360°, and also have dual-polarization and low cross-polarization properties for better reflectarray performance. In addition, the proposal is suitable for linear-to-circular polarization conversion elements. Thus, polarizer reflectarray elements are also presented in this paper. The proposed elements are validated using both numerical simulations and experiments.
Zhi ZHENG Yuxuan YANG Wen-Qin WANG Guangjun LI Jiao YANG Yan GE
This paper proposes a novel method for two-dimensional (2-D) direction-of-arrival (DOA) estimation of multiple signals employing a sparse L-shaped array structured by a sparse linear array (SLA), a sparse uniform linear array (SULA) and an auxiliary sensor. In this method, the elevation angles are estimated by using the SLA and an efficient search approach, while the azimuth angle estimation is performed in two stages. In the first stage, the rough azimuth angle estimates are obtained by utilizing a noise-free cross-covariance matrix (CCM), the estimated elevation angles and data from three sensors including the auxiliary sensor. In the second stage, the fine azimuth angle estimates can be achieved by using the shift-invariance property of the SULA and the rough azimuth angle estimates. Without extra pair-matching process, the proposed method can achieve automatic pairing of the 2-D DOA estimates. Simulation results show that our approach outperforms the compared methods, especially in the cases of low SNR, snapshot deficiency and multiple sources.
Hideki KIRINO Kazuhiro HONDA Kun LI Koichi OGAWA
A new Waffle-iron Ridge Guide (WRG) structure that has the ability to control both wavelength and impedance is proposed. With the proposed structure, not only can the wavelength be controlled over a wide range for both fast- and slow-waves in free space but the impedance can also be controlled. These features can improve the performance of array antennas in terms of reducing grating lobes and side lobes. In this paper, we discuss and evaluate a design scheme using equivalent circuits and EM-simulation. This paper also discusses how the conductivity and dielectric loss in the WRG affect the total gain of the array antenna.
Yasuaki OHIRA Takahiro MATSUMOTO Hideyuki TORII Yuta IDA Shinya MATSUFUJI
In this paper, we propose a new structure for a compact matched filter bank (MFB) for an optical zero-correlation zone (ZCZ) sequence set with Zcz=2z. The proposed MFB can reduces operation elements such as 2-input adders and delay elements. The number of 2-input adders decrease from O(N2) to O(N log2 N), delay elements decrease from O(N2) to O(N). In addition, the proposed MFBs for the sequence of length 32, 64, 128 and 256 with Zcz=2,4 and 8 are implemented on a field programmable gate array (FPGA). As a result, the numbers of logic elements (LEs) of the proposed MFBs for the sequences with Zcz=2 of length 32, 64, 128 and 256 are suppressed to about 76.2%, 84.2%, 89.7% and 93.4% compared to that of the conventional MFBs, respectively.
Yasunari MORI Takayoshi YUMII Yumi ASANO Kyouji DOI Christian N. KOYAMA Yasushi IITSUKA Kazunori TAKAHASHI Motoyuki SATO
This paper presents a calibration method for RF switch channels of a near-range multistatic linear array radar. The method allows calibration of the channel transfer functions of the RF switches and antenna transfer functions in frequency domain data, without disconnecting the antennas from the radar system. In addition, the calibration of the channels is independent of the directivities of the transmitting and receiving antennas. We applied the calibration method to a 3D imaging step-frequency radar system at 10-20GHz suitable for the nondestructive inspection of the walls of wooden houses. The measurement range of the radar is limited to 0-240mm, shorter than the antenna array length 480mm. This radar system allows acquiring 3D imaging data with a single scan. Using synthetic aperture radar processing, the structural health of braces inside the walls of wooden houses can be evaluated from the obtained 3D volume images. Based on experiment results, we confirmed that the proposed calibration method significantly improves the subsurface 3D imaging quality. Low intensity ghost images behind the brace target were suppressed, deformations of the target in the volume image were rectified and errors the range distance were corrected.
Di YAO Xin ZHANG Qiang YANG Weibo DENG
An improved beamformer, which uses joint estimation of the reconstructed interference-plus-noise (IPN) covariance matrix and array steering vector (ASV), is proposed. It can mitigate the problem of performance degradation in situations where the desired signal exists in the sample covariance matrix and the steering vector pointing has large errors. In the proposed method, the covariance matrix is reconstructed by weighted sum of the exterior products of the interferences' ASV and their individual power to reject the desired signal component, the coefficients of which can be accurately estimated by the compressed sensing (CS) and total least squares (TLS) techniques. Moreover, according to the theorem of sequential vector space projection, the actual ASV is estimated from an intersection of two subspaces by applying the alternating projection algorithm. Simulation results are provided to demonstrate the performance of the proposed beamformer, which is clearly better than the existing robust adaptive beamformers.
Yasunori SUZUKI Takana KAHO Kei SATOH Hiroshi OKAZAKI Maki ARAI Yo YAMAGUCHI Shoichi NARAHASHI Hiroyuki SHIBA
This paper presents an extremely low-profile front-end configuration for a base station at quasi-millimeter wave band. It consists of integrated modules of patch antennas and substrate integrated waveguide filters using two printed circuit boards, and transmitter modules using compact GaAs pHEMT three-dimensional monolithic millimeter-wave integrated circuits. The transmitter modules are located around the integrated modules. This is because the proposed front-end configuration can attain extremely low profile, and band-pass filtering performance at quasi-millimeter wave band. As a demonstration of the proposed configuration, 26-GHz-band 4-by-4 elements front-end module is fabricated and tested. The fabricated module has the thickness of about 1 cm, while that offers the attenuation of more than 30 dB with 2 GHz offset from 26 GHz. The proposed configuration can provide base station that can be effective in offering sub-millimeter wave and millimeter-wave bands broadband services for 5G mobile communications systems.
Kunihiro FUJIYOSHI Takahisa IMANO
Photo Diode Array (PDA) is the key semiconductor component expected to produce specified output voltage in photo couplers and photo sensors when the light is on. PDA partitioning problem, which is to design PDA, is: Given die area, anode and cathode points, divide the area into N cells, with identical areas, connected in series from anode to cathode. In this paper, we first make restrictions for the problem and reveal the underlying properties of necessary and sufficient conditions for the existence of solutions when the restrictions are satisfied. Then, we propose a method to solve the problem using recursive algorithm, which can be guaranteed to obtain a solution in polynomial time.
Yusuke MATSUSHITA Hayate OKUHARA Koichiro MASUYAMA Yu FUJITA Ryuta KAWANO Hideharu AMANO
Body biasing can be used to control the leakage power and performance by changing the threshold voltage of transistors after fabrication. Especially, a new process called Silicon-On-Thin Box (SOTB) CMOS can control their balance widely. When it is applied to a Coarse Grained Reconfigurable Array (CGRA), the leakage power can be much reduced by precise bias control with small domain size including a small number of PEs. On the other hand, the area overhead for separating power domain and delivering a lot of wires for body bias voltage supply increases. This paper explores the grain of domain size of an energy efficient CGRA called CMA (Cool Mega Array). By using Genetic Algorithm based body bias assignment method, the leakage reduction of various grain size was evaluated. As a result, a domain with 2x1 PEs achieved about 40% power reduction with a 6% area overhead. It has appeared that a combination of three body bias voltages; zero bias, weak reverse bias and strong reverse bias can achieve the optimal leakage reduction and area overhead balance in most cases.
Zhihao ZHONG Jianhua PENG Kaizhi HUANG
In order to satisfy the very high traffic demand in crowded hotspot areas and realize adequate security in future fifth-generation networks, this paper studies physical-layer security in the downlink of a two-tier ultra dense heterogeneous network, where a ubiquitous array formed by ultra dense deployed small-cells surrounds a macrocell base station. In this paper, the locations of legitimate users and eavesdroppers are drawn from Poisson point processes. Then, the cumulative distribution functions of the receive signal-to-interference-plus-noise ratio for legitimate users and eavesdroppers are derived. Further, the average secrecy rate and secrecy coverage probability for each tier as well as for the whole network are investigated. Finally, we analyze the influences on secrecy performance caused by eavesdropper density, transmit power allocation ratio, antenna number allocation ratio, and association area radius.
Bo YANG Tomohiko MITANI Naoki SHINOHARA
We developed a 5.8 GHz power-variable phase-controlled magnetron (PVPCM) which controls the phase of magnetron output by a phase shifter and controls the power by the anode current of the magnetron. This method is different from the previous 2.45 GHz phase-controlled magnetron which utilizes an injection method and a phase locked loop by the anode current, since the frequency of 5.8 GHz magnetron hardly changes with the anode current. Our experiments show that the developed 5.8 GHz PVPCM had a variable output power with 1% power stability from 160 W to 329 W, the phase accuracy was nearly ±1°, and the response time was less than 100 µs. Stable output power, high phase-controlled accuracy, and fast response speed microwave sources based on the PVPCMs are suitable for phased array system for wireless power transfer.
Hideyuki NAKAMIZO Shintaro SHINJO Koji TSUTSUMI Satoshi YAMAGUCHI Hideharu YOSHIOKA Akihiro OKAZAKI Akinori TAIRA Kenichi TAJIMA
In order to meet various requirements for the 5th generation mobile communication, a high SHF wideband massive-MIMO system has been widely studied which offers wide system bandwidth and high spectral efficiency. A hybrid beamforming configuration which combines analog beamforming by APAA (Active Phased Array Antenna) and digital MIMO signal processing is one of the promising approaches for reducing the complexity and power consumption of the high SHF wideband massive-MIMO system. In order to realize the hybrid beamforming configuration in high SHF band, small size, low power consumption and precise beam forming over the wide-band frequency range are strongly required for RF frontend which constitutes analog beam former. In this paper, a compact RF frontend module for high SHF wideband 5G small cell base station is proposed. This RF frontend module is prototyped. Various key components of the RF frontend module are fabricated in 15GHz band, and measured results show that high RF performances are able to meet the requirements of RF frontend.
Kouhei SUZUKI Hideya SO Daisuke GOTO Yoshinori SUZUKI Fumihiro YAMASHITA Katsuya NAKAHIRA Kiyoshi KOBAYASHI Takatoshi SUGIYAMA
This paper introduces distributed array antenna (DAA) systems that offer high antenna gain. A DAA consists of several small antennas with improved antenna gain. This paper proposes a technique that suppresses the off-axis undesired radiation and compensates the time delay by combining signal processing with optimization of array element positioning. It suppresses the undesired radiation by compensating the delay timing with high accuracy and deliberately generating the inter-symbol interference (ISI) in side-lobe directions. Computer simulations show its effective suppression of the equivalent isotropic radiated power (EIRP) pattern and its excellent BER performance.
Koji TSUTSUMI Takaya MARUYAMA Wataru YAMAMOTO Takanobu FUJIWARA Tatsuya HAGIWARA Ichiro SOMADA Eiji TANIGUCHI Mitsuhiro SHIMOZAWA
A 15GHz-band 4-channel transmit/receive RF core-chip is presented for high SHF wide-band massive MIMO in 5G. In order to realize small RF frontend for 5G base stations, both 6bit phase shifters (PS) and 0.25 dB resolution variable gain amplifiers (VGA) are integrated in TX and RX paths of 4-channels on the chip. A PS calibration technique is applied to compensate the error of 6bit PS caused by process variations. A common gate current steering topology with tail current control is used for VGA to enhance the gain control accuracy. The 15GHz-band RF core-chip fabricated in 65 nm CMOS process achieved phase control error of 1.9deg. rms., and amplitude control error of 0.23 dB. rms.
Yuanfeng SHE Masanobu HIROSE Yuto KATO Takayuki ISHIZONE Satoru KUROKAWA Shinya IWASAWA Sintaro ARATA
This article proposes a simply structured transverse slot linear array antenna with a low cross-polarization in X band on a quasi-TEM (transverse electromagnetic) mode waveguide. The fabrication technology of this antenna is very simple and suitable for mass production. A center fed linear slot array has been designed and measured. The quasi-TEM wave is propagating in the conventional waveguide with dielectrics at sidewalls. The simulation and the measurement results show that the baffle plates enhance the gain and reduce the beamwidth effectively. The uncertainties of the electric properties of the dielectric and fabrication errors are also discussed.
Kotoko FURUYA Takayoshi HIRASAWA Masayuki OISHI Shigeyuki AKIBA Jiro HIROKAWA Makoto ANDO
This paper presents a novel 60 GHz-band photonic-integrated array-antenna and module for radio-over-fiber (RoF)-based beam forming. An integrated photonic array-antennas (IPA), where eight photodiodes and 4×2 arrayed patch-antenna are integrated in a single board, is actually fabricated, and 3.5-Gbit/s QPSK digital signal transmission with beam forming of the IPA is experimentally demonstrated. In addition, a novel 60-GHz compact antenna module is proposed and fabricated for increasing the number of antenna elements and flexibility creating various beam patterns. The feasibility of beam forming operation for the proposed antenna module is confirmed by a 60-GHz RoF transmission experiment. The capability of detecting the mobile terminal direction, which is one of the indispensable functions for actual environment, is also studied. The obtained results in this paper will be useful for designing future radio access networks based on RoF transmission technology.