This paper proposes reflection and transmission control panels using artificially designed materials. As the artificially designed material, finite- and infinite-length metal wire array sheets are used here. Laminated structures consisting of the metal wire array sheets and dielectric material are proposed. Reflection and transmission characteristics of these structures can be controlled by changing the metal wire parameters such as wire length, spacing gaps between the wires, and the dielectric material's thickness and relative permittivity. The reflection and transmission characteristics of the laminated structures are evaluated by measurements in free space and by transmission line theory.

In order to efficiently drive a low-power DC motor using microwave power transfer (MPT), a compact power-receiving device is developed, which consists of a rectenna array and an improved DC-DC converter with constant input resistance characteristics. Since the conversion efficiency of the rectenna is strongly affected by the output load, it is difficult to efficiently drive a dynamic load resistance device such as DC motor. Using both continuous-wave (CW) and pulsed-wave MPT, experiments are carried out on driving the DC motor whose load resistance is varying from 36 to 140 Ω. In the CW case, the measured overall efficiency of the power-receiving device is constant over 50% for the power density of 0.25 to 2.08 mW/cm2. In particular, the overall efficiency is 62%, 70.8% for the power density of 0.25, 0.98 mW/cm2 where the received power of the single antenna is 13, 50 mW, respectively. In the pulsed-wave case, the measured overall efficiency is over 44% for a duty ratio of 0.2 to 1 for the power density of 0.98 mW/cm2.

This paper presents a new way to classify different radiation sources by the parameter of directivity, which is a characteristic parameter of electromagnetic radiation sources. The parameter can be determined from measurements of the electric field intensity radiating in all directions in space. We develop three basic antenna models, which are for 3GHz operation, and set 125,000 groups of cube receiving arrays along the main lobe of their radiation patterns to receive the data of far field electric intensity in groups. Then the Back Propagation (BP) neural network and the Support Vector Machine (SVM) method are adopted to analyze training data set, and build and test the classification model. Owing to the powerful nonlinear simulation ability, the SVM method offers higher classification accuracy than the BP neural network in noise environment. At last, the classification model is comprehensively evaluated in three aspects, which are capability of noise immunity, F1 measure and the normalization method.

This paper proposes a novel blind adaptive array scheme with subcarrier transmission power assignment (STPA) for spectrum superposing in cognitive radio networks. The Eigenvector Beamspace Adaptive Array (EBAA) is known to be one of the blind adaptive array algorithms that can suppress inter-system interference without any channel state information (CSI). However, EBAA has difficulty in suppressing interference signals whose Signal to Interference power Ratio (SIR) values at the receiver are around 0dB. With the proposed scheme, the ST intentionally provides a level difference between subcarriers. At the receiver side, the 1st eigenvector of EBAA is applied to the received signals of the subcarrier assigned higher power and the 2nd eigenvector is applied to those assigned lower power. In order to improve interference suppression performance, we incorporate Beamspace Constant Modulus Algorithm (BSCMA) into EBAA (E-BSCMA). Additionally, STPA is effective in reducing the interference experienced by the primary system. Computer simulation results show that the proposed scheme can suppress interference signals received with SIR values of around 0dB while improving operational SIR for the primary system. It can enhance the co-existing region of 2 systems that share a spectrum.

The present paper proposes a method for simultaneously estimating the direction of arrival (DOA) and delay of multipath signals through the virtual array reception of broadband signals. In order to confirm the principles behind the proposed method, a broadband signal of 42MHz, equivalent to seven adjacent TV channels being transmitted from the Tokyo Skytree, was acquired and stored in a personal computer as the reception signal, which acts as reference signal. In addition, a multipath signal with DOA and delay was generated using a personal computer. Signal processing revealed that DOA and delay could be identified correctly. Finally, a multipath propagation analysis is conducted for an actual outdoor propagation environment as a demonstration of the proposed method.

A rotating shaft with attached sensors is wrapped in a two-dimensional waveguide sheet through which the data and power are wirelessly transmitted. A retrodirective transponder array affixed to the sheet beamforms power to the moving sensor to eliminate the need for a battery. A universal on-sheet reference scheme is proposed for calibrating the transponder circuit delay variation and eliminating a crystal oscillator from the sensor. A base signal transmitted from the on-sheet reference device is used for generating the pilot signal transmitted from the sensor and the power signal transmitted from the transponder. A 0.18-µm CMOS transponder chip and the sheet with couplers were fabricated. The coupler has three resonant frequencies used for the proposed system. The measured propagation gain of the electric field changes to less than ±1.5dB within a 2.0-mm distance between the coupler and the sheet. The measured power transmission efficiency with beamforming is 23 times higher than that without it. Each transponder outputs 1W or less for providing 3mW to the sensor.

Perfect arrays are widely applied to high-dimensional communications, time-frequency-coding, spatial correlation or map matching, built-in tests of VLSI-circuits, radar, and so on. The letter investigates perfect arrays over the 8-QAM+ constellation, and two constructions for yielding such arrays are presented. Furthermore, the family size of the proposed arrays is determined as well.

Monopulse is a classical technique for radar angle estimation and still adopted for fast angle estimation in phased array antenna. The classical formula can be applied to a 2-dimentional phased array antenna if two conditions---the unbiasedness and the independence of the azimuth and the elevation estimate---are satisfied. However, if the sum and difference beams are adapted to suppress the interference under jamming condition, they can be severely distorted. Thus the difference beams become highly correlated and violate the conditions. In this paper, we show the numerical implementation of the generalized monopulse estimation using the distorted and correlated beams, especially for a subarray configured antenna. Because we use the data from the measured subarray patterns rather than the mathematical model, this numerical method can be easily implemented for the complex array configuration and gives good performance for the uncertainty of the real system.

In this paper, two receive beamforming techniques (Method 1 and Method 2) are proposed for a mobile station (MS) with multiple antenna arrays in an OFDM-based millimeter-wave (mm-wave) cellular communication system. Since the MS in mm-wave cellular communication requires fast processing due to its frequent movement and rotation, a receive beamforming technique with reduced computation complexity and processing time is proposed in Method 2. Of particular interest, estimation techniques for 2-dimensional (2D) direction-of-arrivals (DoAs) corresponding to each cell ID are proposed for uniform circular arrays (UCAs) and uniform rectangular arrays (URAs). Also, a cell selection technique for MSs with multiple antenna arrays is described that use the candidate cell IDs and parameters estimated for all antenna arrays to provide combining gain in addition to array gain in multipath channels. The proposed beamforming techniques are evaluated by computer simulation using a simple model of amm-wave cellular communication system with 3-dimensional spatial channel model (3D SCM).

Recently, array speaker products have received attention in the field of consumer electronics, and control technologies for arrayed speaker units, including beamforming and wave field synthesis (WFS), have been developed for various purposes. An important application of these algorithms is focused source reproduction. The focused source reproduction capability is strongly coupled with the array length. The array length is a very important design factor in consumer products, but it is very short in home entertainment systems, compared with ideal WFS systems or theater speaker systems. Therefore, a well-defined measure for the maximum focusing range is necessary for designing an array speaker product. In this paper, a maximum focusable range measure is proposed and is analyzed by simulation of a small array speaker. The analysis results show that the proposed maximum focusable range has properties strongly related to the capability for focused source reproduction.

A processing system with multiple field programmable gate array (FPGA) cards is described. Each FPGA card can interconnect using six I/O (up, down, left, right, front, and back) terminals. The communication network among FPGAs is scalable according to user design. When the system operates multi-dimensional applications, transmission efficiency among FPGA improved through user-adjusted dimensionality and network topologies for different applications. We provide a fast and flexible circuit configuration method for FPGAs of a multi-dimensional FPGA array. To demonstrate the effectiveness of the proposed method, we assess performance and power consumption of a circuit that calculated 3D Poisson equations using the finite difference method.

We propose a novel phased array-fed dual-reflector antenna that reduces performance degradation caused by multiple reflection. The marked feature of the proposed configuration is that different reflector profiles are employed for the two orthogonal directions. The reflector profile in the beam-scanning section (vertical section) is set to an imaging reflector configuration, while the profile in the orthogonal non-beam-scanning section (horizontal section) is set to a ring-focus Cassegrain antenna configuration. In order to compare the proposed antenna with the conventional antenna in which multiple reflection was problematic, we designed a prototype antenna of the same size, and verified the validity of the proposed antenna. The results of the verification were that the gain in the designed central frequency increased by 0.4 dB, and the ripple of the gain frequency properties that was produced by multiple reflection was decreased by 1.1,dB. These results demonstrated the validity of the proposed antenna.

We propose a synthesis method of nested loops into parallelized circuits by integrating the polyhedral optimization, which is a state-of-the-art technique in the field of software, into high-level synthesis. Our method constructs circuits equipped with multiple processing elements (PEs), using information generated by the polyhedral optimizing compiler. Since multiple PEs cannot concurrently access the off-chip RAM, a method for constructing on-chip buffers is also proposed. Our buffering method reduces the off-chip RAM access conflicts and further enables burst accesses and data reuses. In our experimental result, the buffered circuits generated by our method are 8.2 times on average and 26.5 times at maximum faster than the sequential non-buffered ones, when each of the parallelized circuits is configured with eight PEs.

In this paper, we propose a new structure for a compact matched filter bank for a mutually orthogonal zero-correlation zone (MO-ZCZ) sequence set consisting of ternary sequence pairs obtained by Hadamard and binary ZCZ sequence sets; this construction reduces the number of two-input adders and delay elements. The matched filter banks are implemented on a field-programmable gate array (FPGA) with 51,840 logic elements (LEs). The proposed matched filter bank for an MO-ZCZ sequence set of length 160 can be constructed by a circuit size that is about 8.6% that of a conventional matched filter bank.

In this paper, we investigate the minimum-weight codewords of array LDPC codes C(m,q), where q is an odd prime and m ≤ q. Using some analytical approaches, the lower bound on the number of minimum-weight codewords of C(m,q) given by Kaji (IEEE Int. Symp. Inf. Theory, June/July 2009) is proven to be tight for m = 4 and q > 19. In other words, C(4,q) has 4q2(q-1) minimum-weight codewords for all q > 19. In addition, we show some interesting universal properties of the supports of generators of minimum-weight codewords of the code C(4,q)(q > 19).

This paper presents a spatial division (SD) transmission method based on two-ray fading that dispenses with the high signal processing cost of multiple-input and multiple-output (MIMO) detection and antennas with narrow beamwidth. We show the optimum array geometries as functions of the transmission distance for providing a concrete array design method. Moreover, we clarify achievable channel capacity considering reflection coefficients that depend on the polarization, incident angle, and dielectric constant. When the ground surface is conductive, for two- and three-element arrays, channel capacity is doubled and tripled, respectively, over that of free space propagation. We also clarify the application limit of this method for a dielectric ground by analyzing the channel capacity's dependency on the dielectric constant. With this method, increased channel capacity by SD transmission can be obtained merely by placing antennas of wireless transceiver sets that have only SISO (single-input and single-output) capability in a two-ray propagation environment. By using formulations presented in this paper for the first time and adding discussions on the adoption of polarization multiplexing, we clarify antenna geometries of SD transmission systems using polarization multiplexing for up to six streams.

In this paper, an adaptive expansion strategy (AES) is proposed for multiple-input/multiple-output (MIMO) detection in the presence of circular signals. By exploiting channel properties, the AES classifies MIMO channels into three types: excellent, average and deep fading. To avoid unnecessary branch-searching, the AES adopts single expansion (SE), partial expansion (PE) and full expansion (FE) for excellent channels, average channels and deep fading channels, respectively. In the PE, the non-circularity of signal is exploited, and the widely linear processing is extended from non-circular signals to circular signals by I (or Q) component cancellation. An analytical performance analysis is given to quantify the performance improvement. Simulation results show that the proposed algorithm can achieve quasi-optimal performance with much less complexity (hundreds of flops/symbol are saved) compared with the fixed-complexity sphere decoder (FSD) and the sphere decoder (SD).

This paper presents the design and radiation properties of a linearly polarized radial line microstrip antenna array (RL-MSAA) with U-slot circular microstrip antennas. A circular microstrip antenna (C-MSA) with U-shaped slot is used as a radiation element of the RL-MSAA. Radiation phase of the U-slot C-MSA is controlled by tuning the radius of the C-MSA and dimensions of the U-slot on the C-MSA; therefore, the desired phase distribution of the RL-MSAA can be realized. In this paper, a linearly polarized RL-MSAA with three concentric rows of C-MSAs at a spacing of 0.65 wavelengths is designed for 12GHz operation. In order to realize uniform phase distribution, the U-slot C-MSAs are arranged for inner two rows and normal C-MSAs are arranged for the termination row. Validity of the linearly polarized RL-MSAA with the U-slot C-MSAs for radiation phase control is demonstrated by simulation and measurement.

Sound field reproduction systems seek to realistically convey 3D spatial audio by re-creating the sound pressure inside a region enclosing the listener. High-order Ambisonics (HOA), a sound field reproduction technology, is notable for defining a scalable encoding format that characterizes the sound field in a system-independent way. Sound fields sampled with a particular microphone array and encoded into the HOA format can be reproduced using any sound presentation device, typically a loudspeaker array, by using a HOA decoder. The HOA encoding format is based on the spherical harmonic decomposition; this makes it easier to design a decoder for large arrays of loudspeakers uniformly distributed over all directions. In practice, it is seldom possible to cover all directions with loudspeakers placed at regular angular intervals. An irregular array, one where the angular separation between adjacent loudspeakers is not constant, does not perform as well as a regular one when reproducing HOA due to the uneven sampling of the spherical harmonics. This paper briefly introduces the techniques used in HOA and advances a new approach to design HOA decoders for irregular loudspeaker arrays. The main difference between conventional methods and our proposal is the use of a new error metric: the radial derivative of the reconstruction error. Minimizing this metric leads to a smooth reproduction, accurate over a larger region than that achieved by conventional HOA decoders. We evaluate our proposal using the computer simulation of two 115-channel loudspeaker arrays: a regular and an irregular one. We find that our proposal results in a larger listening region when used to decode HOA for reproduction using the irregular array. On the other hand, applying our method matches the high-quality reproduction that can be attained with the regular array and conventional HOA decoders.

This paper proposes a sound source orientation estimation method that is suitable for a distributed microphone arrangement. The proposed method is based on orientation-extended beamforming (OEBF), which has four features: (a) robustness against reverberations, (b) robustness against noises, (c) free arrangements of microphones and (d) feasibility for real-time processing. In terms of (a) and (c), since OEBF is based on a general propagation model using transfer functions (TFs) that include all propagation phenomena such as reflections and diffractions, OEBF causes no model errors for the propagation phenomena, and is applicable to arbitrary microphone arrangements. Regarding (b), OEBF overcomes noise effects by incorporating three additional processes (Amplitude extraction, time-frequency mask and histogram integration) that are also proposed in this paper. As for (d), OEBF is executable in real-time basis as the execution process is the same as usual beamforming processes. A numerical experiment was performed to confirm the theoretical validity of OEBF. The results showed that OEBF was able to estimate sound source positions and orientations very precisely. Practical experiments were carried out using a 96-channel microphone array in real environments. The results indicated that OEBF worked properly even under reverberant and noisy environments and the averaged estimation error was given only 4°.