Orthogonal frequency division multiplexing with index modulation (OFDM-IM) is a novel scheme where the information bits are conveyed through the subcarrier activation pattern (SAP) and the symbols on the active subcarriers. Specifically, the subcarriers are partitioned into many subblocks and the subcarriers in each subblock can have two states, active or idle. Unfortunately, OFDM-IM inherits the high peak-to-average power ratio (PAPR) problem from the classical OFDM. The OFDM-IM signal with high PAPR induces in-band distortion and out-of-band radiation when it passes through high power amplifier (HPA). Recently, there are attempts to reduce PAPR by exploiting the unique structure of OFDM-IM, which is adding dither signals in the idle subcarriers. The most recent work dealing with the dither signals is using dithers signals with various amplitude constraints according to the characteristic of the corresponding OFDM-IM subblock. This is reasonable because OFDM subblocks have distinct levels of robustness against noise. However, the amplitude constraint in the recent work is efficient for only additive white Gaussian noise (AWGN) channels and cannot be used for maximum likelihood (ML) detection. Therefore, in this paper, based on pairwise error probability (PEP) analysis, a specific constraint for the dither signals is derived over a Rayleigh fading channel.

This letter deals with joint carrier frequency offset (CFO) and direction of arrival (DOA) estimation based on the minimum variance distortionless response (MVDR) criterion for interleaved orthogonal frequency division multiple access (OFDMA)/space division multiple access (SDMA) uplink systems. In order to reduce the computational load of two-dimensional searching based methods, the proposed method includes only once polynomial CFO rooting and does not require DOA paring, hence it raises the searching efficiency. Several simulation results are provided to illustrate the effectiveness of the proposed method.

Space is becoming increasingly congested and contested, which calls for effective means to conduct effective monitoring of high-value space assets, especially in Space Situational Awareness (SSA) missions, while there are imperfections in existing methods and corresponding algorithms. To overcome such a problem, this letter proposes an algorithm for accurate Connected Element Interferometry (CEI) in SSA based on more interpolation information and iterations. Simulation results show that: (i) after iterations, the estimated asymptotic variance of the proposed method can basically achieve uniform convergence, and the ratio of it to ACRB is 1.00235 in δ0 ∈ [-0.5, 0.5], which is closer to 1 than the current best AM algorithms; (ii) In the interval of SNR ∈ [-14dB, 0dB], the estimation error of the proposed algorithm decreases significantly, which is basically comparable to CRLB (maintains at 1.236 times). The research of this letter could play a significant role in effective monitoring and high-precision tracking and measurement with significant space targets during futuristic SSA missions.

Direct-current biased optical orthogonal frequency division multiplexing (DCO-OFDM) converts bipolar OFDM signals into unipolar non-negative signals by introducing a high DC bias, which satisfies the requirement that the signal transmitted by intensity modulated/direct detection (IM/DD) must be positive. However, the high DC bias results in low power efficiency of DCO-OFDM. An adaptively biased optical OFDM was proposed, which could be designed with different biases according to the signal amplitude to improve power efficiency in this letter. The adaptive bias does not need to be taken off deliberately at the receiver, and the interference caused by the adaptive bias will only be placed on the reserved subcarriers, which will not affect the effective information. Moreover, the proposed OFDM uses Hartley transform instead of Fourier transform used in conventional optical OFDM, which makes this OFDM have low computational complexity and high spectral efficiency. The simulation results show that the normalized optical bit energy to noise power ratio (Eb(opt)/N0) required by the proposed OFDM at the bit error rate (BER) of 10-3 is, on average, 7.5 dB and 3.4 dB lower than that of DCO-OFDM and superimposed asymmetrically clipped optical OFDM (ACO-OFDM), respectively.

Previously a method was reported to determine the mathematical representation of the microwave oscillator admittance by using numerical calculation. When analyzing the load characteristics and synchronization phenomena by using this formula, the analysis results meet with the experimental results. This paper describes a method to determine the mathematical representation manually.

A circular string formed by connecting the first and the last symbols of a string is one of the simplest sequence forms, and it has been used for many applications such as data compression and fragment assembly problem. A sufficient condition on the lengths of substrings with frequencies for reconstruction of an input circular binary string is shown. However, there are no detailed descriptions on the proof of the sufficient condition and reconstruction algorithm. In this paper, we prove a necessary and sufficient condition on the lengths of substrings with frequencies for reconstruction of the circular string. We show the length is shorter than that of previous study for some circular strings. For improving the length, we use minimal absent words (MAWs) for given substrings of length k, and we propose a new construction algorithm of MAWs of length h(>k) while a conventional construction algorithm of MAWs can construct MAWs of length l(≤k). Moreover, we propose reconstruction algorithm of an input circular string for given substrings satisfying the new condition.

In a field of biomedical engineering, not only low-pass filters for high frequency elimination but also notch filters for suppressing powerline interference are necessary to process low-frequency biosignals. For integration of low-frequency filters, chip implementation of large capacitances is major difficulty. As methods to enhance capacitances with small chip area, use of capacitance multipliers is effective. This letter describes design consideration of integrated low-frequency low-pass notch filter employing capacitance multipliers. Two main points are presented. Firstly, a new floating capacitance multiplier is proposed. Secondly, a technique to reduce the number of capacitance multipliers is proposed. By this technique, power consumption is reduced. The proposed techniques are applied a 3rd order low-pass notch filter. Simulation results show the effectiveness of the proposed techniques.

This letter introduces a prime-factor Galois field Fourier transform (PF-GFFT) architecture to frequency domain decoding (FDD) of cyclic codes. Firstly, a fast FDD scheme is designed which converts the original single longer Fourier transform to a multi-dimensional smaller transform. Furthermore, a ladder-shift architecture for PF-GFFT is explored to solve the rearrangement problem of input and output data. In this regard, PF-GFFT is considered as a lower order spectral calculation scheme, which has sufficient preponderance in reducing the computational complexity. Simulation results show that PF-GFFT compares favorably with the current general GFFT, simplified-GFFT (S-GFFT), and circular shifts-GFFT (CS-GFFT) algorithms in time-consuming cost, and is nearly an order of magnitude or smaller than them. The superiority is a benefit to improving the decoding speed and has potential application value in decoding cyclic codes with longer code lengths.

The frequency hopping sequence plays a crucial role in determining the system's anti-jamming performance, in frequency hopping communication systems. If the adjacent frequency points of FHS can ensure wide-gap, it will better improve the anti-interference capability of the FH communication system. Moreover, if the period of the sequence is expanded, and each frequency point does not repeat in the same sequence, the system's ability to resist electromagnetic interference will be enhanced. And a one-coincidence frequency-hopping sequence set consists of FHSs with maximum Hamming autocorrelation 0 and cross-correlation 1. In this paper, we present two constructions of wide-gap frequency-hopping sequence sets. One construction is a new class of wide-gap one-coincidence FHS set, and the other is a WGFHS set with long period. These two WGFHS sets are optimal with respect to WG-Peng-Fan bound. And each sequence of these WGFHS sets is optimal with respect to WG-Lempel-Greenberger bound.

This paper presents an analysis-based design method for designing the class-Φ22 wireless power transfer (WPT) system, taking its subsystems as a whole into account. By using the proposed design method, it is possible to derive accurate design values which can make sure the class-E Zero-Voltage-Switching/Zero-Derivative-Switching (ZVS/ZDS) to obtain without applying any tuning processes. Additionally, it is possible to take the effects of the switch on resistance, diode forward voltage drop, and equivalent series resistances (ESRs) of all passive elements on the system operations into account. Furthermore, design curves for a wide range of parameters are developed and organized as basic data for various applications. The validities of the proposed design procedure and derived design curves are confirmed by LTspice simulation and circuit experiment. In the experimental measurements, the class-Φ22 WPT system achieves 78.8% power-transmission efficiency at 6.78MHz operating frequency and 7.96W output power. Additionally, the results obtained from the LTspice simulation and laboratory experiment show quantitative agreements with the analytical predictions, which indicates the accuracy and validity of the proposed analytical method and design curves given in this paper.

Frame synchronization detection before data transmission is an important module which directly affects the lifetime and coexistence of underwater acoustic communication (UAC) networks, where linear frequency modulation (LFM) is a frame preamble signal commonly used for synchronization. Unlike terrestrial wireless communications, strong bursty noise frequently appears in UAC. Due to the long transmission distance and the low signal-to-noise ratio, strong short-distance bursty noise will greatly reduce the accuracy of conventional fractional fourier transform (FrFT) detection. We propose a multi-segment verification fractional fourier transform (MFrFT) preamble detection algorithm to address this challenge. In the proposed algorithm, 4 times of adjacent FrFT operations are carried out. And the LFM signal identifies by observing the linear correlation between two lines connected in pair among three adjacent peak points, called ‘dual-line-correlation mechanism’. The accurate starting time of the LFM signal can be found according to the peak frequency of the adjacent FrFT. More importantly, MFrFT do not result in an increase in computational complexity. Compared with the conventional FrFT detection method, experimental results show that the proposed algorithm can effectively distinguish between signal starting points and bursty noise with much lower error detection rate, which in turn minimizes the cost of retransmission.

In this study, we propose a method for localizing an unknown moving emitter by measuring a sequence of the frequency-of-arrival using a single moving observation platform. Furthermore, we introduce the position and velocity errors of the moving observation platform into the theoretical localization error equation to analyze the effect of these errors on the localization accuracy without Monte-Carlo simulations. The proposed theoretical error equation can propagate toward the time direction; therefore, the theoretical localization error can be evaluated at an arbitral time. We demonstrate that the localization error value obtained by the proposed equation and the RMSE evaluated by the Monte-Carlo simulation sufficiently coincide with one another.

We propose a novel silicon diplexer integrated with filters for frequency-division multiplexing in the 300-GHz band. The diplexer consists of a directional coupler formed of unclad silicon wires, a photonic bandgap-based low-pass filter, and a high-pass filter based on frequency-dependent bending loss. These integrated filters are capable of suppressing crosstalk and providing >15dB isolation over 40GHz, which is highly beneficial for terahertz-range wireless communications applications. We have used this diplexer in a simultaneous error-free wireless transmission of 300-GHz and 335-GHz channels at the aggregate data rate of 36Gbit/s.

Orthogonal frequency division multiplexing (OFDM) is very sensitive to the carrier frequency offset (CFO). The CFO estimation precision heavily makes impacts on the OFDM performance. In this paper, a new Bayesian learning-assisted joint CFO tracking and channel impulse response estimation is proposed. The proposed algorithm is modified from a Bayesian learning-assisted estimation (BLAE) algorithm in the literature. The BLAE is expectation-maximization (EM)-based and displays the estimator mean square error (MSE) lower than the Cramer-Rao bound (CRB) when the CFO value is near zero. However, its MSE value may increase quickly as the CFO value goes away from zero. Hence, the CFO estimator of the BLAE is replaced to solve the problem. Originally, the design criterion of the single-time-sample (STS) CFO estimator in the literature is maximum likelihood (ML)-based. Its MSE performance can reach the CRB. Also, its CFO estimation range can reach the widest range required for a CFO tracking estimator. For a CFO normalized by the sub-carrier spacing, the widest tracking range required is from -0.5 to +0.5. Here, we apply the STS CFO estimator design method to the EM-based Bayesian learning framework. The resultant Bayesian learning-assisted STS algorithm displays the MSE performance lower than the CRB, and its CFO estimation range is between ±0.5. With such a Bayesian learning design criterion, the additional channel noise power and power delay profile must be estimated, as compared with the ML-based design criterion. With the additional channel statistical information, the derived algorithm presents the MSE performance better than the CRB. Two frequency-selective channels are adopted for computer simulations. One has fixed tap weights, and the other is Rayleigh fading. Comparisons with the most related algorithms are also been provided.

The ionospheric clutter in High Frequency Surface Wave Radar (HFSWR) is the reflection of electromagnetic waves from the ionosphere back to the receiver, which should be suppressed as much as possible for the primary purpose of target detection in HFSWR. However, ionospheric clutter contains vast quantities of ionospheric state information. By studying ionospheric clutter, some of the relevant ionospheric parameters can be inferred, especially during the period of typhoons, when the ionospheric state changes drastically affected by typhoon-excited gravity waves, and utilizing the time-frequency characteristics of ionospheric clutter at typhoon time, information such as the trend of electron concentration changes in the ionosphere and the direction of the typhoon can be obtained. The results of the processing of the radar data showed the effectiveness of this method.

The low-hit-zone (LHZ) frequency hopping sequence (FHS) sets are widely applicable in quasi-synchronous frequency hopping multiple-access (QS-FHMA) systems. In order to reduce mutual interference (MI) in the zone around the signal origin between different users, we recommend the LHZ FHS set instead of the conventional FHS set. In this letter, we propose a design of LHZ FHS sets via interleaving techniques. The obtained sequences can be confirmed that they are near-optimal in relation to the Peng-Fan-Lee bound.

To cope with ever growing mobile data traffic, we recently proposed a concept of cellular ultra-dense radio access network (RAN). In the cellular ultra-dense RAN, a number of distributed antennas are deployed in the base station (BS) coverage area (cell) and user-clusters are formed to perform small-scale distributed multiuser multi-input multi-output (MU-MIMO) transmission and reception in each user-cluster in parallel using the same frequency resource. We also proposed a decentralized interference coordination (IC) framework to effectively mitigate both intra-cell and inter-cell interferences caused in the cellular ultra-dense RAN. The inter-cell IC adopted in this framework is the fractional frequency reuse (FFR), realized by applying the channel segregation (CS) algorithm, and is called CS-FFR in this paper. CS-FFR divides the available bandwidth into several sub-bands and allocates multiple sub-bands to different cells. In this paper, focusing on the optimization of the CS-FFR, we find by computer simulation the optimum bandwidth division number and the sub-band allocation ratio to maximize the link capacity. We also discuss the convergence speed of CS-FFR in a cellular ultra-dense RAN.

This paper proposes low complexity resource allocation in frequency domain non-orthogonal multiple access where many devices access with a base station. The number of the devices is assumed to be more than that of the resource for network capacity enhancement, which is demanded in massive machine type communications (mMTC). This paper proposes two types of resource allocation techniques, all of which are based on the MIN-MAX approach. One of them seeks for nicer resource allocation with only channel gains. The other technique applies the message passing algorithm (MPA) for better resource allocation. The proposed resource allocation techniques are evaluated by computer simulation in frequency domain non-orthogonal multiple access. The proposed technique with the MPA achieves the best bit error rate (BER) performance in the proposed techniques. However, the computational complexity of the proposed techniques with channel gains is much smaller than that of the proposed technique with the MPA, whereas the BER performance of the proposed techniques with channel gains is only about 0.1dB inferior to that with the MPA in the multiple access with the overloading ratio of 1.5 at the BER of 10-4. They attain the gain of about 10dB at the BER of 10-4 in the multiple access with the overloading ration of 2.0. Their complexity is 10-16 as small as the conventional technique.

This paper presents a divide-by-9 injection-locked frequency divider (ILFD). It can lock onto about 6-GHz input with a locking range of 3.23GHz (58%). The basic concept of the ILFD is based on employing self-gated multiple inputs into the multiple-stage ring oscillator. A wide lock range is also realized by adapting harmonic-control circuits, which can boost specific harmonics generated by mixing. The ILFD was fabricated using a 55-nm deeply depleted channel (DDC) CMOS process. It occupies an area of 0.0210mm2, and consumes a power of 14.4mW.

A novel displacement sensor was proposed based on a frequency delta-sigma modulator (FDSM) employing a microwave oscillator. To demonstrate basic operation, we fabricated a stylus surface profiler using a cylindrical cavity resonator, where one end of the cavity is replaced by a thin metal diaphragm with a stylus probe tip. Good surface profile was successfully obtained with this device. A 10 nm depth trench was clearly observed together with a 10 µm trench in a single scan without gain control. This result clearly demonstrates an extremely wide dynamic range of the FDSM displacement sensors.