High-performance computing (HPC) has penetrated into various research fields, yet the increase in computing power is limited by conventional electrical interconnections. The proposed architecture, NEST, exploits wavelength routing in arrayed waveguide grating routers (AWGRs) to achieve a scalable, low-latency, and high-throughput network. For the intra pod and inter pod communication, the symmetrical topology of NEST reduces the network diameter, which leads to an increase in latency performance. Moreover, the proposed architecture enables exponential growth of network size. Simulation results demonstrate that NEST shows 36% latency improvement and 30% throughput improvement over the dragonfly on an average.

To achieve high end-to-end availability in nationwide optical transport network across thousands of office buildings, it is important to properly make each function redundant, and execute protection switching, repair failed functions and recover redundancy to prevent multiple simultaneous failures. High redundancy leads to high system cost and high power consumption, and tight conditions for recovery leads to high maintenance cost. Therefore it is important to optimize the balance between redundancy and maintenance condition based on appropriate availability indicators. We previously proposed a resource-pool control mechanism for a nationwide optical transport network that can optimize the balance. This paper proposes an end-to-end availability evaluation scheme for a nationwide optical transport network with our mechanism, by which network operators can design the pool-resource amount of each function and the maintenance conditions for each network area properly to satisfy the end-to-end availability requirement. Although the maintenance conditions are usually discussed based on failure-recovery times, they should be discussed based on cost- or load-based volumes for this design. This paper proposes a maintenance-operation-load evaluation scheme, which derives the required number of maintenance staff members from failure-recovery times. We also discuss the design of the pool-resource amount and maintenance conditions for each network area of a nationwide network based on the proposed evaluation schemes.

Computer-generated hologram based on ray-sampling plane method was newly applied to the projection-type holographic display that consists of the holographic projection and the holographic optical element screen. In the proposed method, geometric deformation characteristic of the holographic image via the display system was mathematically derived and canceled out by the coordinate transformation of ray-sampling condition to avoid the image distortion. In the experiment, holographic image reconstruction with the arbitral depth expression without image distortion could be optically demonstrated.

Optical interconnect is a promising candidate for network on chip. As the key element in the network on chip, the routers greatly affect the performance of the whole system. In this letter, we proposed a new router architecture, Waffle, based on compact 2×2 hybrid photonic-plasmonic switching elements. Also, an optimized architecture, Waffle-XY, was designed for the network employed XY routing algorithm. Both Waffle and Waffle-XY are strictly non-blocking architectures and can be employed in the popular mesh-like networks. Theoretical analysis illustrated that Waffle and Waffle-XY possessed a better performance compared with several representative routers.

This paper investigates approaches that can cancel nonlinear phase noise effectively for the phase-conjugate pair diversity transmission of 16-QAM WDM signals through multi-core fiber. The geometric mean is introduced for the combination of the phase-conjugate pair. A numerical simulation suggests that span-by-span chromatic dispersion compensation is more effective at cancelling phase noise in long distance transmission than lumped compensation at the receiver. Simulations suggest the span-wise compensation described herein yields Q-value enhancement of 7.8 and 6.8dB for CD values of 10 and 20.6ps/nm/km, respectively, whereas the lumped compensation equivalent attains only 3.5dB. A 1050km recirculating loop experiment confirmed a Q-value enhancement of 4.1dB for 20.6ps/nm/km, span-wise compensation transmission.

This paper introduces a formation method for 3-dimensional 6 ch.×6 ch. shuffling structures with graded-index (GI) circular core in a multimode polymer optical waveguide for optical printed circuit boards (OPCBs) using a unique photomask-free fabrication technique named the Mosquito method. The interchannel pitch of the fabricated waveguides is 250µm, where all the channels consist of both horizontal and vertical bending structures and the last 6 channels in parallel cross over the first 6 channels. We also report 3-dimensional S-shaped polymer waveguides. In the S-shaped waveguides, the first and last 6 channels with both horizontal and vertical core bending composing the above 3-dimensional shuffling waveguide are separated, in order to evaluate the effect of over-crossing on the loss. It is experimentally confirmed that there is no excess insertion loss due to the shuffling structure in the 3-D shuffling waveguide. The evaluated crosstalk of the 3-D shuffling waveguide is lower than -30dB. The 3-D shuffling waveguide proposed in this paper will be a promising component to achieve high bandwidth density wiring for on-board optical interconnects.

Recent advances in phase-sensitive amplifiers (PSAs) using periodically poled LiNbO3 are reviewed. Their principles of operation and distinct features are described. Applications in optical communication are studied in terms of the inline operation and amplification of a sophisticated modulation format. Challenges for the future are also discussed.

We review the recent advances on strain and temperature sensing techniques based on multimodal interference in perfluorinated (PF) graded-index (GI) polymer optical fibers (POFs). First, we investigate their fundamental characteristics at 1300nm. When the core diameter is 62.5µm, we obtain strain and temperature sensitivities of -112pm/µε and +49.8nm/°C, the absolute values of which are, by simple calculation, approximately 13 and over 1800 times as large as those in silica GI multimode fibers, respectively. These ultra-high strain and temperature sensitivities probably originate from the unique PF polymer used as core material. Subsequently, we show that the temperature sensitivity (absolute value) is significantly enhanced with increasing temperature toward ∼70°C, which is close to the glass-transition temperature of the core polymer. When the core diameter is 62.5µm, the sensitivity at 72°C at 1300nm is 202nm/°C, which is approximately 26 times the value obtained at room temperature and >7000 times the highest value previously reported using a silica multimode fiber. Then, we develop a single-end-access configuration of this strain and temperature sensing system, which enhances the degree of freedom in embedding the sensors into structures. The light Fresnel-reflected at the distal open end of the POF is exploited. The obtained strain and temperature sensitivities are shown to be comparable to those in two-end-access configurations. Finally, we discuss the future prospects and give concluding remarks.

Ring-based topology is popular for optical network-on-chip. However, the network congestion is serious for ring topology, especially when optical circuit-switching is employed. In this paper, we proposed an algorithm to build a low congestion multi-ring architecture for optical network-on-chip without additional wavelength or scheduling overhead. A network congestion model is established with new network congestion factor defined. An algorithm is developed to optimize the low congestion multi-ring topology. Finally, a case study is shown and the simulation results by OPNET verify the superiority over the traditional ONoC architecture.

By focusing on the recent swing to the centralized approach by the software defined network (SDN), this paper presents a novel network architecture for refactoring the current distributed Internet protocol (IP) by not only utilizing the SDN itself but also implementing its cooperation with the optical transport layer. The first IP refactoring is for flexible network topology reconfiguration: the global routing and explicit routing functions are transferred from the distributed routers to the centralized SDN. The second IP refactoring is for cost-efficient maintenance migration: we introduce a resource portable IP router that can behave as a shared backup router by cooperating with the optical transport path switching. Extensive evaluations show that our architecture makes the current IP network easier to configure and more scalable. We also validate the feasibility of our proposal.

To realize three-dimensional (3D) optical interconnection on large-scale integration (LSI) circuits, layer-to-layer couplers based on Si-photonics platform were reviewed. In terms of optical cross talk, more than 1 µm layer distance is required for 3D interconnection. To meet this requirement for the layer-to-layer optical coupler, we proposed two types of couplers: a pair of grating couplers with metal mirrors for multi-layer distance coupling and taper-type directional couplers for neighboring layer distance coupling. Both structures produced a high coupling efficiency with relatively compact (∼100 µm) device sizes with a complementary metal oxide semiconductor (CMOS) compatible fabrication process.

To meet the demand for continuous increase in data traffic, full usage of polarization freedom of light is becoming inevitable in the next-generation optical communication and datacenter networks. In particular, Stokes-vector modulation direct-detection (SVM-DD) formats are expected as potentially cost-effective method to transmit multi-level signals without using costly coherent transceivers in the short-reach links. For the SVM-DD formats to be practical, both the transmitter and receiver need to be substantially simpler, smaller, and lower-cost as compared to coherent counterparts. To this end, we have recently proposed and demonstrated novel SV modulator and receiver circuits realized on monolithic InP platforms. With compact non-interferometric configurations, relatively simple fabrication procedures, and compatibility with other active photonic components, the proposed devices should be attractive candidate in realizing low-cost monolithic transceivers for SVM formats. In this paper, we review our approaches as well as recent progresses and provide future prospects.

We have proposed and developed new electro-optic modulators for the pre-equalization of signal distortion caused by the optical fiber chromatic dispersion effect. We found that the synthesis of an almost arbitrary impulse response function is obtainable by utilizing an electro-optic modulator composed of a Mach-Zehnder waveguide and travelling-wave electrodes on a ferro-electric material substrate with polarization-reversed structures. In this paper, the operational principle, design and simulation results of the pre-equalization modulator are presented. Some preliminary experimental results are also shown with future prospects.

A novel adaptive code division multiplexing system with hybrid electrical and optical codes is proposed for flexible and dynamic resource allocation in next generation asynchronous optical access networks. We analyze the performance of a 10Gbps × 12 optical node unit, using hierarchical 8-level optical and 4-level electrical phase shift keying codes.

Orthogonal frequency division multiplexing (OFDM) promises to provide the necessary boost in the core networks' capacity along with the required flexibility in order to cope with the Internet's growing heterogeneous traffic. At the same time, wavelength division multiplexing (WDM) technology remains a cost-effective and reliable solution especially for long-haul transmission. Due to the higher implementation cost of optical OFDM transmission technology, it is expected that OFDM-based bandwidth variable transponders (BVT) will co-exist with conventional WDM ones. In this paper, we provide an integer linear programming (ILP) formulation that minimizes the cost and power consumption of such hybrid architecture and then a comparison is made with a pure OFDM-based elastic optical network (EON) and a mixed line rate (MLR) WDM optical network in order to evaluate their cost and energy efficiency.

We describe the design and simulation of a suitable branching ratio for an optical coupler for a cable re-routing operation support system with no service interruption, and report our experimental results. We also show the risk analysis, and report that the branching ratio was 0.47 where the probability was 99.7% that the maximum acceptable cable loss of a detour line was more than that of the current line.

We present an 82.5GS/s over-sampling based burst-mode clock and data recovery (BM-CDR) IC chip-set comprising an 82.5GS/s over-sampling IC using 8×10.3GHz multi-phase clocks and a dual-rate data selector logic IC to realize the 10.3Gb/s and 1.25Gb/s dual-rate burst-mode fast-lock operation required for 10-Gigabit based fiber-to-the-x (FTTx) services supported by 10-Gigabit Ethernet passive optical network (10G-EPON) systems. As the key issue for designing the proposed 82.5GS/s BM-CDR, a fresh study of the optimum number of multi-phase clocks, which is equivalent to the sampling resolution, is undertaken, and details of the 10.3Gb/s cum 1.25/Gb/s dual-rate optimum phase data selection logic based on a blind phase decision algorithm, which can realize a full single-platform dual-rate BM-CDR, ate also presented. By using the power of the proposed 82.5GS/s over-sampling BM-CDR in cooperation with our dual-rate burst-mode optical receiver, we further demonstrated that a short dual-rate and burst-mode preamble of 256ns supporting receiver settling and CDR recovery times was successfully achieved, while obtaining high receiver sensitivities of -31.6dBm at 10.3Gb/s and -34.6dBm at 1.25Gb/s and a high pulse-width distortion tolerance of +/-0.53UI, which are superior to the 10G-EPON standard.

The spread of optical access broadband networks using Fiber to the Home (FTTH) has not reached the rural areas of developing countries. The current state of global deployment of ICT indicates that it is difficult to sell network systems as stand-alone products due to prohibitive costs, and the demand is for total services that include construction, maintenance, and operation. Moreover, there is a need to offer proposals that include various solutions utilizing broadband networks, as well as for a business model that takes the sustainability of those solutions into consideration. In this paper, we discuss the issues in constructing broadband networks, introduce case studies of solutions using broadband networks for solving social issues in rural areas of developing countries, and discuss the challenges in the deployment of the solutions.

This paper proposes a transmission control protocol (TCP) for long distance high-speed wireless communications, including free-space optical communications (FSOC). Extreme high frequency of wireless communications enables high-speed bit rate, but frequent signal error, including burst error, can be a quite severe problem for ordinary high-speed TCPs. To achieve 10Gbps or higher data transfer throughput on FSOC, the proposed TCP (designated “TCP-FSO”) has improved and new features including multi-layer congestion control, retransmission control with packet loss point estimation, delay-based ACK congestion control, and ACK retransmission control. We evaluated data transfer throughput of TCP-FSO and the other TCPs, by throughput model analysis and experiment on real implementation. Obtained results show that TCP-FSO achieves far higher data transfer throughput than other high-speed TCPs. For example, it achieved a thousand times higher throughput than the other high-speed TCPs in a real FSOC environment.

This paper demonstrates the suppressing power of 10 Gbps On Off keyed signal using biased half-wave rectification. Authors have previously reported that radio frequency (RF) and optical on-off keying (OOK) signal can be simultaneously transmitted over the radio over fiber (RoF) link [1]. Since the optical OOK signal has much broader bandwidth compared to RF signal, it interferes with RF signal. Reference [1] experimentally shows that the optical OOK signal degrades the RF signal in terms of signal-to-noise power ratio (SNR) when 10 Gbps OOK and 1.9 GHz microwave are employed as baseband and RF, respectively. This paper proposes an interference suppression, and the proposal is subsequently used for detecting the RF signal. Experiments are conducted for the purpose of the proof-of-concept of the proposal. Finally numerical simulations are employed to show the performance enhancement in terms of error vector magnitude (EVM).