We developed piezoresistors with an intrinsic compensation of the offset temperature characteristics. High energy ion implantation was applied to fabricate this type of piezoresistor. The dopant profile of the buried piezoresistor resembles to that of the junction gate field effect transistor (JFET). The buried layer corresponds to a channel of JFET, and the substrate bias corresponds to the gate voltage. Owing to the independent temperature varying parameters, i.e., width of the depletion layer and carrier mobility in the channel, the drain current of the JFET has a temperature independent point at an appropriate gate source voltage. The effect was used in the new type of buried piezoresistor which has a driving point of zero temperature coefficient of resistance at an appropriate gate source voltage.

The potential attenuation process of charged human body (HB) is analyzed. A two-dimensional circuit model is presented for predicting the potential attenuation characteristics of the HB charged on the floor. The theoretical equation for the HB potential is derived in the closed form in the Laplacian transformation domain, and the numerical inverse Laplace transform is used to compute it. The half-life or relaxation time of the HB potential for decay is numerically examined with respect to the electrical parameters of shoes. The experiment is also conducted for verifying the validity of the computed result.

The wave forms of electric and magnetic fields radiated by short gap discharges are measured to analyze electrostatic discharge (ESD) events in the near-field zone with the monopole antennas, the loop antenna and the 5.5GHz bandwidth waveform digitizer. The antenna outputs are corrected by the measured characteristics of the antennas. The relations between the measured electric field and the discharge currents are discussed.

The effects of Gaussian electromagnetic noise and non-Gaussian one on TV picture degradation are studied by using a composite noise generator which can control noise parameters. Three kinds of still pictures and four kinds of motion pictures are tested, and the picture degradation is subjectively evaluated with five-grade impairment scale. The tendency of the picture degradation against the every picture is almost the same. But MOS (Mean Opinion Score) between still picture and motion picture degradation is different in some measure when the power of burst noise is small.

On mutually coupling lines, the transmission signal is dispersively propagated by crosstalk coupling between lines and shows complex propagation characteristics caused by reciprocal reflections. Usually, the differential equation and the integral equation have been applied to analyze the solutions of transmission lines. In this paper, we propose a different analytical method of the propagation characteristics of signal and crosstalk noise. By setting up crosstalk coupling line as a sectionally divided digital transmission network and by using the signal flow graph and the difference equation, the propagation characteristics in the frequency domain, the space domain and the time domain on mutually coupling lines can be obtained. To verify the validity of this method and analyze the complex propagation problems, we first study the crosstalk characteristics of a twisted pair cable via the third circuit by unidirectional coupling. Subsequently we will analyze the coupling theory of bidirectional coupling lines.

The efficiency of a guided-probe fault location process is affected by the number of the probed lines. This number depends on the size of the target area and the method by which a line is selected for probing. This paper presents a method for reducing the size of the target area in a sequential circuit by introducing the concepts of Type- and Type- faults. This paper also presents a method of selecting lines for probing in a more efficient way. The efficiency of the proposed methods is demonstrated by experimental results.

This paper proposes a large capacity high-speed file memory system implemented with wafer scale RAM which adopts a novel defect-tolerant technique. Based on set-associative mapping, the defective memory blocks on the wafer are repaired by switching with the spare memory blocks. In order to repair the clustered defective blocks, these are permuted logically with other blocks by adding some constant value to the input block addresses. The defective blocks remaining even after applying the above two methods are repaired by using error control codes which correct soft errors induced by alpha particles in an on-line operation as well as hard errors induced by the remaining defective blocks. By using the proposed technique, this paper demonstrates a large capacity high-speed WSI file memory system implemented with high fabrication yield and low redundancy rate.

In the present paper, we attempt to show that the information about input patterns must be as small as possible for improving the generalization performance under the condition that the network can produce targets with appropriate accuracy. The information is defined with respect to the hidden unit activity and we suppose that the hidden unit has a crucial role to store the information content about input patterns. The information is defined by the difference between uncertainty of the hidden unit at the initial stage of the learning and the uncertainty of the hidden unit at the final stage of the learning. After having formulated an update rule for the information minimization, we applied the method to a problem of language acquisition: the inference of the past tense forms of regular and irregular verbs. Experimental results confirmed that by our method, the information was significantly decreased and the generalization performance was greatly improved.

GaAs-based micromachining is a very attractive technique for integrating mechanical structures and active optical devices, such as laser diodes and photodiodes. For monolithically integrating mechanical parts onto laser diode wafers, the micromachining technique must be compatible with the laser diode fabrication process. Our micromachining technique features three major processes: epitaxitial growth (MOVPE) for both the structural and sacrificial layers, reactive dry-etching by chlorine for high-aspect, three-dimensional structures, and selective wet-etching by peroxide/ammonium hydroxide solution to release the moving parts. These processes are compatible with laser fabrication, so a cantilever beam structure can be fabricated at the same time as a laser diode structure. Furthermore, a single-crystal epitaxial layer has little residual stress, so precise microstructures can be obtained without significant deformation. We fabricated a microbeam resonator sensor composed of two laser diodes, a photodiode, and a micro-cantilever beam with an area of 400700 µm. The cantilever beam is 3 µm wide, 5 µm high, and either 110µm long for a 200-kHz resonant frequency or 50 µm long for a 1-MHz resonant frequency. The cantilever beam is excited by an intensity-modulated laser beam from an integrated excitation laser diode; the vibration signal is detected by a coupled cavity laser diode and a photodiode.

Dynamic Term Rewriting Calculus (DTRC) is a new computation model aiming at formal description and verification of algorithms treating Term Rewriting Systems (TRSs). In this paper, we show that we can use DTRC to mechanize explicit induction for proving an inductive theorem, that is, we can translate the statements of base and induction steps for proving by induction into a DTRC term. The translation reduces the proof of the statements into the evaluation of the corresponding DTRC term.

Finite element analysis is carried out to provide an engineering design approach of a newly proposed Triple-TEM cell (TTEM cell). Important characteristics such as characteristic impedance, TEM mode field distribution, as well as TE and TM modes cutoff frequencies can be analyzed by using the software developed in this paper. Design guidelines have been provided for the TTEM cell. Reasonable geometric structure of the cross-sectional area of the TTEM cell would thereupon be resolved. Numerical results of the local higher order modes along the length of the cell are presented in this paper.

A black membrane is a biological-membrane analogue, i.e. a phospholipid bilayer membrane, artificially formed on an orifice immersed in water. It is used to investigate the properties of the membrane itself and channels embedded therein. In this paper, microfabrication techniques are applied to fabricate the orifice, and a glass substrate is isotropically etched to define the orifice geometry. The periphery of the orifice was patterned with aminosilane to anchor the membrane. The remainder part was coated with fluorosilane to make the surface hydrophobic and to prevent adsorption of channel-forming molecules. We demonstrated experimentally that a stable and reproducible membrane is easily obtainable using the orifice.

This paper proposes a constructive linearization method for transistor circuits based on a polynomial representation of nonlinear transfer functions. The nonlinear transfer functions for various configurations have been shown in a polynomial form. Then the results have been applied to several bipolar transistor circuits to exemplify the proposed designing method.

The precise phase characteristics of the reflected and transmitted waves are obtained for electromagnetic scattering by inductive discontinuities of finite thickness located in rectangular waveguides. The incident wave is assumed to be the dominant mode, and the modified residue-calculus method is used for numerical analysis. The phase characteristics when the thickness and width of the iris are varied, and characteristics of the reflected and transmitted waves when resonance appears, are discussed. In addition, an X-band experiment is performed and the calculations for both the reflected and transmitted waves are shown to agree well with the experimental values.

The antenna factor measurement of the dipole antennas for electromagnetic interference (EMI) measurements is studied theoretically and experimentally. The 3-antenna method is applied to near-field. Near-field transmission characteristics between the transmitting and receiving dipole antennas is obtained by using the electromotive force (EMF) method, where sinusoidal current distributions are assumed. It is shown that the antenna factors can be measured from transmission values between two antennas and near-field correction factors at any height of each antenna.

It is shown by the derivation of solution methods for an elementary optimization problem that the stochastic relaxation in image analysis, the Potts neural networks for combinatorial optimization and interior point methods for nonlinear programming have common formulation of their dynamics. This unification of these algorithms leads us to possibility for real time solution of these problems with common analog electronic circuits.

A permutation cipher scheme using polynomials over a field is presented. A permutation as well as substitution plays a major role in almost all conventional cryptosystems. But the security of the permutation depends on how symbols are permuted. This paper proposes the use of polynomials for the permutation and show that the scheme satisfies the following security criteria. (1) There are enough encryption keys to defend exhaustive attacks. (2) The permutation moves almost all samples into places which are different from the original places. (3) Most samples are shifted differently by different permutations. The permutation cipher scheme could be regarded as a scheme based on Reed-Solomon codes. The information symbols of the codes compose a key of the permutation cipher scheme.

This paper reports on a new dynamic scanning force microscope (SFM), in which the piezoelectric microcantilever is utilized for the lever excitation and displacement sensing. Piezoelectric cantilevers can detect their deflection without external sensing elements and be vibrated with no oscillator outside. The cantilever integrated with the deflection detector and the oscillator changes the conventional construction of a dynamic SFM and expands its range of applicability. The microcantilever used consists of a ZnO layer sandwiched with Au electrodes deposited on a thin beam of thermally grown SiO2. The length, width and thickness of the lever are 125 µm, 50 µm and 3.5 µm, respectively. We have characterized this cantilever by measuring the charge spectrum and the frequency dependence of the admittance. From the charge spectrum the mechanical quality factor measured 300 in free vibration. Typical piezoelectric constant of the ZnO film was estimated approximately as 80% of single-crystal's value. The piezoelectric cantilever can be vibrated by applying the voltage with the frequency near the resonance to the piezoelectric layer. The excited amplitude per unit voltage at the resonance frequency was calculated as about 5 µm/V. The cantilever amplitude can be detected by measuring the current between electrodes, since the admittance depends on the quality factor. We have constructed a dynamic SFM without external oscillator and detector, and successfully obtained the surface images of a sol-gel derived PZT film in the cyclic contact operation mode. The longitudinal resolution of the SFM system was 0.3 nm at a 125 Hz bandwidth.

A method is described for approximately estimating the surface specific-absorption-rate (SAR) in an anatomically realistic model of the human head for microwave exposure using the external magnetic near-field. The finite-difference time-domain (FD-TD) technique is used to compute the electromagnetic fields in the head model for 750-MHz and 1.5-GHz far-field exposures with the 1991 ANSI specified safety level. The spatial pattern tracking between the one-gram averaged surface-SAR and external magnetic near-field is demonstrated on the horizontal cross sectional perimeter of the head model. The regression coefficients between them are also obtained on the fifty-five horizontal cross sectional perimeters, which could give an approximate value of the surface-SAR in an acutual head, if the external magnetic near-field would be measured. This is validated by the theoretical results in a semi-infinite homogeneous flat model for normal incidence microwave exposure.

The analysis of the shielding properties of a planar wire-mesh shield embedded in a general isotropic--chirality is included--or anisotropic stratified media is here presented. A suitable model of the grating has been introduced in order to consider the occuring phenomena, in fact through a spectral technique the electromagnetic problem is translated into the equivalent circuit network model that allows to express the time response of the shielded field for the NEMP incidence in a closed form.