This paper proposes a topology of high power, MHz-frequency, half-bridge resonant inverter ideal for low-loss Gallium Nitride high electron mobility transistor (GaN-HEMT). General GaN-HEMTs have drawback of low drain-source breakdown voltage. This property has prevented conventional high-frequency series resonant inverters from delivering high power to high resistance loads such as 50Ω, which is typically used in radio frequency (RF) systems. High resistance load causes hard-switching also and reduction of power efficiency. The proposed topology overcomes these difficulties by utilizing a proposed ‘L-S network’. This network is effective combination of a simple impedance converter and a series resonator. The proposed topology provides not only high power for high resistance load but also arbitrary design of output wattage depending on impedance conversion design. In addition, the current through the series resonator is low in the L-S network. Hence, this series resonator can be designed specifically for harmonic suppression with relatively high quality-factor and zero reactance. Low-distortion sinusoidal 3kW output is verified in the proposed inverter at 13.56MHz by computer simulations. Further, 99.4% high efficiency is achieved in the power circuit in 471W experimental prototype.

The performance of conventional direction of arrival (DOA) methods is susceptible to the uncertainty of acoustic velocity in the underwater environment. To solve this problem, an underwater DOA estimation method with L-shaped array for wide-band signals under unknown acoustic velocity is proposed in this paper. The proposed method refers to the idea of incoherent signal subspace method and Root-MUSIC to obtain two sets of average roots corresponding to the subarray of the L-shaped array. And the geometric relationship between two vertical linear arrays is employed to derive the expression of DOA estimation with respect to the two average roots. The acoustic velocity variable in the DOA estimation expression can be eliminated in the proposed method. The simulation results demonstrate that the proposed method is more accurate and robust than other methods in an unknown acoustic velocity environment.

A Mach-Zehnder optical modulator with the tunable multimode interference coupler was fabricated using Ti-diffused LiNbO3. The modulation extinction ratio could be voltage controlled to maximize up to 50 dB by tuning the coupler. Optical single-sideband modulation was also achieved with a sideband suppression ratio of more than 30 dB.

This paper describes a method to evaluate the modulated waveforms output by a high-speed external phase modulator over a wide wavelength range by using linear optical sampling (LOS) and a wavelength-swept light source. The phase-modulated waveform is sampled by LOS together with the reference signal before modulation, and the modulation waveform is observed by removing the phase noise of the light source extracted from the reference signal. In this process, the frequency offset caused by the optical-path length difference between the measurement and reference interferometers is removed by digital signal processing. A pseudo-random binary-sequence modulated signal is observed with a temporal resolution of 10ps. We obtained a dynamic range of ∼40dB for the measurement bandwidth of 10 nm. When the measurement bandwidth is expanded to entire C-Band (∼35nm), the dynamic ranges of 37∼46dB were observed, depending on the wavelengths. The measurement time was sub-seconds throughout the experiment.

This paper proposes a novel multi-layer substrate integrated waveguide (SIW) resonator loaded with asymmetric E-shaped slot-lines and shows a tri-band band-pass filter (BPF) using the proposed structure. In the previous literature, various SIW resonators have been proposed to simultaneously solve the problems of large area and high insertion loss. Although these SIWs have a lower insertion loss than planar-type resonators using a printed circuit board, the size of these structures tends to be larger. A multi-layer SIW resonator loaded with asymmetric E-shaped slot-lines can solve the above problems and realize a tri-band BPF without increasing the size to realize further miniaturization. The theoretical design method and the structural design are shown. Moreover, the configured structure is fabricated and measured for showing the validity of the design method in this paper.

As known to us all, L-shaped co-prime array (LCA) is a recently introduced two-dimensional (2-D) sparse array structure, which is extended from linear co-prime array (CA). Such sparse array geometry can be used for 2-D parameters estimation with higher degrees-of-freedom (DOF). However, in the scenario where several narrowband transmissions spread over a wide spectrum, existing technique based on LCA with Nyquist sampling may encounter a bottleneck for both analog and digital processing. To alleviate the burden of high-rate Nyquist sampling, a method of joint wideband spectrum and direction-of-arrival (DOA) estimation with compressed sampling based on LCA, which is recognized as LCA-based modulated wideband converter (MWC), is presented in this work. First, the received signal along each antenna is mixed to basebands, low-pass filtered and down-sampled to get the compressed sampling data. Then by constructing the virtual received data of 2-D difference coarray, we estimate the wideband spectrum and DOA jointly using two recovery methods where the first is a joint ESPRIT method and the other is a joint CS method. Numerical simulations illustrate the validity of the proposed LCA based MWC system and show the superiority.

This paper presents improvement of port-to-port isolation characteristics of a linearly dual-polarized dual-band and wideband multi-ring microstrip antenna (MR-MSA) fed by two L-probes. The linearly dual-polarized dual-band and wideband MR-MSA consists of two circular ring patches and two L-probes arranged in a multi-layered dielectric substrate. By using a thick substrate for the L-probe and arranging two ring patches as radiation elements, the proposed antenna operates wideband and dual-band characteristics. Furthermore, by arranging two L-probes at the orthogonal positions, the proposed antenna can radiate dual linear polarizations. In this paper, for improving port-to-port isolation characteristics of the linearly dual-polarized dual-band and wideband MR-MSA fed by two L-probes, a via connected to the ground plane at the center of the radiation elements is arranged. The fractional bandwidths below -10dB reflection obtained by the simulation of the MR-MSA with the via were 17.0% and 14.4%. Furthermore, the simulated isolation characteristics were more than 21.0dB and 17.0dB in the two bands. Improvement of the isolation characteristics between two ports as well as the dual-band and wideband performance of the proposed MR-MSA with the via were confirmed by the simulation and the measurement.

A linear and broadband power amplifier (PA) for 5G phased-array is presented. The design improves the linearity by operating the transistors in deep class AB region. The design broadens the bandwidth by applying the inter-stage weakly-coupled transformer. The theory of transformers is illustrated by analyzing the odd- and even-mode model. Based on this, the odd-mode Q factor is used to evaluate the quality of impedance matching. Weakly- and strongly-coupled transformers are compared and analyzed in both the design process and applicable characteristics. Besides, a well-founded method to achieve the transformer-based balanced-unbalanced transformation is proposed. The fully integrated two-stage PA is designed and implemented in a 65-nm CMOS process with a 1-V power supply to provide a maximum small-signal gain of 19dB. The maximum output 1-dB compressed power (P1dB) of 17.4dBm and the saturated output power (PSAT) of 18dBm are measured at 28GHz. The power-added efficiency (PAE) of the P1dB is 26.5%. From 23 to 32GHz, the measured P1dB is above 16dBm, covering the potential 5G bands worldwide around 28GHz.

This paper proposes a methodology for designing broadband class B/J power amplifier based on a mirrored lowpass filter matching structure. According to this filter theory, the impedance of this design method is mainly related to the cutoff frequency. Series inductors and shunt capacitors filter out high frequencies. The change of input impedance with frequency is small in the passband. Which can suppress higher harmonics and expand bandwidth. In order to confirm the validity of the design method, a broadband high-efficiency power amplifier in the 1.3 - 3.9GHz band is designed and fabricated. Measurement results show that the output power is greater than 40.5dBm, drain efficiency is 61.2% - 70.8% and the gain is greater than 10dB.

The narrow bandwidth limitation of 300-3400Hz on the public switching telephone network results in speech quality deterioration. In this paper, we propose an artificial bandwidth extension approach that reconstructs the missing lower bandwidth of 50-300Hz using sinusoidal synthesis based on the first formant location. Sinusoidal synthesis generates sinusoidal waves with a harmonic structure. The proposed method detects the fundamental frequency using an autocorrelation method based on YIN algorithm, where a threshold processing avoids the false fundamental frequency detection on unvoiced sounds. The amplitude of the sinusoidal waves is calculated in the time domain from the weighted energy of 300-600Hz. In this case, since the first formant location corresponds to the first peak of the spectral envelope, we reconstruct the harmonic structure to avoid attenuating and overemphasizing by increasing the weight when the first formant location is lower, and vice versa. Consequently, the subjective and objective evaluations show that the proposed method reduces the speech quality difference between the original speech signal and the bandwidth extended speech signal.

In this paper, a linear array of 4 leaf-shaped bowtie slot antennas is proposed for use in quasi-millimeter wave band. The slot antennas array is designed to operate at 28GHz frequency band. The leaf-shaped bowtie slot antenna is a type of self-complementary antenna with low profile and low cost of fabrication. The proposed antenna structure offers improvement in radiation pattern, gain, and -10dB impedance bandwidth. Through out of this paper radiation pattern, actual gain, and -10dB impedance bandwidth are evaluated by Finite Different Time Domain (FDTD) simulation. Antenna characteristics are analyzed in the frequency range of 27GHz to 29GHz. To improve antenna characteristics such as actual gain and -10dB impedance bandwidth, a dielectric superstrate layer with relative permittivity of 10.2 is placed on top of ground plane of the slot antennas array. Three antenna structures are introduced and compared. With two layers of dielectric superstrate on top of the antennas ground plane, analysis results show that -10dB impedance bandwidth occupies the frequency range of 27.17GHz to 28.39GHz. Therefore, the operational impedance bandwidth is 1.22GHz. Maximum actual gain of the slot antennas array with two dielectric superstrate layers is 20.49dBi and -3dB gain bandwidth occupies the frequency range of 27.02GHz to 28.57GHz. To validate the analysis results, prototype of the designed slot antennas array is fabricated. Characteristics of the slot antennas array are measured and compared with the analysis results.

We developed a mantle-cloak antenna by controlling the surface reactance of a dielectric-loaded dipole antenna. First, a mantle-cloak antenna with an assumed ideal metasurface sheet was designed, and band rejection characteristics were obtained by controlling the surface reactance of the mantle cloak. The variable range of the frequency spacing between the operating and stopband frequencies of the antenna was clarified by changing the value of the surface reactance. Next, a mantle-cloak antenna that uses vertical strip conductors was designed to clarify the characteristics and operating principle of the antenna. It was confirmed that the stopband frequency was 1130MHz, and the proposed antenna had a 36.3% bandwidth (|S11| ≤ -10dB) from 700 to 1010MHz. By comparing the |S11| characteristics and the input impedance characteristics of the proposed antenna with those of the dielectric-loaded antenna, the effect of the mantle cloak was confirmed. Finally, a prototype of the mantle-cloak antenna that uses vertical strip conductors was developed and measured to validate the simulation results. The measurement results were consistent with the simulation results.

This paper introduces a high-resolution and compact CMOS switch-type phase shifter (STPS) for the 5th generation mobile network (5G) n260 band. In this work, totally four coarse phase shifting stages and a high-resolution tuning stage are included. The coarse stages based on the bridged-T topology is capable of providing 202.5° phase coverage with a 22.5° tuning step. To further improve the phase shifting resolution, a compact fine-tuning stage covering 23° is also integrated with the coarse stages. Sub-degree phase shifting resolution is realized for supporting the fine beam-steering and high-accuracy phase calibration in the 5G new radio. Simplified phase control algorithm and suppressed insertion loss can also be maintained by the proposed fine-tuning stage. In the measurement, the achieved RMS gain errors at 39 GHz are 0.1 dB and 0.4 dB for the coarse stages and fine stage, respectively. The achieved RMS phase errors at 39 GHz are 3.1° for the coarse stages and 0.1° for the fine stage. Within 37 GHz to 40 GHz, the measured return loss within all phase-tuning states is always better than -14 dB. The proposed phase shifter consumes a core area of only 0.12mm2 with 65-nm CMOS process, which is area-efficient.

The newly proposed orthogonal time frequency space (OTFS) system exhibits excellent error performance on high-Doppler fading channels. However, the rectangular prototype window function (PWF) inherent in OTFS leads to high out-of-band emission (OOBE), which reduces the spectral efficiency in multi-user scenarios. To this end, this paper presents an OTFS system based on bi-orthogonal frequency division multiplexing (OTFS-BFDM) modulation. In OTFS-BFDM systems, PWFs with bi-orthogonal properties can be optimized to provide lower OOBE than OTFS, which is a special case with rectangular PWF. We further derive that the OTFS-BFDM system is sparsely-connected so that the low-complexity message passing (MP) decoding algorithm can be adopted. Moreover, the power spectral density, peak to average power ratio (PAPR) and bit error rate (BER) of the OTFS-BFDM system with different PWFs are compared. Simulation results show that: i) the use of BFDM modulation significantly inhibits the OOBE of OTFS system; ii) the better the frequency-domain localization of PWFs, the smaller the BER and PAPR of OTFS-BFDM system.

This paper introduces several design techniques to improve the performance of CMOS frequency multipliers that operate at the sub-THz band without increasing the complexity and the power consumption of the circuit. The proposed techniques are applied to a device nonlinearity-based frequency tripler and to a push-push frequency doubler. By utilizing the fundamental and second harmonic feedback cancellation, the tripler achieves -2.9dBm output power with a simple single-ended circuit architecture reducing the required area and power consumption. The tripler operates at frequencies from 103GHz to 130GHz. The introduced modified push-push doubler provides 2.3dB conversion gain including the balun losses and it has good tolerance against balun mismatches. The output frequency of the doubler is from 118GHz to 124GHz. Both circuits were designed and fabricated using CMOS 65nm technology.

In flat panel display (FPD) lithography, a high resolution and large depth of focus (DOF) are required. The demands for high throughput have necessitated the use of large glass plates and exposure areas, thereby increasing focal unevenness and reducing process latitude. Thus, a large DOF is needed, particularly for high-resolution lithography. To manufacture future high-definition displays, 1.0μm line and space (L/S) is predicted to be required, and a technique to achieve this resolution with adequate DOF is necessary. To improve the resolution and DOF, resolution enhancement techniques (RETs) have been introduced. RETs such as off-axis illumination (OAI) and phase-shift masks (PSMs) have been widely used in semiconductor lithography, which utilizes narrowband illumination. To effectively use RETs in FPD lithography, modification for broadband illumination is required because FPD lithography utilizes such illumination as exposure light. However, thus far, RETs for broadband illumination have not been studied. This study aimed to develop techniques to achieve 1.0μm L/S resolution with an acceptable DOF. To this end, this paper proposes a method that combines our previously developed RET, namely, divided spectrum illumination (DSI), with an attenuated PSM (Att. PSM). Theoretical observations and simulations present the design of a PSM for broadband illumination. The transmittance and phase shift, whose degree varies according to the wavelength, are determined in terms of aerial image contrast and resist loss. The design of DSI for an Att. PSM is also discussed considering image contrast, DOF, and illumination intensity. Finally, the exposure results of 1.0μm L/S using DSI and PSM techniques are shown, demonstrating that a PSM greatly improves the resist profile, and DSI enhances the DOF by approximately 30% compared to conventional OAI. Thus, DSI and PSMs can be used in practical applications for achieving 1.0μm L/S with sufficient DOF.

In-band full-duplex (IBFD) has been an attractive technology, which can theoretically double the spectral efficiency. However, when performing IBFD in the dynamic-duplex cellular (DDC) system, inter-user interference (IUI) deteriorates transmission performance in downlink (DL) communication and limits IBFD-applicable area and IBFD application ratio. In this paper, to expand the IBFD-applicable area and improve the IBFD application ratio, we propose an IUI reduction scheme using successive interference cancellation (SIC) for the DDC system. SIC can utilize the power difference and reduce the signal with the higher power. The effectiveness of the proposed scheme is evaluated by the computer simulation. The IUI reducing effect on the IBFD-inapplicable area is confirmed when the received power of the IUI is stronger than that of the desired signal at the user equipment for DL (DL-UE). The IBFD-inapplicable area within 95m from the DL-UE, where the IBFD does not work without the proposed scheme, can reduce by 43.6% from 52.8% to 9.2% by applying the proposed scheme. Moreover, the IBFD application ratio can improve by 24.6% from 69.5% to 94.1%.

Coprime (pair of) DFT filter banks (coprime DFTFB), which process signals like a spectral analyzer in time domain, divides the power spectrum equally into MN bands by employing two DFT filter banks (DFTFBs) of size only M and N respectively, where M and N are coprime integers. With coprime DFTFB, frequencies in wide sense stationary (WSS) signals can be effectively estimated with a much lower sampling rates than the Nyquist rates. However, the imperfection of practical FIR filter and the correlation based detection mode give rise to two kinds of spurious peaks in power spectrum estimation, that greatly limit the application of coprime DFTFB. Through detailed analysis of the spurious peaks, this paper proposes a modified spectral analyzer based on dual coprime DFTFBs and sub-decimation, which not only depresses the spurious peaks, but also improves the frequency estimation accuracy. The mathematical principle proof of the proposed spectral analyzer is also provided. In discussion of simultaneous signals detection, an O-extended MN-band coprime DFTFB (OExt M-N coprime DFTFB) structure is naturally deduced, where M, N, and O are coprime with each other. The original MN-band coprime DFTFB (M-N coprime DFTFB) can be seen a special case of the OExt M-N coprime DFTFB with extending factor O equals ‘1’. In the numerical simulation section, BPSK signals with random carrier frequencies are employed to test the proposed spectral analyzer. The results of detection probability versus SNR curves through 1000 Monte Carlo experiments verify the effectiveness of the proposed spectrum analyzer.

We present a novel circularly polarized ring microstrip antenna and its design. The shorting pins discretely disposed on the inner edge of the ring microstrip antenna are introduced as a new degree of freedom for improving the resonance frequency control. The number and diameter of the shorting pins control the resonance frequency; the resonance frequency can be almost constant with respect to the inner/outer diameter ratio, which expands the use of the ring microstrip antenna. The dual-band antenna where the proposed antenna includes another ring microstrip antenna is designed and measured, and simulated results agree well with the measured one.

This paper presents an X-band power-combined pulsed high power amplifier (HPA) based on the low insertion loss waveguide combiner. Relationships between the return loss and isolation of the magic Tee (MT) have been analyzed and the accurate design technique is given. The combination network is validated by the measurement of a single MT and a four-way passive network, and the characterization of the combined HPA module is designed, fabricated and discussed. The HPA delivers 200W output power with an associated power-added efficiency close to 40% within the frequency range of 7.8 GHz to 12.3 GHz. The combination efficiency is higher than 93%.