Low-temperature bonding methods of optoelectronic chips, such as laser diodes (LD) and photodiode (PD) chips, have been the focus of much interest to develop highly functional and compact optoelectronic devices, such as microsensors and communication modules. In this paper, room-temperature bonding of the optoelectronic chips with Au thin film to coined Au stud bumps with smooth surfaces (Ra: 1.3nm) using argon and hydrogen gas mixture atmospheric-pressure plasma was demonstrated in ambient air. The die-shear strength was high enough to exceed the strength requirement of MIL-STD-883F, method 2019 (×2). The measured results of the light-current-voltage characteristics of the LD chips and the dark current-voltage characteristics of the PD chips indicated no degradation after bonding.

Fan-in/fan-out devices are necessary for the construction of multi-core fiber communication systems. A fan-out device using a capillary is proposed and made by connecting a tapered fiber bundle and a multi-core fiber. The tapered fiber bundle is elongated so that the core arrangement and the mode field diameter (MFD) of single-core fibers agree with those of the multi-core fiber. Suppressing the MFD change is necessary to reduce the coupling loss of the fan-out device. While elongating the fiber bundle, the MFD decreases at the beginning until the core reaches a certain core diameter, and then it begins to increase. We suppress the MFD change of the fan-out device by using this phenomenon. The average insertion loss at both ends of a multi-core fiber was approximately 1.6dB when the fabricated fan-in/fan-out devices were connected to the multi-core fiber.

A connector model expressed as an inductance is proposed for use in a previously reported common-mode antenna model. The common-mode antenna model is an equivalent model for estimating only common-mode radiation from a printed circuit board (PCB) more quickly and with less computational resources than a calculation method that fully divides the entire structure of the PCB into elemental cells, such as narrow signal traces and thin dielectric layers. Although the common-mode antenna model can estimate the amount of radiation on the basis of the pin configuration of the connector between two PCBs, the calculation results do not show the peak frequency shift in the radiation spectrum when there is a change in the pin configuration. A previous study suggested that the frequency shift depends on the total inductance of the connector, which led to the development of the connector model reported here, which takes into account the effective inductance of the connector. The common-mode antenna model with the developed connector model accurately simulates the peak frequency shift caused by a change in the connector pin configuration. The results agree well with measured spectra (error of 3 dB).

Many selected mapping (SLM) schemes have been proposed to reduce the peak-to-average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signal sequences. In this paper, an efficient selection (ES) method of the OFDM signal sequence with minimum PAPR among many alternative OFDM signal sequences is proposed; it supports various SLM schemes. Utilizing the fact that OFDM signal components can be sequentially generated in many SLM schemes, the generation and PAPR observation of the OFDM signal sequence are processed concurrently. While the u-th alternative OFDM signal components are being generated, by applying the proposed ES method, the generation of that alternative OFDM signal components can be interrupted (or stopped) according to the selection criteria of the best OFDM signal sequence in the considered SLM scheme. Such interruption substantially reduces the average computational complexity of SLM schemes without degradation of PAPR reduction performance, which is confirmed by analytical and numerical results. Note that the proposed method is not an isolated SLM scheme but a subsidiary method which can be easily adopted in many SLM schemes in order to further reduce the computational complexity of considered SLM schemes.

This study proposes a novel resonator design that uses tightly coupled parallel coils to improve the quality factor (Q factor) in coupled magnetic resonance wireless power transfer. Depending on the characteristics of the tightly coupled parallel-connected coils, the proposed resonator can offer significantly reduced resistance with very little self-inductance loss. A double-layer spiral coil structure is used for resonator design and evaluating its characteristics. Measured results show that a resonator consisting of two identical, tightly coupled parallel double-layer spiral coils can match the Q factor of a conventional double-layer spiral coil with the same number of turns, even though its equivalent resistance is approximately 75% less. Moreover, the system power transfer performance of the resonator was measured under the impedance matching condition. To further reduce the resistance, we propose another resonator comprising of three parallel and tightly coupled double-layer spiral coils, and measure its equivalent resistance characteristics for different wire gap sizes.

We have proposed a quality of experience (QoE)-oriented wireless local area network (WLAN) to provide sufficient QoE to important application flows. Unlike ordinary IEEE 802.11 WLAN, the proposed QoE-oriented WLAN dynamically performs admission control with the aid of the prediction of a “loadable capacity” criterion. This paper proposes an algorithm for dynamic network reconfiguration by centralized control among multiple basic service sets (BSSs) of the QoE-oriented WLAN, in order to maximize the number of traffic flows whose QoE requirements can be satisfied. With the proposed dynamic reconfiguration mechanism, stations (STAs) can change access point (AP) to connect. The operating frequency channel of a BSS also can be changed. These controls are performed according to the current channel occupancy rate of each BSS and the required radio resources to satisfy the QoE requirement of the traffic flow that is not allowed to transmit its data by the admission control. The effectiveness of the proposed dynamic network reconfiguration is evaluated through indoor experiments with assuming two cases. One is a 14-node experiment with QoE-oriented WLAN only, and the other is a 50-node experiment where the ordinary IEEE 802.11 WLAN and the QoE-oriented WLAN coexist. The experiment confirms that the QoE-oriented WLAN can significantly increase the number of traffic flows that satisfy their QoE requirements, total utility of network, and QoE-satisfied throughput, which is the system throughput contributing to satisfy the QoE requirement of traffic flows. It is also revealed that the QoE-oriented WLAN can protect the traffic flows in the ordinary WLAN if the border of the loadable capacity is properly set even in the environment where the hidden terminal problem occurs.

The new generation video standard, i.e., High-efficiency Video Coding (HEVC), shows a significantly improved efficiency relative to the last standard, i.e., H.264. However, the quad tree structured coding units (CUs), which are adopted in HEVC to improve compression efficiency, cause high computational complexity. In this study, a novel fast algorithm is proposed for CU partition in intra coding to reduce the computational complexity. A rough minimum depth prediction of the largest CU method and an early termination method for CU partition based on the total coding bits of the current CU are employed. Many approaches have been proposed to reduce the encoding complexity of HEVC, but these methods do not use the total coding bits of the current CU as the main basis for judgment to judge the CU complexity. Compared with the reference software HM16.6, the proposed algorithm reduces encoding time by 45% on average and achieves an approximately 1.1% increase in Bjntegaard delta bit rate and a negligible peak signal-to-noise ratio loss.

This paper presents a practical system which allows instructors to easily introduce 3D games utilizing smartphones in a classroom. The system consists of a PC server, a big screen and smartphone clients. The server provides 3D models, so no 3D authoring is needed when using this system. For an instructor, preparing slides of quiz-questions with the correct answers is all that is required when designing 3D games. According to a quiz specified by an instructor, this system constructs a corresponding 3D game scene. The answers students provide on their smartphones will be used to play this game. Everyone in the classroom can see this 3D game in real time on a big screen. The game illustrates how every student has reacted to a quiz. This system also introduces specialized queues for mobile interactions; a queue for commands from an instructor and a queue for data from students. The command queue has higher priority than the data queue; so that an instructor can control this system by sending commands with clicks on a smartphone. Previous studies have mostly provided specially designed teaching materials to instructors, often treating them as passive consultants. However, by using slides, already familiar to instructors, this system enables instructors to combine their own teaching materials with 3D games in the classroom. Moreover, 3D games are expected to further motivate students to actively participate in classroom activities. This system is evaluated in this paper.

Workflow nets (WF-nets for short) are a mathematical model of real world workflows. A WF-net is often updated in accordance with the change of real world. This may cause places that are redundant from the viewpoint of the behavior. Such places are called implicit. We first proposed a necessary and sufficient condition to find implicit places. Then we proved that removing of implicit places is a reduction operation which forms branching bisimilarity. We also constructed an algorithm for the reduction. Next, we applied the proposed reduction operation to WF-net refactoring. Then we showed the usefulness of the proposed refactoring with two examples.

Aiming to solve the input/output (I/O) bottleneck concerning next-generation interconnections, 5×5-millimeters-squared silicon-photonics-based chip-scale optical transmitters/receivers (TXs/RXs) — called “optical I/O cores” — were developed. In addition to having a compact footprint, by employing low-power-consumption integrated circuits (ICs), as well as providing multimode-fiber (MMF) transmission in the O band and a user-friendly interface, the developed optical I/O cores allow common ease of use with applications such as multi-chip modules (MCMs) and active optical cables (AOCs). The power consumption of their hybrid-integrated ICs is 5mW/Gbps. Their high-density user-friendly optical interface has a spot-size-converter (SSC) function and permits the physical contact against the outer waveguides. As a result, they provide large enough misalignment tolerance to allow use of passive alignment and visual alignment. In a performance test, they demonstrated 25-Gbps/ch error-free operation over 300-m MMF.

This paper proposes a novel image integral equation of the first type (IIE-1) for a TE plane wave scattering from periodic rough surfaces with perfect conductivity by means of the method of image Green's function. Since such an IIE-1 is valid for any incident wavenumbers including the critical wavenumbers, the analytical properties of the scattered wavefield can be generally and rigorously discussed. This paper firstly points out that the branch point singularity of the bare propagator inevitably appears on the incident wavenumber characteristics of the scattered wavefield and its related quantities just at the critical wavenumbers. By applying a quadrature method, the IIE-1 becomes a matrix equation to be numerically solved. For a periodic rough surface, several properties of the scattering are shown in figures as functions of the incident wavenumbers. It is then confirmed that the branch point singularity clearly appears in the numerical solution. Moreover, it is shown that the proposed IIE-1 gives a numerical solution satisfying sufficiently the optical theorem even for the critical wavenumbers.

Verification of temporal logic properties plays a crucial role in proving the desired behaviors of continuous systems. In this paper, we propose an interval method that verifies the properties described by a bounded signal temporal logic. We relax the problem so that if the verification process cannot succeed at the prescribed precision, it outputs an inconclusive result. The problem is solved by an efficient and rigorous monitoring algorithm. This algorithm performs a forward simulation of a continuous-time dynamical system, detects a set of time intervals in which the atomic propositions hold, and validates the property by propagating the time intervals. In each step, the continuous state at a certain time is enclosed by an interval vector that is proven to contain a unique solution. We experimentally demonstrate the utility of the proposed method in formal analysis of nonlinear and complex continuous systems.

Accidental falling among elderly people has become a public health concern. Thus, there is a need for systems that detect a fall when it happens. This paper presents a portable real-time remote health monitoring system that can remotely monitor patients' movements. The system is designed and implemented using ZigBee wireless technologies, and the data is analysed using Matlab. The purpose of this research is to determine the acceleration thresholds for fall detection, using tri-axial accelerometer readings at the head, waist, and knee. Seven voluntary subjects performed purposeful falls and Activities of Daily Living (ADL). The results indicated that measurements from the waist and head can accurately detect falls; the sensitivity and reliability measurements of fall detection ranged between 80% and 90%. In contrast, the measurements showed that the knee is not a useful position for the fall detection.

Random forest regressor has recently been proposed as a local landmark estimator in the face alignment problem. It has been shown that random forest regressor can achieve accurate, fast, and robust performance when coupled with a global face-shape regularizer. In this paper, we extend this approach and propose a new Local Forest Classification and Regression (LFCR) framework in order to handle face images with large yaw angles. Specifically, the LFCR has an additional classification step prior to the regression step. Our experiment results show that this additional classification step is useful in rejecting outliers prior to the regression step, thus improving the face alignment results. We also analyze each system component through detailed experiments. In addition to the selection of feature descriptors and several important tuning parameters of the random forest regressor, we examine different initialization and shape regularization processes. We compare our best outcomes to the state-of-the-art system and show that our method outperforms other parametric shape-fitting approaches.

In this paper, an iterative optimal method is proposed to design the prototype filters for a fast filter bank (FFB) with low complexity, aiming to control the optimum ripple magnitude tolerance of each filter according to the overall specifications. This problem is formulated as an optimization problem for which the total number of multiplications is to be minimized subject to the constrained ripple in the passband and stopband. In the following, an iterative solution is proposed to solve this optimization problem for the purpose of obtaining the impulse response coefficients with low complexity at each stage. Simulations are conducted to verify the performance of the proposed scheme and show that compared with the original method, the proposed scheme can reduce about 24.24% of multiplications. In addition, the proposed scheme and the original method provide similar mean square error (MSE) and the mean absolute error (MAE) of the frequency response.

Purchase behavior prediction is one of the most important issues for the precision marketing of e-commerce companies. This Letter presents our solution to the purchase behavior prediction problem in E-commerce, specifically the task of Big Data Contest of China Computer Federation in 2014. The goal of this task is to predict which users will have the purchase behavior based on users' historical data. The traditional methods of recommendation encounter two crucial problems in this scenario. First, this task just predicts which users will have the purchase behavior, rather than which items should be recommended to which users. Second, the large-scale dataset poses a big challenge for building the empirical model. Feature engineering and Factorization Model shed some light on these problems. We propose to use Factorization Machines model based on the multiple classes and high dimensions of feature engineering. Experimental results on a real-world dataset demonstrate the advantages of our proposed method.

Microwave systems have a number of promising applications in surveillance and monitoring systems. The main advantage of microwave systems is their ability to detect targets at distance under adverse conditions such as dim, smoky, and humid environments. Specifically, the wide bandwidth of ultra-wideband radar enables high range resolution. In a previous study, we proposed an accurate shape estimation algorithm for multiple targets using multiple ultra-wideband Doppler interferometers. However, this algorithm produces false image artifacts under conditions with severe interference. The present paper proposes a technique to suppress such false images by detecting inconsistent combinations of the radial velocity and time derivative of image positions. We study the performance of the proposed method through numerical simulations of a two-dimensional section of a moving human body, and demonstrate the remarkable performance of the proposed method in suppressing false image artifacts in many scenarios.

This paper describes a fast and effective algorithm for refining the parameter estimates of multicomponent third-order polynomial phase signals (PPSs). The efficiency of the proposed algorithm is accompanied by lower signal-to-noise ratio (SNR) threshold, and computational complexity. A two-step procedure is used to estimate the parameters of multicomponent third-order PPSs. In the first step, an initial estimate for the phase parameters can be obtained by using fast Fourier transformation (FFT), k-means algorithm and three time positions. In the second step, these initial estimates are refined by a simple moving average filter and singular value decomposition (SVD). The SNR threshold of the proposed algorithm is lower than those of the non-linear least square (NLS) method and the estimation refinement method even though it uses a simple moving average filter. In addition, the proposed method is characterized by significantly lower complexity than computationally intensive NLS methods. Simulations confirm the effectiveness of the proposed method.

In this paper, we derive two simple asymptotic closed-form formulas for the average bit error probability (BEP) of differential quaternary phase shift keying (DQPSK) with Gray encoding and a simple asymptotic approximation for the average symbol error probability (SEP) of doubly-differential quaternary phase shift keying (DDQPSK) in Nakagami-m fading channels. Compared with the existing BEP/SEP expressions, the derived concise formulas are much more effective in evaluating the asymptotic properties of DQPSK/DDQPSK with various Nakagami fading parameters, the accuracy of which is verified by extensive numerical results.

Unsupervised spoken unit discovery or zero-source speech recognition is an emerging research topic which is important for spoken document analysis of languages or dialects with little human annotation. In this paper, we extend our earlier joint training framework for unsupervised learning of discrete density HMM to continuous density HMM (CDHMM) and apply it to spoken unit discovery. In the proposed recipe, we first cluster a group of Gaussians which then act as initializations to the joint training framework of nonnegative matrix factorization and semi-continuous density HMM (SCDHMM). In SCDHMM, all the hidden states share the same group of Gaussians but with different mixture weights. A CDHMM is subsequently constructed by tying the top-N activated Gaussians to each hidden state. Baum-Welch training is finally conducted to update the parameters of the Gaussians, mixture weights and HMM transition probabilities. Experiments were conducted on word discovery from TIDIGITS and phone discovery from TIMIT. For TIDIGITS, units were modeled by 10 states which turn out to be strongly related to words; while for TIMIT, units were modeled by 3 states which are likely to be phonemes.