In improving channel utilization in microcellular systems, adaptive channel allocation using distributed control has been reported to be effective. We describe an analytical approximation algorithm for channel dimensioning of distributed adaptive channel allocation. We compare our analytical results with simulation results and show the characteristics of permissible load as a function of the number of base station channels based on our method. Finally we illustrate traffic design and administration based on our algorithm.

In this paper, we propose an efficient method (called DIRIC algorithm) to allocate carrier frequencies so as to minimize intermodulation products in two-level SCPC systems in which Hub station and many Remote stations communicate each other through satellite transponder. We also present a very efficient method to evaluate intermodulation products with substantially reduced CPU time in two-level SCPC systems. We compare and analyze the performance of several frequency allocation methods to extend DELINS-INSDEL algorithm (which is proposed by Okinaka) to two-level SCPC systems. When the proposed algorithm is applied to systems with modulated carrier, it is verified that this algorithm has the same efficiency as the unmodulated carrier. It is also shown heuristically that certain initial assignment algorithms perform better than random assignment.

A key element in the CDMA transmission is DS spreading. Spreading in a DS/SSMA system are provided in two categories-synchronization and data. For synchronization sequences, good auto-correlation and cross-correlation properties are required in order to guarantee fast acquistion with a minimum false alarm probability. On the other hand, the auto-correlation property may not be so important in data spreading since synchronization is obtained by synchronization spreading. In this paper we provide a set of synchronization sequences and a set of data sequences--each a set of binary N-tuples--that have the necessary correlation constraints.

We propose a nonlocal impact ionization model applicable for the drain region where electric field increases exponentially. It is expressed as a function of an electric field and a characteristic length which is determined by a thickness of gate oxide and a source/drain junction depth. An analytical substrate current model for n-MOSFET is also derived from the new nonlocal impact ionization model. The model well explains the reason why the theoretical characteristic length differs from empirical expressions used in a pseudo two-dimensional model for MOSFET's. The nonlocal impact ionization model implemented in a device simulator demonstrates that the new model can predict substrate current correctly in the framework of drift-diffusion model.

A flexible and low-cost menagement technology is desired for fabrication line of both ASICs and cutting edge LSIs. To meet such desire, a management technology named "super operator shifts" has been proposed. After taking operator's skill level into consideration, an ASIC line manager can stretch line working time by use of the super operator shifts. It results that he can successfully get 3-shifts turn around time for severe-delivery-date lots with a payment equal to about 2-shifts line-cost.

A scalable and flexible ASIC CIM system distributed on UNIX workstations, ORCHARD , has been developed. It is designed from three viewpoints: (1) cost and TAT reduction in system construction, (2) flexibility in data management for quality control, and (3) precise and quick scheduling and effective lot tracking to control TAT for each lot. The concept of a "virtual machine" is introduced to connect equipment having various protocols to a host system. The virtual machine is automatically generated at an average automatic generation ratio of as high as 89%, which leads to a reduction in cost and TAT in system construction. Data for quality control is managed by changing flexibly the "data processing recipe." This recipe defines screen format, data collected from equipment, and data transfered from various databases. Precise scheduling of lots with various levels of priority is achieved by introducing a priority evaluation function, thereby reducing scheduling time to 1/20 that for manual scheduling.

In this paper, an electrostatic actuator with electret is proposed. Electrets are the electrical equivalent of magnets. They are dielectric's carrying a non equilibrium permanent space charge or polarization distribution. This distribution can create either an external electric field or internal properties such as piezo or pyroelectricity. In the first case it is possible to make new types of electrostatic actuators by the external electric field. An electrostatic relay with electret is fabricated to demonstrate the possibility of an electrostatic actuator with electret. The size of relay is 5.2 mm11.5 mm. Its amature beam is 50 µm thick, 2.9 mm wide, 6.3 mm long, and acts as a moving electrode. Facing it, the stationary electrode is 20 µm away from the moving electrode. On the stationary electrode, new type of electret made from SiO2 is deposited. We have succeeded in making the armature operate at low applied voltage 20 V. On the same structure without electret, we need more than 120 V to make the same armature operation. We have also succeeded in making the armature latching.

We present a design chart and a manufacturing process for mm-wave absorber consisting of two spacers (poly-carbonate) and two-resistive sheets (polyethylene terephthalate deposited with Indium Tin Oxide). The conventional design chart gives us necessary information to make a desirable absorber. Based on the design chart, a multi-layered type absorber was manufactured and it is concluded that a significant absorption level (-20dB) is attained at a wide-frequency range of 46-66GHz.

This paper presents a new microprocessing method that uses a Cl2 fast atom beam (FAB) with stainless steel (SUS304) patterned masks. This new method uses the patterned mask instead of lithographically processed patterned photoresist materials employed in the conventional FAB microprocessing method. We examined the performance of this method by etching GaAs workpieces under various conditions: (1) by setting the distance between the mask surface and flat workpiece surface, L, from 0 µm to 500 µm; (2) by setting the angle between the FAB axis and the flat workpiece surface, θ; to either 30or 50. (3) by etching a workpiece surface that had a 15-µm step and two different surface textures, smooty and undulated; and (4) by doing overlapped etching using a square-patterned mask first and then a circular-patterned mask. The experiments show that the accuracy of reproducing the mask pattern on the etched surface increases with decreasing L. Moreover, the etching rate is almost the same (L100 µm) and decreases slightly at longer distance (L100 µm). The experiments also show that the side walls of the surface are parallel to the FAB axis, even for θ0, indicating that anisotropic etching can be achieved. The experiments for the stepped surface with different surface textures show the surface texture is not affected by the FAB etching. The overlapped etching experiments show that FAB etching is capable of producing overlapped structures. These results demonstrate that this new FAB method can be used in the microproduction of multi-faced, overlapped, three-dimensional microstructures.

A composite noise generator (CNG) is proposed for simulating the actual non-Gaussian noise and its applications are mentioned. Basing upon the actual measured result (APD) of induced noise from electric contact discharge arc, the APD is approximated by partial linearlization and shown that it can be simulated by a combination of plural Gaussian noise sources. Applying the CNG, quasi-peak (Q-P) detector is investigated and shown that the Q-P detector response is different for non-Gaussian noise when its time domain parameter is different even if its original APD is the same. For digital transmission error due to non-Gaussian noise, and for TV picture stained by the non-Gaussian noise, the CNG is applied to evaluate their performances and quality. The results obtained show that the CNG can be used as a standard non-Gaussian generator for several immunity tests for information equipments.

The analysis of the shielding properties of a planar wire-mesh shield embedded in a general isotropic--chirality is included--or anisotropic stratified media is here presented. A suitable model of the grating has been introduced in order to consider the occuring phenomena, in fact through a spectral technique the electromagnetic problem is translated into the equivalent circuit network model that allows to express the time response of the shielded field for the NEMP incidence in a closed form.

The precise phase characteristics of the reflected and transmitted waves are obtained for electromagnetic scattering by inductive discontinuities of finite thickness located in rectangular waveguides. The incident wave is assumed to be the dominant mode, and the modified residue-calculus method is used for numerical analysis. The phase characteristics when the thickness and width of the iris are varied, and characteristics of the reflected and transmitted waves when resonance appears, are discussed. In addition, an X-band experiment is performed and the calculations for both the reflected and transmitted waves are shown to agree well with the experimental values.

For estimating the radiated emission from a metallic enclosure, the authors have developed a numerical computational method which applied inverse analysis. A metallic enclosure containing a loop antenna was set up to be a model source for the numerical analysis. Magnetic fields around the enclosure were measured by measurement systems fabricated in the authors' laboratory. Using the measured magnetic fields, current distributions on the enclosure surface were determined by means of an inverse analysis utilizing the least squares method. From this surface current distribution, the electromagnetic field distributions were estimated by forward analysis on a cylindrical surface 3.0m in radius. The amount of the error in the estimated fields distribution was also discussed.

We developed piezoresistors with an intrinsic compensation of the offset temperature characteristics. High energy ion implantation was applied to fabricate this type of piezoresistor. The dopant profile of the buried piezoresistor resembles to that of the junction gate field effect transistor (JFET). The buried layer corresponds to a channel of JFET, and the substrate bias corresponds to the gate voltage. Owing to the independent temperature varying parameters, i.e., width of the depletion layer and carrier mobility in the channel, the drain current of the JFET has a temperature independent point at an appropriate gate source voltage. The effect was used in the new type of buried piezoresistor which has a driving point of zero temperature coefficient of resistance at an appropriate gate source voltage.

Although electromagnetic analysis tools can provide good numerical data about the effects of electromagnetic interference, measurements are the method of choice for obtaining quantitative, accurate data on electromagnetic noise problems. Furthermore, since electromagnetic interference measurements often provide the only data accepted by most regulatory agencies, the measurements and their accuracies have recently become a very important issue in order to regulate and harmonize various electromagnetic compatibility emission and immunity standards. The measurement techniques and instrumentations of most use for making accurate electromagnetic interference measurements are presented in this paper.

On mutually coupling lines, the transmission signal is dispersively propagated by crosstalk coupling between lines and shows complex propagation characteristics caused by reciprocal reflections. Usually, the differential equation and the integral equation have been applied to analyze the solutions of transmission lines. In this paper, we propose a different analytical method of the propagation characteristics of signal and crosstalk noise. By setting up crosstalk coupling line as a sectionally divided digital transmission network and by using the signal flow graph and the difference equation, the propagation characteristics in the frequency domain, the space domain and the time domain on mutually coupling lines can be obtained. To verify the validity of this method and analyze the complex propagation problems, we first study the crosstalk characteristics of a twisted pair cable via the third circuit by unidirectional coupling. Subsequently we will analyze the coupling theory of bidirectional coupling lines.

The wave forms of electric and magnetic fields radiated by short gap discharges are measured to analyze electrostatic discharge (ESD) events in the near-field zone with the monopole antennas, the loop antenna and the 5.5GHz bandwidth waveform digitizer. The antenna outputs are corrected by the measured characteristics of the antennas. The relations between the measured electric field and the discharge currents are discussed.

The potential attenuation process of charged human body (HB) is analyzed. A two-dimensional circuit model is presented for predicting the potential attenuation characteristics of the HB charged on the floor. The theoretical equation for the HB potential is derived in the closed form in the Laplacian transformation domain, and the numerical inverse Laplace transform is used to compute it. The half-life or relaxation time of the HB potential for decay is numerically examined with respect to the electrical parameters of shoes. The experiment is also conducted for verifying the validity of the computed result.

The objective of this study is to realize a manipulator of 0.5 mm in outside diameter as a part of 'research and development of micro machine technology.' This manipulator is intended as a part of a working robot to fix or observe the inside wall of a small pipe. One of the important problems of this research is to establish a processing method of a tubular small structure. MIM, metal injection molding, has been adopted to fabricate such a small structure. As a processing method to machine small molds for MIM, finish processing with surface roughness of Rmax 0.1 µm has been under our research applying 'vibrational processing technology,' which was developed on our own. This paper presents the results of 'vibrational processing technology' surface finishing of molds for metal injection.

A black membrane is a biological-membrane analogue, i.e. a phospholipid bilayer membrane, artificially formed on an orifice immersed in water. It is used to investigate the properties of the membrane itself and channels embedded therein. In this paper, microfabrication techniques are applied to fabricate the orifice, and a glass substrate is isotropically etched to define the orifice geometry. The periphery of the orifice was patterned with aminosilane to anchor the membrane. The remainder part was coated with fluorosilane to make the surface hydrophobic and to prevent adsorption of channel-forming molecules. We demonstrated experimentally that a stable and reproducible membrane is easily obtainable using the orifice.