We have studied in detail the effect of gas flow rates on the film properties of low-temperature (300) polycrystalline silicon (poly-Si) films prepared by conventional plasma enhanced chemical vapor deposition (13.56 MHz) with SiF4/SiH4/H2 gases. The effect of SiH4 flow rate on crystallization is shown to be large. A small amount of SiH4 with high SiF4 and H2 flow rates (50[H2]/[SiH4]1200, 20[SiF4]/[SiH4]150, 1[H2]/[SiF4]16) is important to form poly-Si films. The poly-Si films deposited under such optimized conditions had shown preferential 〈110〉-orientation and the crystalline fraction is estimated to be more than 80%. The deposition rates are in the range of 5-30 nm/min. The conductivity is in the range of 10-8-10-6 S/cm. Further, the electrical conduction indicates an activation type, and the activation energy is in the range of 0.5-0.6 eV.

Tomita's parsing method (GLR) is a practical and successful parsing method for natural language. However, one difficulty in the GLR is that interleaved constraint processing of syntax and semantics in parallel is not trivial during parsing, because it uses the precompiled table for a fast real-time parsing. In this paper, we present a method which makes the GLR adaptable to interleaved parsing while making some limitation on its generality. For interleaved parsing, the conflicts of the LR parsing table must be resolved at the parse time. The shift-reduce conflict among the above conflicts is the most serious one for interleaved parsing because of the lack of knowledge for the conflict resolution at the parse time. Therefore, we concentrate on resolving a shift-reduce conflict by introducing a grammar which is called a shift-first LR (k) grammar. Our method for this is that the conflict resolution is delayed by the shift-first strategy which makes an unconditional choice of shift actions in the case of a shift-reduce conflict. Then, a delayed resolution that resolves the conflict, is made. Depending on the decision of the resolution, the pseudo parsing, which parses symbols in the LR parser stack, proceeds. Our experiments showed that our parser is efficient while attaining the interleaved parsing at real time.

Dynamic programming based one dimensional-two dimensional adaptive pattern matching methods were investigated. In these methods, the reference pattern is represented as a sequence of directional vectors and the input pattern as two dimensional dot pattern. The input pattern needs no preskeletization or local feature analysis, and thus stroke order free top-down pattern matching is carried out. As the starting point, Rubber String Matching algorithm using fixed direction vectors was newly investigated. At latter stages, the reference pattern vectors were permitted some freedom in their directions to cope with abrupt aberrations in input pattern line segments, improving the flexibility of matching. Two cases were considered, allowing 45and approximately 20deviations from the vector directions. The 20version gave the best recognition score.

A method for evaluating the degradation of subband adaptive digital filters (ADF) is presented. The performance of a simple ADF that uses critical sampling is mainly influenced by the subband filter bank's characteristics and the finite precision arithmetic operations used. This paper considers a two-channel mirror filter bank and a normalized least mean square algorithm with floating point arithmetic. The theoretical ERLE (Echo Return Loss Enhancement) and the theoretical relationships between the output error of the ADF and the circuit parameters considering finite precision A/D conversion and finite word length effects in floating point arithmetic operation are obtained using an equivalent noise model. Simulation results are found to be in good agreement to analytical values; the difference is only 3 to 5 dB.

This paper presents a new approach to the recovery of 3-D structure from multiple pairs of images from different viewpoints. Searching for the corresponding points between images, which is common in stereopsis, is avoided. Extracted edges from input images are projected back into 3-D space, and their intersections are calculated directly. Many false intersections may appear, but if we have many pair images, true intersections are extracted by appropriate thresholding. Octree representation of the intersections enables this approach. We consider a way to treat adjacent edge piexels as a line segment rather than as individual points, which differs from previous works and leads to a new algorithm. Experimental results using both synthetic and actual images are also described.

This paper discusses a new design method for 2-D variable FIR digital filters, which is an extension of our previous work for 1-D case. The method uses a 3-D prototype FIR filter whose cross-sections correspond to the desired characteristics of 2-D variable FIR filters. A 2-D variable-angle FIR fan filter is given as a design example.

For system identification problems, such as noise and echo cancellation, FIR adaptive filters are mainly used for their simple adaptation and numerical stability. When the unknown system is a high-Q resonant system, having a very long impulse response, IIR adaptive filters are more efficient for reduction in the order of a transfer function. One way to realize the IIR adaptive filter is a separate form, in which the numerator and the denominator are separately realized and adjusted. In the actual applications, the order of the unknown system is not known. In this case, it is very important to estimate the total order and the order assignment on the numerator and the denominator. In this paper, effects of the order estimation error on the residual error are investigated. In this form, indirect error evaluation called "equation error" is used. Through theoretical and numerical investigation, the following results are obtained. First, under estimation of the order of the denominator causes large degradation. Second, over estimation can improve the performance. However, this improvement is saturated to some extent due to cancellation of the redundant poles and zeros. Third, the system identification error is proportional to the equation error as the adaptive filter approaching the optimum. Finally, there is possibility of recovering from the unstable state as the order assignment approaches to the optimum in an adaptive process using the equation error. Computer solutions are provided to aid in gaining insight of the order assignment and stability problem.

Kumar and Billinton have presented a new technique for obtaining the steady-state probabilities from a flow graph based on Markov model. By examining the graph and choosing suitable input and output nodes, the steady-state probabilities can be obtained directly by using the flow graph. In this paper this graphical technique is applied for a k-out-of-n: G repairable system. Consequently a new derivation way of the formulae for the steady-state availability and MTBF is obtained.

In this paper, a fault model for multiple-valued programmable logic arrays (MV-PLAs) is proposed and the equivalences of faults of MV-PLA's are discussed. In a supposed multiple-valued NOR/TSUM PLA model, it is shown that multiple-valued stuck-at faults, multiple-valued bridging faults, multiple-valued threshold shift faults and other some faults in a literal generator circuit are equivalent or subequivalent to a multiple crosspoint fault in the NOR plane or a multiple fault of weights in the TSUM plane. These results lead the fact that multiple-valued test vector set which indicates all multiple crosspoint fault and all multiple fault of weights also detects above equivalent or subequivalent faults in a MV-PLA.

The transistor action with negative differential resistance (NDR) of a nanometer-thick metal (CoSi2)/insulator (CaF2) resonant tunneling transistor is discussed for two transistor structures. These transistors are composed of metal-insulator (M-I) heterostructures with two metallic (CoSi2) quantum wells and three insulator (CaF2) barriers grown on an n-Si (lll) substrate. One of the two structures has the base terminal connected to one of the quantum wells next to the collector, and the other, to one next to the emitter. Although base resistance is high maybe due to the damage caused during the fabrication process, the two transistors show different characteristics, as expected theoretically. Transfer efficiency α (= IC/IE) close to unity was obtained at 77 K for electrons through the resonant levels in M-I heterostructures.

This paper proposes an adaptive modulation/TDMA scheme to achieve high capacity personal multi-media communication systems. TDMA is employed to cope with various bit rate for multi-media services. The modulation scheme is selected from 1/4-rate QPSK, 1/2-rate QPSK, QPSK, 16QAM and 64QAM according to the received C/IC (power ratio of the desired signal to the co-channel interference) and the delay spread. The spectral efficiency is evaluated by using the simulated bit error rate (BER) performance as well as the cumulative distribution of the C/IC with parameters of cell configurations. The results show that the spectral efficiency of the proposed scheme is 3.5 times higher than that of the conventional QPSK systems at the outage probability of 10%, and the effect is more remarkable at lower outage probability. The results also show that the proposed adaptive modulation is effective in improving delay spread immunity.

This paper presents the M-LCELP (Multi-mode Learned Code Excited LPC) speech coder, which has been developed for the next generation half-rate digital cellular telephone systems. M-LCELP develops the following techniques to achieve high-quality synthetic speech at 4kb/s with practically reasonable computation and memory requirements: (1) Multi-mode and multi-codebook coding to improve coding efficiency, (2) Pitch lag differential coding with pitch tracking to reduce lag transmission rate, (3) A two-stage joint design regular-pulse codebook with common phase structure in voiced frames, to drastically reduce computation and memory requirements, (4) An efficient vector quantization for LSP parameters, (5) An adaptive MA type comb filter to suppress excitation signal inter-harmonic noise. The MOS subjective test results demonstrate that 4.075kb/s M-LCELP synthetic speech quality is mostly equivalent to that for a North American full-rate standard VSELP coder. M-LCELP codec requires 18 MOPS computation amount. The codec has been implemented using 2 floating-point dsp chips.

Radar signals fluctuate because of the incoherent scattering of raindrops. Dual-polarization radar estimates rainfall rates from differential reflectivity (ZDR) and horizontal reflectivity (ZH). Here, ZDR and ZH are extracted from fluctuating radar signals by averaging. Therefore, instrumentally measured ZDR and ZH always have errors, so that estimated rainfall rates also have errors. This paper evaluates rainfall rate errors caused by signal fluctuation. Computer simulation based on a physical raindrop model is used to investigate the standard deviation of rainfall rate. The simulation considers acquisition time, and uses both simultaneous and alternate sampling of horizontal and vertical polarizations for square law and logarithmic estimators at various rainfall rates and elevation angles. When measuring rainfall rates that range from 1.0 to 10.0mm/h with the alternate sampling method, using a logarithmic estimator at a relatively large elevation angle, the estimated rainfall rates have significant errors. The simultaneous sampling method is effective in reducing these errors.

Development of a large-scale mobile communications network (IMN: Intelligent Mobile communications Network), as an infrastructure integrating multimedia functions, is indispensable for the support of future mobile communication services aiming toward "personalization," "intelligence," and "multimedia services." This paper discusses the aims of mobile communications and the outline of network technology aspects of PDC (Personal Digital Cellular) network which is currently in service. In addition, the future prospect of mobile communication technologies is discussed with special focuses on the support of universal mobility, network architecture including mobile communications platform, and multimedia technologies in the transport and access systems.

The stability of a terminated two-port network is investigated, and the stability conditions with only one inequality are obtained. Furthermore, the stability conditions with two inequalities, which are in the same form as those for the passive terminations known at the present time, are also obtained.

The static and dynamic characteristics of the lateral IGBT on the SOI film when the collector voltage of the IGBT is applied to the substrate are invesigated for its application to the high side switch. The measurements on the blocking capability and the switching characteristics under an inductive load are carried out with varying the thickness of the SOI film. The 260 V IGBT can be fabricated on the 5 µm thick SOI film without the special device structure. It is confirmed that the switching speed depends strongly on the SOI film thickness, not on the substrate bias. The dynamic latch-up current during the turn-off transient increases with the decrease in the SOI film thickness. This is caused by the large transient substrate current. This paper exhibits that applying the collector voltage of the IGBT to the substrate makes it possible to improve the characteristics of the IGBT on the thin SOI film.

We report the development of high-performance small-scale AlGaAs/GaAs collector-up heterojunction bipolar transistors (C-up HBT) with a carbon (C)-doped base layer. Oxygen-ion (O+) implantation is used to define their intrinsic emitter/base junctions and zinc (Zn)-diffusion is used to lower the resistivity of their O+-implanted extrinsic base layers. The highly resistive O+-implanted AlGaAs layer in the extrinsic emitter region sufficiently suppresses electron injection even under high-forward-bias conditions, allowing high collector current densities. The use of a C-doped base is especially effective for small-scale C-up HBT's because it suppresses the undesirable turn-on voltage shift caused by base dopant diffusion in the intrinsic area around the collector-mesa perimeter that occurs during the high-temperature Zn-diffusion process after implantation. Even in a small-scale trasistor with a 2 µm2 µm collector, a current gain of 15 is obtained. A microwave transistor with a 2 µm10 µm collector has a cutoff frequency fT of 68 GHz and a maximum oscillation frequency fmax of 102 GHz. A small-scale C-up HBT with a 2 µm2 µm collector shows a higher fmax of 110 GHz due to reduced base/collector capacitance CBC and its fmax remains above 100 GHz, even at a low collector current of 1 mA. The CBC of this device is estimated to be as low as 2.2 fF. Current gain dependence on collector size is also investigated for C-up HBT's and it is found that the base recombination current around the collector-mesa perimeter reduces the current gain.

This paper describes small AlGaAs/GaAs HBT's for low-power and high-speed integrated circuits. The device fabrication is based on a new bridged base electrode technology that permits emitter width to be defined down to 1 µm. The new technology features oxygen-ion implantation for emitter-base junction isolation and zinc diffusion for extrinsic base formation. The oxygen-ion implanted emitter-base junction edge has been shown to provide a periphery recombination current much lower than that for the previous proton implanted edgs, the result being a much higher current gain particularly in small devices. The zinc diffusion offers high device yield and good uniformity in device characteristics even for a very thin (0.04 µm) base structure. An HBT with emitter dimensions of 12.4 µm2 yields an fT of 103 GHz and an fmax of 62 GHz, demonstrating that the new technology has a significant advantage in reducing the parasitic elements of small devices. Fabricated one-by-eight static frequency dividers and one-by-four/one-by-five two-modulus prescalers operate at frequencies over 10 GHz. The emitters of HBT's used in the divider are 12.4 µm2 in size, which is the smallest ever reported for AlGaAs/GaAs HBT IC's. These results indicate that the bridged base electrode technology is promising for developing a variety of high-speed HBT IC's.

Three-dimensional display technologies that require special glasses are not suitable for telecommunications because wearing glasses is inconvenient and it is defficult to observe facial expressions. Our previous 6.3-inch 3D display was inadequate for presenting images with realistic sensation. In this paper, a direct view 15-inch 3D display is described. The display is made up of a l5-inch TFT LCD and a composite lenticular sheet (LS), and uses the head tracking technique. Quantitative evaluation of the stereoscopic sensation of the display was studied using the 3D display, and better stereoscopic sensation values were obtained compared with a 2D display mode, thus comfirming the display's usefulness.

A new steepest descent linear adaptive algorithm, called the proportion-sign algorithm (PSA), is introduced and its performance analysis is presented when the signals are from zero-mean jointly stationary Gaussian processes. The PSA improves the convergence speed over the least mean square (LMS) algorithm without overly degrading the steady-state error performance and has the robustness to impulsive interference occurring in the desired response by adding a minimal amount of computational complexity. Computer simulations are presented that show these advantages of the PSA over the LMS algorithm and demonstrate a close match between theoretical and empirical results to verify our analysis.