Over the past two decades, irregular low-density parity-check (LDPC) codes have not been able to decode information corrupted by insertion and deletion (ID) errors without markers. In this paper, we bring to light the existence of irregular LDPC codes that approach the symmetric information rates (SIR) of the channel with ID errors, even without markers. These codes have peculiar shapes in their check-node degree distributions. Specifically, the check-node degrees are scattered and there are degree-2 check nodes. We propose a code construction method based on the progressive edge-growth algorithm tailored for the scattered check-node degree distributions, which enables the SIR-approaching codes to progress in the finite-length regime. Moreover, the SIR-approaching codes demonstrate asymptotic and finite-length performance that outperform the existing counterparts, namely, concatenated coding of irregular LDPC codes with markers and spatially coupled LDPC codes.

Hum noise such as power line interference is one of the critical problems in the biomedical signal acquisition. Various techniques have been proposed to suppress power line interference. However, some of the techniques require more components and power consumption. The notch depth in the conventional N-path notch filter circuits needs a higher number of paths and switches off-resistance. It makes the conventional N-path notch filter less of efficiency to suppress hum noise. This work proposed the new N-path notch filter to hum noise suppression in biomedical signal acquisition. The new N-path notch filter achieved notch depth above 40dB with sampling frequency 50Hz and 60Hz. Although the proposed circuits use less number of path and switches off-resistance. The proposed circuit has been verified using artificial ECG signal contaminated by hum noise at frequency 50Hz and 60Hz. The output of N-path notch filter achieved a noise-free signal even if the sampling frequency changes.

Intersymbol interference (ISI) is a significant source of degradation in many digital communication systems including our proposed non-far region communication system using large array antennas in the millimeter-wave band in which the main cause of ISI can be attributed to the path delay differences among the elements of an array antenna. This paper proposes a quantitative method to evaluate the ISI estimated from the measured near-field distribution of the array antenna. The influence of the uniformity in the aperture field distribution in ISI is discussed and compared with an ideally uniform excitation. The reliability of the proposed method is verified through a comparison with another method based on direct measurements of the transmission between the actual antennas. Finally, the signal to noise plus interference is evaluated based on the estimated ISI results and ISI is shown to be the dominant cause of the degradation in the reception zone of the system.

In this paper, we propose a radio frequency (RF) anti-aliasing filter design method considering the effect of a roll-off characteristic on a noise figure (NF) in the direct RF undersampling receiver. The proposed method is useful for broadband reception that a system bandwidth (BW) has nearly half of the sampling frequency (1/2 fs). When the system BW is extended nearly 1/2 fs, the roll-off band is out of the desired Nyquist zone and it affects NF additionally. The proposed method offers a design target regarding the roll-off characteristic not only the rejection ratio. The target is helpful as a design guide to meet the allowed NF. We design the filter based on the proposed method and it is applied to the direct RF undersampling on-board receiver for Ka-band high throughput satellite (HTS). The measured NF value of the implemented receiver almost matched the designed value. Moreover, the receiver achieved the reception bandwidth which is 90% of 1/2 fs.

This paper describes designing a new pedestrian navigation system using a comprehensive framework called the pedestrian navigation concept reference model (PNCRM). We implement this system as a publicly-available smartphone application and evaluate its positioning performance near Omiya station's western entrance. We also evaluate users' subjective impressions of the system using a questionnaire. In both cases, promising results are obtained, showing that the PNCRM can be used as a tool for designing pedestrian navigation systems, allowing such systems to be created systematically.

Approximate multiplier design is an effective technique to improve hardware performance at the cost of accuracy loss. The current approximate multipliers are mostly ASIC-based and are dedicated for one particular application. In contrast, FPGA has been an attractive choice for many applications because of its high performance, reconfigurability, and fast development round. This paper presents a novel methodology for designing approximate multipliers by employing the FPGA-based fabrics (primarily look-up tables and carry chains). The area and latency are significantly reduced by applying approximation on carry results and cutting the carry propagation path in the multiplier. Moreover, we explore higher-order multipliers on architectural space by using our proposed small-size approximate multipliers as elementary modules. For different accuracy-hardware requirements, eight configurations for approximate 8×8 multiplier are discussed. In terms of mean relative error distance (MRED), the error of the proposed 8×8 multiplier is as low as 1.06%. Compared with the exact multiplier, our proposed design can reduce area by 43.66% and power by 24.24%. The critical path latency reduction is up to 29.50%. The proposed multiplier design has a better accuracy-hardware tradeoff than other designs with comparable accuracy. Moreover, image sharpening processing is used to assess the efficiency of approximate multipliers on application.

Reference current used in sense amplifiers is a crucial factor in a single-end read manner for emerging memories. Dummy cell average read scheme uses multiple pairs of dummy cells inside the array to generate an accurate reference current for data sensing. The previous research adopts current mirror sense amplifier (CMSA) which is compatible with the dummy cell average read scheme. However, clamped bit-line sense amplifier (CBLSA) has higher sensing speed and lower power consumption compared with CMSA. Therefore, applying CBLSA to dummy cell average read scheme is expected to enhance the performance. This paper reveals that direct combination of CBLSA and dummy cell average read scheme leads to sense margin degradation. In order to solve this problem, a new array design is proposed to make CBLSA compatible with dummy cell average read scheme. Current mirror structure is employed to prevent CBLSA from being short-circuited directly. The simulation result shows that the minimum sensible tunnel magnetoresistance ratio (TMRR) can be extended from 14.3% down to 1%. The access speed of the proposed sensing scheme is less than 2 ns when TMRR is 70% or larger, which is about twice higher than the previous research. And this circuit design just consumes half of the energy in one read cycle compared with the previous research. In the proposed array architecture, all the dummy cells can be always short-circuited in totally isolated area by low-resistance metal wiring instead of using controlling transistors. This structure is able to contribute to increasing the dummy cell averaging effect. Besides, the array-level simulation validates that the array design is accessible to every data cell. This design is generally applicable to any kinds of resistance-variable emerging memories including STT-MRAM.

We simulate some scenarios that 2/3 LEO satellites enhance 3/4/5 GPS satellites, to assess LEO-augmented GPS RTK positioning in signal-degraded environment. The effects of LEO-augmented GPS RTK in terms of reliability, availability and accuracy are presented, and the DIA algorithm is applied to deal with the poor data quality.

Embedding efficiency is an important issue in steganography methods. Matrix embedding (1, n, h) steganography was proposed by Crandall to achieve high embedding efficiency for palette images. This paper proposes a steganography method based on multilayer matrix embedding for palette images. First, a parity assignment is provided to increase the image quality. Then, a multilayer matrix embedding (k, 1, n, h) is presented to achieve high embedding efficiency and capacity. Without modifying the color palette, hk secret bits can be embedded into n pixels by changing at most k pixels. Under the same capacity, the embedding efficiency of the proposed method is compared with that of pixel-based steganography methods. The comparison indicates that the proposed method has higher embedding efficiency than pixel-based steganography methods. The experimental results also suggest that the proposed method provides higher image quality than some existing methods under the same embedding efficiency and capacity.

Cybersecurity has become a serious concern in our daily lives. The malicious functions inserted into hardware devices have been well known as hardware Trojans. In this letter, we propose a hardware-Trojan classification method at gate-level netlists utilizing boundary net structures. We first use a machine-learning-based hardware-Trojan detection method and classify the nets in a given netlist into a set of normal nets and a set of Trojan nets. Based on the classification results, we investigate the net structures around the boundary between normal nets and Trojan nets, and extract the features of the nets mistakenly identified to be normal nets or Trojan nets. Finally, based on the extracted features of the boundary nets, we again classify the nets in a given netlist into a set of normal nets and a set of Trojan nets. The experimental results demonstrate that our proposed method outperforms an existing machine-learning-based hardware-Trojan detection method in terms of its true positive rate.

The spectral efficiency of photonic networks can be enhanced by the use of higher modulation orders and narrower channel bandwidth. Unfortunately, these solutions are precluded by the margins required to offset uncertainties in system performance. Furthermore, as recently highlighted, the disaggregation of optical transport systems increases the required margin. We propose here highly spectrally efficient networks, whose margins are minimized by transmission-quality-aware adaptive modulation-order/channel-bandwidth assignment enabled by optical performance monitoring (OPM). Their effectiveness is confirmed by experiments on 400-Gbps dual-polarization quadrature phase shift keying (DP-QPSK) and 16-ary quadrature amplitude modulation (DP-16QAM) signals with the application of recently developed Q-factor-based OPM. Four-subcarrier 32-Gbaud DP-QPSK signals within 150/162.5/175GHz and two-subcarrier 32-Gbaud DP-16QAM signals within 75/87.5/100GHz are experimentally analyzed. Numerical network simulations in conjunction with the experimental results demonstrate that the proposed scheme can drastically improve network spectral efficiency.

A laser imaging detection and ranging (LIDAR) is one of the key sensors for autonomous driving. In order to improve its performance of the measurable distance, especially toward the front-side direction of the vehicle, this paper presents rapid revolution speed control of a brushless DC (BLDC) motor with a cyclostationary command signal. This enables the increase of the signal integration time for the designated direction, and thus improves the signal-to-noise ratio (SNR), while maintaining the averaged revolution speed. We propose the use of pre-emphasis circuits to accelerate and decelerate the revolution speed of the motor rapidly, by modifying the command signal so as to enhance the transition of the speed. The adaptive signal processing can adjust coefficients of the pre-emphasis filter automatically, so that it can compensate for the decayed response of the motor and its controller. Experiments with a 20-W BLDC motor prove that the proposed technique can achieve the actual revolution speed output to track the designated speed profile ranging from 600 to 1400 revolutions per minute (rpm) during one turn.

This paper proposes a sampling strategy for bandlimited graph signals over perturbed graph, in which we assume the edge between any pair of the nodes may be deleted randomly. Considering the mismatch between the true graph and the presumed graph, we derive the mean square error (MSE) of the reconstructed bandlimited graph signals. To minimize the MSE, we propose a greedy-based algorithm to obtain the optimal sampling set. Furthermore, we use Neumann series to avoid the pseudo-inverse computing. An efficient algorithm with low-complexity is thus proposed. Finally, numerical results show the superiority of our proposed algorithms over the other existing algorithms.

We analyze the cost of networks consisting of optical cross-connect nodes with different architectures for realizing the next generation large bandwidth networks. The node architectures include wavelength granular and fiber granular optical routing cross-connects. The network cost, capital expenditure (CapEx), involves link cost and node cost, both of which are evaluated for different scale networks under various traffic volumes. Numerical experiments demonstrate that the subsystem modular architecture with wavelength granular routing yields the highest cost effectiveness over a wide range of parameter values.

Rapid development of modern communications has initiated essential requirements for providing efficient algorithms that can solve the routing and wavelength assignment (RWA) problem in satellite optical networks. In this paper, the bee colony algorithm optimization based on link cost for RWA (BCO-LCRWA) is tailored for satellite networks composed of intersatellite laser links. In BCO-LCRWA, a cost model of intersatellite laser links is established based on metrics of network transmission performance namely delay and wavelengths utilization, with constraints of Doppler wavelength drift, transmission delay, wavelength consistency and continuity. Specifically, the fitness function of bee colony exploited in the proposed algorithm takes wavelength resources utilization and communication hops into account to implement effective utilization of wavelengths, to avoid unnecessary over-detouring and ensure bit error rate (BER) performance of the system. The simulation results corroborate the improved performance of the proposed algorithm compared with the existing alternatives.

Linear feed-forward/feedback shift registers are used as an effective tool of testing circuits in various fields including built-in self-test and secure scan design. In this paper, we consider the issue of testing linear feed-forward/feedback shift registers themselves. To test linear feed-forward/feedback shift registers, it is necessary to generate a test sequence for each register. We first present an experimental result such that a commercial ATPG (automatic test pattern generator) cannot always generate a test sequence with high fault coverage even for 64-stage linear feed-forward/feedback shift registers. We then show that there exists a universal test sequence with 100% of fault coverage for the class of linear feed-forward/feedback shift registers so that no test generation is required, i.e., the cost of test generation is zero. We prove the existence theorem of universal test sequences for the class of linear feed-forward/feedback shift registers.

The modern radar signals are in a wide frequency space. The receiving bandwidth of the radar reconnaissance receiver should be wide enough to intercept the modern radar signals. The Nyquist folding receiver (NYFR) is a novel wideband receiving architecture and it has a high intercept probability. Chirp signals are widely used in modern radar system. Because of the wideband receiving ability, the NYFR will receive the concurrent multiple chirp signals. In this letter, we propose a novel parameter estimation algorithm for the multiple chirp signals intercepted by single channel NYFR. Compared with the composite NYFR, the proposed method can save receiving resources. In addition, the proposed approach can estimate the parameters of the chirp signals even the NYFR outputs are under frequency aliasing circumstance. Simulation results show the efficacy of the proposed method.

Here, we present a novel spectroscopic imaging method based on the boundary-extraction scheme for wide-beam terahertz (THz) three-dimensional imaging. Optical-lens-focusing systems for THz subsurface imaging generally require the depth of the object from the surface to be input beforehand to achieve the desired azimuth resolution. This limitation can be alleviated by incorporating a wide-beam THz transmitter into the synthetic aperture to automatically change the focusing depth in the post-signal processing. The range point migration (RPM) method has been demonstrated to have significant advantages in terms of imaging accuracy over the synthetic-aperture method. Moreover, in the RPM scheme, spectroscopic information can be easily associated with each scattering center. Thus, we propose an RPM-based terahertz spectroscopic imaging method. The finite-difference time-domain-based numerical analysis shows that the proposed algorithm provides accurate target boundary imaging associated with each frequency-dependent characteristic.

We propose an auxiliary-noise power-scheduling method for a pre-inverse active noise control (PIANC) system. Conventional methods cannot reduce the power of auxiliary-noise due to the use of the filtered-x least mean square (FxLMS) algorithm. We developed our power-scheduling method for a PIANC system to solve this problem. Since a PIANC system uses a delayed input signal for a control filter, the proposed method delivers stability even if the acoustic path fluctuates. The proposed method also controls the gain of the auxiliary-noise based on the secondary-path-modeling state. The proposed method determines this state by the variation in the power of the secondary-path-modeling-error signal. Thus, the proposed method changes the power-scheduling of the auxiliary-noise. When the adaptive algorithm does not sufficiently converge, the proposed method injects auxiliary-noise. However, auxiliary-noise stops when the adaptive algorithm sufficiently converges. Therefore, the proposed method improves noise reduction performance.

In this paper, we propose an effective and robust method of spatial feature extraction for acoustic scene analysis utilizing partially synchronized and/or closely located distributed microphones. In the proposed method, a new cepstrum feature utilizing a graph-based basis transformation to extract spatial information from distributed microphones, while taking into account whether any pairs of microphones are synchronized and/or closely located, is introduced. Specifically, in the proposed graph-based cepstrum, the log-amplitude of a multichannel observation is converted to a feature vector utilizing the inverse graph Fourier transform, which is a method of basis transformation of a signal on a graph. Results of experiments using real environmental sounds show that the proposed graph-based cepstrum robustly extracts spatial information with consideration of the microphone connections. Moreover, the results indicate that the proposed method more robustly classifies acoustic scenes than conventional spatial features when the observed sounds have a large synchronization mismatch between partially synchronized microphone groups.