A forward/reverse body bias generator (BBG) which operates under wide supply-range is proposed. Fine-grained body biasing (FGBB) is effective to reduce variability and increase energy efficiency on digital LSIs. Since FGBB requires a number of BBGs to be implemented, simple design is preferred. We propose a BBG with charge pumps for reverse body bias and the BBG operates under wide supply-range from 0.5,V to 1.2,V. Layout of the BBG was designed in a cell-based flow with an AES core and fabricated in a 65~nm CMOS process. Area of the AES core is 0.22 mm$^2$ and area overhead of the BBG is 2.3%. Demonstration of the AES core shows a successful operation with the supply voltage from 0.5,V to 1.2,V which enables the reduction of power dissipation, for example, of 17% at 400,MHz operation.

This paper proposes a pipeline analog-to-digital converter (ADC) with non-binary encoding technique based on β-expansion. By using multiply-by-β switched-capacitor (SC) multiplying digital-to-analog converter (MDAC) circuit, our proposed ADC is composed by radix-β (1 < β < 2) 1 bit pipeline stages instead of using the conventional radix-2 1.5 bit/1 bit pipeline stages to realize non-binary analog-to-digital conversion. Also with proposed β-value estimation algorithm, there is not any digital calibration technique is required in proposed pipeline ADC. The redundancy of non-binary ADC tolerates not only the non-ideality of comparator, but also the mismatch of capacitances and the gain error of operational amplifier (op-amp) in MDAC. As a result, the power hungry high gain and wide bandwidth op-amps are not necessary for high resolution ADC, so that the reliability-enhanced pipeline ADC with simple amplifiers can operate faster and with lower power. We analyse the β-expansion of AD conversion and modify the β-encoding technique for pipeline ADC. In our knowledge, this is the first proposal architecture for non-binary pipeline ADC. The reliability of the proposed ADC architecture and β-encoding technique are verified by MATLAB simulations.

A design methodology for implementation of low-noise switched-capacitor low-pass filter (SC LPF) with small capacitance spread is proposed. The proposed method is focused on the reduction of operational amplifier noise transfer gain at low frequencies and the reduction of total capacitance. A new SC LPF topology is proposed in order to adapt the correlated double sampling and charge scaling technique at the same time. Design examples show that proposed filter reduces the total capacitance by 65% or more compared to the conventional one without having significant increase in noise transfer gain.

A technique to reduce noise transfer functions (NTF) of switched-capacitor (SC) integrators without changing their signal transfer functions (STF) is proposed. The proposed technique based on a simple reconnection scheme of multiple sampling capacitors. It can be implemented into any SC integrators as long as they have a transfer delay. A design strategy is also given to reduce the effect of parasitic capacitors. An SC integrator with a small total capacitance and a low noise transfer gain based on the proposed technique is also proposed. For a given design example, the total capacitance and the simulated noise transfer gain of the proposed SC integrator are 37% and 90% less than the conventional one.

A fifth-order switched-capacitor (SC) complex filter was implemented in 0.2-µm CMOS technology. A novel SC integrator was developed to reduce the die size and current consumption of the filter. The filter is centered at 24.730.15 kHz (3δ) and has a bandwidth of 20.260.3 kHz (3δ). The image channel is attenuated by more than 42.6 dB. The in-band third-order harmonic input intercept point (IIP3) is 17.3 dBm, and the input referred RMS noise is 34.3 µVrms. The complex filter consumes 350 µA with a 2.0-V power supply. The die size is 0.578 mm2. Owing to the new SC integrator, the filter achieves a 27% reduction in die size without any degradation in its characteristics, including its noise performance, compared with the conventional equivalent.

This paper presents a novel time-domain design procedure for fast-settling three-stage nested-Miller compensated (NMC) amplifiers. In the proposed design methodology, the amplifier is designed to settle within a definite time period with a given settling accuracy by optimizing both the power consumption and silicon die area. Detailed design equations are presented and the circuit level simulation results are provided to verify the usefulness of the proposed design procedure with respect to the previously reported design schemes.

This paper presents an enhanced dual-path delta-sigma analog-to-digital converter. Compared with other architectures, the enhanced architecture increases the noise shaping order without any instability problems and displays analog complexity equivalent to the multi-stage noise shaping architecture. Our delta-sigma converter is based on this new architecture. It employs not only doubly-differential structure to reduce common-mode errors in the system-level but also delayed-feed-in structure to mitigate the timing constraint of the feedback signal. Regarding the circuit implementation, the first-order enhancement of the quantization noise shaping is achieved via the use of a switched capacitor circuit technique. The circuit is incorporated into the active adder in a low-distortion structure. The supporting clock generation circuit that provides additional phases of clocks with the enhancement block is also implemented in the CMOS logic gates. A digital dynamic element matching circuit (i.e., segmented data-weighted-average circuit) is designed to reduce mismatch errors caused by the feedback DAC of modulator. A test chip, fabricated in a 0.18-µm CMOS process, provides a signal-to-noise+distortion ratio (SNDR) of 75-dB for a 1.0-MHz signal bandwidth clocked at 40-MHz. The 2nd harmonic is -101 dB and the 3rd harmonic is -94 dB when a -4.5-dB 100-kHz input signal is applied.

A multiple-input switched-capacitor DC-DC converter which can realize long battery runtime is proposed in this letter. Unlike conventional converters for a back-lighting application, the proposed converter drives some LEDs by converting energy from solar cells. Furthermore, the proposed converter can charge a lithium battery when an output load is light. The validity of circuit design is confirmed by theoretical analyses, simulations, and experiments.

This paper presents the analysis of hybrid cascode compensation scheme, merged Ahuja and improved Ahuja style compensation methods, which is used in two-stage CMOS operational transconductance amplifiers (OTAs). The open loop signal transfer function is derived to allow the accurate estimation of the poles and zeros. This analytical approach shows that the non-dominant poles and zeros of the hybrid cascode compensation are about 40 percent greater than those of the conventional cascode compensation. Circuit level simulation results are provided to show the accuracy of the calculated expressions and also the usefulness of the proposed cascode compensation technique.

In a switched-capacitor (SC) circuit, the major block is an operational transconductance amplifier (OTA) designed in order to form a feedback loop. However, the OTA is the block that consumes most of the power in SC circuits. This paper proposes the use of a class-C inverter instead of the OTA in SC circuits and a corresponding switches configuration for extremely low power applications. A detailed analysis and design trade-offs are also provided. Simulation and experimental results show that sufficient performance can be obtained even though a class-C inverter is used. The second-order biquad filter and the second-order SC sigma-delta (ΣΔ) modulator based on a class-C inverter are designed. These circuits have been fabricated with a 0.35-µm CMOS process. The measurement results of the fabricated SC biquad filter show a 59-dB signal-to-noise-plus-distortion ratio (SNDR) for a 0.2-Vp-p input signal and 0.9-V dynamic ranges. The power consumption of the biquad filter is only 0.4 µW with a 1-V power supply. The measurement results of the fabricated ΣΔ modulator show a 61-dB peak SNR for a 1.6-kHz bandwidth with a sample rate of 200 kHz. The modulator consumes 0.8 µW with a 1-V power supply.

This paper presents a novel class of sigma-delta modulator topologies for low-voltage, high-speed, and high-resolution applications with low oversampling ratios (OSRs). The main specifications of these architectures are the reduced analog circuit requirements, large out-of-band gain in the noise transfer function (NTF) without any stability concerns to achieve high signal to noise ratio (SNR) with a low OSR, and unity-gain signal transfer function (STF) to reduce the harmonic distortions resulted from the analog circuit imperfections. To demonstrate the efficiency of the proposed modulator architectures a prototype with HSPICE is implemented. A low-power two-stage class A/AB OTA with modified common mode feedback (CMFB) circuit in the first stage is used to implement the fourth order modulator. Simulation results with OSR of 16 give signal to noise plus distortion ratio (SNDR) and dynamic range (DR) of 90-dB and 92.5-dB including the circuit noise in the 1.25-MHz signal bandwidth, respectively. The circuit is implemented in a 0.13-µm standard CMOS technology. It dissipates about 40-mW from a single 1.2-V power supply voltage.

A high-speed high-resolution sample-and-hold amplifier (SHA) is designed for time-interleaved analog-to-digital converter applications. Using the techniques of precharging and output capacitor coupling can mitigate the stringent performance requirements for the opamp, resulting in low power dissipation. Implemented in a standard 0.25 µm CMOS technology, the SHA achieves 80 dB spurious-free dynamic range (SFDR) for a 1.8 Vpp output at 100 MHz Nyquist sampling rate. The SHA occupies a die area of 0.35 mm2 and dissipates 33 mW from a single 2.5 V supply.

A new analog correlator circuit is proposed for direct sequence code division multiple access (DS-CDMA) demodulator. The circuit consists of only 16 switches, 4 capacitors and 2 level shifters. Control sequence requires only three clock phases. Simulation with code length of 127 reveals that the proposed circuit has a good ability to cancel off the charge error and dissipates 3.4mW at 128MHz. The circuit had been designed using a 0.6µm CMOS process. The area of 256µm 245µm is estimated to be 9 times smaller compared to other reported equivalent analog correlators.

The delta-sigma modulator (DSM) is an excellent choice for high-resolution analog-to-digital converters. Recently, a band-pass DSM has been a desirable choice for direct conversion of an IF signal into a digital bit stream. This paper proposes a quadrature band-pass DSM for digitizing a narrow-band IF signal. This modulator can achieve a lower total order, higher signal-to-noise ratio (SNR), and higher bandwidth when compared with conventional band-pass modulators. An experimental prototype employing the quadrature topology has been integrated in 0.6 µm, double-poly, double-metal CMOS technology with capacitors synthesized from a stacked poly structure. This system clocked at 13 MHz and digitized a 200 kHz bandwidth signal centered at 4.875 MHz with 100 dB of dynamic range. Power consumption is 190 mW at 5 V.

A 24-bit, 96 kHz stereo A/D converter (ADC) for DVD-audio has been developed. The single-chip integrates stereo delta-sigma modulators (Δ ΣM's), a voltage reference, and a decimation filter. A fourth-order cascaded Δ ΣM using a local feedback technique was employed to avoid overload without sacrificing noise performance. Low power switched-capacitor techniques were used for implementation. A two-stage decimation filter architecture that reduces digital switching noise was also developed. A merged multi-stage comb filter was used for the first stage, and a bit-serial finite-impulse-response (FIR) filter was used for the second stage. The 18.0 mm2 chip was fabricated in 0.6-µm CMOS with low threshold devices. Measured results show 117 dB A-weighted dynamic range in the 20 kHz passband, with 470 mW power dissipation at 5 V operation.

To improve measurement accuracy and speed, a switched-capacitor capacitance measurement circuit with the vernier scale is developed. Its process consists of a coarse measurement by charge-balancing A-D conversion and a fine measurement by single-slope A-D conversion. a prototype using discrete components confirms the principles of operation.

A cyclic analog-to-digital (A/D) converter is developed which accomplishes an n-b conversion in n/2 clock cycles. The architecture consists of two 1-b quantizers connected in a loop. A CMOS design of the 1-b quantizer is given to evaluate the performance of the A/D converter when implemented using presently available process. Spice simulations and error analyses show that a resolution higher than 10-b and a sampling rate up to 1.4 Msps are attainable with a 3-µm CMOS process. A prototype converter breadboarded using discrete components has confirmed the principles of operation and error analyses. The device count and the power consumption are small compared to those of a successive-approximation A/D converter. A chip area required for the CMOS implementation is also small because only four unit capacitors are involved. Therefore, the architecture proposed herein is most suited for high accuracy, medium speed A/D conversion.