This paper proposes a scan design for delay fault testability of dual circuits. In normal operation mode, each proposed scan flip flop operates as a master-slave flip flop. In test mode, the proposed scan design performs scan operation using two scan paths, namely master scan path and slave scan path. The master scan path consists of master latches and the slave scan path consists of slave latches. In the proposed scan design, arbitrary two-patterns can be set to flip flops of dual circuits. Therefore, it achieves complete fault coverage for robust and non-robust testable delay fault testing. It requires no extra latch unlike enhanced scan design. Thus the area overhead is low. The evaluation shows the test application time of the proposed scan design is 58.0% of that of the enhanced scan design, and the area overhead of the proposed scan design is 13.0% lower than that of the enhanced scan design. In addition, in testing of single circuits, it achieves complete fault coverage of robust and non-robust testable delay fault testing. It requires smaller test data volume than the enhanced scan design in testing of single circuits.

Multi-context FPGAs allow very quick reconfiguration by storing multiple configuration data at the same time. While testing for FPGAs with single-context memories has already been studied by many researchers, testing for multi-context FPGAs has not been proposed yet. This paper presents an architecture of testable multi-context FPGAs. In the proposed multi-context FPGA, configuration data stored in a context can be copied into another context. This paper also shows testing of the proposed multi-context FPGA. The proposed testing uses the testing for the traditional FPGAs with single-context. The testing is capable of detecting single stuck-at faults and single open faults which affect normal operations. The number of test configurations for the proposed testing is at most two more than that for the testing of FPGAs with single-context memories. The area overhead of the proposed architecture is 7% and 4% of the area of a multi-context FPGA without the proposed architecture when the number of contexts in a configuration memory is 8 and 16, respectively.

This letter presents a code which corrects single bit errors in any location of the word as well as l-bit burst errors occurred in an important part of the word. The proposed code is designed by product of the parity check matrix of the l-bit burst error correcting codes and the matrix which converts input unequal errors into equal errors. This letter also demonstrates the evaluation of the code, and presents the extended codes with two-level burst error correcting capabilities by interleaving.

The recent development of semiconductor technology has led to downsized, large-scaled and low-power VLSI systems. However, the incidence of soft errors has increased. Soft errors are temporary events caused by striking of α-rays and high energy neutron radiation. Since the scale of VLSI has become smaller in recent development, it is necessary to consider the occurrence of not only single node upset (SNU) but also double node upset (DNU). The existing High-performance, Low-cost, and DNU Tolerant Latch design (HLDTL) does not completely tolerate DNU. This paper presents a new design of a DNU tolerant latch to resolve this issue by adding some transistors to the HLDTL latch.

To increase the yield of data processing circuits such as adders and logic operation circuits, the bit-slice reconfiguration design has been proposed as an efficient redundant technology for defect-tolerance. Wallace multipliers are a well-known class of high-speed parallel multipliers. Unfortunately, the bit-slice reconfiguration design is not applicable to Wallace multipliers because Wallace multipliers do not have regular bit-slice structure. Therefore, redundant designs for Wallace multipliers have been regarded impossible. This paper proposes a redundant design for Wallace multipliers. In order to design redundant Wallace multipliers, first, 2n heterogeneous slices are considered in a non-redundant nn Wallace multiplier. The proposed redundant Wallace multipliers contain reconfigurable slices which can play the role of both i-th and (i+1)-th slices. Since the i-th slice has a similar structure to the (i+1)-th slice, the reconfigurable slice is not much larger than the i-th slice. This paper also shows a repair procedure for the proposed design. This paper evaluates the proposed design from the viewpoint of the yield, area, effective yield and delay time. For example, the yield of a 3232 Wallace multiplier increases from 0.30 to 0.41 by applying the proposed design while the area increases by a factor of 1.21.

As technology scales to 45 nm and below, the reliability of VLSI declines due to small delay defects, which are hard to detect by functional clock frequency. To detect small delay defects, a method which measures the delay time of path in circuit under test (CUT) was proposed. However, because a large number of FFs exist in recent VLSI, the probability that the resistive defect occurs in the FFs is increased. A test method measuring path delay time including the transmission time of FFs is necessary. However, the path measured by the conventional on-chip path delay time measurement method does not include a part of a master latch. Thus, testing using the conventional measurement method cannot detect defects occurring on the part. This paper proposes an improved on-chip path delay time measurement method. Test coverage is improved by measuring the path delay time including transmission time of a master latch. The proposed method uses a duty-cycle-modified clock signal. Evaluation results show that, the proposed method improves test coverage 5.2511.28% with the same area overhead as the conventional method.

This paper presents a scan design for delay fault testability of 2-rail logic circuits. The flip flops used in the scan design are based on master-slave ones. The proposed scan design provides complete fault coverage in delay fault testing of 2-rail logic circuits. In two-pattern testing with the proposed scan design, initial vectors are set using the set-reset operation, and the scan-in operation for initial vectors is not required. Hence, the test application time is reduced to about half that of the enhanced scan design. Because the additional function is only the set-reset operation of the slave latch, the area overhead is small. The evaluation shows that the differences in the area overhead of the proposed scan design from those of the standard scan design and the enhanced scan design are 2.1 and -14.5 percent on average, respectively.

In the recent high-density and low-power VLSIs, the occurrence of soft errors has become a significant problem. Recently, soft errors frequently occur on not only memory system but also logic circuits. Based on this standpoint, some constructions of soft-error-tolerant FFs were proposed. A conventional FF consists of some master and slave latches and C-elements. In the FF, soft error pulses occurring on combinational parts of logic circuits are corrected as long as the width of the pulses is narrow, that is within a specified width. However, error pulses with wide width are neither detected nor corrected in the FF. This paper presents a construction of soft-error-tolerant FFs by modifying the conventional soft-error-tolerant FF. The proposed FFs have the capability to detect error pulses having wide width as well as the capability to correct those having narrow width. The proposed FFs are also capable of detecting hard errors. The evaluation shows the soft-error-tolerant capability, AC characteristics, area overhead and power consumption of the FFs.

Small delay defects can cause serious issues such as very short lifetime in the recent VLSI devices. Delay measurement is useful to detect small delay defects in manufacturing testing. This paper presents a design for delay measurement to detect small delay defects on global routing resources, such as double, hex and long lines, in a Xilinx Virtex 4 based FPGA. This paper also shows a measurement method using the proposed design. The proposed measurement method is based on an existing one for SoC using delay value measurement circuit (DVMC). The proposed measurement modifies the construction of configurable logic blocks (CLBs) and utilizes an on-chip DVMC newly added. The number of configurations required by the proposed measurement is 60, which is comparable to that required by stuck-at fault testing for global routing resources in FPGAs. The area overhead is low for general FPGAs, in which the area of routing resources is much larger than that of the other elements such as CLBs. The area of every modified CLB is 7% larger than an original CLB, and the area of the on-chip DVMC is 22% as large as that of an original CLB. For recent FPGAs, we can estimate that the area overhead is approximately 2% or less of the FPGAs.

This paper proposes a method providing efficient test compression. The proposed method is for robust testable path delay fault testing with scan design facilitating two-pattern testing. In the proposed method, test data are interleaved before test compression using statistical coding. This paper also presents test architecture for two-pattern testing using the proposed method. The proposed method is experimentally evaluated from several viewpoints such as compression rates, test application time and area overhead. For robust testable path delay fault testing on 11 out of 20 ISCAS89 benchmark circuits, the proposed method provides better compression rates than the existing methods such as Huffman coding, run-length coding, Golomb coding, frequency-directed run-length (FDR) coding and variable-length input Huffman coding (VIHC).

There are three well-known approaches to using scan design to apply two-pattern testing: broadside testing (functional justification), skewed-load testing and enhanced scan testing. The broadside and skewed-load testing use the standard scan design, and thus the area overheads are not high. However fault coverage is low. The enhanced scan testing uses the enhanced scan design. The design uses extra latches, and allows scan-in any two-pattern testing. While this method achieves high fault coverage, it causes high area overhead because of extra latches. This paper presents a new scan design where two-pattern testing with high fault coverage can be performed with area overhead as low as the standard scan design. The proposed scan-FFs are based on master-slave FFs. The input of each scan-FF is connected to the output of the master latch and not the slave latch of the previous FF. Every scan-FF maintains the output value during scan-shift operations.

The importance of redundant technologies for improving dependability and delay fault testability are growing. This paper presents properties of a class of redundant technologies, namely two-rail logic, and analyzes testability of path delay faults occurring on two-rail logic circuits. The paper reveals the following characteristics of two-rail logic circuits: While the number of paths in two-rail logic circuits is twice that in ordinary single-rail logic circuits, the number of robust testable path delay faults in two-rail logic circuits is twice or more that in the single-rail logic circuits. This suggests two-rail logic circuits are more testable than ordinary single-rail logic circuits. On two-rail logic circuits, there may be some robust testable path delay faults that are functional un-sensitizable for any input vectors consisting of codewords of two-rail codes, i.e. for any input vectors that can occur during fault-free operation. Even if such faults occur, the circuits are still strongly fault secure for unidirectional stuck-at faults as well as they work correctly.

With IC design entering the nanometer scale integration, the reliability of VLSI has declined due to small-delay defects, which are hard to detect by traditional delay fault testing. To detect small-delay defects, on-chip delay measurement, which measures the delay time of paths in the circuit under test (CUT), was proposed. However, our pre-simulation results show that when using on-chip delay measurement method to detect small-delay defects, test generation under the single-path sensitization is required. This constraint makes the fault coverage very low. To improve fault coverage, this paper introduces techniques which use segmented scan and test point insertion (TPI). Evaluation results indicate that we can get an acceptable fault coverage, by combining these techniques for launch off shift (LOS) testing under the single-path sensitization condition. Specifically, fault coverage is improved 27.02∼47.74% with 6.33∼12.35% of hardware overhead.

This letter reveals that an edge-triggered master-slave flip-flop (FF) using well-known soft error tolerant DICE (dual interlocked storage cell) is vulnerable to soft errors occurring around clock edge. This letter presents a design of a soft error tolerant FF based on the master-slave FF using DICE. The proposed design modifies the connection between the master and slave latches to make the FF not vulnerable to these errors. The hardware overhead is almost the same as that for the original edge-triggered FF using the DICE.

In delay fault BIST (Built-In-Self-Test), an adjacency test pattern generation scheme effectively generates robust test patterns. The traditional adjacency test pattern generation schemes use LFSR to generate first patterns, and thus they cannot generate test patterns for circuits with more than 30 inputs with high fault coverage in a practical amount of time. This paper proposes a deterministic delay fault BIST method using adjacency test pattern generation. The proposed scheme uses first patterns generated by a deterministic algorithm based on the analysis of independent partial circuits on the circuit under test. Experiments show that test patterns generated by the proposed method have both high fault coverage and short test length, resulting in a short test time.

In recent VLSIs, small-delay defects, which are hard to detect by traditional delay fault testing, can bring about serious issues such as short lifetime. To detect small-delay defects, on-chip delay measurement which measures the delay time of paths in the circuit under test (CUT) was proposed. However, this approach incurs high test cost because it uses scan design, which brings about long test application time due to scan shift operation. Our solution is a test application time reduction method for testing using the on-chip path delay measurement. The testing with on-chip path delay measurement does not require capture operations, unlike the conventional delay testing. Specifically, FFs keep the transition pattern of the test pattern pair sensitizing a path under measurement (PUM) (denoted as p) even after the measurement of p. The proposed method uses this characteristic. The proposed method reduces scan shift time and test data volume using test pattern merging. Evaluation results on ISCAS89 benchmark circuits indicate that the proposed method reduces the test application time by 6.89∼62.67% and test data volume by 46.39∼74.86%.

This letter introduces an innovation for the heterogeneous storage architecture of AI chips, specifically focusing on the integration of six transistors(6T) and eight transistors(8T) hybrid SRAM. Traditional approaches to reducing SRAM power consumption typically involve lowering the operating voltage, a method that often substantially diminishes the recognition rate of neural networks. However, the innovative design detailed in this letter amalgamates the strengths of both SRAM types. It operates at a voltage lower than conventional SRAM, thereby significantly reducing the power consumption in neural networks without compromising performance.

This paper presents a construction of a single-event-upset (SEU) tolerant reset-set (RS) flip-flop (FF). The proposed RS-FF consists of four identical parts which form an interlocking feedback loop just like DICE. The area and average power consumption of the proposed RS-FFs are 1.101.48 and 1.201.63 times smaller than those of the conventional SEU tolerant RS-FFs, respectively.

In this paper, a soft-error-tolerant BILBO (Built-In Logic Block Observer) FF (flip-flop) is presented. The proposed FF works as a soft-error-tolerant FF in system operations and as a BILBO FF in manufacturing testing. The construction of the proposed FF is based on that of an existing soft-error-tolerant FF, namely a BISER (Built-In Soft Error Resilience) FF. The proposed FF contains a reconfigurable C-element with XNOR calculation capability, which works as a C-element for soft-error-tolerance during system operations and as an XNOR gate employed in linear feedback shift registers (LFSRs) during manufacturing testing. The evaluation results shown in this paper indicate that the area of the proposed FF is 8.5% smaller than that of a simple combination of the existing BISER and BILBO FFs. In addition, the sum of CLK-Q delay and D-CLK setup times on system operations for the proposed FF is 19.7% shorter than that for the combination.