This paper addresses the problem of finding, evaluating, and selecting the best set of codewords for the 4b/10b line code, a dependable line code with forward error correction (FEC) designed for real-time communication. Based on the results of our scheme [1], we formulate codeword search as an instance of the maximum clique problem, and enumerate all candidate codeword sets via maximum clique enumeration as proposed by Eblen et al. [2]. We then measure each set in terms of resistance to bit errors caused by noise and present a canonical set of codewords for the 4b/10b line code. Additionally, we show that maximum clique enumeration is #P-hard.

Cross-project defect prediction (CPDP) is a feasible solution to build an accurate prediction model without enough historical data. Although existing methods for CPDP that use only labeled data to build the prediction model achieve great results, there are much room left to further improve on prediction performance. In this paper we propose a Semi-Supervised Discriminative Feature Learning (SSDFL) approach for CPDP. SSDFL first transfers knowledge of source and target data into the common space by using a fully-connected neural network to mine potential similarities of source and target data. Next, we reduce the differences of both marginal distributions and conditional distributions between mapped source and target data. We also introduce the discriminative feature learning to make full use of label information, which is that the instances from the same class are close to each other and the instances from different classes are distant from each other. Extensive experiments are conducted on 10 projects from AEEEM and NASA datasets, and the experimental results indicate that our approach obtains better prediction performance than baselines.

In this paper, we propose a user-assisted QoS control scheme that utilizes media adaptive buffering to enhance QoE of audiovisual and haptic IP communications. The scheme consists of two modes: a manual mode and an automatic mode. It enables users to switch between these two modes according to their inclinations. We compare four QoS control schemes: the manual mode only, the automatic mode only, the switching scheme starting with the manual mode, and the switching scheme starting with the automatic mode. We assess the effects of the four schemes, user attributes, and tasks on QoE through a subjective experiment which provides information on users' behavior in addition to QoE scores. As a result of the experiment, we show that the user-assisted QoS control scheme can enhance QoE. Furthermore, we notice that the proper QoS control scheme depends on user attributes and tasks.

Over the past two decades, irregular low-density parity-check (LDPC) codes have not been able to decode information corrupted by insertion and deletion (ID) errors without markers. In this paper, we bring to light the existence of irregular LDPC codes that approach the symmetric information rates (SIR) of the channel with ID errors, even without markers. These codes have peculiar shapes in their check-node degree distributions. Specifically, the check-node degrees are scattered and there are degree-2 check nodes. We propose a code construction method based on the progressive edge-growth algorithm tailored for the scattered check-node degree distributions, which enables the SIR-approaching codes to progress in the finite-length regime. Moreover, the SIR-approaching codes demonstrate asymptotic and finite-length performance that outperform the existing counterparts, namely, concatenated coding of irregular LDPC codes with markers and spatially coupled LDPC codes.

In this paper, we propose a decentralized probabilistic frequency-block activation control method for the cellular downlink. The aim of the proposed method is to increase the downlink system throughput within the system coverage by adaptively controlling the individual activation of each frequency block at all base stations (BSs) to achieve inter-cell interference coordination (ICIC) and traffic load balancing. The proposed method does not rely on complicated inter-BS cooperation. It uses only the inter-BS information exchange regarding the observed system throughput levels with the neighboring BSs. Based on the shared temporal system throughput information, each BS independently controls online the activation of their respective frequency blocks in a probabilistic manner, which autonomously achieves ICIC and load balancing among BSs. Simulation results show that the proposed method achieves greater system throughput and a faster convergence rate than the conventional online probabilistic activation/deactivation control method. We also show that the proposed method successfully tracks dynamic changes in the user distribution generated due to mobility.

We aim at HDR imaging with simple processing while preventing spatial resolution degradation in multiple-exposure-time image sensor where the exposure time is controlled for each pixel. The contributions are the proposal of image interpolation by motion area detection and pixel adaptive weighting method by overexposure and motion blur detection.

Recently, intelligent heating, next generation microwave ovens that achieve uniform heating and spot heating using solid-state devices, has been actively studied. There are two types of microwave generators using solid-state devices. Since compactness is indispensable to accommodate in a limited space, the miniaturized oscillator type was selected. The authors proposed an imbalanced coupling resonator, a resonator-less feedback circuit, a high power frequency variable resonator, and injection-locked phase control in order to achieve high performance of the oscillator type microwave generator. In addition, we confirmed that the oscillator type can be used as the microwave generator for intelligent heating using a Wilkinson combiner. As a result, it was demonstrated that the oscillator type microwave generator, realized the same high efficiency (67%) as the amplifier type, and found the possibility of variable frequency (2.4 to 2.5GHz) and variable phase, and can be used as the microwave generator for intelligent heating.

With increasing technology scaling and the use of lower voltages, more research interest is being shown in variability-tolerant analog front end design. In this paper, we describe an adaptive amplitude control transmitter that is operated using differential signaling to reduce the temperature variability effect. It enables low power, low voltage operation by synergy between adaptive amplitude control and Vth temperature variation control. It is suitable for high-speed interface applications, particularly cable interfaces. By installing an aggressor circuit to estimate transmitter jitter and changing its frequency and activation rate, we were able to analyze the effects of the interface block on the input buffer and thence on the entire system. We also report a detailed estimation of the receiver clock-data recovery (CDR) operation for transmitter jitter estimation. These investigations provide suggestions for widening the eye opening of the transmitter.

The task of image annotation is becoming enormously important for efficient image retrieval from the web and other large databases. However, huge semantic information and complex dependency of labels on an image make the task challenging. Hence determining the semantic similarity between multiple labels on an image is useful to understand any incomplete label assignment for image retrieval. This work proposes a novel method to solve the problem of multi-label image annotation by unifying two different types of Laplacian regularization terms in deep convolutional neural network (CNN) for robust annotation performance. The unified Laplacian regularization model is implemented to address the missing labels efficiently by generating the contextual similarity between labels both internally and externally through their semantic similarities, which is the main contribution of this study. Specifically, we generate similarity matrices between labels internally by using Hayashi's quantification method-type III and externally by using the word2vec method. The generated similarity matrices from the two different methods are then combined as a Laplacian regularization term, which is used as the new objective function of the deep CNN. The Regularization term implemented in this study is able to address the multi-label annotation problem, enabling a more effectively trained neural network. Experimental results on public benchmark datasets reveal that the proposed unified regularization model with deep CNN produces significantly better results than the baseline CNN without regularization and other state-of-the-art methods for predicting missing labels.

To tackle the distributed power optimization problems in wireless sensor networks localization systems, we model the problem as a hierarchical game, i.e. a multi-leader multi-follower Stackelberg game. Existing researches focus on the power allocation of anchor nodes for ranging signals or the power management of agent nodes for cooperative localization, individually. However, the power optimizations for different nodes are indiscerptible due to the common objective of localization accuracy. So it is a new challenging task when the power allocation strategies are considered for anchor and agent nodes simultaneously. To cope with this problem, a hierarchical game is proposed where anchor nodes are modeled as leaders and agent nodes are modeled as followers. Then, we prove that games of leaders and followers are both potential games, which guarantees the Nash equilibrium (NE) of each game. Moreover, the existence of Stackelberg equilibrium (SE) is proved and achieved by the best response dynamics. Simulation results demonstrate that the proposed algorithm can have better localization accuracy compared with the decomposed algorithm and uniform strategy.

This paper presents a weighted spatial filter (WSF) design method based on direction of arrival (DOA) estimates for a novel array configuration called a sum and difference composite co-array. A sum and difference composite co-array is basically a combination of sum and difference co-arrays. Our configuration can realize higher degrees of freedom (DOF) with the sum co-array part at a calculation cost lower than those of the other sparse arrays. To further enhance the robustness of our proposed sum and difference composite co-array we design an optimal beam pattern by WSF based on the information of estimated DOAs. Performance of the proposed system and the DOA estimation accuracy of close-impinging waves are evaluated through computer simulations.

This paper presents a design of CMOS transimpedance amplifier (TIA) and peaking inductor for high speed, low power and small area. To realize high density integration of optical I/O, area reduction is an important figure as well as bandwidth, power and so on. To determine design parameters of multi-stage inverter-type TIA (INV-TIA) with peaking inductors, we derive a simplified model of the bandwidth and the energy per bit. Multi-layered on-chip inductors are designed for area-effective inductive peaking. A 5-stage INV-TIA with 3 peaking inductors is fabricated in a 65-nm CMOS. By using multi-layered inductors, 0.02 mm2 area is achieved. Measurement results show 45 Gb/s operation with 49 dBΩ transimpedance gain and 4.4 mW power consumption. The TIA achieves 98 fJ/bit energy efficiency.

Many studies of deep neural networks have reported inference accelerators for improved energy efficiency. We propose methods for further improving energy efficiency while maintaining recognition accuracy, which were developed by the co-design of a filter-by-filter quantization scheme with variable bit precision and a hardware architecture that fully supports it. Filter-wise quantization reduces the average bit precision of weights, so execution times and energy consumption for inference are reduced in proportion to the total number of computations multiplied by the average bit precision of weights. The hardware utilization is also improved by a bit-parallel architecture suitable for granularly quantized bit precision of weights. We implement the proposed architecture on an FPGA and demonstrate that the execution cycles are reduced to 1/5.3 for ResNet-50 on ImageNet in comparison with a conventional method, while maintaining recognition accuracy.

In this paper, we present non-Markovian availability models for capturing the dynamics of system behavior of an operational software system that undergoes aperiodic time-based software rejuvenation and checkpointing. Two availability models with rejuvenation are considered taking account of the procedure after the completion of rollback recovery operation. We further proceed to investigate whether there exists the optimal rejuvenation schedule that maximizes the steady-state system availability, which is derived by means of the phase expansion technique, since the resulting models are not the trivial stochastic models such as semi-Markov process and Markov regenerative process, so that it is hard to solve them by using the common approaches like Laplace-Stieltjes transform and embedded Markov chain techniques. The numerical experiments are conducted to determine the optimal rejuvenation trigger timing maximizing the steady-state system availability for each availability model, and to compare both two models.

For automotive millimeter radar, a method using a multi-input multi-output (MIMO) array antenna is essential for high angle resolution with module miniaturization. MIMO enables us to extend an antenna array with virtual antennas, and a large antenna array aperture enables high resolution angle estimation. Time division multiplex (TDM) MIMO, which is a method to generate virtual array antennas, makes it easy to design radar system integrated circuits. However, this method leads to two issues in signal processing; the phase error reduces the accuracy of angle estimation of a moving target, and the maximum detectable velocity decreases in inverse proportion to the number of Tx antennas. We analytically derived this phase error and proposed a method to correct the error. Because the phase error of TDM-MIMO is proportional to the target velocity, accurate estimation of the target velocity is an important issue for phase error correction. However, the decrease of the maximum detectable velocity in TDM-MIMO reduces the accuracy of both velocity estimation and angle estimation. To solve these issues, we propose new signal processing for range-velocity estimation for TDM-MIMO radar. By using the feedback result of the estimated direction of arrival (DoA), we can avoid decreasing the maximum detectable velocity. We explain our method with our simulation results.

Optical navigation (OPNAV) is the use of the on-board imaging data to provide a direct measurement of the image coordinates of the target as navigation information. Among the optical observables in deep-space, the edge of the celestial body is an important feature that can be utilized for locating the planet centroid. However, traditional edge detection algorithms like Canny algorithm cannot be applied directly for OPNAV due to the noise edges caused by surface markings. Moreover, due to the constrained computation and energy capacity on-board, light-weight image-processing algorithms with less computational complexity are desirable for real-time processing. Thus, to fast and accurately extract the edge of the celestial body from high-resolution satellite imageries, this paper presents an algorithm-hardware co-design of real-time edge detection for OPNAV. First, a light-weight edge detection algorithm is proposed to efficiently detect the edge of the celestial body while suppressing the noise edges caused by surface markings. Then, we further present an FPGA implementation of the proposed algorithm with an optimized real-time performance and resource efficiency. Experimental results show that, compared with the traditional edge detection algorithms, our proposed one enables more accurate celestial body edge detection, while simplifying the hardware implementation.

In this paper, we present a joint multi-patch and multi-task convolutional neural networks (JMM-CNNs) framework to learn more descriptive and robust face representation for face recognition. In the proposed JMM-CNNs, a set of multi-patch CNNs and a feature fusion network are constructed to learn and fuse global and local facial features, then a multi-task learning algorithm, including face recognition task and pose estimation task, is operated on the fused feature to obtain a pose-invariant face representation for the face recognition task. To further enhance the pose insensitiveness of the learned face representation, we also introduce a similarity regularization term on features of the two tasks to propose a regularization loss. Moreover, a simple but effective patch sampling strategy is applied to make the JMM-CNNs have an end-to-end network architecture. Experiments on Multi-PIE dataset demonstrate the effectiveness of the proposed method, and we achieve a competitive performance compared with state-of-the-art methods on Labeled Face in the Wild (LFW), YouTube Faces (YTF) and MegaFace Challenge.

This paper presents analysis results of the intermodulation distortion (IMD) components compensation conditions for dual-band feed-forward power amplifier (FFPA) when inputting dual-band signals simultaneously. The signal cancellation loop and distortion cancellation loop of the dual-band FFPA have frequency selective adjustment paths which consist of filter and vector regulator. The filter selects the desired frequency component and suppresses the undesired frequency component in the desired frequency selective adjustment path. The vector regulators repeatedly adjust the amplitude and phase values of the composite components for the desired and suppressed undesired frequency components. In this configuration, the cancellation levels of the signal cancellation loop and distortion cancellation loop are depending on the amplitude and phase errors of the vector regulator. The analysis results show that the amplitude and phase errors of the desired frequency component almost become independent that of the undesired frequency component in a weak non-linearity condition, when the isolation between the desired band and the undesired band given by the filter is more than 40 dB. The amplitude errors of the desired frequency component are dependent on that of the undesired frequency component in a strong non-linear conditions when the isolation level sets as above. A 1-W-class signal cancellation loop and 20-W-class FFPA are fabricated for 1.7-GHz and 2.1-GHz bands simultaneous operation. The experimental results show that the analysis results are suitable in the experimental conditions. From these investigations, the analysis results can provide a commercially available dual-band FFPA. To our best knowledge, this is first analysis results for the dual-band FFPA.

A spectrum suppressed transmission that increases the frequency utilization efficiency, defined as throughput/bandwidth, by suppressing the required bandwidth has been proposed. This is one of the most effective schemes to solve the exhaustion problem of frequency bandwidths. However, in spectrum suppressed transmission, its transmission quality potentially degrades due to the ISI making the bandwidth narrower than the Nyquist bandwidth. In this paper, in order to improve the transmission quality degradation, we propose the spectrum suppressed transmission applying both FEC (forward error correction) and LE (linear equalization). Moreover, we also propose a new channel allocation scheme for the spectrum suppressed transmission, in multi-channel environments over a satellite transponder. From our computer simulation results, we clarify that the proposed schemes are more effective at increasing the system throughput than the scheme without spectrum suppression.

Smaller antenna structures for long-range radar transmitters and receivers operating in the 77-GHz band for automotive application have been achieved by using antennas with a horn, lens, and microstrip antenna. The transmitter (Tx) antenna height was reduced while keeping the antenna gain high and the antenna substrate small by developing an antenna structure composed of two differential horn and lens antennas in which the diameter and focus distance of the lenses were half those in the previous design. The microstrip antennas are directly connected to the differential outputs of a monolithic microwave integrated circuit. A Tx antenna fabricated using commercially available materials was 14mm high and had an output-aperture of 18×44mm. It achieved an antenna gain of 23.5dBi. The antenna substrate must be at least 96mm2. The antenna had a flat beam with half-power elevation and azimuth beamwidths of 4.5° and 21°, respectively. A receiver (Rx) antenna array composed of four sets of horn and lens antennas with an output-aperture of 9×22mm and a two-by-two array configuration was fabricated for application in a newly proposed small front-end module with azimuth direction of arrival (DOA) estimation. The Rx antenna array had an antenna coupling of less than -31dB in the 77-GHz band, which is small enough for DOA estimation by frequency-modulated continuous wave radar receivers even though the four antennas are arranged without any separation between their output-apertures.