In this paper, the relationship between correlation interval (CI) and estimate is investigated. Then a special correlation interval is explored that is adaptive to all levels of signal-to-noise ratio (SNR) and velocity conditions, and the mean square error is deduced. Finally, we propose an iterative algorithm that achieves the special correlation interval and calculates the Doppler spread by increasing the resolution on time-domain iteratively. Simulation results show that compared with conventional schemes, performance of the proposed algorithm is basically independent of velocity variation and less sensitive to SNR, especially in low SNR environments. It achieves high accurate estimation directly without any post-rectification.

This paper proposes a new echo suppressor based on spectral correlation between the residual echo and the echo replica in an ordinary echo canceller. First, it is revealed by experiments that there is a significant correlation between the spectral amplitudes of the residual echo and the echo replica, and a new model for nonlinear-echo suppression based on the correlation is derived. Next, a new echo suppressor controlling the gain in each frequency bin to suppress the residual echo based on the new model is developed. Simulation results with speech data recorded by a hands-free cellphone show that the proposed echo suppressor reduces the residual echo to an almost inaudible level.

Many applications of OFDM systems require Doppler spread estimation. This is quite difficult in multi-path fading channels with no strong direct path. This letter proposes a novel Doppler spread estimation method, which uses the mean square (MS) value of channel impulse response's time derivative. The proposed method is very simple compared with the previously proposed methods. Simulation results show that it allows easy and precise Doppler spread calculation for OFDM by using the channel estimation based on either pilot tones or pilot symbols.

In this paper, a multistage parallel interference canceller (MPIC) with multiple-beam reception for a DS-CDMA system is proposed to suppress multiple access interference (MAI) effectively. Its aim is to reduce the computational complexity of the conventional MPIC cascaded with an adaptive array antenna. It employs multiple fixed beams based on phased array and selects suitable beams to demodulate the transmitted signal of each user. Then it suppresses residual interference signals by the MPIC cascaded with multiple-beam receiver. Its bit error rate (BER) performance is evaluated by computer simulations assuming an uplink single-chip-rate multiple-spreading-factor DS-CDMA system over both exponentially decaying 5-path and equal average power 2-path Rayleigh distributed channels. When there are 16 users in an 120-sectored single cell, the proposed receiver with 6-element array antenna and 2-stage MPIC shows better or comparable BER performance compared with that of the conventional receiver. Moreover, the proposed receiver with 8 beams can reduce the number of complex multiplications to about 40% of that of the complexity-reduced conventional receiver over 5-path channels.

Design of optimal controllers satisfying performance criteria of minimum tracking error and disturbance level for an interval system using a multi-objective evolutionary approach is proposed in this paper. Based on a worst-case design philosophy, the design problem is formulated as a minimax optimization problem, subsequently solved by a proposed two-phase multi-objective genetic algorithm (MOGA). By using two sets of interactive genetic algorithms where the first one determines the maximum (worst-case) cost function values for a given set of controller parameters while the other one minimizes the maximum cost function values passed from the first genetic algorithm, the proposed approach evolutionarily derives the optimal controllers for the interval system. To suitably assess chromosomes for their fitness in a population, root locations of the 32 generalized Kharitonov polynomials will be used to establish a constraints handling mechanism, based on which a fitness function can be constructed for effective evaluation of the chromosomes. Because of the time-consuming process that genetic algorithms generally exhibit, particularly the problem nature of minimax optimization, a parallel computation scheme for the evolutionary approach in the MATLAB-based working environment is also proposed to accelerate the design process.

To increase the yield of data processing circuits such as adders and logic operation circuits, the bit-slice reconfiguration design has been proposed as an efficient redundant technology for defect-tolerance. Wallace multipliers are a well-known class of high-speed parallel multipliers. Unfortunately, the bit-slice reconfiguration design is not applicable to Wallace multipliers because Wallace multipliers do not have regular bit-slice structure. Therefore, redundant designs for Wallace multipliers have been regarded impossible. This paper proposes a redundant design for Wallace multipliers. In order to design redundant Wallace multipliers, first, 2n heterogeneous slices are considered in a non-redundant nn Wallace multiplier. The proposed redundant Wallace multipliers contain reconfigurable slices which can play the role of both i-th and (i+1)-th slices. Since the i-th slice has a similar structure to the (i+1)-th slice, the reconfigurable slice is not much larger than the i-th slice. This paper also shows a repair procedure for the proposed design. This paper evaluates the proposed design from the viewpoint of the yield, area, effective yield and delay time. For example, the yield of a 3232 Wallace multiplier increases from 0.30 to 0.41 by applying the proposed design while the area increases by a factor of 1.21.

At present, during the design of sealed electromagnetic relay, the tolerances of design parameters are given with experience. The designer can't provide quantificational reliability index, and the blindness of tolerance distribution also causes unnecessary increase of machining cost. According to the study of electromagnetic force and spring force characteristics of a certain sealed electromagnetic relay with polarized magnetic system, this paper analyzed the influence of main design parameters' tolerances to the tolerance bands of electromagnetic force and spring force characteristics and achieved the strong correlative factors (viz. design parameters) that have obvious effect on tolerance bands of electromagnetic force and spring force characteristics. Then based on the calculation of reliability, the tolerance distribution method of key design parameters was given. This method not only can make the designed product satisfy requirement of reliability, but also reduce the machining cost.

To achieve a very high data rate within a limited frequency band in orthogonal frequency division multiplexing (OFDM) systems, multi-input multi-output (MIMO) techniques are very promising. Moreover, if a transmitter has the channel state information (CSI), the achievable spectrum efficiency can be maximized using the eigenbeam-space division multiplexing (E-SDM). However, this scheme demands accurate channel estimation. Therefore, in a closed-loop transmission scheme, an increase in the amount of feedback is absolutely necessary for the E-SDM. This paper describes a downlink beamforming method that significantly reduces the amount of feedback needed by using the common transmission weight vectors in all sub-carriers, compared to the amount required for E-SDM. The proposed method also applies transmission diversity to compensate for the quality. The effectiveness of the proposed method was confirmed using computer simulations in both Ricean and Rayleigh fading environments.

A novel dual band transmitter module for 2.4 GHz and 5.8 GHz wireless LAN applications with adaptive digital predistortion linearization is presented. The module operates either as a power amplifier for 2.4 GHz or frequency doubler for 5.8 GHz band. Amplification gain is 12.9 dB at 2.4 GHz and multiplication gain is 3.3 dB at 5.8 GHz. At 2.4 GHz band, the second harmonic is about 36.5 dB lower than the fundamental, and the 2.9 GHz fundamental signal is 20.3 dB lower than the second harmonic output at 5.8 GHz operation. An adaptive digital predistortion scheme is proposed to linearize the 2.4 GHz amplifier, and to get the proper 5.8 GHz band wireless LAN signal. The 2.4 GHz amplifier with predistortion satisfies the ACPR mask requirement for the input 1 dB compression power of 5 dBm and the linearized frequency doubler shows 26 dB ACPR improvement at 11 MHz offset from center frequency by using the proposed predistortion linearization. The frequency doubler output spectrum with predistortion does meet the IEEE standard Tx mask.

The authors propose a single-layer hollow-waveguide 8-way Butler matrix. All components of the Butler matrix are in a single layer which contributes to low-cost fabrication. To reduce the length of the couplers, a step structure is installed in the coupled region. 50% length reduction is obtained in comparison with the conventional design using reflection-suppressing posts in the coupled region. The total size of the matrix is 17.1λg6.0λg. The full structure of the matrix is fabricated by hollow waveguides at 22 GHz band and the total measured loss is only 0.25 dB.

In 2005, Yong and Lee proposed a buyer-seller fingerprinting protocol using symmetric and commutative encryptions. They claimed that their protocol was practical and anonymous since they used symmetric and commutative encryptions. However, an attacker can get the content embedded with one or more honest buyers' fingerprints using man-in-the-middle attack. In this letter, we point out the weakness and propose methods for improving to their protocol.

The delay characteristics of the MPsLS, a data forwarding scheme used for a core area of the integrated data service network, are discussed and analyzed. MPsLS has the capability of guaranteeing QoS on the per-flow level for time-sensitive applications and simultaneously maintaining the high utilization of network resources. In the MPsLS core area, the forwarding process is implemented with a fine-grain slot synchronization model, and at the ingress edge nodes, the forwarding process is carried with a coarse-grain frame synchronization model. The delay analyses are done according to three service models: the exact synchronization model, the less strict synchronization model for the appointed channels, and an asynchronous model for the filler channels. The authors give estimation equations of mean delay between edge-to-edge nodes in an MPsLS network, and introduce an effective method to determine the reserved bandwidth for given application flows based on numerical calculations from those theory analysis and simple simulation results.

A new stereo echo canceler with input slides and counter-lateralization is proposed. Convergence of filter coefficients to the correct echo paths is obtained by pre-processing which delays the input signal periodically by one sample in one of the two channels. The time difference between the two stereo components of the input signals causes a shift of the sound image. This shift is compensated for by presenting the delayed component of the stereo signals to a loudspeaker at a higher intensity, and the other component at a lower intensity. Correct echo-path identification is analytically shown in a more general form than in the preceding literatures. A subjective listening test shows that this method is more effective for vocal musics. The processed signals are scored 0.45 lower than the original input signals, using the ITU-R five-grade impairment scale.

In this paper, we propose a new method to enhance the fault-tolerance of the Content Addressable Network (CAN), which is known as a typical pure P2P system based on the notion of Distributed Hash Table (DHT). The basic idea of the proposed method is to introduce redundancy to the management of index information distributed over the nodes in the given P2P network, by allowing each index to be assigned to several nodes, which was restricted to be one in the original CAN system. To keep the consistency among several copies of indices, we propose an efficient synchronization scheme based on the notion of labels assigned to each copy in a distinct manner. The performance of the proposed scheme is evaluated by simulation. The result of simulations indicates that the proposed scheme significantly enhances the fault-tolerance of the CAN system.

Four 50% duty-cycle divide-by-3 prescalers--positively/ negatively triggered sample-sample-hold (SSH) and sample-hold-hold (SHH) prescalers--are designed based on the current switchable D flip-flops and discussed in this paper. The positively triggered SSH and SHH prescalers are fabricated using the 0.35-µm SiGe BiCMOS technology and measured by the real-time oscilloscope and the spectrum analyzer. The SHH prescaler is our proposed structure and demonstrated in this paper. According to the measurement results, under the condition of the same input power, its maximum operation frequency is twice as high as that of the SSH prescaler thanks to better signal synchronization. At 2.7 V supply, the SSH prescaler operates from 500 MHz to 2 GHz as the SHH prescaler performs from 1 GHz to 3.4 GHz. The input sensitivity level of both structures is about -5 dBm, while the maximum output power is also about -5 dBm. The core current consumption is 4.538 mA and 4.258 mA for the SSH and SHH prescalers, respectively.

A 32-bit embedded RISC microcontroller core targeted for automotive, industrial, and PC-peripheral applications has been developed to offer the smaller code size, lower-latency instruction and interrupt processing needed for next-generation microcontrollers. The 360 MIPS/400MFLOPS/200 MHz core--based on the Harvard bus architecture--uses 0.13/0.15-µm CMOS technology and consists of a CPU, FPU, and register banks. To reduce the size of the control programs, new instructions have been added to the instruction set. These new instructions, as well as an enhanced C compiler, produce object files about 25% smaller than those for a previous designed core. A dual-issue superscalar structure consisting of three- or five-stage pipelines provides instruction processing with low latency. The cycle performance is thus an average of 1.8 times faster than the previous designed core. The superscalar structure is used to save 19 CPU registers in parallel when executing interrupt processing. That is, it saves the 19 CPU registers to the resister bank by accessing four registers at a time. This structure significantly improves interrupt response time from 37 cycles to 6 cycles.

In this paper, we propose a protocol for multicast communication called Multicast Datagram Transfer Protocol (MDTP) to provide multicast for video broadcasting service on the Internet. MDTP is a one-to-many multicast communication protocol, which is constructed based on IPv4 unicast protocol by utilizing IP Router Alert Option, and it uses unicast addressing and unicast routing protocol. A mechanism is presented to allow a router to remove identical video stream, to duplicate a video stream, and to forward each copy of the duplicated video stream to its destinations. Ordinary IP routers that do not support MDTP will treat the MDTP packets as normal unicast packets. Hence, gradual deployment is possible without tunneling technique. With a delegation mechanism, MDTP router is also able to handle request from clients, and serve the requested video stream. The simulation results show that the average bandwidth usage of MDTP is close to the average bandwidth usage of IP multicast. MDTP also has greater efficiency than XCAST, and its efficiency becomes significant for a large number of clients.

A 2-bit operational metal/silicon-oxide-nitride-oxide-silicon (MONOS/SONOS) nonvolatile memory using an asymmetric double-gate (ASDG) MOSFET was studied to double flash memory density. The 2-bit programming and erasing was performed by Fowler-Nordheim (FN) tunneling in a NAND array architecture using individually controlled gates. A threshold voltage shift of programmed states for the 2-bit operation was investigated with the aid of a SILVACO® simulator in both sides of the gate by changing gate workfunctions and tunneling oxide thicknesses. In this paper, the scalability of the device down to 30 nm was demonstrated by numerical simulation. Additionally, guidelines of the 2-bit ASDG nonvolatile memory (NVM) structure and operational conditions were proposed for "program," "read," and "erase."

The goal of this study was to design a practical fuzzy controller of the cycle-to-cycle control for multi-joint movements of swing phase of functional electrical stimulation (FES) induced gait. First, we designed three fuzzy controllers (a fixed fuzzy controller, a fuzzy controller with parameter adjustment based on the gradient descent method, and a fuzzy controller with parameter adjustment based on a fuzzy model) and two PID controllers (a fixed PID and an adaptive PID controllers) for controlling two-joint (knee and ankle) movements. Control capabilities of the designed controllers were tested in automatic generation of stimulation burst duration and in compensation of muscle fatigue through computer simulations using a musculo-skeletal model. The fuzzy controllers showed better responses than the PID controllers in the both control capabilities. The parameter adjustment based on the fuzzy model was shown to be effective when oscillating response was caused due to the inter-subject variability. Based on these results, we designed the fuzzy controller with the parameter adjustment realized using the fuzzy model for controlling three-joint (hip, knee, and ankle) movements. The controlled gait pattern obtained by computer simulation was not significantly different from the normal gait pattern and it could be qualitatively accepted in clinical FES gait control. The fuzzy controller designed for the cycle-to-cycle control for multi-joint movements during the swing phase of the FES gait was expected to be examined clinically.

In closed-loop multiple-input and multiple-output space-division multiplexing (MIMO-SDM) systems, allocating power among multiple transmit data streams improves the channel capacity. However, the optimum power allocation values are not always available in closed-form. For instance, when we use transmission and reception schemes that do not transfer the MIMO channel into parallel orthogonal channels (e.g., eigen-mode SDM), the signal to interference plus noise ratio (SINR) of each data stream at the output of the receiver is not proportional to its corresponding transmit power. This feature makes it difficult to obtain the optimal closed-form power allocation value for each data stream. Thus, in this paper, we propose an iterative power allocation scheme for MIMO-SDM systems where the SINR is not proportional to the transmit power. Furthermore, we incorporate a transmit antenna selection scheme into the proposed power allocation scheme in order to attain further capacity enhancement. Computer simulation results are provided to show the effectiveness of the proposed power allocation schemes.