Blind source separation (BSS) techniques are required for various signal decomposing issues. Independent component analysis (ICA), assuming only a statistical independence among stochastic source signals, is one of the most useful BSS tools because it does not need a priori information on each source. However, there are many requirements for decomposing multiple deterministic signals such as complex sinusoidal signals with different frequencies. These requirements may include pulse compression or clutter rejection. It has been theoretically shown that an ICA algorithm based on maximizing non-Gaussianity successfully decomposes such deterministic signals. However, this ICA algorithm does not maintain a sufficient separation performance when the frequency difference of the sinusoidal waves becomes less than a nominal frequency resolution. To solve this problem, this paper proposes a super-resolution algorithm for complex sinusoidal signals by extending the maximum likelihood ICA, where the probability density function (PDF) of a complex sinusoidal signal is exploited as a priori knowledge, in which the PDF of the signal amplitude is approximated as a Gaussian distribution with an extremely small standard deviation. Furthermore, we introduce an optimization process for this standard deviation to avoid divergence in updating the reconstruction matrix. Numerical simulations verify that our proposed algorithm remarkably enhances the separation performance compared to the conventional one, and accomplishes a super-resolution separation even in noisy situations.

This paper proposes a low-complexity concatenated (LCC) soft-in soft-out (SISO) detector for spreading OFDM systems. The LCC SISO detector uses the turbo principle to compute the extrinsic information of the optimal maximum a priori probability (MAP) SISO detector with extremely low complexity. To develop the LCC SISO detector, we first partition the spreading matrix into some concatenated sparse matrices separated by interleavers. Then, we use the turbo principle to concatenate some SISO detectors, which are separated by de-interleavers or interleavers. Each SISO detector computes the soft information for each sparse matrix. By exchanging the soft information between the SISO detectors, we find the extrinsic information of the MAP SISO detector with extremely low complexity. Simulation results show that using the LCC SISO detector produces a near-optimal performance for both uncoded and coded spreading OFDM systems. In addition, by using the LCC SISO detector, the spreading OFDM system significantly improves the BER of the conventional OFDM system.

A numerical model of multi-layered organic light emitting diode (OLED) is presented in this paper. The current density-voltage (J-V) model for OLED was performed by using the injection-limited current and bulk-limited current. The mobility equation was based on the field dependent model, so called “Poole-Frenkel mobility model.” The accuracy of this simulation was represented by comparing to the experimental results with a variable of EML thickness of multi-layered OLED device. There are two hetero-junction models which should be dealt with in the simulation. The Langevin recombination rate of electron and hole is also calculated through the device simulation.

This paper presents a new 8T (8-transistor) SRAM cell layout mitigating multiple-bit upset (MBU) in a divided wordline structure. Because bitlines along unselected columns are not activated, the divided wordline structure eliminates a half-select problem and achieves low-power operation, which is often preferred for low-power/low-voltage applications. However, the conventional 8T SRAM with the divided wordline structure engenders MBUs because all bits in the same word are physically adjoining. Consequently, it is difficult to apply an error correction coding (ECC) technique to it. In this paper, we propose a new 8T cell layout pattern that separates internal latches in SRAM cells using both an n-well and a p-substrate. We saw that a SEU cross section of nMOS is 3.5–4.5 times higher than that of pMOS (SEU: single event upset; a cross section signifies a sensitive area to soft error effects). By using a soft-error simulator, iRoC TFIT, we confirmed that the proposed 8T cell has better neutron-induced MBU tolerance. The simulator includes soft-error measurement data in a commercial 65-nm process. The MBU in the proposed 8T SRAM is improved by 90.70% and the MBU soft error rate (SER) is decreased to 3.46 FIT at 0.9 V when ECC is implemented (FIT: failure in time). Additionally, we conducted Synopsys 3-D TCAD simulation, which indicates that the linear energy transfer (LET) threshold in SEU is also improved by 66% in the proposed 8T SRAM by a common-mode effect.

Computational Fluid Dynamics (CFD) is used as a common design tool in the aerospace industry. UPACS, a package for CFD, is convenient for users, since a customized simulator can be built just by selecting desired functions. The problem is its computation speed, which is difficult to enhance by using the clusters due to its complex memory access patterns. As an economical solution, accelerators using FPGAs are hopeful candidate. However, the total scale of UPACS is too large to be implemented on small numbers of FPGAs. For cost efficient implementation, partial reconfiguration which dynamically loads only required functions is proposed in this paper. Here, the MUSCL scheme, which is used frequently in UPACS, is selected as a target. Partial reconfiguration is applied to the flux limiter functions (FLF) in MUSCL. Four FLFs are implemented for Turbulence MUSCL (TMUSCL) and eight FLFs are for Convection MUSCL (CMUSCL). All FLFs are developed independently and separated from the top MUSCL module. At start-up, only required FLFs are selected and deployed in the system without interfering the other modules. This implementation has successfully reduced the resource utilization by 44% to 63%. Total power consumption also reduced by 33%. Configuration speed is improved by 34-times faster as compared to full reconfiguration method. All implemented functions achieved at least 17 times speed-up performance compared with the software implementation.

We propose a new configuration for a parallel fiber amplifier that can amplify both the C- and L-bands simultaneously by employing bundled Er3+-doped fiber (EDF). The bundled EDF is a candidate amplification medium for multi-core optical fiber amplifiers. Our parallel fiber amplifier is another application of the multi-core amplification medium. The amplifier achieves almost the same signal gain of 20 dB for both the C- and L-bands by using a bundled EDF, which is realized by bundling seven identical single-core EDFs.

This paper presents a compact metal plate lens antenna for evaluating a wave absorber placed on ceiling of the ETC gate. The focal distance of the lens was derived to be 129 cm by the geometrical optics procedure. By arranging the lens in front of a horn antenna, the gain and beamwidth characteristics were improved from 18 dBi to 26 dBi and from 22 degrees to 7 degrees, respectively. Then the antenna characteristics were evaluated when the distance between the antenna and the lens was changed in order to miniaturize the lens antenna. As the result, the changes in beamwidth were held to within 1 dB when the lens came close to the horn antenna. Scattering, phase and electric field intensity of electromagnetic wave were evaluated to clarify the foundation of the given characteristics. It was found that the field intensity for the miniaturized lens antenna is stronger than that for GO designed one though the phase uniformity is worse. The distance between the horn antenna and lens can be reduced to 80 cm. The absorption characteristics for the arranged absorbers which have different absorptions were measured, and it was shown that the proposed method was suitable for specifying the deteriorated absorber in the ETC system.

A new information detection method has been proposed for a very fast and efficient search engine. This method is implemented on hardware system using FPGA. We take advantages of Content Addressable Memory (CAM) which has an ability of matching mode for designing the system. The CAM blocks have been designed using available memory blocks of the FPGA device to save access times of the whole system. The entire memory can return multi-match results concurrently. The system operates based on the CAMs for pattern matching, in a parallel manner, to output multiple addresses of multi-match results. Based on the parallel multi-match operations, the system can be applied for pattern matching with various required constraint conditions without using any search principles. The very fast multi-match results are achieved at 60 ns with the operation frequency 50 MHz. This increases the search performance of the information detection system which uses this method as the core system.

In order to improve the detection performance in passive millimeter-wave (PMMW) imaging, a new method forwarding a null in the direction of human body and objects is proposed. The forward-nulling PMMW imaging using a dielectric tube occupied by cooling water placed near the focus line of a parabolic cylinder are performed. It is shown experimentally that the contrast between human body and conducting objects such as a conducting plate and a conducting sphere is improved by the presence of the cooling dielectric tube and parabolic cylinder.

Single front-end architecture with parasitic antenna element (PAE) in compact array system has been proposed for enhancing spectral efficiency and miniaturizing the receiver. Although most of studies paid attention to design optimal receiver with antenna mutual coupling on fading correlation, relatively little attention has been paid to noise. In this paper, we propose a low noise model for single front-end MIMO receiver system with PAE which includes arbitrary signal and noise coupling. The proposed model articulates physical noise sources and relates their spatial correlation with array receive antennas, parasitic element, front-end and matching circuit. A matching circuit is designed to achieve minimum noise figure. After that, the optimal PAE value is derived to maximize channel capacity. We present numerical analysis to verify the proposed system on certain conditions.

Orthogonal Frequency Division Multiple Access (OFD-MA) is a leading air interface candidate for future generation cellular networks. However, if deployed in a multi-user multi-tier cellular system, it is important to fairly share radio resources such as transmission power and sub-carriers among co-tier and cross-tier users. This paper focuses on a mathematical formulation of cell inner-zone/outer-zone radio resource partitioning variables and considers the case of an FFR-based macrocell underlaid with femtocell. By applying an exhaustive search procedure on the developed formulation, we determine the optimal radio resource partitioning parameter values from the perspectives of macrocell user fairness and femtocell throughput maximization.

It is becoming more and more important to make use of personal or classified information while keeping it confidential. A promising tool for meeting this challenge is secure multi-party computation (MPC). It enables multiple parties, each given a snippet of a secret s, to compute a function f(s) by communicating with each other without revealing s. However, one of the biggest problems with MPC is that it requires a vast amount of communication. Much research has gone into making each protocol (equality testing, interval testing, etc.) more efficient. In this work, we make a set of multiple protocols more efficient by transforming them into their equivalent batch processing form and propose two protocols: “Batch Logical OR” and “Batch Logical AND.” Using proposed protocols recursively, we also propose “Batch Logical OR-AND” and “Batch Logical AND-OR,” and show arbitrary formula consisting of Boolean protocols, OR gates, and AND gates can be batched. Existing logical OR and logical AND protocols consisting of t equality testing invocations have a communication complexity of O(t), where is the bit length of the secrets. Our batched versions of these protocols reduce it to O( + t). For t interval testing invocations, they reduce both communication and round complexity. Thus they can make the queries on a secret shared database more efficient. For example, the use of the proposed protocols reduces the communication complexity for a query consisting of equality testing and interval testing by approximately 70% compared to the use of the corresponding existing protocols. The concept of the proposed protocols is versatile and can be applied to logical formulae consisting of protocols other than equality testing and interval testing, thereby making them more efficient as well.

This paper proposes a verification-aware design methodology that provides developers with a systematic and reliable approach to performing thread-pipelining parallelization on sequential programs. In contrast to traditional design flow, a behavior-model program is constructed before parallelizing as a bridge to help developers gradually leverage the technique of thread-pipelining parallelization. The proposed methodology integrates verification mechanisms into the design flow. To demonstrate the practicality of the proposed methodology, we applied it to the parallelization of a 3D depth map generator with thread pipelining. The parallel 3D depth map generator was further integrated into a 3D video playing system for evaluation of the verification overheads of the proposed methodology and the system performance. The results show the parallel system can achieve 33.72 fps in D1 resolution and 12.22 fps in HD720 resolution through a five-stage pipeline. When verifying the parallel program, the proposed verification approach keeps the performance degradation within 23% and 21.1% in D1 and HD720 resolutions, respectively.

All points on the Pareto boundary can be obtained by solving the weighted sum rate maximization problem for some weighted coefficients. Unfortunately, the problem is non-convex and difficult to solve without performing an exhaustive search. In this paper, we propose an optimal distributed beamforming strategy for the two-user multiple-input single-output (MISO) interference channel (IC). Through minimizing the interference signal power leaked to the other receiver for fixed useful signal power received at the intended receiver, the original non-convex optimization problem can be converted into a family of convex optimization problems, each which can be solved in distributed manner with only local channel state information at each transmitter. After some conversion, we derive the closed-form solutions to all Pareto optimal points based on a game-theoretic viewpoint which indicates that linear combinations of the maximum-ratio transmit (MRT) and zero-forcing (ZF) beamforming strategies can achieve any point on the Pareto boundary of the rate region for the two-user MISO interference channel, and the only computation involved is to solve a basic quadratic equation. Finally, the result is validated via numerical simulations.

This paper develops a methodology of crosstalk analysis/measurement techniques for the design and fabrication of the MEMs (Micro-ElectroMichanical system) probe card. By introducing more ground pins into the connector pins, the crosstalk characteristics can be enhanced and a design guide for the parameters, such as pin's size and pitch is proposed to satisfy the given crosstalk limitation of -30 dB for reliable high speed signal transfer. The paper also presents a novel method to characterize scattering parameters of multiport interconnect circuits with a 4-port VNA (Vector Network Analyzer). By employing the re-normalization of scattering matrices with different reference impedances at other ports, data obtained from 4-port configuration measurements can be synthesized to build a full scattering matrix of the DUT (Device-Under-Test, MEMs probe connector pins). In comparison to the conventional 2-port VNA re-normalization method, proposed technique has two advantages: saving of measuring time, and enhanced accuracy even with open-ended unmeasured ports. A good agreement of the estimated and correct S parameters verifies the validness of the proposed algorithm.

This letter proposes a simple heuristic to identify the discrete-time switched autoregressive exogenous (SARX) systems. The goal of the identification is to identify the switching sequence and the system parameters of all submodels simultaneously. In this letter the SARX system identification problem is formulated as the l0 norm minimization problem, and an iterative algorithm is proposed by applying the reweighted least squares technique. Although the proposed algorithm is heuristic, the numerical examples show its efficiency and robustness for noise.

A facial components based facial expression recognition algorithm with sparse representation classifier is proposed. Sparse representation classifier is based on sparse representation and computed by L1-norm minimization problem on facial components. The features of “important” training samples are selected to represent test sample. Furthermore, fuzzy integral is utilized to fuse individual classifiers for facial components. Experiments for frontal views and partially occluded facial images show that this method is efficient and robust to partial occlusion on facial images.

The non-homogeneous Poisson process (NHPP) has been applied successfully to model nonstationary counting phenomena for a large class of problems. In software reliability engineering, the NHPP-based software reliability models (SRMs) are of a very important class. Since NHPP is characterized by its rate (intensity) function, which is known as the software failure rate of NHPP-based SRM, it is of great interest to estimate accurately the rate function from observed software failure data. In the existing work the same authors introduced a Haar-wavelet-based technique for this problem and found that the Haar wavelet transform provided a very powerful performance in estimating software failure rate. In this paper, we consider the application potentiality of a Daubechies wavelet estimator in the estimation of software failure rate, given the software failure time data. We give practical solutions by overcoming technical difficulties in applying the Daubechies wavelet estimator to the real software failure time data.

Entangled states play crucial roles in quantum information theory and its applied technologies. In various protocols such as quantum teleportation and quantum key distribution, a good entangled state shared by a pair of distant players is indispensable. In this paper, we numerically examine entanglement sharing protocols using quantum LDPC CSS codes. The sum-product decoding method enables us to detect uncorrectable errors, and thus, two protocols, Detection and Resending (DR) protocol and Non-Detection (ND) protocol are considered. In DR protocol, the players abort the protocol and repeat it if they detect the uncorrectable errors, whereas in ND protocol they do not abort the protocol. We show that DR protocol yields smaller error rate than ND protocol. In addition, it is shown that rather high reliability can be achieved by DR protocol with quantum LDPC CSS codes.

Arc discharge generated by breaking electrical contact is considered as a main source of not only degradation of the electrical property but also an undesired electromagnetic (EM) noise. In order to clarify the effect of heated temperature on the bridge, arc-duration and the fluctuation of voltage, opening-waveforms at slowly separating silver-tin dioxide contact with holder heating are measured and discussed experimentally in this paper. Firstly, opening-waveforms are measured. Secondly, voltage fluctuation of the each arc-phase is discussed to extract the effect of the heated holder. The relationship between temperature of the heated holder and duration and fluctuation of the arc was investigated experimentally. It was revealed that as the initial temperature of the heated holder becomes higher, arc-duration becomes slightly longer. In addition, voltage fluctuation at the gaseous-phase decreases when the holder is heated. Consequently, the heated holder can suppress the voltage fluctuation even if its duration becomes slightly longer.