The diverse broadcast means that will be available in the future will cause an increased demand for programs. When the input of the posture of an agent is used to manipulate a virtual computer graphics actor, it is better if the system does not require a special studio and devices. In the present paper, we propose a way to extract images from a single picture based on estimates of blooming. This is done using a partial auto-correlation analysis that carries out backward and forward predictions simultaneously. And, we divide targets into the stratified depth from a single image. An experiment was conducted using a picture taken with a digital camera, and satisfactory results were obtained.

Currently, the most popular model in data compression theory is that of stationary ergodic sources. But there do exist sequences each of which is not emitted from any stationary ergodic source but can be compressed sufficiently by a certain algorithm. We estimate the size of the set of such sequences in terms of Hausdorff dimension.

The ring-like systolic array architecture described in this paper, based on a conventional one-dimensional systolic array architecture, was created through operator rescheduling based on the symmetry of data flow. This eliminated high-latency delay due to the stuffing of the array pipeline in the conventional architecture. The new architecture requires a memory bandwidth no greater than the conventional architecture does, but increases throughput and processor utilization while reducing power consumption.

A chemical shift MR method which utilizes a oscillating gradient field is presented in this paper. Frequency modulation resulting from oscillating a gradient field spreads the spectrum that contains both chemical shift and spatial information, over a wide frequency range by using a large modulation factor in FM. The chemical shift spectrum resides within every frequency band segmented by the modulation frequency ωm. The spectral elements gathered from all such frequency segments for a chemical shift frequency contain the spatial image of that particular chemical shift frequency, despite the distortion introduced by a series of the Bessel functions acting as a point spread function. A sum of several Bessel functions of the first kind Jn(. ) is used to approximate the deconvolution process, since the sum staggered with respect to n has a desirable peaking property useful in deconvolution. This leads to devise a new image reconstruction algorithm based on the simple moving average over the spatial coordinate for which the oscillating gradient is applied. Furthermore, the number of echo measurements necessary for an image size of N N is reduced from N2 of the spin echo chemical shift imaging down to N by this method. Simulation results supporting the validity of this method are also presented in this paper.

Precise simulation of non-quasi-static (NQS) characteristics is crucial for the analog application of MOS transistors. This paper presents the small signal admittance model of four-terminal NQS MOS transistors by solving the differential equation derived from the primary principle. The model contains the bulk-charge effect, the mobility reduction, and the velocity saturation. The results are compared with those for the conventional quasi-static model, the BSIM3v3 NQS model, and the 2-D device simulation.

By using full-color light emitting diode (LED) panel, we have been studying a stereoscopic full-color large television in broad daylight. In order to implement stereoscopic large display for the general public, optimum parameters of display elements and parallax barrier and viewing areas of stereoscopic display using parallax barrier are discussed. Although stereoscopic display with parallax barrier permits the viewer to view stereoscopic images without any special glasses, its viewing area is restricted by crosstalk and disappearing of pixels. Enlarged viewing areas, which are derived from the small ratio of light emitting region to pixel and a proper aperture ratio of parallax barrier, are analyzed. A model of a viewer standing toward the display is proposed because the viewer apart from the horizontal center of the display turns to the center point of LED display and this turning causes a deviation of viewer's eye position. Then, the allowable number of viewing locations is derived on "no crosstalk" and "no disappearance" conditions. The optimum aperture ratio of parallax barrier and the width of light emitting region is obtained through the optimization. The viewing area obtained from the analysis is confirmed by experiments using full-color LED panel. Relations between viewing area and the moire fringes is also discussed. The depth of the viewing area agrees the viewing distance where no moire fringe appears. Furthermore, possibility of display for the crowds is discussed.

In this paper, as a practical application, we focus on the genetic algorithm (GA) for multi-head surface mounting machines which are used to populate printed circuit boards (PCBs). Although there have been numerous studies on the surface mounting machine, studies on the multi-head case are rare because of its complexity. The multi-head surface mounting machine can pick multiple components simultaneously in one pickup operation and this operation can reduce much portion of the assembly time. Hence we try to minimize the assembly time by maximizing the number of simultaneous pickups, resulting in reduction of PCB production cost. This research introduces a partial-link GA method for the single-head case. Then, we apply this method to the multi-head case by regarding a reel-group as one reel and a component-cluster as one component. The results of computer simulation show that our genetic algorithm is greatly superior to the heuristic algorithm that is currently used in industry.

The contribution of the paper is two-fold: Firstly, a review of the point set registration literature is given, and secondly, a novel covariance weighted least squares formulation of the multiple view point set registration problem is presented. Point data for surface registration is commonly obtained by non-contact, 3D surface sensors such as scanning laser range finders or structured light systems. Our formulation allows the specification of anisotropic and heteroscedastic (point dependent) 3D noise distributions for each measured point. In contrast, previous algorithms have generally assumed an isotropic sensor noise model, which cannot accurately describe the sensor noise characteristics. For cases where the point measurements are heteroscedastically and anisotropically distributed, registration results obtained with the proposed method show improved accuracy over those produced by an unweighted least squares formulation. Results are presented for both synthetic and real data sets to demonstrate the accuracy and effectiveness of the proposed technique.

We propose here a time-domain shooting algorithm for calculating the steady-state responses of nonlinear RF circuits containing parasitic elements that is based on both a modified Newton and a secant methods. Bipolar transistors and MOSFETs in ICs have small parasitic capacitors among their terminals. We can not neglect them because they will gives large effects to the shooting algorithm at the high frequency. Since our purpose is to develop a user friendly simulator, we mainly take into account the relatively large normal capacitors such as coupling and/or by-pass capacitors and so on, because the parasitic capacitors are usually smaller and contained in the device models. We have developed a very simple simulator only using the fundamental tools of SPICE, which can be applied to relatively large scale ICs, efficiently.

This paper presents a new technique for accurately modeling uni-directional High-Voltage lightly-doped- drain MOS (HV MOS) devices by extending the bi- directional HV MOS model and adopting a new parameter extraction method. We have already reported on a SPICE model for bi-directional HV MOS devices based on BSIM3v3. However, if we apply this bi- directional HV MOS model and its parameter extraction technique directly to uni-directional HV MOS devices, there are large discrepancies between the measured and simulated I-V characteristics of the uni- directional devices. This paper extends the bi- directional HV MOS model, and adopts a new parameter extraction technique. Using parameters extracted with the new method, the simulated I-V characteristics of the uni-directional n-channel HV MOS device match the measured results well. Since our method does not change any model equations of BSIM3v3, it can be applied to any SPICE simulator on which the BSIM3v3 model runs.

This paper presents an architecture for a single-chip MPEG-2 video encoder and demonstrates its flexibility and usefulness. The architecture based on three-layer cooperation provides flexible data-transfer that improves the encoder from the standpoints of versatility, scalability, and video quality. The LSI was successfully fabricated in the 0.25-µm four-metal CMOS process. Its small size and its low power consumption make it ideal for a wide range of applications, such as DVD recorders, PC-card encoders and HDTV encoders.

A quantization-based watermarking system for motion pictures is proposed. In particular, methods for improving the image quality of watermarked video, the watermarking data tolerance, and the accuracy of watermark data detection are described. A quantitative evaluation of the reliability of watermarked data, which has not generally been discussed up to now, is also performed.

An analytical solution of the London equation for the weakly coupled grain model of high Tc superconducting thin films has been obtained in the case of finite thickness by taking full account of anisotropic conductivities. Using the solution, we provide general expressions for the transmission-line parameters of high Tc superconducting transmission lines. Dependences of the inductance and resistance on the grain size, coupling strength and film thickness have been numerically evaluated and discussed.

Thermal stability of anisotropic and isotropic Co alloy thin-film media is investigated. The orientation ratio of CoCrTa(Pt)/Cr media was controlled by the mechanical texture of the NiP/Al substrates. Bulk magnetic properties, delta M curves and time decay of magnetization in the circumferential and radial directions were measured. The maximum magnetic viscosity coefficient calculated from the time decay of magnetization in the circumferential direction was higher than that in the radial direction for a mechanically textured sample, while it was similar in both directions for a non-textured sample. The magnetic viscosity coefficient in the circumferential direction is smaller than that in the radial direction when the reverse field is in the range of the demagnetization field for thin-film recording media. This implies that an anisotropic sample (namely, a sample with a high orientation ratio) will be more thermally stable when it is not exposed to a large external magnetic field.

A neuron MOS transistor has a floating gate and multiple input gates which are capacitively coupling with the floating gate. Dramatic reduction in the number of transistors and interconnections was achieved by employing the neuron MOS in circuit designs. Since the neuron MOS gate electrode is electrically floating, it is not necessarily easy to calculate the floating gate potential using circuit simulator SPICE. In order to simulate floating gate neuron MOS circuits, a macromodel which calculates the floating gate potential combining resistances and dependent voltage and current sources has been proposed. Eight kinds of neuron MOS circuits were designed and fabricated by a double polysilicon two level metal 1.2 µ m CMOS process. Utilizing SPICE, all the neuron MOS circuits were confirmed to operate correctly. The apparent threshold voltage as seen from the input gate in the 2-input n-channel neuron MOS transistor is arbitrarily changed by a control gate signal. Multi-input neuron MOS inverters and neuron MOS full adder circuits have been successfully simulated. Moreover, the effectiveness of the proposed macromodel has been experimentally verified by fabricated circuit measurements. Measured results confirmed that 3-input neuron MOS inverter outputs the low level when the number of input gates to which a high level is applied is more than half of all input gates.

Human visual system can perceive 3-D structure of an object by binocular disparity, gradient of illumination (shading), occlusion, textures, perspective and so forth. Among them, binocular disparity seems to be the essentially important cues for the 3-D space perception and it is used widely for displaying 3-D visual circumstances such as in VR (virtual reality) system or 3-D TV. Visual illusions seem to be one of the phenomena which are purely reflecting the mechanism of human visual system. In the recent several years, the authors found several new types of 3-D visual illusions with binocular viewing. Entire 3-D illusory object including volume perception, transparency, dynamic illusions can be perceived only from the visual stimuli of disparity given by some inducing objects arranged with suitable relations. In this report, the authors introduced these newly found visual illusions and made some considerations on the human visual mechanism of 3-D perception and on their exploitation for new effective techniques in 3-D display. They introduced especially on the visual effect in two kinds of arrangement with occlusion and sustaining relationship between the illusory object and inducing objects. In the former case, the inducing objects which provide the stimuli were named as occlusion cues and classified into two types: contour occlusion cues and bulky occlusion cues. In the later case, those inducing objects were named as sustaining cues and a 3-D fully transparent illusory object was perceived. The perception was just like imagined from the scenes of the actions and positions of the pantomimists; then this phenomena was named as "Mime (Pantomime) Effect. " According to the positions of sustaining cues, they played different actions in this perception, and they are classified into three types: front sustaining cues, side sustaining cues and back sustaining cues. In addition, dynamic fusion and separation of volumetrical illusory objects were perceived when the visual stimuli were moving continuously between two structurally different conditions. Then the hysteresis was recognized in geometrical position between the fusion and separation. The authors believe that the occlusion cues and sustaining cues introduced in this paper could be effective clues for exploiting the new techniques for 3-D display.

An ultra-fast optoelectronic decision circuit using resonant tunneling diodes (RTD's) and a uni-traveling-carrier photodiode (UTC-PD) is proposed. The circuit employs two cascaded RTD's for ultra-fast logic operation and one UTC-PD that offers a direct optical input interface. This novel configuration is suitable for ultra-fast decision operation. Two types of decision circuits are introduced: a positive-logic type and a negative-logic type. Operations of these circuits were simulated using SPICE with precisely investigated RTD and UTC-PD models. In terms of circuit speed, 40-Gbit/s decision and 80-Gbit/s demultiplexing were expected. Furthermore, the superiority of the negative-logic type in terms of the circuit operating margin and the relationship between input peak photocurrent and effective logic swing were clarified by SPICE simulations. In order to confirm the basic functions of the circuits and the accuracy of the simulations, circuits were fabricated by monolithically integrating InP-based RTD's and UTC-PD's. The circuits successfully exhibited 40-Gbit/s decision operation and 80-Gbit/s demultiplexing operation with less than 10-mW power dissipation. The superiority of the negative-logic type circuit for the circuit operation was confirmed, and the relationship between the input peak photocurrent and the effective logic swing was as predicted.

This paper presents a low-power video A/D conversion technique using features of moving pictures. Neighboring frames in typical video sequences and neighboring pixels in each video frame are highly correlated. This property is effectively used for the video A/D conversion to reduce the number of comparators and the resulting power consumption. A set of reference voltages is given to a comparator array so that the iterative A/D conversion converges in the logarithmic order of the prediction error. Simulation results using standard moving pictures showed that the average number of iterations for the A/D conversion is less than 3 for all the moving pictures tested. In the proposed 12 b A/D converter, the number of comparators can be reduced to about 1/5 compared with that of the two-step flash A/D converters, which are commonly used for video applications. The A/D converter is particularly useful for the integration to CMOS image sensors.

We have developed an experimental 4 K 2 K pixel progressive scan color camera system. This new camera system has a data rate of 297 MHz pixel/sec and 60 frame/sec and we are sure that horizontal and vertical limiting resolution of 1500 TVL (TV lines) can be achieved on a color monitor. Instead of the previous approach of improving resolution simply by increasing the pixel count in a imager, a novel four-sensor pickup method with 2/3 inch 2 million pixel CMD (Charge Modulation Device) imagers is used in this system. These sensors have 1920 (H) 1035 (V) pixels within a 16:9 wide aspect image area and are successfully driven at 148 M pixel/sec in the progressive scan mode. In the four-sensor pickup method, two sensors are used for green and the rest are for red and blue. A spatial offset imaging method in the diagonal direction was applied to the two green sensors to improve the horizontal and vertical resolution effectively. The horizontal and vertical resolution of the red and blue signals become half that of the green signal, because only one 2 M-pixel imager is used for each signal. The resolution of this system, however, is not degraded so much because the luminance signal is mainly composed of green signals.

We address, in this paper, the main features of hybrid modes propagating in a rectangular waveguide partially filled with pseudochiral Ω-slabs. For the particular case of a uniaxial Ω-slab, we show that LSE and LSM hybrid modes can propagate in this inhomogeneously filled rectangular waveguide. The influence of the Ω-parameter, which characterizes the magnetoelectric tensors of the bianisotropic slab, on LSM modes is analyzed--namely an increase in the bandwidth for monomodal operation is reported. In addition, a field displacement effect and a variable phase shift proportional to the change of the Ω-parameter are attained. Finally, it is shown that the propagation characteristics are independent of the direction of propagation and so, unlike the case of magnetically biased ferrite loading, reciprocal devices can be achieved.