We evaluated the behavior of a multi-user multiple-input multiple-output (MIMO) system in time-varying channels using measured data. A base station for downlink or broadcast transmission requires downlink channel state information (CSI), which is outdated in time-varying environments and we encounter degraded performance due to interference. One of the countermeasures against time-variant environments is predicting channels with an autoregressive (AR) model-based method. We modified the AR prediction for a time division duplex system. We conducted measurement campaigns in indoor environments to verify the performance of the scheme of channel prediction in an actual environment and measured channel data. We obtained the bit-error rate (BER) using these data. The AR-model-based technique of prediction assuming the Jakes' model was found to reduce BER. Also, the optimum AR-model order was investigated by using the channel data we measured.

We propose a maximum likelihood estimation approach for the recovery of continuously-defined sparse signals from noisy measurements, in particular periodic sequences of Diracs, derivatives of Diracs and piecewise polynomials. The conventional approach for this problem is based on least-squares (a.k.a. annihilating filter method) and Cadzow denoising. It requires more measurements than the number of unknown parameters and mistakenly splits the derivatives of Diracs into several Diracs at different positions. Moreover, Cadzow denoising does not guarantee any optimality. The proposed approach based on maximum likelihood estimation solves all of these problems. Since the corresponding log-likelihood function is non-convex, we exploit the stochastic method called particle swarm optimization (PSO) to find the global solution. Simulation results confirm the effectiveness of the proposed approach, for a reasonable computational cost.

This paper studies the static mapping of multiple applications on embedded many-core SoCs. The mapping techniques proposed in this paper take into account both inter-application and intra-application parallelism in order to fully utilize the potential parallelism of the many-core architecture. Two approaches are proposed for static mapping: one approach is based on integer linear programming and the other is based on a greedy algorithm. Experiments show the effectiveness of the proposed techniques.

This paper deals with the problem of underdetermined blind source separation (BSS) where the number of sources is unknown. We propose a BSS approach that simultaneously estimates the number of sources, separates the sources based on the sparseness of speech, estimates the direction of arrival of each source, and performs permutation alignment. We confirmed experimentally that reasonably good separation was obtained with the present method without specifying the number of sources.

Vehicles' speed is one of the key factors in vehicle travel efficiency, as speed is related to vehicle travel time, travel safety, fuel consumption, and exhaust gas emissions (e.g., CO2 emissions). Therefore, to improve the travel efficiency, a recommended speed calculation scheme is proposed to assist driving in Vehicle Ad hoc networks (VANETs) circumstances. In the proposed scheme, vehicles' current speed and space headway are obtained by Vehicle-to-Roadside unit (V2R) communication and Vehicle-to-Vehicle (V2V) communication. Based on the vehicles' current speed and adjacent vehicles' space headway, a recommended speed is calculated by on-board units installed in the vehicles, and then this recommended speed is provided to drivers. The drivers can change their speed to the recommended speed. At the recommended speed, vehicle travel efficiency can be improved: vehicles can arrive at destinations in a shorter travel time with fewer stop times, lower fuel consumption, and less CO2 emission. In particular, when approaching intersections, vehicles can pass through the intersections with less red light waiting time and a higher non-stop passing rate.

In this paper, we propose a novel multi-frame image denoising technique, which achieves the minimum variance of noise. Zero-mean and unknown variance white noise with an arbitrary distribution is considered in this paper. The proposed method consists of two parts. The first one is the estimation of the variance of noise for each image by considering the differences of all pairs of images. The second one is an actual denoising process in which the convex combination of all images with weight coefficients determined by the estimated variances is constructed. We also give an efficient algorithm by which we can obtain the same result by successive convex combinations. The efficacy of the proposed method is confirmed by computer simulations.

In the recently developed Flexible Wireless System (FWS), the same platform needs to deal with different wireless systems. This increases nonlinear distortion in its wideband power amplifier (PA) because the PA needs to concurrently amplify multi-band signals. By taking higher harmonics as well as inter- and cross-modulation distortion into consideration, we have developed a method to analytically evaluate the adjacent channel leakage power ratio (ACPR) and error vector magnitude (EVM) on the basis of the PA's nonlinear characteristics. We devise a novel method for modeling the PA amplifying dual-band signals. The method makes it possible to model it merely by performing a one-tone test, making use of the Volterra series expansion and the general Wiener model. We then use the Mehler formula to derive the closed-form expressions of the PA's output power spectral density (PSD), ACPR, and EVM. The derivations are based on the assumption that the transmitted signals are complex Gaussian distributed in orthogonal frequency division multiplexing (OFDM) transmission systems. We validate the method by comparing measurement and simulation results and confirm it can appropriately predict the ACPR and EVM performance of the nonlinear PA output with OFDM inputs. In short, the method enables correct modeling of a wideband PA that amplifies dual-band signals merely by conducting a one-tone test.

This paper presents a method of reducing excitation error in sidelobe canceller without increasing the resolution of the digital phase shifters and the digital attenuators. In general sidelobe canceller, the null direction is shifted because of the excitation error (quantization error and random error, etc.) and the suppression capability degrades. The proposed method can alleviate the influence of the excitation error by vector composition of some quantized excitation weights. Computer simulation results show that the output signal to interference and noise power ratio (SINR) using the proposed method can improve greatly in comparison with that using conventional quantized excitation weight.

Electromagnetic power transmission through two cyl-inder-penetrated circular apertures in parallel conducting planes is studied. The Weber transform and superposition principle are used to represent the scattered field. A set of simultaneous equations for the modal coefficients are constituted based on the mode-matching and boundary conditions. The whole integration path is slightly deformed into a new one below the positive real axis not to pass through the pole singularities encountered on the original path so that it is easily calculated by direct numerical quadrature. Computation shows the behaviors of power transmission in terms of aperture geometry and wavelength. The presented scheme is very amenable to numerical evaluations and useful for various electromagnetic scattering and antenna radiation analysis involved with singularity problems.

This paper describes a small size broadband fractional-N RF synthesizer for an RF test module with a high throughput and multiple resources installed in RF Automated Test Equipment (ATE) systems. The core device is the PLL-LSI composed of the 13-band asymmetrical tournament form voltage-controlled oscillators (VCOs) and the proposed 48-bit ΔΣ modulator with the infinite impulse response (IIR) filter. The single-loop PLL RF synthesizer is constructed in the form of systems in package (SiP) including the PLL-LSI and the active loop filter. The RF synthesizer SiP features a small size of 20mm × 20mm × 3mm, a high frequency resolution of smaller than 50µHz, and a phase noise of better than -110dBc/Hz at offset frequency of 1MHz across a frequency range of 100MHz to 13.4GHz. In addition, a frequency settling time of 150 µs that is faster than our conventional dual-loop PLL synthesizers using the discrete VCOs or the YIG-tuned oscillators (YTOs) is achieved. The synthesizer SiP significantly contributes to the realization of small size, high throughput RF test modules for RF ATEs.

Digital watermarking techniques have been used to assert the ownerships of digital images. The ownership information is embedded in an image as a watermark so that the owner of the image can be identified. However, many types of attacks have been used in attempts to break or remove embedded watermarks. Therefore, the watermark should be very robust against various kinds of attacks. Among them, the print-and-scan (PS) attack is very challenging because it not only alters the pixel values but also changes the positions of the original pixels. In this paper, we propose a watermarking system operating in the discrete cosine transform (DCT) domain. The polarities of the DCT coefficients are modified for watermark embedding. This is done by considering the properties of DCT coefficients under the PS attack. The proposed system is able to maintain the image quality after watermarking and the embedded watermark is very robust against the PS attack as well.

On-chip transmission lines are widely used in ultrahigh-frequency integrated circuits. One of the issues in modeling such transmission lines is that no reference impedance can be established on a chip. Conventionally, the parallel admittance Yp has been adopted as a reference parameter for on-chip transmission lines instead of a reference characteristic impedance of 50Ω. In the case of CMOS processes, however, Yp can have complicated characteristics in the short-millimeter-wave band owing to the frequency characteristics of the electric permittivity of low-k materials, which cannot be expressed using a simple circuit. To solve this problem, we propose the use of the series impedance Zs as a reference parameter for transmission-line modeling since it basically can be determined from the geometrical dimensions and the frequency-stable permeability and resistivity. The parameters of transmission lines obtained by the proposed method were compared with those obtained by conventional methods using a 40nm CMOS process. By using the equivalent circuit model of Yp along with RLC resonators, it is shown that the peaks of the frequency characteristics of Yp can be used to explain the absorption spectrum of the dielectric. This suggests that the proposed method is suitable for CMOS short-millimeter-wave transmission lines.

A novel spatially modulated communication method, appropriate for wireless power transmission applications at 5.8GHz, is proposed using dual scatterers embedded with lumped elements. Analytical expression for the received wave in the spatial modulation is derived, and the characteristics are verified with simulation and measurement by varying the embedded capacitor. The maximum measured variation of the received voltage is more than 15dB and that of the phase is more than 270 degrees at 5.8GHz. The estimated amplitude modulation factor is more than 70%. Using the data obtained, we estimate the practical received waveforms modulated by the applied voltage to a varactor for the amplitude modulation scheme.

The classification of human motion is an important aspect of monitoring pedestrian traffic. This requires the development of advanced surveillance and monitoring systems. Methods to achieve this have been proposed using micro-Doppler radars. However, reliable long-term data and/or complicated procedures are needed to classify motion accurately with these conventional methods because their accuracy and real-time capabilities are invariably inadequate. This paper proposes an accurate and real-time method for classifying the movements of pedestrians using ultra wide-band (UWB) Doppler radar to overcome these problems. The classification of various movements is achieved by extracting feature parameters based on UWB Doppler radar images and their radial velocity distributions. Experiments were carried out assuming six types of pedestrian movements (pedestrians swinging both arms, swinging only one arm, swinging no arms, on crutches, pushing wheelchairs, and seated in wheelchairs). We found they could be classified using the proposed feature parameters and a k-nearest neighbor algorithm. A classification accuracy of 96% was achieved with a mean calculation time of 0.55s. Moreover, the classification accuracy was 99% using our proposed method for classifying three groups of pedestrian movements (normal walkers, those on crutches, and those in wheelchairs).

In this paper, we propose periodic and aperiodic security limits for compromising emanations in the VHF and UHF bands. First, we perform the electromagnetic emanation security (EMSEC)-channel measurements in the 200-1000MHz frequency bands. Second, we analyse the pathloss characteristics of the indoor EMSEC-channel based on these measurements. Through this EMSEC-channel analysis, we affirm that the total radio attenuation, which is one of the key parameters for determining the security limits for compromising emanations, follows the Rician distribution. With these results, we propose that periodic and aperiodic emission security limits can be classified into two levels depending on the total radio attenuation and the extent of required confidentiality. The proposed security limits are compared with other security limits and existing civil and military EMC standards.

An S-band GaN on Si based 1kW-class SSPA system for space wireless applications is proposed. Since high-efficiency and high-reliability amplifier is one of the most important technologies for power and communication systems in a future space base station on a planet, compact, high-power, and high-efficiency SSPA is strongly requested instead of TWTA. Thus, we adopt GaN on Si based amplifier due to its remarkable material properties. At the beginning, thermal vacuum and radiation test of GaN on Si are conducted so as to confirm the space applicability. Fabricated SSPA system consists of eight 200W HPAs and coaxial waveguide power combiner. It achieves high efficiency such as 57% of drain efficiency and 87% of combining efficiency when RF output power achieves more than 60dBm. Furthermore, long-term stable operation and good phase noise characteristics are also confirmed.

This paper presents the shadowing analysis of a body area network (BAN) diversity antenna based on the statistical measurements of the human walking motion. First, the dynamic characteristics of the arm-swing motion were measured using human subjects, and a statistical analysis was then carried out using the measured data to extract useful information for the analysis of a BAN diversity antenna. Second, the analytical results of the shadowing effects of the BAN antenna were shown based on the statistical data of the swing motion. The difference between the typical and the realistic arm-swinging models significantly affected the bit error rate (BER) characteristic of the BAN antenna. To eliminate the shadowing caused by the movement of the arms, a BAN diversity antenna was used. Particular emphasis was placed on the evaluation of the spatial separation of the diversity antennas to attain reduction of the signal-to-noise ratio (SNR) required to achieve a specific BER performance, considering the combined outcome of shadowing and multipath fading unique to BAN antenna systems. We determined that an antenna angle separation of greater than 80° is required to reduce the shadowing effects when the diversity antenna is mounted at the left waist in a symmetrical configuration. Further, an antenna angle separation of 120° is required when the diversity antenna is mounted in an asymmetric configuration.

To raise the energy efficiency of wireless clients, it is important to sleep in idle periods. When multiple network applications are running concurrently on a single wireless client, packets of each application are sent and received independently, but multiplexed at MAC-level. This uncoordinated behavior makes it difficult to control of sleep timing. In addition, frequent state transitions between active and sleep modes consume non-negligible energy. In this paper, we propose a transport-layer approach that resolves this problem and so reduces energy consumed by multiple TCP flows on a wireless LAN (WLAN) client. The proposed method, called SCTP tunneling, has two key features: flow aggregation and burst transmission. It aggregates multiple TCP flows into a single SCTP association between a wireless client and an access point to control packet transmission and reception timing. Furthermore, to improve the sleep efficiency, SCTP tunneling reduces the number of state transitions by handling multiple packets in a bursty fashion. In this study, we construct a mathematical model of the energy consumed by SCTP tunneling to assess its energy efficiency. Through numerical examples, we show that the proposed method can reduce energy consumption by up to 69%.

A Simple decoding method for short-range MIMO (SR-MIMO) transmission can reduce the power consumption for MIMO decoding, but the distance between the transceivers requires millimeter-order accuracy in order to satisfy the required transmission quality. In this paper, we propose a phase difference control method between each propagation channel to alleviate the requirements for the transmission distance accuracy. In the proposed method, the phase difference between each propagation channel is controlled by changing the transmission (or received) power ratio of each element of sub-array antennas. In millimeter-wave broadband transmission simulation, we clarified that when sub-array antenna spacing is set to 6.6 mm and element spacing of sub-array antenna is set to 2.48mm, the proposed method can extend the transmission distance range satisfying the required transmission quality, which is that bit error rate (BER) before error correction is less than 10-2 from 9∼29mm to 0∼50mm in QPSK, from 15∼19mm to 0∼30mm in 16QAM, and from only 15mm to 4∼22mm in 64QAM.

The linearity analysis of a passive mixer is presented. The distortion mechanism caused by switching operation of a MOS transistor is elucidated from the static and dynamic analysis of passive mixers. Furthermore, the maximum input and output level to keep linear operation and its required bias conditions are expressed by simple equations. The maximum linear output amplitude of the passive mixer is determined only by the local signal amplitude and it does not depend on input and output impedance. The calculated linearity performances agree well with simulated and measured results.