In this paper, we compare the performance of evolutionary digital filters (EDFs) for IIR adaptive digital filters (ADFs) in terms of convergence behavior and stability, and discuss their advantages. The authors have already proposed the EDF which is controlled by adaptive algorithm based on the evolutionary strategies of living things. This adaptive algorithm of the EDF controls and changes the coefficients of inner digital filters using the cloning method or the mating method. Thus, the adaptive algorithm of the EDF is of a non-gradient and multi-point search type. Numerical examples are given to demonstrate the effectiveness and features of the EDF such that (1) they can work as adaptive filters as expected, (2) they can adopt various error functions such as the mean square error, the absolute sum error, and the maximum error functions, and (3) the EDF using IIR filters (IIR-EDF) has a higher convergence rate and smaller adaptation noise than the LMS adaptive digital filter (LMS-ADF) and the adaptive digital filter based on the simple genetic algorithm (SGA-ADF) on a multiple-peak surface.

Penumbral imaging is a technique which uses the facts that spatial information can be recovered from the shadow or penumbra that an unknown source casts through a simple large circular aperture. The technique is based on a linear deconvolution. In this paper, a two-step method is proposed for decoding penumbral images. First a local-statistic filter based on adaptive windowing is applied to smooth the noise; then, followed by the conventional linear deconvolution. The simulation results show that the reconstructed image is dramatically improved in comparison to that without the noise-smoothing filtering, and the proposed method is also applied to real experimental X-ray imaging.

This paper describes the design and performance of a high-speed 6-bit ADC using SiGe HBT for measuring-instrument applications. We show that the Gummel-Poon model suffices for SiGe HBT modeling and then we describe that the folding/interpolation architecture as well as simple, differential circuit design are suitable for ADC design with SiGe HBT. Measured results show that the nonlinearity of the ADC is within 1/2 LSB, and the effective bits are 5. 2 bits at an input frequency of 100 MHz and 4. 2 bits at 200 MHz with 768 MS/s. We also describe some design issues for folding/interpolation ADC.

An image recognition system using NEURO4, a programmable parallel processor, is described. Optical flow is the velocity field that an observer detects on a two-dimensional image and gives useful information, such as edges, about moving objects. The processing time for detecting optical flow on the NEURO4 system was analyzed. Owing to the parallel computation scheme, the processing time on the NEURO4 system is proportional to the square root of the size of images, while conventional sequential computers need time in proportion to the size. This analysis was verified by experiments using the NEURO4 system. When the size of an image is 84 84, the NEURO4 system can detect optical flow in less than 10 seconds. In this case the NEURO4 system is 23 times faster than a workstation, Sparc Station 20 (SS20). The larger the size of images becomes, the faster the NEURO4 system can detect optical flow than conventional sequential computers like SS20. Furthermore, the paralleling effect increases in proportion to the number of connected NEURO4 chips by a ring expansion scheme. Therefore, the NEURO4 system is useful for developing moving image recognition algorithms which require a large amount of processing time.

An adaptive array has been proposed as a canceller for both inter-symbol interference (ISI) and co-channel interference (CCI). However, it has no path-diversity gain since it selects just one signal correlated to the reference signal. In this paper, a novel interference canceller having sufficient path-diversity gain is proposed. The canceller is characterized by the combined configuration of an adaptive array and an equalizer. In the proposed system, a pre-selecting adaptive array is installed first. By employing a specific training sequence and sampling timing at the receiver during the training period, the perfect correlation between the "desired signal" and "short delayed" is achieved. Therefore, the pre-selecting adaptive array can extract the desired and ISI signals simultaneously, and the cascaded adaptive equalizer can provide the path-diversity gain without degradation by interference. The proposed system achieves a simple configuration and robustness against both ISI and CCI with a sufficient path diversity gain. In computer simulations, average BER characteristics of the proposed system were evaluated in a quasi-static Rayleigh fading channel. The simulation results showed that the system can reduce both long-delayed ISI and CCI efficiently, and that the expected path diversity gain is obtained even with strong CCI. They also showed that the degradation is not so serious when the number of antenna elements is less than that of incoming signals.

Method schemas were proposed as a formal model of object-oriented languages. A method schema S is called consistent if, for each method invocation during the execution of S, a method definition to be bound to the invoked method name is uniquely determined. However, the consistency testing problem is known to be undecidable in general. This paper presents an algorithm which analyzes the consistency of a given method schema. The algorithm decides the consistency problem in polynomial time for monadic method schemas. We also provide an incremental algorithm for testing consistency after updates of a method schema.

We developed a glass ferrule fiber optic connector. During development, we also studied wear-resistant coating technology for preventing scratches on the surface of a glass ferrule. The method of coating was sputtering, and the material was alumina. We confirmed that a thin uniform coating could be formed on the ferrule surface to improve the durability of glass ferrule connectors.

In the multipath mobile channel, the received signal suffers from both the fluctuation in the received field intensity caused by fading and waveform distortion caused by the echo. Diversity reception using multiple spaced antennas is an effective method to compensate for fading, while echo cancellation with an adaptive array is good at compensating for waveform distortion. In this paper, an adaptive switching echo cancellation/diversity reception method to compensate for both waveform distortion and fading is proposed. The proposed switching reception monitors the impacts of channel conditions on received signal and then one of an echo canceller and a diversity receiver is selected accordingly to compensate the channel. The compensation performance of the proposed switching reception in terms of both average DUR (Desired to Undesired signal Ratio) and the probability of DUR below a threshold value is investigated with computer simulation. The results show that the adaptive switching echo cancellation/diversity reception has realized the advantages of both adaptive echo cancellation and diversity reception.

In this paper, we propose a transformation technique for the multiplications of one variable with multiple constants, which are frequently seen in the various applications of signal processing, image processing, and so forth. The method is based on the exploration of common subexpressions among constants and reduces the number of shifts, additions, and subtractions to implement linear computations with hardware. Our method searches for regularity among elements of a linear transform using matrix decomposition and generates a reduced data-flow graph which preserves the full regularity. We show experimental results obtained using Discrete Cosine Transform (DCT) and Fast Fourier Transform (FFT) and illustrate the effectiveness of the method.

This paper proposes a frequency diversity transmission scheme that obtains a frequency diversity gain and does not degrade spectrum efficiency; it utilizes multiple carrier frequencies alternately, not simultaneously. This scheme improves the bit error rate (BER) of significant information bits by sacrificing that of insignificant bits in fading channels. Simulation results show that the error floor of significant information bits is reduced to less than 1/5 while that of insignificant bits is doubled. They also show that the proposed scheme improves the received 4-bit ADPCM voice signal-to-noise ratio (SNR) by approximately 4 dB even when the frequency correlation is 0. 5.

VP Network Designer, a software tool that automates the tasks involved in the transaction of service orders in VP leased line services, is introduced here in this paper. The tool is composed of two functions: VP Design Explorer which, given a request for VP establishment, determines a disjoint backup and target VP routes to support fault tolerance under VP-APS scheme; Network Resource Administrator which provides data administering functions, useful in maintaining a clear insight into the state of the network. The paper focuses on the implementation of VP Design Explorer. A scheme, proposed as disjoint VP routes search, is used to evaluate a pair of VP routes that guarantee duct level independence. The scheme is based on an integer programming modeling approach, and is proved to be effective for evaluating disjoint paths in a hierarchical network. VP Design Explorer is equipped with an additional feature where, under conditions of resource shortage, it presents a set of additional resources that are necessary to satisfy VP demand, together with the VP routes that become possible by the additions. Formulation of the problem is attained through an extension of the disjoint VP routes search scheme. A prototype of VP Network Designer is presented and its performance tested using computer simulations. The tool is found to achieve a computational time performance in the order of seconds and minutes, for evaluating disjoint VP routes search problems under real life ATM network conditions.

In this paper, a new variable length code transmission technique utilizing multicode DS/SS is proposed. A common problem associated with the use of variable length codes over wireless channels is loss of synchronization due to bit inversion caused by channel noise. The loss of synchronization produces burst errors in the received source symbols. The proposed system assigns multiple spreading codes to a single user to transmit variable length codes. The number of the spreading codes is equal to the maximum bit length of the codewords. All the bits of the codeword are spread and transmitted at one time by utilizing the assigned multiple spreading codes. Therefore no synchronization of the codeword is required. This paper evaluates the performance of the proposed technique over an AWGN channel and a Rayleigh fading channel. Our results show that the proposed technique improves the symbol error rate (SER) performance by 2-3 dB on the AWGN channel and 10-20 dB on the Rayleigh fading channel as compared with a conventional transmission technique. The source-channel coding suitable for the proposed technique improves the performance by another 15 dB on the Rayleigh fading channel. The proposed transmission technique works even in a low Es/No region.

The tape deformation due to such particles as wear debris and dust in the head/tape contact region is one of the main causes of the signal quality deterioration in magnetic tape devices. Thus it is significant to make clear the tape deformation due to a particle for realizing higher recording densities. This paper investigates the tape deformation profile generated by a particle through an interferometric experiment and a simulation using a point loaded tape model. A rather good agreement between them is obtained, thereby the simulation is verified appropriate to estimate the tape deformation due to a particle. This paper also describes the relationship between the spacing loss and the particle height, considering the tape deformation profile obtained from the simulation. In addition, the influence of the particle height on the width of the tape deformed area is estimated, which can make a basis of the design of error correction code.

Arc and contact resistance characteristics of Ag and Pd contacts were determined in several kinds of dielectric liquids, such as distilled water, methanol and n-hexane, under the inductive load condition. The experimental results showed that arc discharge types are dependent on dielectric liquids. A steady arc develops in air under this test condition. However, it was found that not the steady arc but the showering arc occurs in distilled water and methanol at a low load current. It was demonstrated that this phenomenon is caused by the high capacitance generated by the ambient dielectric liquid. Also, in almost all cases, the contact resistance behavior in dielectric liquids is satisfactory because metal spots remain on the contact surface. However, in n-hexane, the contact resistance tends to deteriorate, particularly for the Ag contact, with increasing load current. It seems that the deterioration of contact resistance is caused by carbon included in n-hexane.

Effects of organic gases (1, 4-butanediol, n-hexane, phenol, and benzene) on the contact resistance (the electrical life and the mechanical life) and the sticking were evaluated. These effects were evaluated by using telecommunication relays from which the cases were removed. Contact materials were Au90Ag10(clad)/Ag40Pd60 (base). Test conditions were as follows: In the cases of the electrical life test and the mechanical life test: Load conditions: DC28 V, 100 mA and 0 V, 0 mA. Temperature: 85. Frequency: 5 Hz. Number of operations: 2,500,000 times. In the case of the sticking test: Load condition: DC96 V, 140 mA. Temperature: 50. Frequency: 5 Hz. Number of operations: 2,000,000 times. It was found that the electrical life was more than 2,500,000 times, the mechanical life was more than 2,500,000 times, and the sticking didnt occur in the case of 1, 4-butanediol. The electrical life was improved by adding 1, 4-butanediol to phenol and benzene, respectively.

Gold on connector contacts is superior in environmental resistance. However, pores existing gold film are source to trigger the corrosion reaction between gold and base metal. For examination of the contacts, it has been popular to apply "Salt Spray Test" and "Sulfur Dioxide Test. " There are some differences of the corrosion products between two tests. Main metal forming the product in Salt Spray is Copper, and main metal in Sulfur Dioxide is Nickel. To investigate the reason, we tried to employ an electro-chemical method. As a result, it was found that there was the difference between the respective galvanic cell combinations generated through pores.

The alloy of Ag (40wt%)-Pd(60wt%) has been used in the electrical contacts of electromechanical devices due to its superior contact properties. There is currently, an increasing trend to decrease the size of electromechanical devices. However, it has been difficult to obtain a high contact force and the high restoring force of contacts, and these problems cause contact failures such as high contact resistance. In response to this problem, the alloy is overlaid with an Au layer which is not affected by oxide films. However, when the contacts are subjected to an unacceptable amount of mechanical shock, adhesion of the Au overlay occurs easily. In order to solve these difficulties, it can be proposed to cover the contact surface with high electric conductive oxide films. With this concept, the Au overlay should be unnecessary. In the present study, to reduce the high contact resistance of the Ag-Pd alloy contaminated with an oxide film, very small amounts of Mg and Cr were used in separate doping trials to the alloy. The improvement of contact resistance characteristics is the focus of the present study. Specimens of Ag (40wt%)-Pd(60wt%), Ag-Pd-Mg(0.1, 0.5 and 1.0wt%), and Ag-Pd-Cr(0.1 and 0.5wt%) were oxidized at elevated temperatures to accelerate the process of oxidation, and the growth kinetic law of oxide films grown on the surfaces were evaluated by ellipsometry. The effect of the oxide film on the contact resistance characteristics were then clarified. A marked improvement of the contact resistance caused by the oxide film was found for the Ag-Pd alloy with a Mg doping agent. However, for the Cr doping agent, a low contact resistance was not obtained as same as the Ag-Pd alloy itself.

On account of its superior electrical contact performance, Ag (40wt%)-Pd(60wt%) alloy has been widely used to the electrical contacts of electromechanical devices. However, regarding small devices, some important difficulties arise due to the small size such as the degradation of the contact resistance caused by the oxide film grown on the surface. To solve these problems, it was reported previously that doping Mg and Cr into the Ag-Pd alloy was tried to improve the oxide film. As a result, the oxide film grown on the Ag-Pd-Mg surface exhibited a remarkably low contact resistance. However, for the oxide film on Ag-Pd-Cr, no improvement of the contact resistance was observed. In this study, to clarify the cause of the low contact resistance for Ag-Pd-Mg, the effect of the doping with a third element on the composition and formation of the oxide film was analyzed using electron diffractometry, XPS and STM. As a result, Ag was found to be distributed on the outermost surface and inside the oxide film formed on Ag-Pd-Mg. However, Ag was not found on the surface of and inside the oxide film formed on Ag-Pd-Cr. Therefore, it was concluded that the presence of Ag on the surface of and inside the oxide film reduces the resistivity of the film.

A method has been developed for evaluating the wear durability and adhesion characteristics of ultrathin overcoat films. The relationship between the wear depth and applied load or between the wear depth and number of scanning-scratch cycles is used in AFM nanowear tests. Inherent wear durability, which is independent of adhesion or substrate hardness, can be evaluated from the relationship between wear depth and applied load at relatively low loads, and the adhesion characteristics can be evaluated from the relationship at relatively high loads. Wear durability can be evaluated with a small number of scanning-scratch cycles and adhesion with a large number of cycles.

An acoustic diagnosis technique for the blower by wavelet transform and neural networks is described. It is important for this diagnosis to detect surging phenomena, which lead to the destruction of the blower. Dyadic wavelet transform is used as the pre-processing method. A multi-layered neural network is used as the discrimination method. Experiment is performed for a blower. The results show that the neural network with wavelet transform can detect surging sound well.