Shigetaka KUMASHIRO Hironori SAKAMOTO Kiyoshi TAKEUCHI
This paper reports the evaluation results of the channel boron distribution in the deep sub-0.1 [µm] n-MOSFETs for the first time. It has been found that the boron depletion effect becomes dominant and the reverse short channel effect becomes less significant in the deep sub-0.1 [µm] n-MOSFETs. It has been also found that the sheet charge distribution responsible for the reverse short channel effect is localized within a distance of 100 [nm] from the source/drain-extension junction.
In this paper, a novel variable-rate vector quantizer (VQ) design algorithm using fuzzy clustering technique is presented. The algorithm, termed fuzzy entropy-constrained VQ (FECVQ) design algorithm, has a better rate-distortion performance than that of the usual entropy-constrained VQ (ECVQ) algorithm for variable-rate VQ design. When performing the fuzzy clustering, the FECVQ algorithm considers both the usual squared-distance measure, and the length of channel index associated with each codeword so that the average rate of the VQ can be controlled. In addition, the membership function for achieving the optimal clustering for the design of FECVQ are derived. Simulation results demonstrate that the FECVQ can be an effective alternative for the design of variable-rate VQs.
Sanghyun JOO Hisakazu KIKUCHI Shigenobu SASAKI Jaeho SHIN
We introduce an extended EZW coder that uses flexible zerotree coding of wavelet coefficients. A flexible parent-child relationship is defined so as to exploit spatial dependencies within a subband as well as hierarchical dependencies among multi-scale subbands. The new relationship is based on a particular statistics that a large coefficient is more likely to have large coefficients in its neighborhood in terms of space and scale. In the flexible relationship, a parent coefficient in a subband relates to four child coefficients in the next finer subband in the same orientation. If each of the children is larger than a given threshold, the parent extends its parentship to the neighbors close to its conventional children. A probing bit is introduced to indicate whether a significant parent has significant children to be scanned. This enables us to avoid excessive scan of insignificant coefficients. Also, produced symbols are re-symbolized into simple variable-length binary codes to remove some redundancy according to a pre-defined rule. As a result, the wavelet coefficients can be described with a small number of binary symbols. This binary symbol stream gives a competitive performance without an additional entropy coding and thus a fast encoding/decoding is possible. Moreover, the binary symbols can be more compressed by an adaptive arithmetic coding. Our experimental results are given in both binary-coded mode and arithmetic-coded mode. Also, these results are compared with those of the EZW coder.
Christoph JUNGEMANN Stefan KEITH Martin BARTELS Bernd MEINERZHAGEN
The full-band Monte Carlo technique is currently the most accurate device simulation method, but its usefulness is limited because it is very CPU intensive. This work describes efficient algorithms in detail, which raise the efficiency of the full-band Monte Carlo method to a level where it becomes applicable in the device design process beyond exemplary simulations. The k-space is discretized with a nonuniform tetrahedral grid, which minimizes the discretization error of the linear energy interpolation and memory requirements. A consistent discretization of the inverse mass tensor is utilized to formulate efficient transport parameter estimators. Particle scattering is modeled in such a way that a very fast rejection technique can be used for the generation of the final state eliminating the main cause of the inefficiency of full-band Monte Carlo simulations. The developed full-band Monte Carlo simulator is highly efficient. For example, in conjunction with the nonself-consistent simulation technique CPU times of a few CPU minutes per bias point are achieved for substrate current calculations. Self-consistent calculations of the drain current of a 60nm-NMOSFET take about a few CPU hours demonstrating the feasibility of full-band Monte Carlo simulations.
Scott T. DUNHAM Alp H. GENCER Srinivasan CHAKRAVARTHI
Recent years have seen great advances in our understanding and modeling of the coupled diffusion of dopants and defects in silicon during integrated circuit fabrication processes. However, the ever-progressing shrinkage of device dimensions and tolerances leads to new problems and a need for even better models. In this review, we address some of the advances in the understanding of defect-mediated diffusion, focusing on the equations and parameters appropriate for modeling of dopant diffusion in submicron structures.
Future cellular systems are envisioned to support mixed traffic, and ultimately multimedia services. However, a mixture of voice and data requires novel service mechanisms that can guarantee quality of service. In order to transfer high-speed data, multislot channel allocation is seen as a favoured solution to the present systems with the least compromise to circuit- switched services. This paper evaluates the performance of narrowband voice calls and multislot data packet transmission in such integrated systems by using a matrix-analytic approach. This method achieves quadratic convergence compared to the conventional spectral methods. Mobility is also considered in a prioritized cellular environment where frequent handoff has the potential of degrading data performance. The voice call distribution, data packets throughput, delay and waiting time distribution are derived. Moreover, a new multiple priority-based distributed control algorithm and a voice rate control scheme are enforced to mitigate the queuing congestion of data packets. The numerical results derived from this study show that larger data packets incur longer latency and the use of these flexible schemes can improve the overall performance.
Masato FUJINAGO Tatsuya KUNIKIYO Tetsuya UCHIDA Eiji TSUKUDA Kenichiro SONODA Katsumi EIKYU Kiyoshi ISHIKAWA Tadashi NISHIMURA Satoru KAWAZU
We have developed a practical 3-D integrated process simulator (3-D MIPS) based on the orthogonal grid. 3-D MIPS has a 3-D topography simulator (3-D MULSS) and 3-D impurity simulator which simulates the processes of ion implantation, impurity diffusion and oxidation. In particular, its diffusion and segregation model is new and practical. It assumes the continuity of impurity concentration at the material boundary in order to coordinate with the topography simulator (3-D MULSS) with cells in which two or more kinds of materials exist. And then, we introduced a time-step control method using the Dufort-Frankel method of diffusion analysis for stable calculation, and a selective oxidation model to apply to more general structures than LOCOS structure. After that, the 3-D MIPS diffusion model is evaluated compared with experimental data. Finally, the 3-D MIPS is applied to 3-D simulations of the nMOS Tr. structure with LOCOS isolation, wiring interconnect and pn-junction capacitances, and DRAM storage node area.
This paper outlines the modeling requirements of integrated circuit (IC) fabrication processes that have lead to and sustained the development of computer-aided design of technology (i. e. TCAD). Over a period spanning more than two decades the importance of TCAD modeling and the complexity of required models has grown steadily. The paper also illustrates typical applications where TCAD has been powerful and strategic to IC scaling of processes. Finally, the future issues of atomic-scale modeling and the need for an hierarchical approach to capture and use such detailed information at higher levels of simulation are discussed.
Kyung-Koo HAN Kiyotoshi YASUMOTO
Radio waves propagating through tunnels are strongly attenuated in the presence of discontinuities such as bends and branches. The useful structural modifications are requested to get better circumstances for radio waves in tunnels. In this paper, we propose several modifications arranged in a conventional T-junction of two-dimensional tunnels and analyze the transmission characteristics of radio waves by using the finite volume time domain (FVTD) method.
Tetsutaro KOBAYASHI Hikaru MORITA
Speeding up modular inversion is one of the most important subjects in the field of information security. Over the elliptic curve -- on the prime finite field in particular goals -- public-key cryptosystems and digital signature schemes frequently use modular inversion if affine coordinates are selected. In the regular computer environment, most data transmission via networks and data storage on memories as well as the operation set of processors are performed in multiples of eight bits or bytes. A fast modular multiplication algorithm that matches these operation units for DSP was proposed to accelerate the Montgomery method by Dusse and Kaliski. However, modular inversion algorithms were developed using bit by bit operation and so do not match the operation unit. This paper proposes two techniques for modular inversion that suits any arbitrary processing unit. The first technique proposes a new extended GCD procedure without any division. It can be constructed by the shifting, adding and multiplying operations, all of which a Montgomery modular arithmetic algorithm employs. The second technique can reduce the delay time of post processing in the modular inversion algorithm. In particular, it is of great use for the modular inversion defined in the Montgomery representation. These proposed techniques make modular inversion about 5. 5 times faster.
Hafiz Md. HASAN BABU Tsutomu SASAO
This paper considers methods to design multiple-output networks based on decision diagrams (DDs). TDM (time-division multiplexing) systems transmit several signals on a single line. These methods reduce: 1) hardware; 2) logic levels; and 3) pins. In the TDM realizations, we consider three types of DDs: shared binary decision digrams (SBDDs), shared multiple-valued decision diagrams (SMDDs), and shared multi-terminal multiple-valued decision diagrams (SMTMDDs). In the network, each non-terminal node of a DD is realized by a multiplexer (MUX). We propose heuristic algorithms to derive SMTMDDs from SBDDs. We compare the number of non-terminal nodes in SBDDs, SMDDs, and SMTMDDs. For nrm n, log n, and for many other benchmark functions, SMTMDD-based realizations are more economical than other ones, where nrm n is a (2n)-input (n1)-output function computing (X2+Y2)+0.5, log n is an n-input n-output function computing (2n1)log(x1)/nlog2, and a denotes the largest integer not greater than a.
Hiroshi TSURUMI Miyuki SOEYA Hiroshi YOSHIDA Takafumi YAMAJI Hiroshi TANIMOTO Yasuo SUZUKI
The architecture and control procedure for a direct conversion receiver are investigated for a linear modulation scheme. The proposed design techniques maintain receiver linearity despite various types of signal distortion. The techniques include the fast gain control procedure for receiving a control channel for air interface connection, DC offset canceling in both analog and digital stages, and 2nd-order intermodulation distortion canceling in an analog down-conversion stage. Experimental and computer simulation results on PHS (Personal Handy-phone System) parameters, showed that required linear modulation performance was achieved and thus the applicability of the proposed techniques was demonstrated.
Masaki NAKANISHI Kiyoharu HAMAGUCHI Toshinobu KASHIWABARA
A binary moment diagram, which was proposed for arithmetic circuit verification, is a directed acyclic graph representing a function from binary-vectors to integers (f : {0,1}n Z). A multiplicative binary moment diagram is an extension of a binary moment diagram with edge weights attached. A multiplicative binary moment diagram can represent addition, multiplication and many other functions with polynomial numbers of vertices. Lower bounds for division, however, had not been investigated. In this paper, we show an exponential lower bound on the number of vertices of a multiplicative binary moment diagram representing a quotient function or a remainder function.
Hiroshi IKEMATSU Ken'ichi TAJIMA Kenji KAWAKAMI Kenji ITOH Yoji ISOTA Osami ISHIDA
This paper describes the distortion characteristics of an even harmonic type direct converter (EH-DC) used in earth stations for CDMA satellite communications. Direct conversion technique is known as a method to simplify circuit topologies of microwave transceivers. In satellite communications, multi carriers which have high and nearly equal level are provided to a quadrature mixer of the EH-DC. Hence, the third-order intermodulation degrades receiving characteristics. In this paper, we show the relationship between the distortion characteristics and noise figure of the EH-DC for CDMA satellite communication systems. Furthermore, we show NPR of even harmonic quadrature mixers caused by the third-order intermodulation. Experimental results in X-band indicate that the proposed EH-DC has almost the same BER characteristics compared with a heterodyne type transceiver.
A variable partition duplex scheme on packet reservation multiple access protocol (VPD-PRMA) is analyzed in this paper. We assume a four-state speech model for a conversational pair and successfully obtain performance measures by approximate Markovian analysis. Analytical results show that they quite fit simulation results; and VPD-PRMA can get higher statistical multiplexing gain than fixed partition duplex (FPD)-PRMA, due to the trunking effect. We further investigate the effect of design parameters of permission probability and enlarged reservation duration on system performance by computer simulation. Simulation results shows that it exists appropriate values for these two design parameters so that the packet dropping probability can be minimized. The adjustment of permission probability can greatly improve the performance of uplink traffic with slight deterioration of the performance of downlink traffic; the provision of enlarged reservation duration scheme can enhance the system performance.
Takahiro HOZUMI Osamu KAKUSHO Yutaka HATA
This paper shows the best operators for sum-of-products expressions. We first describe conditions of functions for product and sum operations. We examine all two-variable functions and select those that meet the conditions and then evaluate the number of product terms needed in the minimum sum-of-products expressions when each combination of selected product and sum functions is used. As a result of this, we obtain three product functions and nine sum functions on three-valued logic. We show that each of three product functions can express the same functions and MODSUM function is the most suitable for reduction of product terms. Moreover, we show that similar results are obtained on four-valued logic.
Toshihiro MATSUDA Naoko MATSUYAMA Kiyomi HOSOI Etsumasa KAMEDA Takashi OHZONE
Profiles of photoemission induced by hot electrons in LDD-type n-MOSFETs with L = 0.35-2.0 µm were measured with a photoemission microscope, which had a capability of 1000 magnification and a spatial resolution of 27 nm/pixel on a CCD imager sufficient to detect profile changes in the channel length direction. Under the bias condition of maximum substrate current, photoemission peaks were located at the LDD-drain edge and the n+-drain edge for the devices with L = 0.35 and L 0.40 µm, respectively. A peak position, only in the case of the 0.35 µm device, shifted toward the drain side by about 80 nm at VD = 7.0 V. Since VD did not affect peak positions in L 0.40 µm devices, the photoemission mechanisms may be different between L = 0.35 µm and L 0.40 µm devices. The photoemission points due to p-n junction breakdown were located at the cylindrical curvature edge of the n+-drain region. Two-dimensional device simulation, even when the lateral electric field, electron temperature and radiative recombination rate were taken into account, could not explain the experimental results completely.
Kiminobu NISHIMURA Mitsuo OHTA
Under a contamination of background sound noises, it seems difficult especially in a real working situation to evaluate various type statistics of only an objective sound signal fluctuation. In many cases of the noise evaluation, some signal processing method have been employed to eliminate the effect of background sound noises by first measuring emitted sound levels. In this study, a new evaluation method of sound level fluctuation is proposed in principle on the basis of the measurement of heterogeneous physical quantity other than sound pressures or sound levels to eliminate the effect of background sound noises. Though the theoretical analysis on acoustical emission caused by a mechanical vibration seems very difficult in a working situation, the sound noise fluctuation emitted only from an objective sound source can be effectively evaluated through its related vibration measurement by employing a fairly unified stochastic method proposed on the basis of a generalized regression analysis between sound and vibration. Here, the regression coefficients are determined by employing the least squares error method to minimize the mean square of estimation error to illustrate well the sound data by means of vibration data. Finally, the effectiveness of proposed method has been experimentally applied to the sound noise evaluation of a jigsaw.
A novel method to enhance the practical security of interferometric quantum cryptography is proposed, giving the protocol and detailed constructions including a controlled spontaneous photon emitter, a superradiance amplifier, beam splitters, phase shifters, and a pair of Mach-Zehnder interferometers. The intrinsic uncertainty due to the random phase selection out of three, leads to the detection of eavesdropping. The physical uncertainty of the controlled spontaneous emission of coherent photons also adds temporal equivocation to confuse eavesdroppers.
Masahiro KURODA Ryoji ONO Yoshiki SHIMOTSUMA Takashi WATANABE Tadanori MIZUNO
The optimistic consistency scheme has been established with respect to data consistency and availability in distributed systems. The nomadic data consistency model using version vectors to support data versioning for data synchronization and concurrent conflict detection is suitable for an optimistic replication system that supports large-scale wireless networks. This paper describes the architecture and its data consistency model using data versioning and its access domain control targeted for nomadic data sharing systems, such as collaborative works using database and messaging, and the data transfer optimizations of the model. We evaluate our data versioning scheme comparing with a traditional data versioning and the data transfer optimization by estimation and measurement assuming a mobile worker's job. We generate arithmetic formulas for data transfer estimation using the optimizing techniques and apply them to large-scale data sharing configurations in which collaboration groups are dynamically formed and data is exchanged in each group. The data versioning with an access domain increases flexibility in data sharing configurations, such as mobile collaboration systems and client/server type mobile systems. We confirmed that the combination of the general optimizations and the access domain configurations based on our data consistency model is applicable for large-scale mobile data sharing systems.