The transfer distance of the wireless power transfer (WPT) system with relay coil is longer, so this technology have a better practical perspective. But the location of the relay coil has a great impact on the transmission efficiency of the WPT system, and it is not easy to analyze. In order to research the influence law of the relay coil location on the transmission efficiency and obtain the optimal location, the paper firstly proposes the concept of relay coil location factor. And based on the location factor, a novel method for studying the influence of the relay coil location on the transmission efficiency is proposed. First, the mathematical model between the transmission efficiency and the location factor is built. Next, considering the transfer distance, coil radius, coil turns and load resistance, a lot of simulations are carried out to analyze the influence of the location factor on the transmission efficiency, respectively. The influence law and the optimal location factor were obtained with different parameters. Finally, a WPT system with relay coil was built for experiments. And the experiment results verify that the theoretical analysis is correct and the proposed method can simplify the analysis progress of the influence of relay coil location on the transmission efficiency. Moreover, the proposed method and the research conclusions can provide guidance for designing the multiple coils structure WPT system.

High power dissipation during scan test often causes undue yield loss, especially for low-power circuits. One major reason is that the resulting IR-drop in shift mode may corrupt test data. A common approach to solving this problem is partial-shift, in which multiple scan chains are formed and only one group of scan chains is shifted at a time. However, existing partial-shift based methods suffer from two major problems: (1) their IR-drop estimation is not accurate enough or computationally too expensive to be done for each shift cycle; (2) partial-shift is hence applied to all shift cycles, resulting in long test time. This paper addresses these two problems with a novel IR-drop-aware scan shift method, featuring: (1) Cycle-based IR-Drop Estimation (CIDE) supported by a GPU-accelerated dynamic power simulator to quickly find potential shift cycles with excessive peak IR-drop; (2) a scan shift scheduling method that generates a scan chain grouping targeted for each considered shift cycle to reduce the impact on test time. Experiments on ITC'99 benchmark circuits show that: (1) the CIDE is computationally feasible; (2) the proposed scan shift schedule can achieve a global peak IR-drop reduction of up to 47%. Its scheduling efficiency is 58.4% higher than that of an existing typical method on average, which means our method has less test time.

Omni-directional images have been used in wide range of applications including virtual/augmented realities, self-driving cars, robotics simulators, and surveillance systems. For these applications, it would be useful to estimate saliency maps representing probability distributions of gazing points with a head-mounted display, to detect important regions in the omni-directional images. This paper proposes a novel saliency-map estimation model for the omni-directional images by extracting overlapping 2-dimensional (2D) plane images from omni-directional images at various directions and angles of view. While 2D saliency maps tend to have high probability at the center of images (center bias), the high-probability region appears at horizontal directions in omni-directional saliency maps when a head-mounted display is used (equator bias). Therefore, the 2D saliency model with a center-bias layer was fine-tuned with an omni-directional dataset by replacing the center-bias layer to an equator-bias layer conditioned on the elevation angle for the extraction of the 2D plane image. The limited availability of omni-directional images in saliency datasets can be compensated by using the well-established 2D saliency model pretrained by a large number of training images with the ground truth of 2D saliency maps. In addition, this paper proposes a multi-scale estimation method by extracting 2D images in multiple angles of view to detect objects of various sizes with variable receptive fields. The saliency maps estimated from the multiple angles of view were integrated by using pixel-wise attention weights calculated in an integration layer for weighting the optimal scale to each object. The proposed method was evaluated using a publicly available dataset with evaluation metrics for omni-directional saliency maps. It was confirmed that the accuracy of the saliency maps was improved by the proposed method.

This letter is devoted to constructing new Type-II Z-complementary pairs (ZCPs). A ZCP of length N with ZCZ width Z is referred to in short by the designation (N, Z)-ZCP. Inspired by existing works of ZCPs, systematic constructions of (2N+3, N+2)-ZCPs and (4N+4, 7/2N+4)-ZCPs are proposed by appropriately inserting elements into concatenated GCPs. The odd-length binary Z-complementary pairs (OB-ZCPs) are Z-optimal. Furthermore, the proposed construction can generate even-length binary Z-complementary pairs (EB-ZCPs) with ZCZ ratio (i.e. ZCZ width over the sequence length) of 7/8. It turns out that the PMEPR of resultant EB-ZCPs are upper bounded by 4.

Technology for sixth-generation (6G) mobile communication system is now being widely studied. A sub-Terahertz band is expected to play a great role in 6G to enable extremely high data-rate transmission. This paper has two goals. (1) Introduction of 6G concept and propagation characteristics of sub-Terahertz-band radio waves. (2) Performance evaluation of intelligent reflecting surfaces (IRSs) based on beamforming in a sub-Terahertz band for smart radio environments (SREs). We briefly review research on SREs with reconfigurable intelligent surfaces (RISs), and describe requirements and key features of 6G with a sub-Terahertz band. After that, we explain propagation characteristics of sub-Terahertz band radio waves. Important feature is that the number of multipath components is small in a sub-Terahertz band in indoor office environments. This leads to an IRS control method based on beamforming because the number of radio waves out of the optimum beam is very small and power that is not used for transmission from the IRS to user equipment (UE) is little in the environments. We use beams generated by a Butler matrix or a DFT matrix. In simulations, we compare the received power at a UE with that of the upper bound value. Simulation results show that the proposed method reveals good performance in the sense that the received power is not so lower than the upper bound value.

This paper investigates a service deployment model for network function virtualization which handles per-flow priority to minimize the deployment cost. Service providers need to implement network services each of which consists of one or more virtual network functions (VNFs) with satisfying requirements of service delays. In our previous work, we studied the service deployment model with per-host priority; flows belonging to the same service, for the same VNF, and handled on the same host have the same priority. We formulated the model as an optimization problem, and developed a heuristic algorithm named FlexSize to solve it in practical time. In this paper, we address per-flow priority, in which flows of the same service, VNF, and host have different priorities. In addition, we expand FlexSize to handle per-flow priority. We evaluate per-flow and per-host priorities, and the numerical results show that per-flow priority reduces deployment cost compared with per-host priority.

This paper proposes a backup resource allocation model for virtual network functions (VNFs) to minimize the total allocated computing capacity for backup with considering the service delay. If failures occur to primary hosts, the VNFs in failed hosts are recovered by backup hosts whose allocation is pre-determined. We introduce probabilistic protection, where the probability that the protection by a backup host fails is limited within a given value; it allows backup resource sharing to reduce the total allocated computing capacity. The previous work does not consider the service delay constraint in the backup resource allocation problem. The proposed model considers that the probability that the service delay, which consists of networking delay between hosts and processing delay in each VNF, exceeds its threshold is constrained within a given value. We introduce a basic algorithm to solve our formulated delay-constraint optimization problem. In a problem with the size that cannot be solved within an acceptable computation time limit by the basic algorithm, we develop a simulated annealing algorithm incorporating Yen's algorithm to handle the delay constraint heuristically. We observe that both algorithms in the proposed model reduce the total allocated computing capacity by up to 56.3% compared to a baseline; the simulated annealing algorithm can get feasible solutions in problems where the basic algorithm cannot.

Nowadays, in various wireless sensor networks, both aperiodically generated packets like event detections and periodically generated ones for environmental, machinery, vital monitoring, etc. are transferred. Thus, packet loss caused by collision should be suppressed among aperiodic and periodic packets. In addition, some packets for wireless applications such as factory IoT must be transferred within permissible end-to-end delays, in addition to improving packet loss. In this paper, we propose transmission timing control of both aperiodic and periodic packets at an upper layer of medium access control (MAC). First, to suppress packet loss caused by collision, transmission timings of aperiodic and periodic packets are distributed on the time axis. Then, transmission timings of delay-bounded packets with permissible delays are assigned within the bounded periods so that transfer within their permissible delays is possible to maximally satisfy their permissible delays. Such control at an upper layer has advantages of no modification to the MAC layer standardized by IEEE 802.11, 802.15.4, etc. and low sensor node cost, whereas existing approaches at the MAC layer rely on MAC modifications and time synchronization among all sensor nodes. Performance evaluation verifies that the proposed transmission timing control improves packet loss rate regardless of the presence or absence of packet's periodicity and permissible delay, and restricts average transfer delay of delay-bounded packets within their permissible delays comparably to a greedy approach that transmits delay-bounded packets to the MAC layer immediately when they are generated at an upper layer.

We developed a self-controllable voltage level (SVL) circuit and applied this circuit to a single-power-supply, six-transistor complementary metal-oxide-semiconductor static random-access memory (SRAM) to not only improve both write and read performances but also to achieve low standby power and data retention (holding) capability. The SVL circuit comprises only three MOSFETs (i.e., pull-up, pull-down and bypass MOSFETs). The SVL circuit is able to adaptively generate both optimal memory cell voltages and word line voltages depending on which mode of operation (i.e., write, read or hold operation) was used. The write margin (VWM) and read margin (VRM) of the developed (dvlp) SRAM at a supply voltage (VDD) of 1V were 0.470 and 0.1923V, respectively. These values were 1.309 and 2.093 times VWM and VRM of the conventional (conv) SRAM, respectively. At a large threshold voltage (Vt) variability (=+6σ), the minimum power supply voltage (VMin) for the write operation of the conv SRAM was 0.37V, whereas it decreased to 0.22V for the dvlp SRAM. VMin for the read operation of the conv SRAM was 1.05V when the Vt variability (=-6σ) was large, but the dvlp SRAM lowered it to 0.41V. These results show that the SVL circuit expands the operating voltage range for both write and read operations to lower voltages. The dvlp SRAM reduces the standby power consumption (PST) while retaining data. The measured PST of the 2k-bit, 90-nm dvlp SRAM was only 0.957µW at VDD=1.0V, which was 9.46% of PST of the conv SRAM (10.12µW). The Si area overhead of the SVL circuits was only 1.383% of the dvlp SRAM.

Since the outbreak of IoT malware “Mirai,” several incidents have occurred in which IoT devices have been infected with malware. The malware targets IoT devices whose Telnet and SSH services are accessible from the Internet and whose ID/Password settings are not strong enough. Several IoT malware families, including Mirai, are also known that restrict access to Telnet and other services to keep the devices from being infected by other malware after infection. However, tens of thousands of devices in Japan can be still accessed Telnet services over the Internet according to network scan results. Does this imply that these devices can avoid malware infection by setting strong enough passwords, and thus cannot be used as a stepping stone for cyber attacks? In February 2019, we initiated the National Operation Toward IoT Clean Environment (NOTICE) project in Japan to investigate IoT devices with weak credentials and notify the device users. In this study, we analyze the results of the NOTICE project from February 2021 to May 2021 and the results of the large-scale darknet monitoring to reveal whether IoT devices with weak credentials are infected with malware or not. Moreover, we analyze the IoT devices with weak credentials to find out the factors that prevent these devices from being infected with malware and to assess the risk of abuse for cyber attacks. From the results of the analysis, it is discovered that approximately 2,000 devices can be easily logged in using weak credentials in one month in Japan. We also clarify that no device are infected with Mirai and its variants malware due to lack of functions used for malware infection excluding only one host. Finally, even the devices which are logged in by NOTICE project are not infected with Mirai, we find that at least 80% and 93% of the devices can execute arbitrary scripts and can send packets to arbitrary destinations respectively.

Wireless technology improvements have been continually increasing, resulting in greater needs for system design and implementation to accommodate all newly emerging standards. As a result, developing a system that ensures compatibility with numerous wireless systems has sparked interest. As a result of their flexibility and scalability over alternative wireless design options, software-defined radios (SDRs) are highly motivated for wireless device modelling. This research paper delves into the difficulties of designing a reconfigurable multi modulation baseband modulator for SDR systems that can handle a variety of wireless protocols. This research paper has proposed an area-efficient Reconfigurable Baseband Modulator (RBM) model to accomplish multi modulation scheme and resolve the adaptability and flexibility issues with the wide range of wireless standards. This also presents the feasibility of using a multi modulation baseband modulator to maximize adaptability with the least possible computational complexity overhead in the SDR system for next-generation wireless communication systems and provides parameterization. Finally, the re-configurability is evaluated concerning the appropriate symbols generations and analyzed its performance metrics through hardware synthesize results.

Modern large scale distributed storage systems play a central role in data center and cloud storage, while node failure in data center is common. The lost data in failure node must be recovered efficiently. Locally repairable codes (LRCs) are designed to solve this problem. The locality of an LRC is the number of nodes that participate in recovering the lost data from node failure, which characterizes the repair efficiency. An LRC is called optimal if its minimum distance attains Singleton-type upper bound [1]. In this paper, using basic techniques of linear algebra over finite field, infinite optimal LRCs over extension fields are derived from a given optimal LRC over base field(or small field). Next, this paper investigates the relation between near-MDS codes with some constraints and LRCs, further, proposes an algorithm to determine locality of dual of a given linear code. Finally, based on near-MDS codes and the proposed algorithm, those obtained optimal LRCs are shown.

In recent years, microwave wireless power transfer (WPT) has attracted considerable attention due to the increasing demand for various sensors and Internet of Things (IoT) applications. Microwave WPT requires technology that can detect and avoid human bodies in the transmission path. Using a phantom is essential for developing such technology in terms of standardization and human body protection from electromagnetic radiation. In this study, a simple and lightweight phantom was developed focusing on its radar cross-section (RCS) to evaluate human body avoidance technology for use in microwave WPT systems. The developed phantom's RCS is comparable to that of the human body.

The degree of reception of BS signals is affected by various factors. After routinely recording it at two observation points at two locations, we found that momentary upward and downward level shifts occurred multiple times, mainly during daytime. These level shifts were observed at one location. No such signal was sensed at the other location. After producing an algorithm to extract such momemtary level shifts, their statistical properties were investigated. Careful analyses, including assessment of the signal polarity, amplitude, duration, hours, and comparison with actual flight schedules and route information implied that these level shifts are attributable to the interference of direct and reflected waves from aircraft flying at approximately tropopause altitude. This assumption is further validated through computer simulations of BS signal interference.

In order to solve the problems of copyrights infringement, high cost and complex process of rights protection in current media convergence center, a digital rights management system based on blockchain technology and IPFS (Inter Planetary File System) technology is proposed. Considering that large files such as video and audio cannot be stored on the blockchain directly, IPFS technology is adopted as the data expansion scheme for the data storage layer of the Ethereum platform, IPFS protocol is further used for distributed data storage and transmission of media content. In addition, smart contract is also used to uniquely identify digital rights through NFT (Non-fungible Tokens), which provides the characteristics of digital rights transferability and traceability, and realizes an open, transparent, tamper-proof and traceable digital rights management system for media convergence center. Several experimental results show that it has higher transaction success rate, lower storage consumption and transaction confirmation delay than existing scheme.

This paper introduces a deep reinforcement learning approach to solve the virtual network function scheduling problem in dynamic scenarios. We formulate an integer linear programming model for the problem in static scenarios. In dynamic scenarios, we define the state, action, and reward to form the learning approach. The learning agents are applied with the asynchronous advantage actor-critic algorithm. We assign a master agent and several worker agents to each network function virtualization node in the problem. The worker agents work in parallel to help the master agent make decision. We compare the introduced approach with existing approaches by applying them in simulated environments. The existing approaches include three greedy approaches, a simulated annealing approach, and an integer linear programming approach. The numerical results show that the introduced deep reinforcement learning approach improves the performance by 6-27% in our examined cases.

Hardware oriented security and trust of semiconductor integrated circuit (IC) chips have been highly demanded. This paper outlines the requirements and recent developments in circuits and packaging systems of IC chips for security applications, with the particular emphasis on protections against physical implementation attacks. Power side channels are of undesired presence to crypto circuits once a crypto algorithm is implemented in Silicon, over power delivery networks (PDNs) on the frontside of a chip or even through the backside of a Si substrate, in the form of power voltage variation and electromagnetic wave emanation. Preventive measures have been exploited with circuit design and packaging technologies, and partly demonstrated with Si test vehicles.

We propose a radio-over-fiber (RoF) system with 1-bit outphasing modulation. The proposed RoF system does not require a power-hungry digital-to-analog converter in access points and relaxes the operation speed of optical transceivers to reduce device cost. We introduce two configurations to enable 1-bit outphasing modulation in our system; mixed-signal and all-digital configurations. In the mixed-signal configuration, the effects of harmonics and phase/amplitude mismatch on the adjacent channel leakage ratio (ACLR) were analyzed through simulation, and wideband transmission with a signal bandwidth of 400 MHz was experimentally verified, complying with the 3rd Generation Partnership Project (3GPP) standard for millimeter-wave band. Moreover, wide-band transmission with a signal bandwidth of 1 GHz was also experimentally verified for beyond-5G and 6G. The all-digital configuration can be implemented in a standard digital design flow. This configuration was also verified to comply with the 3GPP standard by properly selecting the intermediate and sampling frequencies to mitigate the effects of folded harmonics and quantization noise. Finally, the proposed RoF system with both configurations has been shown to have a higher bandwidth efficiency compared with other systems complying with the 3GPP standard for the ACLR. Therefore, the proposed RoF system provides a cost-effective in-building wireless solution for 5G and 6G mobile network systems.

Uncovered muck truck detection aims to detect the muck truck and distinguish whether it is covered or not by dust-proof net to trace the source of pollution. Unlike traditional detection problem, recalling all uncovered trucks is more important than accurate locating for pollution traceability. When two objects are very close in an image, the occluded object may not be recalled because the non-maximum suppression (NMS) algorithm can remove the overlapped proposal. To address this issue, we propose a Location First NMS method to match the ground truth boxes and predicted boxes by position rather than class identifier (ID) in the training stage. Firstly, a box matching method is introduced to re-assign the predicted box ID using the closest ground truth one, which can avoid object missing when the IoU of two proposals is greater than the threshold. Secondly, we design a loss function to adapt the proposed algorithm. Thirdly, a uncovered muck truck detection system is designed using the method in a real scene. Experiment results show the effectiveness of the proposed method.

We propose a non-photorealistic rendering method to automatically generate reaction-diffusion-pattern-like images from photographic images. The proposed method uses smoothing filter with a circular window, and changes the size of the circular window depending on the position in photographic images. By partially changing the size of the circular window, the size of reaction-diffusion patterns can be changed partially. To verify the effectiveness of the proposed method, experiments were conducted to apply the proposed method to various photographic images.