Hardware accelerators are designed to support a specialized processing dataflow for everchanging deep neural networks (DNNs) under various processing environments. This paper introduces two hardware properties to describe the cost of data movement in each memory hierarchy. Based on the hardware properties, this paper proposes a set of evaluation metrics that are able to evaluate the number of memory accesses and the required memory capacity according to the specialized processing dataflow. Proposed metrics are able to analytically predict energy, throughput, and area of a hardware design without detailed implementation. Once a processing dataflow and constraints of hardware resources are determined, the proposed evaluation metrics quickly quantify the expected hardware benefits, thereby reducing design time.

Embedded software often interacts with multiple inputs from various sensors whose dependency is often complex or partially known to developers. With incomplete information on dependency, testing is likely to be insufficient in detecting errors. We propose a method to enhance testing coverage of embedded software by identifying subtle and often neglected dependencies using information contained in usage log. Usage log, traditionally used primarily for investigative purpose following accidents, can also make useful contribution during testing of embedded software. Our approach relies on first individually developing behavioral model for each environmental input, performing compositional analysis while identifying feasible but untested dependencies from usage log, and generating additional test cases that correspond to untested or insufficiently tested dependencies. Experimental evaluation was performed on an Android application named Gravity Screen as well as an Arduino-based wearable glove app. Whereas conventional CTM-based testing technique achieved average branch coverage of 26% and 68% on these applications, respectively, proposed technique achieved 100% coverage in both.

As a mobile phone progresses with the third, fourth, and fifth generations, the frequency bands used in mobile phones are increasing dramatically. RF components for mobile phone terminals correspond to this increasing frequency band. In the case of power amplifier (PA), which is one of the RF components, it is necessary to correspond many frequency bands in one PA. In this case, the wideband of the matching circuit is a typical one of the technical problems of PA. In this study, we focus on two-stage and three-stage connections of LC ladder matching circuits widely applied in PA, and compare them from the viewpoint of broadband. In order to efficiently analyze multi-stage LC-matching circuits, the following two new methods were devised. First, we derived the analysis formula of LC and CL-matching circuits when the termination impedance was extended to a complex number. Second, we derived a condition in which the frequency derivative of the input impedance is zero.

With the rapid progress of the integrated nanophotonics technology, the optical neural network architecture has been widely investigated. Since the optical neural network can complete the inference processing just by propagating the optical signal in the network, it is expected more than one order of magnitude faster than the electronics-only implementation of artificial neural networks (ANN). In this paper, we first propose an optical vector-matrix multiplication (VMM) circuit using wavelength division multiplexing, which enables inference processing at the speed of light with ultra-wideband. This paper next proposes optoelectronic circuit implementation for batch normalization and activation function, which significantly improves the accuracy of the inference processing without sacrificing the speed performance. Finally, using a virtual environment for machine learning and an optoelectronic circuit simulator, we demonstrate the ultra-fast and accurate operation of the optical-electronic ANN circuit.

Optical logic circuits based on integrated nanophotonics attract significant interest due to their ultra-high-speed operation. However, the power dissipation of conventional optical logic circuits is exponential to the number of inputs of target logic functions. This paper proposes a synthesis method reducing power dissipation to a polynomial order of the number of inputs while exploiting the high-speed nature. Our method divides the target logic function into multiple sub-functions with Optical-to-Electrical (OE) converters. Each sub-function has a smaller number of inputs than that of the original function, which enables to exponentially reduce the power dissipated by an optical logic circuit representing the sub-function. The proposed synthesis method can mitigate the OE converter delay overhead by parallelizing sub-functions. We apply the proposed synthesis method to the ISCAS'85 benchmark circuits. The power consumption of the conventional circuits based on the Binary Decision Diagram (BDD) is at least three orders of magnitude larger than that of the optical logic circuits synthesized by the proposed method. The proposed method reduces the power consumption to about 100mW. The delay of almost all the circuits synthesized by the proposed method is kept less than four times the delay of the conventional BDD-based circuit.

This paper investigates an adaptive notch digital filter that employs normal state-space realization of a single-frequency second-order IIR notch digital filter. An adaptive algorithm is developed to minimize the mean-squared output error of the filter iteratively. This algorithm is based on a simplified form of the gradient-decent method. Stability and frequency estimation bias are analyzed for the adaptive iterative algorithm. Finally, a numerical example is presented to demonstrate the validity and effectiveness of the proposed adaptive notch digital filter and the frequency-estimation bias analyzed for the adaptive iterative algorithm.

In unlicensed spectrum, wireless communications employing carrier sense multiple access with collision avoidance (CSMA/CA) suffer from longer transmission delay time as the number of user terminals (UTs) increases, because packet collisions are more likely to occur. To cope with this problem, this paper proposes a new multiuser detection (MUD) scheme that uses both request-to-send (RTS) and enhanced clear-to-send (eCTS) for high-reliable and low-latency wireless communications. As in conventional MUD scheme, the metric-combining MUD (MC-MUD) calculates log likelihood functions called metrics and accumulates the metrics for the maximum likelihood detection (MLD). To avoid increasing the number of states for MLD, MC-MUD forces the relevant UTs to retransmit their packets until all the collided packets are correctly detected, which requires a kind of central control and reduces the system throughput. To overcome these drawbacks, the proposed scheme, which is referred to as cancelling MC-MUD (CMC-MUD), deletes replicas of some of the collided packets from the received signals, once the packets are correctly detected during the retransmission. This cancellation enables new UTs to transmit their packets and then performs MLD without increasing the number of states, which improves the system throughput without increasing the complexity. In addition, the proposed scheme adopts RTS and eCTS. One UT that suffers from packet collision transmits RTS before the retransmission. Then, the corresponding access point (AP) transmits eCTS including addresses of the other UTs, which have experienced the same packet collision. To reproduce the same packet collision, these other UTs transmit their packets once they receive the eCTS. Computer simulations under one AP conditions evaluate an average carrier-to-interference ratio (CIR) range in which the proposed scheme is effective, and clarify that the transmission delay time of the proposed scheme is shorter than that of the conventional schemes. In two APs environments that can cause the hidden terminal problem, it is demonstrated that the proposed scheme achieves shorter transmission delay times than the conventional scheme with RTS and conventional CTS.

We propose an algorithm for the constrained design of FIR filters with sparse coefficients. In general filter design approaches, as the length of the filter increases, the number of multipliers used to construct the filter increases. This is a serious problem, especially in two-dimensional FIR filter designs. The FIR filter coefficients designed by the least-squares method with peak error constraint are optimal in the sense of least-squares within a given order, but not necessarily optimal in terms of constructing a filter that meets the design specification under the constraints on the number of coefficients. That is, a higher-order filter with several zero coefficients can construct a filter that meets the specification with a smaller number of multipliers. We propose a two-step approach to design constrained sparse FIR filters. Our method minimizes the number of non-zero coefficients while the frequency response of the filter that meets the design specification. It achieves better performance in terms of peak error than conventional constrained least-squares designs with the same or higher number of multipliers in both one-dimensional and two-dimensional filter designs.

Information exchange through a relay node is attracting attention for applying machine-to-machine communications. If the node demodulates the received signal in relay processing confidentially, the information leakage through the relay station is a problem. In wireless MIMO switching, the frequency spectrum usage efficiency can be improved owing to the completion of information exchange within a short time. This study proposes a novel wireless MIMO switching method for secure information exchange. An overloaded situation, in which the access nodes are one larger than the number of antennas in the relay node, makes the demodulation of the relay node difficult. The access schedule of nodes is required for maintaining the overload situation and the high information exchange efficiency. This study derives the equation model of the access schedule and constructs an access schedule with fewer time periods in the integer programming problem. From the computer simulation, we confirm that the secure capacity of the proposed MIMO switching is larger than that of the original one, and the constructed access schedule is as large as the ideal and minimum time period for information exchange completion.

We propose a spectrum regeneration and demodulation method for multiple direct RF undersampled real signals by using a new algorithm. Many methods have been proposed to regenerate the RF spectrum by using undersampling because of its simple circuit architecture. However, it is difficult to regenerate the spectrum from a real signal that has a band wider than a half of the sampling frequency, because it is difficult to include complex conjugate relation of the folded spectrum into the linear algebraic equation in this case. We propose a new spectrum regeneration method from direct undersampled real signals that uses multiple clocks and an extended algorithm considering the complex conjugate relation. Simulations are used to verify the potential of this method. The validity of the proposed method is verified by using the simulation data and the measured data. We also apply this algorithm to the demodulation system.

This paper demonstrates that a 360° radio-frequency phase detector consisting of a combination of symmetrical mixers and 45° phase shifters with tunable devices can achieve a low phase-detection error over a wide frequency range. It is shown that the phase detection error does not depend on the voltage gain of the 45° phase shifter. This allows the usage of tunable devices as 45° phase shifters for a wide frequency range with low phase-detection errors. The fabricated phase detector having tunable low-pass filters as the tunable device demonstrates phase detection errors lower than 2.0° rms in the frequency range from 3.0 GHz to 10.5 GHz.

In view of the different spatial and temporal resolutions of observed multi-source heterogeneous carbon dioxide data and the uncertain quality of observations, a data fusion prediction model for observed multi-scale carbon dioxide concentration data is studied. First, a wireless carbon sensor network is created, the gross error data in the original dataset are eliminated, and remaining valid data are combined with kriging method to generate a series of continuous surfaces for expressing specific features and providing unified spatio-temporally normalized data for subsequent prediction models. Then, the long short-term memory network is used to process these continuous time- and space-normalized data to obtain the carbon dioxide concentration prediction model at any scales. Finally, the experimental results illustrate that the proposed method with spatio-temporal features is more accurate than the single sensor monitoring method without spatio-temporal features.

Binary sequence pairs with optimal periodic correlation have important applications in many fields of communication systems. In this letter, four new families of binary sequence pairs are presented based on the generalized cyclotomy over Z5q, where q ≠ 5 is an odd prime. All these binary sequence pairs have optimal three-level correlation values {-1, 3}.

This paper proposes new acoustic feature signatures based on the multiscale fractal dimension (MFD), which are robust against the diversity of environmental sounds, for the content-based similarity search. The diversity of sound sources and acoustic compositions is a typical feature of environmental sounds. Several acoustic features have been proposed for environmental sounds. Among them is the widely-used Mel-Frequency Cepstral Coefficients (MFCCs), which describes frequency-domain features. However, in addition to these features in the frequency domain, environmental sounds have other important features in the time domain with various time scales. In our previous paper, we proposed enhanced multiscale fractal dimension signature (EMFD) for environmental sounds. This paper extends EMFD by using the kernel density estimation method, which results in better performance of the similarity search tasks. Furthermore, it newly proposes another acoustic feature signature based on MFD, namely very-long-range multiscale fractal dimension signature (MFD-VL). The MFD-VL signature describes several features of the time-varying envelope for long periods of time. The MFD-VL signature has stability and robustness against background noise and small fluctuations in the parameters of sound sources, which are produced in field recordings. We discuss the effectiveness of these signatures in the similarity sound search by comparing with acoustic features proposed in the DCASE 2018 challenges. Due to the unique descriptiveness of our proposed signatures, we confirmed the signatures are effective when they are used with other acoustic features.

In this paper, we present the transmission characteristics control of a 125 GHz-band split-ring resonator (SRR) bandstop filter by coupling an alignment-free lattice pattern. We demonstrate that the transmission characteristics of the SRR filter can be controlled by coupling the lattice pattern; however, the required accuracy of alignment between the SRR filter and lattice pattern was below 200 µm. Therefore, we designed an alignment-free lattice pattern whose unit cell size is different from that of the SRR unit cell. S21 of the SRR bandstop filter changes from -38.7 to -4.0 dB at 125 GHz by arranging the alignment-free lattice pattern in close proximity to the SRR stopband filter without alignment. A 10 Gbit/s data transmission can be achieved over a 125 GHz-band wireless link by setting the alignment-free lattice pattern substrate just above the SRR bandstop filter.

Linear programming (LP) decoding based on the alternating direction method of multipliers (ADMM) has proved to be effective for low-density parity-check (LDPC) codes. However, for high-density parity-check (HDPC) codes, the ADMM-LP decoder encounters two problems, namely a high-density check matrix in HDPC codes and a great number of pseudocodewords in HDPC codes' fundamental polytope. The former problem makes the check polytope projection extremely complex, and the latter one leads to poor frame error rates (FER) performance. To address these issues, we introduce the even vertex algorithm (EVA) into the ADMM-LP decoding algorithm for HDPC codes, named as HDPC-EVA. HDPC-EVA can reduce the complexity of the projection process and improve the FER performance. We further enhance the proposed decoder by the automorphism groups of codes, creating diversity in the parity-check matrix. The simulation results show that the proposed decoder is capable of cutting down the average decoding time for each iteration by 30%-60%, as well as achieving near maximum likelihood (ML) performance on some BCH codes.

Long-range radars (LRRs) for higher level autonomous driving (AD) will require more antennas than simple driving assistance. The point at issue here is 50-60% of the LRR module area is used for antennas. To miniaturize LRR modules, we use horn and lens antenna with highly efficient gain. In this paper, we propose two high-density implementation techniques for radio-frequency (RF) front-end using horn and lens antennas. In the first technique, the gap between antennas was eliminated by taking advantage of the high isolation performance of horn and lens antennas. In the second technique, the RF front-end including micro-strip-lines, monolithic microwave integrated circuits, and peripheral parts is placed in the valley area of each horn. We fabricated a prototype LRR operating at 77 GHz with only one printed circuit board (PCB). To detect vehicles horizontally and vertically, this LRR has a minimum antenna configuration of one Tx antenna and four Rx antennas placed in 2×2 array, and 30 mm thickness. Evaluation results revealed that vehicles could be detected up to 320 m away and that the horizontal and vertical angle error was less than +/- 0.2 degrees, which is equivalent to the vehicle width over 280 m. Thus, horn and lens antennas implemented using the proposed techniques are very suitable for higher level AD LRRs.

For improving the fifth-generation mobile communication system, a highly efficient power amplifier must be designed for the base station. An outphasing amplifier is expected to be a solution for achieving high efficiency. We designed a combiner, one of the key components of the outphasing amplifier, using a serial Chireix combiner and fabricated an amplifier with a GaN HEMT, achieving 70% or more high efficiency up to 9 dB back-off power in an 800 MHz band. We also fabricated a 2 GHz-band outphasing amplifier with the same design. We applied digital predistortion (DPD) to control the balance of amplifying units in this amplifier and achieved an average efficiency of 65% under a 20 MHz modulation bandwidth.

A practical Doherty amplifier design method has been developed based on an asymmetric configuration scheme. By embedding a load modulation function into matching circuits of a carrier amplifier (CA) and a peaking amplifier (PA) in the Doherty amplifier, an issue of the Doherty amplifier design is boiled down to the CA and PA matching circuit design. The method can be applied to transistors with unknown parasitic elements if optimum termination impedance conditions for the transistor are obtained from a source-/load-pull technique in simulation or measurement. The design method was applied to GaN HEMT Doherty amplifier MMICs. The fabricated 4.5-GHz-band GaN HEMT Doherty amplifier MMIC exhibited a maximum drain efficiency of 66% and a maximum power-added efficiency (PAE) of 62% at 4.1GHz, with a saturation output power of 36dBm. In addition, PAE of 50% was achieved at 4.1GHz on a 7.2-dB output back-off (OBO) condition. The fabricated 8.5-GHz-band GaN HEMT Doherty amplifier MMIC exhibited a maximum drain efficiency of 53% and a maximum PAE of 44% at 8.6GHz, with a saturation output power of 36dBm. In addition, PAE of 35% was achieved at 8.6GHz on a 6.7-dB (OBO). And, the fabricated 12-GHz-band GaN HEMT Doherty amplifier MMIC exhibited a maximum drain efficiency of 57% and a maximum PAE of 52% at 12.4GHz, with a saturation output power of 34dBm. In addition, PAE of 32% was achieved at 12.4GHz on a 9.5-dB (OBO) condition.

Research on wireless power transmission technology is being actively conducted, and studies on spatial transmission methods such as SSPS are currently underway for applications such as power transfer to the upper part of steel towers and power transfer to flying objects such as drones. To enable such applications, it is necessary to examine the configuration of the power-transfer and power-receiving antennas and to improve the RF-DC conversion efficiency (hereinafter referred to as conversion efficiency) of the rectifier circuit on the power-receiving antenna. To improve the conversion efficiency, various methods that utilize full-wave rectification rather than half-wave rectification have been proposed. However, these come with problems such as a complicated circuit structure, the need for additional capacitors, the selection of components at high frequencies, and a reduction in mounting yield. In this paper, we propose a method to improve the conversion efficiency by loading a high-impedance microstrip line as a feedback line in part of the rectifier circuit. We analyzed a class-F rectifier circuit using circuit analysis software and found that the conversion efficiency of the conventional configuration was 54.2%, but the proposed configuration was 69.3%. We also analyzed a measuring circuit made with a discrete configuration in the 5.8-GHz band and found that the conversion efficiency was 74.7% at 24dBm input.