This paper describes a method to evaluate the modulated waveforms output by a high-speed external phase modulator over a wide wavelength range by using linear optical sampling (LOS) and a wavelength-swept light source. The phase-modulated waveform is sampled by LOS together with the reference signal before modulation, and the modulation waveform is observed by removing the phase noise of the light source extracted from the reference signal. In this process, the frequency offset caused by the optical-path length difference between the measurement and reference interferometers is removed by digital signal processing. A pseudo-random binary-sequence modulated signal is observed with a temporal resolution of 10ps. We obtained a dynamic range of ∼40dB for the measurement bandwidth of 10 nm. When the measurement bandwidth is expanded to entire C-Band (∼35nm), the dynamic ranges of 37∼46dB were observed, depending on the wavelengths. The measurement time was sub-seconds throughout the experiment.

Low-hit-zone frequency-hopping sequences (LHZ-FHSs) are frequency-hopping sequences with low Hamming correlation in a low-hit-zone (LHZ), which have important applications in quasi-synchronous communication systems. However, the strict quasi-synchronization may be hard to maintain at all times in practical FHMA networks, it is also necessary to minimize the Hamming correlation for time-shifts outside of the LHZ. The main objective of this letter is to propose a lower bound on the maximum correlation magnitude outside the low-hit-zone for LHZ-FHS sets. It turns out that the proposed bound is tight or almost tight in the sense that it can be achieved by some LHZ-FHS sets.

Optical phase conjugation (OPC) is an all-optical signal processing technique for mitigating fiber nonlinearity and is promising for building cost-efficient fiber networks with few optic-electric-optic conversions and long amplification spacing. In lumped amplified systems, OPC has a little nonlinearity mitigation efficiency for nonlinear distortion induced by cross-phase modulation (XPM) due to the asymmetry of power and chromatic dispersion (CD) maps during propagation in transmission fiber. In addition, the walk-off of XPM-induced noise becomes small due to the CD compensation effect of OPC, so the deterministic nonlinear distortion increases. Therefore, lumped amplified transmission systems with OPC are more sensitive to channel spacing than conventional systems. In this paper, we show the channel spacing dependence of NZ-DSF transmission using amplification repeater with OPC. Numerical simulations show comprehensive characteristics between channel spacing and CD in a 100-Gbps/λ WDM signal. An experimental verification using periodically poled LiNbO3-based OPC is also performed. These results suggest that channel spacing design is more important in OPC-assisted systems than in conventional dispersion-unmanaged systems.

At present, the application of different types of memristors in electronics is being deeply studied. Given the nonlinearity characterizing memristors, a circuit with memristors cannot be treated by classical circuit analysis. In this paper, memristor is equivalent to a nonlinear dynamic system composed of linear dynamic system and nonlinear static system by Volterra series. The nonlinear transfer function of memristor is derived. In the complex frequency domain, the n-order complex frequency response of memristor is established by multiple Laplace transform, and the response of MLC parallel circuit is taken as an example to verify. Theoretical analysis shows that the complex frequency domain analysis method of memristor transforms the problem of solving nonlinear circuit in time domain into n times complex frequency domain analysis of linear circuit, which provides an idea for nonlinear dynamic system analysis.

Combinatorial testing is an effective testing technique for detecting faults in a software or hardware system with multiple factors using combinatorial methods. By performing a test, which is an assignment of possible values to all the factors, and verifying whether the system functions as expected (pass) or not (fail), the presence of faults can be detected. The failures of the tests are possibly caused by combinations of multiple factors assigned with specific values, called faulty interactions. Martínez et al. [1] proposed the first deterministic adaptive algorithm for discovering faulty interactions involving at most two factors where each factor has two values, for which graph representations are adopted. In this paper, we improve Martínez et al.'s algorithm by an adaptive algorithmic approach for discovering faulty interactions in the so-called “non-2-locatable” graphs. We show that, for any system where each “non-2-locatable factor-component” involves two faulty interactions (for example, a system having at most two faulty interactions), our improved algorithm efficiently discovers all the faulty interactions with an extremely low mistaken probability caused by the random selection process in Martínez et al.'s algorithm. The effectiveness of our improved algorithm are revealed by both theoretical discussions and experimental evaluations.

The NIST post-quantum project intends to standardize cryptographic systems that are secure against attacks by both quantum and classical computers. One of these cryptographic systems is NewHope that is a RING-LWE based key exchange scheme. The NewHope Key Encapsulation Method (KEM) allows to establish an encapsulated (secret) key shared by two participants. This scheme defines a private key that is used to encipher a random shared secret and the private key enables the deciphering. This paper presents Fault Information Leakage attacks, using conventional personal computers, if the attacked participant, say Bob, reuses his public key. This assumption is not so strong since reusing the pair (secret, public) keys saves Bob's device computing cost when the public global parameter is not changed. With our result we can conclude that, to prevent leakage, Bob should not reuse his NewHope secret and public keys because Bob's secret key can be retrieved with only 2 communications. We also found that Bob's secret keys can be retrieved for NewHopeToy2, NewHopeToy1 and NewHopeLudicrous with 1, 2, and 3 communications, respectively.

Numerous variable tap-length algorithms can be found in some literature and few strategies are derived from a basic theoretical formula. Thus, some algorithms lack of theoretical depth and their performance are unstable. In view of this point, the novel variable tap-length algorithm which is based on the mixed error cost function is presented in this letter. By analyzing the mixed expectation of the prior and the posterior error, the novel variable tap-length strategy is derived. The proposed algorithm has a more valid proximity to the optimal tap-length and a good convergence ability by the performance analysis. It can solve many deficiencies comprising large fluctuations of the tap-length, the high complexity and the weak steady-state ability. Simulation results demonstrate that the proposed algorithm equips good performance.

Rain attenuation characteristics due to typhoon passage are discussed using the Ku-band BS satellite signal observations conducted by Osaka Electro-Communication University in Neayagawa from 1988 to 2019. The degree of hourly rain attenuation due to rainfall rate is largely enhanced as typhoon passes the east side of the station, while it becomes smaller in the case of west side passage. Compared to hourly ground wind velocities of nearby AMeDAS, the equivalent path lengths of rain attenuation become larger as the wind directions approach the same angle to the satellite, while they become smaller as the wind directions approach the opposite angle to the satellite. The increase and decrease of the equivalent path lengths are confirmed in other Ku-band and Ka-band satellite paths with different azimuth angles, such as CS, SKP, and SBC. Modified equivalent path lengths calculated by a simple propagation path model including horizontal wind speeds along the same direction to the satellite agree well with the equivalent path lengths observed by each satellite. The equivalent path lengths are, for the first time, proved to be largely affected by the direction of typhoon passage and the horizontal wind velocities.

A 32-bit arithmetic logic unit (ALU) is designed for a rapid single flux quantum (RSFQ) bit-parallel processor. In the ALU, clocked gates are partially replaced by clockless gates. This reduces the number of D flip flops (DFFs) required for path balancing. The number of clocked gates, including DFFs, is reduced by approximately 40 %, and size of the clock distribution network is reduced. The number of pipeline stages becomes modest. The layout design of the ALU and simulation results show the effectiveness of using clockless gates in wide datapath circuits.

The adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic element based on the quantum flux parametron. AQFP circuits can operate with energy dissipation near the thermodynamic and quantum limits by maximizing the energy efficiency of adiabatic switching. We have established the design methodology for AQFP logic and developed various energy-efficient systems using AQFP logic, such as a low-power microprocessor, reversible computer, single-photon image sensor, and stochastic electronics. We have thus demonstrated the feasibility of the wide application of AQFP logic in future information and communications technology. In this paper, we present a tutorial review on AQFP logic to provide insights into AQFP circuit technology as an introduction to this research field. We describe the historical background, operating principle, design methodology, and recent progress of AQFP logic.

The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.

The adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic device. In a previous study, we proposed a low-latency clocking scheme called delay-line clocking, and several low-latency AQFP logic gates have been demonstrated. In delay-line clocking, the latency between adjacent excitation phases is determined by the propagation delay of excitation currents, and thus the rising time of excitation currents should be sufficiently small; otherwise, an AQFP gate can switch before the previous gate is fully excited. This means that delay-line clocking needs high clock frequencies, because typical excitation currents are sinusoidal and the rising time depends on the frequency. However, AQFP circuits need to be tested in a wide frequency range experimentally. Hence, in the present study, we investigate AQFP circuits adopting delay-line clocking with square excitation currents to apply delay-line clocking in a low frequency range. Square excitation currents have shorter rising time than sinusoidal excitation currents and thus enable low frequency operation. We demonstrate an AQFP buffer chain with delay-line clocking using square excitation currents, in which the latency is approximately 20ps per gate, and confirm that the operating margin for the buffer chain is kept sufficiently wide at clock frequencies below 1GHz, whereas in the sinusoidal case the operating margin shrinks below 500MHz. These results indicate that AQFP circuits adopting delay-line clocking can operate in a low frequency range by using square excitation currents.

A Josephson parametric oscillator (JPO) is an interesting system from the viewpoint of quantum optics because it has two stable self-oscillating states and can deterministically generate quantum cat states. A theoretical proposal has been made to operate a network of multiple JPOs as a quantum annealer, which can solve adiabatically combinatorial optimization problems at high speed. Proof-of-concept experiments have been actively conducted for application to quantum computations. This article provides a review of the mechanism of JPOs and their application as a quantum annealer.

We experimentally evaluated random number sequences generated by a superconducting hardware random number generator composed of a Josephson-junction oscillator, a rapid-single-flux-quantum (RSFQ) toggle flip-flop (TFF), and an RSFQ AND gate. Test circuits were fabricated using a 10 kA/cm2 Nb/AlOx/Nb integration process. Measurements were conducted in a liquid helium bath. The random numbers were generated for a trigger frequency of 500 kHz under the oscillating Josephson-junction at 29 GHz. 26 random number sequences of 20 kb length were evaluated for bias voltages between 2.0 and 2.7 mV. The NIST FIPS PUBS 140-2 tests were used for the evaluation. 100% pass rates were confirmed at the bias voltages of 2.5 and 2.6 mV. We found that the Monobit test limited the pass rates. As numerical simulations suggested, a detailed evaluation for the probability of obtaining “1” demonstrated the monotonical dependence on the bias voltage.

Extremely energy-efficient logic devices are required for future low-power high-performance computing systems. Superconductor electronic technology has a number of energy-efficient logic families. Among them is the adiabatic quantum-flux-parametron (AQFP) logic family, which adiabatically switches the quantum-flux-parametron (QFP) circuit when it is excited by an AC power-clock. When compared to state-of-the-art CMOS technology, AQFP logic circuits have the advantage of relatively fast clock rates (5 GHz to 10 GHz) and 5 - 6 orders of magnitude reduction in energy before cooling overhead. We have been developing extremely energy-efficient computing processor components using the AQFP. The adder is the most basic computational unit and is important in the development of a processor. In this work, we designed and measured a 16-bit parallel prefix carry look-ahead Kogge-Stone adder (KSA). We fabricated the circuit using the AIST 10 kA/cm2 High-speed STandard Process (HSTP). Due to a malfunction in the measurement system, we were not able to confirm the complete operation of the circuit at the low frequency of 100 kHz in liquid He, but we confirmed that the outputs that we did observe are correct for two types of tests: (1) critical tests and (2) 110 random input tests in total. The operation margin of the circuit is wide, and we did not observe any calculation errors during measurement.

Quantum combinatorial designs are gaining popularity in quantum information theory. Quantum Latin squares can be used to construct mutually unbiased maximally entangled bases and unitary error bases. Here we present a general method for constructing quantum Latin arrangements from irredundant orthogonal arrays. As an application of the method, many new quantum Latin arrangements are obtained. We also find a sufficient condition such that the improved quantum orthogonal arrays [10] are equivalent to quantum Latin arrangements. We further prove that an improved quantum orthogonal array can produce a quantum uniform state.

When collecting images, owing to the influence of shooting equipment, shooting environment, and other factors, often low-illumination images with insufficient exposure are obtained. For low-illumination images, it is necessary to improve the contrast. In this paper, a digital color image contrast enhancement method based on luminance weight adjustment is proposed. This method improves the contrast of the image and maintains the detail and nature of the image. In the proposed method, the illumination of the histogram equalization image and the adaptive gamma correction with weighted distribution image are adjusted by the luminance weight of w1 to obtain a detailed image of the bright areas. Thereafter, the suppressed multi-scale retinex (MSR) is used to process the input image and obtain a detailed image of the dark areas. Finally, the luminance weight w2 is used to adjust the illumination component of the detailed images of the bright and dark areas, respectively, to obtain the output image. The experimental results show that the proposed method can enhance the details of the input image and avoid excessive enhancement of contrast, which maintains the naturalness of the input image well. Furthermore, we used the discrete entropy and lightness order error function to perform a numerical evaluation to verify the effectiveness of the proposed method.

In this paper, we review the basic components of superconducting quantum computers. We mainly focus on the packaging and wiring technologies required to realize large-scalable superconducting quantum computers.

We study the continuous similarity search problem for evolving queries which has recently been formulated. Given a data stream and a database composed of n sets of items, the purpose of this problem is to maintain the top-k most similar sets to the query which evolves over time and consists of the latest W items in the data stream. For this problem, the previous exact algorithm adopts a pruning strategy which, at the present time T, decides the candidates of the top-k most similar sets from past similarity values and computes the similarity values only for them. This paper proposes a new exact algorithm which shortens the execution time by computing the similarity values only for sets whose similarity values at T can change from time T-1. We identify such sets very fast with frequency-based inverted lists (FIL). Moreover, we derive the similarity values at T in O(1) time by updating the previous values computed at time T-1. Experimentally, our exact algorithm runs faster than the previous exact algorithm by one order of magnitude and as fast as the previous approximation algorithm.

This study tries to predict date of ear emergence of rice plants, based on cropping records over 25 years. Predicting ear emergence of rice plants is known to be crucial for practicing good harvesting quality, and has long been dependent upon old farmers who acquire skills of intuitive prediction based on their long term experiences. Facing with aging farmers, data driven approach for the prediction have been pursued. Nevertheless, they are not necessarily sufficient in terms of practical use. One of the issue is to adopt weather forecast as the feature so that the predictive performance is varied by the accuracy of the forecast. The other issue is that the performance is varied by region and the regional characteristics have not been used as the features for the prediction. With this background, we propose a feature engineering to quantify hidden regional characteristics as the feature for the prediction. Further the feature is engineered based only on observational data without any forecast. Applying our proposal to the data on the cropping records resulted in sufficient predictive performance, ±2.69days of RMSE.