An interference cancellation (ICAN) scheme for mobile communication radio repeaters is presented. When a radio repeater has a gain that is larger than the isolation between its transmit and receive antennas, it oscillates due to feedback interference signals. To prevent feedback oscillation of a radio repeater, we first formulate a feedback oscillation model of the radio repeater and then derive an ICAN model from that model. From the derived ICAN model, we show that the stability and the signal quality of the repeater depend on the repeater's gain and delay, the propagation delay on feedback paths, feedback channel characteristics, and the capability of the feedback channel estimation algorithm. It is also shown that the stability condition of the repeater does not guarantee the quality of the repeater's output signal. To guarantee repeater's stability and signal quality, an ICAN scheme based on an iterative algorithm is subsequently proposed. The simulation results confirm the relationship between the stability and signal quality of the repeater and the impact of the aforementioned factors. Using the proposed ICAN scheme, a mean error vector magnitude (quality indicator) of about 6.3% for the repeater's output signal was achieved.

Single-carrier (SC) multiple access is a promising uplink multiple access technique because of its low peak-to-average power ratio (PAPR) property and high frequency diversity gain that is achievable through simple one-tap frequency-domain equalization (FDE) in a strong frequency-selective channel. The multiple access capability can be obtained by combining either frequency division multiple access (FDMA) or code division multiple access (CDMA) with SC transmission. In this article, we review the recent research on the SC multiple access techniques with one-tap FDE. After introducing the principle of joint FDE/antenna diversity combining, we review various SC multiple access techniques with one-tap FDE, i.e., SC-FDMA, SC-CDMA, block spread CDMA, and delay-time/CDMA.

The use of frequency-domain interleaving on a frame-by-frame basis for orthogonal frequency division multiplexing (OFDM) combined with time division multiplexing (OFDM/TDM) is presented. In conventional OFDM, FDE is not designed to exploit the channel frequency-selectivity and consequently, the frequency diversity gain cannot be obtained. To further improve the bit error rate (BER) performance of conventional OFDM an interleaving technique may be applied, but FDE cannot be fully exploited. In this letter, the OFDM/TDM signal (i.e., several concatenated OFDM signals) frequency components are interleaved at the transmitter and then, minimum mean square error frequency-domain equalization (MMSE-FDE) is applied at the receiver to obtain a larger frequency diversity gain. It is shown that frequency-domain interleaving on a frame-by-frame basis for OFDM/TDM using MMSE-FDE achieves improved BER performance in comparison with conventional OFDM due to enhanced frequency diversity gain.

This paper proposes a novel RBF training algorithm based on immune operations for dynamic problem solving. The algorithm takes inspiration from the dynamic nature of natural immune system and locally-tuned structure of RBF neural network. Through immune operations of vaccination and immune response, the RBF network can dynamically adapt to environments according to changes in the training set. Simulation results demonstrate that RBF equalizer based on the proposed algorithm obtains good performance in nonlinear time-varying channels.

Automatic location identification is required for emergency calls in Japan and many other countries. However, promptly providing a reliable position is a problem in places where the global positioning system (GPS) signal is extremely weak. We propose an acquisition scheme for the assisted GPS (AGPS) architecture based on a timing-synchronized mobile network. System errors as well as code uncertainty range and frequency uncertainty range are discussed. With this method, the acquisition search range is significantly reduced, and a long-time coherent correlation is made possible. Simulations and experiments prove that the method is fast, efficient and power-saving for the user handset. Furthermore, the AGPS receiver can perform a short TTFF (Time To First Fix) start even with no ephemeris kept in the handset.

In this paper, we study and propose an inter-cell co-channel interference (CCI) mitigation method for pilot signals using cyclic shift Zadoff-Chu (CS-ZC) sequences for SC-FDMA-based uplink without tight scheduler coordination among cells. Firstly, we investigate the issue of severe detection performance degradation created by the lack of orthogonality among the pilot signals without alignment of the allocated frequency resource positions among cells when using the conventional CS-ZC sequences generation scheme. Secondly, we identify the primary factor causing the issue. Thirdly, we propose a frequency-dependent CS-ZC sequence generation scheme by allocating the same spectrum elements of the ZC sequence to the overlapped subcarriers among cells to mitigate the inter-cell CCI of the pilot signals without alignment of the frequency resource positions among cells. Finally, we confirm the validity of the proposal using uplink data BLER evaluation under a multipath fading condition by computer simulation compared to the conventional method, and show that the proposal achieves around 0.9 dB and 0.6 dB better performance at 10% BLER than the conventional method for 1 RB and 2 RBs frequency offsets in 3 RBs transmission bandwidth, respectively.

The critical problem of the pseudo-noise (PN) code acquisition system is the contradiction between the acquisition performance and the calculation complexity. This paper presents a low cost correlator (LCC) structure that can search for two PN code phases in a single accumulation period by eliminating redundant computation. Compared with the part-parallel structure that is composed of two serial correlators (PARALLEL2), the proposed LCC structure has the same performance while saves about 22% chip area and 34% power consumption if uses the Carry-look-ahead (CLA) adder, 17% chip area and 25% power consumption if uses the Ripple-carry (RPL) adder.

Time variations of wireless multipath channels can lead to severe intercarrier interference (ICI) in orthogonal frequency division multiplex (OFDM) systems, whereas large Doppler frequency spread can provide us with time diversity gain. In order to take advantage of the time diversity and to suppress the interference and noise enhancement at the same time, the receiver normally detects the data successively. In this letter, we propose an improved detection ordering based on the log-likelihood ratio (LLR) rather than the signal-to-noise ratio (SNR) for the successive detector. Using both theoretical analysis and computer simulation, it is shown that this scheme outperforms the traditional successive detection methods.

The first part of this paper contains an introduction to Bell inequalities and Tsirelson's theorem for the non-specialist. The next part gives an explicit optimum construction for the "hard" part of Tsirelson's theorem. In the final part we describe how upper bounds on the maximal quantum violation of Bell inequalities can be obtained by an extension of Tsirelson's theorem, and survey very recent results on how exact bounds may be obtained by solving an infinite series of semidefinite programs.

Quantum random access coding (QRAC) is one of the basic tools in quantum computing. It uses a quantum state for encoding the sender's bit string so that the receiver can recover any single bit of the bit string with high probability. This article surveys recent developments of QRAC, with some concrete examples of QRAC using one quantum bit, and its applications, focusing on communication complexity and locally decodable codes.

In this paper, a compact channel thermal noise model for short-channel MOSFETs is presented and applied to the radio frequency integrated circuit (RFIC) design. Based on the analysis of the relationship among different short-channel effects such as velocity saturation effect (VSE), channel-length modulation (CLM), and carrier heating effect (CHE), the compact model for the channel thermal noise was analytically derived as a simple form. In order to simulate MOSFET's noise characteristics in circuit simulators, an appropriate methodology is proposed. The used compact noise model is verified by comparing simulated results to the measured data at device and circuit level by using 65 nm and 130 nm CMOS technologies, respectively.

This paper focuses on the collaborative learning of mathematics in which learners effectively acquire knowledge of common exercises through discussion with other learners. During collaborative learning, learners sometimes cannot solve exercises successfully, because they cannot derive answers by themselves or they hesitate to propose answers through discussion. To cope with such situations, this paper proposes two support functions using diagrams to encourage active discussion, since diagrams are often used to graphically illustrate mathematical concepts. One function indicates the differences between learner diagrams and the group diagram in order to encourage participation in discussions. To compare the characteristics of diagrams drawn by different learners, internal representation of the diagram, which consists of types of figures and remarkable relations to other figures, is introduced. The other function provides hints in the group diagram so that all learners can consider their answers collaboratively through discussions. Since preparing hints for all exercises is difficult, rules for drawing supplementary figures, which are general methods for drawing supplementary figures that correspond to individual answering methods/formulas, are also developed. By applying available rules to current group diagram, appropriate supplementary figures that can solve current learning situations may be generated. The experimental results showed that the generated hints successfully increased the number of utterances in the groups. Moreover, learners were also able to derive answers by themselves and tended to propose more opinions in discussions when the uniqueness of their diagrams was indicated.

This paper proposes a novel dependable SRAM with 7T/14T memory cells, and introduces a new concept, "quality of a bit (QoB)" for it. The proposed SRAM has three modes: a normal mode, high-speed mode, and dependable mode, and dynamically scales its reliability, power and speed by combining two memory cells for one-bit information (i.e. 14 T/bit). By carrying out Monte Carlo simulation in a 65-nm process technology, the minimum voltages in read and write operations are improved by 0.21 V and 0.26 V, respectively, with a bit error rate of 10-8 kept. In addition, we confirm that the dependable mode achieves a lower bit error rate than the error correction code (ECC) and multi module redundancy (MMR). Furthermore, we propose a new memory array structure to avoid the half-selection problem in a write operation. The respective cell area overheads in the normal mode are 26% and 11% in the cases where additional transistors are pMOSes and nMOSes, compared to the conventional 6T memory cell.

An on-chip power supply noise canceller with higher voltage supply and switching transistor is proposed and the effectiveness of the canceller is experimentally verified. The noise canceller is effective for nano-second order noise caused by circuit wakeup or step increase of frequency in frequency hopping. The principle of the noise canceller is to reduce the current flowing through the supply line of VDD by injecting additional current from the higher voltage supply, so that the voltage drop across the VDD supply line is reduced. As additional current flow from higher supply, switching transistor has to be turned off not to increase the power consumption. With turn-off time of 2L/R, this current can be turned off without inducting another droop due to the increase of current flowing through the power supply line. The measurement shows the canceller reduces 68% of the noise with load circuit equivalent to 530 k logic gates in 90-nm CMOS with 9% wire overhead, 1.5% area overhead, and 3% power overhead at 50 k wake-ups/s. Compared to passive noise reduction, proposed noise canceller reduces power supply noise by 64% without wire overhead and to achieve same noise reduction with passive method, 77 times more C or 45 times less L is required. Too large switching transistor results in saturated noise reduction effect and higher power consumption. A rule-of-thumb is to set the on-resistance to supply 100% of load current when turned-on.

In this study, a performance isolation mechanism based on a fuzzy control technique is developed in such a way that ambiguous situations caused when estimating the workload of cluster-based web servers, client request rates, and dynamic request rates can be represented effectively. The proposed mechanism involving a fuzzy-based technique is compared with a non-fuzzy technique in terms of the response time in the 95th percentile. Experiments showed that the proposed technique improves the performance of web servers that provide differentiated services.

A call admission control (CAC) scheme based on statistical information is proposed, called the statistical CAC scheme. A conventional scheme needs to manage session information for each link to update the residual bandwidth of a network in real time. This scheme has a scalability problem in terms of network size. The statistical CAC rejects session setup requests in accordance to a pre-computed ratio, called the rejection ratio. The rejection ratio is computed by using statistical information about the bandwidth requested for each link so that the congestion probability is less than an upper bound specified by a network operator. The statistical CAC is more scalable in terms of network size than the conventional scheme because it does not need to keep accommodated session state information. Numerical results show that the statistical CAC, even without exact session state information, only slightly degrades network utilization compared with the conventional scheme.

In this letter, a new joint precoding and decoding design scheme for multiuser MIMO downlink is proposed which dispenses with iterative operations and can achieve better performance. This scheme introduces zero-force processing into minimum mean square error (MMSE) design scheme to avoid iterative operations. We derived closed-form precoders and decoders and transmit power allocation strategy of proposed design scheme, validated performance of proposed design scheme by computer simulation. The simulation results show that the proposed design scheme can achieve better bit error rate (BER) and sum capacity performance compared to an existing non-iterative design scheme.

In this letter, we propose a novel signal detection method, reduced complexity QRM-MLD, which achieves almost identical error performance to that of the conventional QRM-MLD while significantly reducing the computational complexity.

This paper presents a deadbeat control scheme for linear systems with state constraints. The proposed controller increases the number of steps on-line for the deadbeat tracking performance, satisfying given admissible state constraints. LMI conditions are given to minimize the unavoidable step delay. The proposed schemes can be easily developed by using LMI approach, and are validated by numerical simulation.

A dual band 0.18 µm CMOS LC-tank injection locked frequency divider (ILFD) is proposed. The ILFD circuit is realized with a cross-coupled pMOS LC-tank oscillator with an inductor switch for frequency band selection. The self-oscillating VCO is injection-locked by nth-harmonic input to obtain the division factor of n. The division ratio of 1, 2, and 3 has been found for the proposed ILFD. Measurement results show that at the supply voltage of 1.1 V, the free-running frequency is from 2.28(3.09) GHz to 2.78(3.72) GHz for the low- (high-) frequency band. The power consumption of the ILFD core is 3.7 mW (6.2 mW) at low (high) band. The total area including the output buffer and the pads is 0.8410.764 mm2.