In this paper, we evaluated performance of mobile exchange control network. Queueing network model is used for modeling of mobile exchange control network. We developed a call control processing and location registration scenario that has a message exchange function between processors in mobile exchange control network. The network symbols are used the simulation models that are composed of the initialization module, message generation module, message routing module, message processing module, message generation module, HIPC network processing module, output analysis module. As a result of computer simulation, we obtain the processor utilization, the mean queue length, the mean waiting time of control network based on call processing and location registration capacity. The call processing and location registration capacity are referred by the number of call attempts in the mobile exchange and must be satisfied with the quality of service (delay time).

We present a new class of trellis-codes for partial-response channel. Our code configuration is based on the coded 1 - D scheme due to Wolf and Ungerboeck. However, no precoder between a convolutional encoder and the partialresponse channel is used. A new lower bound on the minimum free squared Euclidean distance of channel code is shown. The bound is available for any PR channel with a finite response. New codes for 1 - D and (1 - D) (1 + D)2 channels are found by computer code search using the lower bound. Some of the new codes have excellent properties: a significant d2free and a small decoding complexity.

The use of existing metallic local line facilities is being studied for the provision of high-speed digital transmission services. Local line characteristics have to be modeled in the form of the objective requirements that should be met by DSL for estimating the feasibility of the service provision in the actual network. This paper presents the results of a study that models the metallic media characteristics of NTT's local network. First, the line lenghts determined by the existing local line deployment rule and the cable types used in the networks are introduced. Second, the values of crosstalk characteristics, the most significant factors in limiting DSL range, are given by classifying essential line conditioning states of each cable. The values of crosstalk characteristics are newly computed by taking into account detailed cable pair-binding (cabling) structures, and the worst case values among all possible combinations of multiple inter-pair interfering-interfered relationships within a cable are given though a previous study approximated cable pair-binding structures. The crosstalk characteristics of NTT's and American local networks are also compared. A modified approximate equation of line propagation characteristics is also proposed for representative local lines, and its precision is verified by comparing simulation results to actual measurements in both frequency and time domains.

We present a current mode cyclic analog-to-digital converter that is suitable for submicron LSI fabrication processes. Our converter is composed of sample-and-hold circuits with regulated cascode configuration which offers high output impedance and wide outoput range. The circuit requires small area since the architecture depends on neither precise analog transistors nor ratio-matched capacitors. We have designed and fabricated a test circuit that has an area of 0.014mm2 using a 0.8µm CMOS process. The circuit is examined to perform 8-bit resolution at a sampling rate of 40kHz and average power dissipation of 370µW at 4V supply voltage.

As current-voltage characteristics of GaAs MESFET differ from those of BJT and MOSFET and n-channel FET is only practically in use, the development of GaAs MESFET analog integrated circuits is left behind. In this paper, two circuit techniques to improve the performance of GaAs MESFET analog circuits are provided. The one is to realize a high impedance active load circuit which dose not need CMFB (Common Mode Feed Back) to achieve stable DC biasing point. The other is to cancel the harmonic destortion caused by nonlinear characteristics of GaAs MESFETs. As an application example of the proposed circuits, biquad low-pass and band-pass filters are realized and simulated by HSPICE to verify the validity of the proposed method.

In recent years, and increasing number of studies have been reported regarding multimedia LANs that integrate voice, data and video communications. The Movable Boundary method has been suggested as a way to integrate circuit and packet switching. However, how this can be practically managed, especially for multimedia LANs, is not clear. Working under the assumption that an optical loop network in used as a multimedia LAN, we propose Hybrid Allocation as a new Movable Boundary method. Hybrid Allocation features traffic prediction for circuit switching calls, and timeslot allocation close to the boundary of circuit and packet switching areas. Evaluations of traffic simulation and network efficiency show it to be a promising architecture for integrating circuit and packet switching on a multimedia LAN.

Narrow-band ISDN services may experience nonstationary traffic conditions. Therefore, switch design should take account of these conditions. We propose new performance measures for switching systems and describe a traffic model, which is a mixture of stationary Poissonian traffic and momentarily focused traffic. On the basis of this model, performance measures are determined so as to satisfy grade of service requirements that are in effect during some short interval after the momentarily focused traffic enters the system. We also propose an overload control scheme that uses these new performance measures. Finally, we show practical and numerical examples for the performance measures and overload control scheme.

Partial capture effect for multi-carrier radio packet communication network is evaluated in frequency selective fading channel. In multi-carrier modulation (MCM) network where each terminal uses several sub-carriers for transmission,the terminals have different instantaneous frequency responses because of its location, fading pattern, and other various factors. This generates the difference of received power in frequency domain, then partial capture effect can be considered at each sub-carrier. Moreover these partially captured packets are not damaged by inter symbol interference (ISI) caused by frequency selective fading, which seriously degrades single-carrier modulation (SCM) network. From this point of view we present the partial capture effect for the MCM network in the frequency selective fading environment. The results show that the MCM network with partial capture has more advantages than the MCM network without partial capture in terms of the throughput and the average number of transmissions.

We propose a new network architecture nemed Holonic Network for personalized multimedia communications, which is characterized by distributed cooperative networking based on autonomous management and all-optical transport networks. We than propose autonomous routing method. Moreover, an information searching method and a route generation method with network maps, which are essential for this network, are proposed. Lastly, we evaluate the proposed network performance by theoretical analysis and system emulation.

In the information engineering learning environment, there may be more than one solution to any given problem. We have developed CAMELOT using the Nominal Group Technique for group problem solving. This paper describes the collaborative learning system on the Internet using discussion model, the effectiveness of collaborative learning in modeling the entity-relationship diagram within the field of information engineering, and how to apply AI technologies such as rule-based reasoning and case-based reasoning to the pedagogical strategy. By using CAMELOT, each learner learns how to analyze through case studies and how to collaborate with his or her group in problem solving. As a result. We have found evidence for the effectiveness of collaborative learning, such as getting a deeper understanding by using CAMELOT than by individual learning, because they can reach better solutions through discussion, tips from other learners, examination of one another's individual solutions, and understanding alternative solutions using case-based reasoning.

Photovoltaic devices capable of generating more than 200 volts with an area of 1 cm2 have been developed for directly driving microactuators such as piezoelectric or electrostatic actuators. The micro-devices interconnect 285 micro cells (unit cell size: about 0.5 mm 2.0 mm) in series, and have an open circuit voltage (Voc) of 207 volts, a short circuit current (Isc) of 36.6 µA, a maximum output power (Pmax) of 4.65 mW and a fill factor (F.F.) of 0.615 under AM (Air Mass) 1.5 and 100 mW/cm2 illumination. This voltage is the highest in the world for the area of 1 cm2. The series connection is precisely processed by a focused laser beam, thereby significantly reducing the area needed for device connections. It has been confirmed that a piezoelectric polymer can be directly driven by the electrical output in evaluating the potential of the devices to be used as a microactuator's power source.

The purpose of this study is to present results of forecast of ranges for yen to US dollar exchange rate fluctuation in order to evaluate the performance of two algorithms: the original backpropagation (OBP), which is the most widely used algorithm, and the second algorithm (NBP), which is a proposed modification to the first one by the authors. The set of data consisted of economic and financial values that have already been calculated by the Bank of Japan and the Japanese Ministry of Planning and Finance. This data was available though the Nikkei Data Service and stretched from January, 1986, to the end of December, 1992. The results obtained show not only that NBP performs better than OBP since the former speeds up convergence time to a given error value, but also NBP shows a good generalization performance.

A method is proposed for forming hillock-free aluminum-based alloy bus lines for active-matrix liquid-crystal displays (LCDs). Aluminum (Al)-based alloy films are deposited using an Al target containing boron (B) or nickel (Ni) in a sputtering ambient containing nitrogen. The Al-Ni films deposited using an Al target containing Ni showed excellent hillock resistance: virtually no hillock formation after thermal treatment at around 400 and no significant increase in resistivity. These films also showed good patternability with a simple wet etching: a smooth line edge and a gently tapered profile. These films are thus suitable for the bus lines of active matrices.

A low power dual modulus prescaler for frequency synthesizers has been designed in a standard 1.2 µm digital CMOS process using enhancement source coupled logic (ESCL). Being a differential low amplitude current mode logic, ESCL has two interesting characteristics for this design besides low power consumption: the low noise performance, that allows this circuit to be on the same chip with sensitive analog circuitry, and the ability to run with a 200 mV sinusoidal signal as generated from an LC oscillator without the need of a clock amplifier. At 195 MHz and 3 V supply, the current consumption of the prescaler is as low as 289 µA, while maximum operating frequencies of 910 MHz at 5 V and 650 MHz at 3 V are achieved.

Recently, torque-transmission one-way tip articulated fiberscopes with a working channel have been developed. With this type of scopes, force is transmitted from the operator's hands to the tip of the fiberscope to obtain an adequate field of view. Micro actuators are expected to increasingly replace the operator's hands. Shape memory alloy (SMA) coil spring actuators are well suited to this purpose because of their large displacement compared with conventional actuators. In the fabrication of SMA coil springs, we examined fabrication conditions such as the tension and pitch of the SMA wire. As a result, we have successfully fabricated coil springs with a minimum outer diameter of 76 µm. SMA wire 25 µm in diameter and stainless steel wire 30 µm in diameter were used. As an application using SMA actuators, an active fiberscope (using an image guide fiber with 4200 pixels and light guide fibers) 2 mm in outer diameter with SMA actuators was designed and fabricated. We investigated the mechanical properties of the bending part in designing the SMA actuators. The specifications of the SMA coil springs are determined by the displacement and the force required of the pull wire. The relationship between the displacement of the pull wire and the number of windings of the SMA coil spring was calculated. The effective number of windings of SMA coil spring was found to be seventeen when using wire of 0.3 mm in diameter. The tip of the fiberscope was bent approximately 60 degrees and returned to the straight position when a current was applied to each of the SMA coil springs. A clear picture of the fiberscope which followed the tip bending operation could be received on the monitor. This SMA actuator can be easily extended for bending in many directions by configuring several of these mechanisms.

A new magnetostrictive thin-film cantilever actuator and a new thin-film walking mechanism were developed. The actuators were made of magnetostrictive amorphous Tb-Fe and Sm-Fe thin films, deposited on the opposite sides of a polyimide film substrate. These actuators need not power supply cables because they were remotely driven by external magnetic fields. The static deflection of a 3-mm-long cantilever actuator was as large as 100 µm at 300 Oe field. Moreover the application of ac resonant frequency field of the same intensity yielded deflection of above 500 µm. The walking mechanism ran as fast as in the order of cm/s. The forward and backward running were possible depending on the frequency of applied magnetic field. Such unique characteristics suggest that magnetostrictive thin-film actuators are useful in MEMS applications.

A thermally controlled magnetization actuator (TCMA) is proposed for micro-mechanical relays. It is actuated by changing the local magnetization of the structure by remote heating using a laser beam. It is fabricated by nickel surface micromachining (a fabrication technique using nickel electroplating). The optical power of the laser diode used to drive the TCMA is about 30 mW. The switching time of the microrelay was experimentally measured to be 10 ms, the same as that of a conventional mechanical relay. The contact force was calculated to be 20 µN, which can be improved by increasing the size of the TCMA.

A method is presented for implementing a neural control system for controlling a piezopolymer bimorph flexible micro-actuator. Two neural controllers were constructed, both with an adaptive-type neural identifier and a learning-type direct or open-loop neural controller, focusing on the difference in learning speed between the adaptive and learning schemes. Simulated use of the proposed controllers to control a flexible micro-actuator showed that they can do so effectively. Experiments also demonstrated that a neural controller can be used to control a flexible micro-actuator.

Resonance characteristics of a coupled dielectric resonator which consists of a Whispering Gallery mode dielectric disk resonator and a ring resonator located eccentrically are analyzed. New analytical results of resonance characteristic based on the distributed coupling phenomena between the disk and the ring are obtained. The resonance performances have also been verified experimentally on X band model. We have found that Free Spectral Range of the coupled resonator is several times larger than that of the single disk resonator and the single ring resonator, respectively. As a result, the eccentric coupled resonator discussed in this paper can be used as a frequency selective element in millimeter wave integrated circuits.

It is necessery to investigate the buckling mechanism in order to obtaining good performance from various sensors composed of resistors and microbridges or membranes. Especially for flow sensors, a convex formed bridge has an advantage over a flat or concave bridge with respect to heat transfer coefficient. We have fabricated various shapes of bridges and have prepared SiNx sputtered films as the support films of microbridges and Pt sputtered or evaporated films as resistors. We have achieved deformation control for both the longitudinal axis and transverse axis of Pt/SiNx double layered microbridges by appropriate selection of the total residual stress of Pt/SiNx structures and of the stress gradient between the Pt film and SiNx film. The deformation direction of the longitudinal axis of bridges for the beam bridge (Type ) are all the same as that of cantilevers and may be predicted via the stress gradient between the Pt and SiNx filmes of the bridges. The deflection of the transverse axis of the table bridge supported by four beams (Type ) changes linearly with the total stress of the Pt/SiNx structure and the deformation changes for the transverse axis are the same as that of completely free films as predicted from the stress gradient between the Pt film and the SiNx film. The interesting result is that the deformation direction for the longitudinal axis of Type is opposite to that of Type with the same film structure. We discuss the reason for this opposition via differences in the progress of the anisotropic etching. We consider that this result will expand the range of manufacturable shapes and film structures of microbridges.