Impulsive noise interference is a significant problem for the Integrated Services Digital Broadcasting for Terrestrial (ISDB-T) receivers due to its effect on the orthogonal frequency division multiplexing (OFDM) signal. In this paper, an adaptive scheme to suppress the effect of impulsive noise is proposed. The impact of impulsive noise can be detected by using the guard band in the frequency domain; furthermore the position information of the impulsive noise, including burst duration, instantaneous power and arrived time, can be estimated as well. Then a time-domain window function with adaptive parameters, which are decided in terms of the estimated information of the impulsive noise and the carrier-to-noise ratio (CNR), is employed to suppress the impulsive interference. Simulation results confirm the validity of the proposed scheme, which improved the bit error rate (BER) performance for the ISDB-T receivers in both AWGN channel and Rayleigh fading channel.

Solution-based organic field-effect transistors (OFETs) with low parasitic capacitance have been fabricated using a self-aligned method. The self-aligned processes using a cross-linking polymer gate insulator allow fabricating electrically stable polymer OFETs with small overlap area between the source-drain electrodes and the gate electrode, whose frequency characteristics have been investigated by impedance spectroscopy (IS). The IS of polymer OFETs with self-aligned electrodes reveals frequency-dependent channel formation process and the frequency response in FET structure.

This paper proposes a single-carrier transmission method based on an overlap frequency-domain equalizing (FDE) and a coherent averaging. FDE is a block-based equalizing technique using discrete Fourier transform. A cyclic prefix is often used to avoid inter-block interference under multipath channel conditions, which reduces transmission efficiency. An overlap FDE is a technique to avoid the cyclic prefix insertion, but the residual interferences often exist after the FDE processing according to the channel conditions. The method proposed in this paper suppresses the residual interferences by applying a coherent averaging to the FDE outputs and improve the equalization performances. Computer simulation shows the effect of the proposed technique over the multipath channels.

In this letter, a novel physical layer signaling transmission scheme is proposed, where the signaling information is conveyed by a pair of training sequences located in the odd and even subcarriers of an orthogonal frequency division multiplexing (OFDM) training symbol. At the receiver side, only a single correlator is required to detect the signaling information. Computer simulations verify the proposed signaling could outperform the S1 signaling and achieve similar robustness as the S2 signaling of the DVB-T2 standard.

This paper presents the design and implementation of a quadrature voltage-controlled ring oscillator with the improved figure of merit (FOM) using the four single-ended inverter topology. Furthermore, a new architecture to prevent the latch-up in even number of stages composed of single-ended ring inverters is proposed. The design is implemented in 0.18 µm CMOS technology and the measurement results show a FOM of -163.8 dBc/Hz with the phase noise of -125.8 dBc/Hz at 4 MHz offset from the carrier frequency of 3.4 GHz. It exhibits a frequency tuning range from 1.23 GHz to 4.17 GHz with coarse and fine frequency tuning sensitivity of 1.08 MHz/mV and 120 kHz/mV, respectively.

Although unavailability and failure frequency are important reliability measures for designing telecommunications networks, having two different reliability measures causes difficulties when their evaluation results contradict each other. To overcome this difficulty, for determining a single reliability measure is proposed. Market share, which is an important management index, was used and the effect of each reliability measure on this index was studied. If we the effect of one of the reliability measures is small enough to be ignored, then the other one is chosen as the single reliability measure. The procedure of the proposed statistical analysis method and test results suggesting that failure frequency is promising as a single reliability measure are discussed.

In this paper, we propose a novel feeding structure for a coaxial-excited compact waveguide filter, which is composed of planar resonators called frequency-selective surfaces (FSSs). In our proposed feeding structure, new FSSs located at the input and output ports are directly excited by the coaxial line. By using the FSSs, the transition from the TEM mode to the TE10 mode is realized by the resonance of the FSSs. Therefore, the backshort length from the coaxial probe to the shorted waveguide end can be made much shorter than one-quarter of the guided wavelength. Additionally, the coaxial-excited FSS provides one transmission zero at each stopband. As a design example, a three-stage bandpass filter with 4% bandwidth at the X band is demonstrated. The designed filter has a very compact size of one cavity and has high skirt selectivity with six transmission zeros. The effectiveness of the design is confirmed by the comparison of frequency characteristics obtained by the simulation and measurement.

Broadband single-carrier frequency division multiple access (SC-FDMA) uplink using frequency-domain square-root Nyquist filtering is considered. The peak-to-average power ratio (PAPR) of filtered SC signals can be reduced by increasing the filter roll-off factor α. Furthermore, an additional frequency diversity gain can be obtained by making use of the excess bandwidth introduced by the transmit root Nyquist filtering. However, if the carrier-frequency separation is kept the same as in the case of α=0, the adjacent users' signal spectra overlap with the desired users' spectrum and the multiuser interference (MUI) is produced. In this paper, we propose two frequency-domain iterative MUI cancellation schemes which can achieve the frequency diversity gain through spectrum combining. The achievable bit error rate (BER) and throughput performances are evaluated by computer simulation.

Aassuming that the depolarization-induced noise generated in the dual-polarized channel is AWGN and spreads uniformly over the whole channel, we derive an effective XPD formula that can be used to estimate the depolarization effects for both partially and completely overlapped channels.

In orthogonal frequency division multiple access (OFD-MA) systems, soft frequency reuse (SFR) and distributed antenna system (DAS) are two effective techniques to avoid excessive inter-cell interference (ICI). To gain the advantages of both, in this letter, we build a new cell architecture by jointly taking DAS and SFR into consideration to achieve the goal of high and well-balanced capacity. Furthermore, to rectify the shortfall in the literature, the capacity and outage probability in the multi-cell environment are derived by taking the complete channel effects into account, including the path loss, shadowing and Rayleigh fading. Simulations verify the superior performance and exactness of the analytical results.

In this paper, a new method for 2-D frequency estimation of multiple damped sinusoids in additive white Gaussian noise is proposed. The key idea is to combine the subspace-based technique and projection separation approach. The frequency parameters in the first dimension are estimated by the MUSIC-based method, and then a set of projection separation matrices are constructed by the estimated frequency parameters. In doing so, the frequency parameters in the second dimension can be separated by the constructed projection separation matrix. Finally, each frequency parameter in the second dimension is estimated by multiple 1-D MUSIC-based methods. The estimated frequency parameters in two dimensions are automatically paired. Computer simulations are included to compare the proposed algorithm with several existing methods.

Some statistical characteristics, including the means and the cross-correlations, of frequency-selective Rician fading channels seen by orthogonal frequency division multiplexing (OFDM) subcarriers are derived in this paper. Based on a pairwise error probability analysis, the mean vector and the cross-correlation matrix are used to obtain an upper bound of the overall bit-error rate (BER) in a closed-form for coded OFDM signals with and without inter-carrier interference. In this paper, the overall BER is defined as the average BER of OFDM signals of all subcarriers obtained by considering their cross-correlations. Numerical examples are presented to compare the proposed upper bound of the overall BERs and the overall BERs obtained by simulations.

A 0.8-V CMOS Phase-Locked Loop (PLL) has been designed and fabricated by using a 0.13-µm 1p8m CMOS process. In the proposed PLL, the double-positive-feedbacks voltage-controlled oscillator (DPF-VCO) is used to generate current signals for the coupling current-mode injection-locked frequency divider (CCMILFD) and current-injection current-mode logic (CICML) divider. A short-pulsed-reset phase frequency detector (SPR-PFD) with the reduced pulse width of reset signal to improve the linear range of the PFD and a complementary-type charge pump to eliminate the current path delay are also adopted in the proposed PLL. The measured in-band phase noise of the fabricated PLL is -98 dBc/Hz. The locking range of the PLL is from 22.6 GHz to 23.3 GHz and the reference spur level is -69 dBm that is 54 dB bellow the carrier. The power consumption is 9.2 mW under a 0.8-V power supply. The proposed PLL has the advantages of low phase noise, low reference spur, and low power dissipation at low voltage operation.

This paper presents the development of a sound–specific vibration interface and its evaluation results by playing three commercial games with the interface. The proposed interface complements the pitfalls of existing frequency–based vibration interfaces such as vibrating headsets, mouses, and joysticks. Those interfaces may bring negative user experiences by generating incessant vibrations because they vibrate in response to certain sound frequencies. But the proposed interface which responds to only target sounds can improve user experiences effectively. The hardware and software parts of the interface are described; the structure and the implementation of a wrist pad that delivers vibration are discussed. Furthermore, we explain a sound-matching algorithm that extracts sound characteristics and a GUI-based pattern editor that helps users to design vibration patterns. The results from evaluating the performance show that the success ratio of the sound matching is over 90% at the volume of 20 dB and the delay time is around 400 msec. In the survey about user experiences, the users evaluates that the interface is more than four times effective in improving the reality of game playing than without using the vibration interfaces, and two times than the frequency–based ones.

A dual-band divide-by-2 quadrature injection-locked frequency divider (QILFD) is proposed to achieve high-speed, low power, wide-locking range, and accurate quadrature output phases. The QILFD consists of two dual-resonance differential voltage controlled oscillators and four coupling NMOS injectors in a ring configuration. The injectors are used as coupling devices of two differential ILFDs and are also used as common source amplifiers. The proposed QILFD has been implemented with the TSMC 90 nm CMOS technology and the core power consumption is 2.31 mW at the dc drain-source bias of 0.5 V. At the input power of 0 dBm, the low-band and high-band divide-by-2 operation ranges are respectively from 7.0 GHz to 10.1 GHz and 19.8 GHz to 24.6 GHz.

In this paper, we present an approach of detecting speech presence for which the decision rule is based on a combination of multiple features using a sigmoid function. A minimum classification error (MCE) training is used to update the weights adjustment for the combination. The features, consisting of three parameters: the ratio of ZCR, the spectral energy, and spectral entropy, are combined linearly with weights derived from the sub-band domain. First, the Bark-scale wavelet decomposition (BSWD) is used to split the input speech into 24 critical sub-bands. Next, the feature parameters are derived from the selected frequency sub-band to form robust voice feature parameters. In order to discard the seriously corrupted frequency sub-band, a strategy of adaptive frequency sub-band extraction (AFSE) dependant on the sub-band SNR is then applied to only the frequency sub-band used. Finally, these three feature parameters, which only consider the useful sub-band, are combined through a sigmoid type function incorporating optimal weights based on MSE training to detect either a speech present frame or a speech absent frame. Experimental results show that the performance of the proposed algorithm is superior to the standard methods such as G.729B and AMR2.

A novel divide-by-3 injection-locked frequency divider (ILFD) is proposed. The ILFD circuit is realized with a cross-coupled n-core MOS LC-tank oscillator embedded with a push-push signal generator and two injection MOSFETs for coupling the injection signal into the resonator. The ILFD uses the linear mixer to extend the locking range and has been implemented in a standard 0.18 µm CMOS process. The core power consumption of the ILFD core is 3.12 mW. The divider's free-running frequency is tunable from 4.26 GHz to 4.9 GHz by tuning the varactor's control bias, and at the incident power of 0 dBm the locking range of the ILFD used as a divide-by-3 divider is 1.5 GHz, from 12.5 GHz to 14.0 GHz.

We review our recent work on Yb-doped and hybrid-structured solid photonic bandgap fibers (Yb-HS-SPBGFs) for linearly-polarized fiber lasers oscillating in the small gain wavelength range from 1160 nm to 1200 nm. The stack-and-draw or pit-in-jacket method is employed to fabricate two Yb-HS-SPBGFs. Both of the fiber shows optical filtering property for eliminating ASE in the large gain wavelength range from 1030 nm to 1130 nm and enough high birefringence for maintaining linear polarization, thanks to the photonic bandgap effect and the induced birefringence of the hybrid structure. The fiber attenuation of the Yb-HS-SPBGF fabricated by the pit-in-jacket method is much lower than that of the Yb-HS-SPBGF fabricated by stack-and-draw method. Linearly-polarized single stage fiber lasers using Yb-HS-SPBGFs are also demonstrated. Laser oscillation at 1180 nm is confirmed without parasitic lasing in the fiber lasers. High output power and high slope efficiency in linearly-polarized single-cavity fiber laser using the low-loss Yb-HS-SPGF fabricated by the pit-in-jacket method are achieved. Narrow linewidth, high polarization extinction ratio and high beam quality are also confirmed, which are required for high-efficient frequency-doubling. A compact and high-power yellow-orange frequency-doubling laser would be realized by using a linearly-polarized single-cavity fiber laser employing a low-loss Yb-HS-SPBGF.

In this letter we present efficient iterative frequency domain equalization for single-carrier (SC) transmission systems with insufficient cyclic prefix (CP). Based on minimum mean square error (MMSE) criteria, iterative decision feedback frequency domain equalization (IDF-FDE) combined with cyclic prefix reconstruction (CPR) is derived to mitigate inter-symbol interference (ISI) and inter-carrier interference (ICI). Computer simulation results reveal that the proposed scheme significantly improves the performance of SC systems with insufficient CP compared with previous schemes.

Transmission performance of carrier superposed signals for frequency reuse are significantly degraded when transmitted through a satellite channel containing a nonlinear device. The extent to which the signals are degraded depends on the operating level (back off) of the transponder. This paper proposes a method to compensate for the effects of nonlinearity in the interference canceller by giving the same nonlinearity to a replica with the capability to automatically track the back off of the satellite transponder. Computer simulations show that the proposed technique significantly enhances system performance at all transponder operating levels even though it can be simply implemented in the canceller by digital signal processing circuits.