In this paper, an improved charge pump (CP) and a modified nonlinear phase frequency detector (PFD) are designed and fabricated in a 90-nm CMOS process. The CP is optimized with a combination of circuit techniques such as pedestal error cancel scheme to eliminate the charge injection and the other non-ideal characteristics. The nonlinear PFD is based on a modified circuit topology to enhance the acquisition capability of the PLL. The optimized CP and nonlinear PFD are integrated into a Ka-band PLL. The measured output current mismatch ratio of the improved CP is less than 1% when the output voltage Vout fluctuates between 0.2 to 1.1V from a 1.2V power supply. The measured phase error detection range of the modified nonlinear PFD is between -2π and 2π. Owing to the modified CP and PFD, the measured reference spur of the Ka-band PLL frequency synthesizer containing the optimized CP and PFD is only -56.409dBc at 30-GHz at the locked state.

Unmanned aerial vehicle mounted base stations (UAV-BSs) can provide wireless cellular service to ground users in a variety of scenarios. The efficient deployment of such UAV-BSs while optimizing the coverage area is one of the key challenges. We investigate the deployment of UAV-BS to maximize the coverage of ground users, and further analyzes the impact of the deployment of UAV-BS on the fairness of ground users. In this paper, we first calculated the location of the UAV-BS according to the QoS requirements of the ground users, and then the fairness of ground users is taken into account by calculating three different fairness indexes. The performance of two genetic algorithms, namely Standard Genetic Algorithm (SGA) and Multi-Population Genetic Algorithm (MPGA) are compared to solve the optimization problem of UAV-BS deployment. The simulations are presented showing that the performance of the two algorithms, and the fairness performance of the ground users is also given.

In the beam-type microwave power transmission system, it is required to minimize the interference with communication and the influence on the human body. Retrodirective system that re-radiates a beam in the direction of arrival of a signal is well known as a beam control technique for accurate microwave power transmission. In this paper, we newly propose to apply the retrodirective system to both transmitting and receiving antennas. The leakage to the outside of the system is expected to minimize self-convergently while following the atmospheric fluctuation and the antenna movement by repeating the retrodirective between the transmitting and receiving antenna in this system. We considered this phenomenon theoretically using an infinite array antenna model. Finally, it has been shown by the equivalent circuit simulation that stable transmission can be realized by oscillating the system.

It is generally believed that jamming signals similar to communication signals tend to demonstrate better jamming effects. We believe that the above conclusion only works in certain situations. To select the correct jamming scheme for a multi-level quadrature amplitude modulation (MQAM) signal in a complex environment, an optimal jamming method based on orthogonal decomposition (OD) is proposed. The method solves the jamming problem from the perspective of the in-phase dimension and quadrature dimension and exhibits a better jamming effect than normal methods. The method can construct various unconventional jamming schemes to cope with a complex environment and verify the existing jamming schemes. The Experimental results demonstrate that when the jammer ideally knows the received power at the receiver, the proposed method will always have the optimal jamming effects, and the constructed unconventional jamming scheme has an excellent jamming effect compared with normal schemes in the case of a constellation distortion.

This paper presents a hybrid architecture for a neural network (NN) trained by a particle swarm optimization (PSO) algorithm. The NN is implemented on the hardware side while the PSO is executed by a processor on the software side. In addition, principal component analysis (PCA) is also applied to reduce correlated information. The PCA module is implemented in hardware by the SystemVerilog programming language to increase operating speed. Experimental results showed that the proposed architecture had been successfully implemented. In addition, the hardware-based NN trained by PSO (NN-PSO) program was faster than the software-based NN trained by the PSO program. The proposed NN-PSO with PCA also obtained better recognition rates than the NN-PSO without-PCA.

Access control and surveillance applications like walking-through security gates and immigration control points have a great demand for convenient and accurate biometric recognition in unconstrained scenarios with low user cooperation. The periocular region, which is a relatively new biometric trait, has been attracting much attention for recognition of an individual in such scenarios. This paper proposes a periocular recognition method that combines Phase-Based Correspondence Matching (PB-CM) with a texture enhancement technique. PB-CM has demonstrated high recognition performance in other biometric traits, e.g., face, palmprint and finger-knuckle-print. However, a major limitation for periocular region is that the performance of PB-CM degrades when the periocular skin has poor texture. We address this problem by applying texture enhancement and found out that variance normalization of texture significantly improves the performance of periocular recognition using PB-CM. Experimental evaluation using three public databases demonstrates the advantage of the proposed method compared with conventional methods.

Phase interferometer using baseline composed by uniform linear array (ULA) with stable phase center for estimating the angle of arrival (AOA) is always employed in the direction finding (DF) system. However, the phase center of antenna element could vary with the incident angle, frequency, multipath and so on. To deal with these problems, a novel method is proposed in this paper to calibrate the phase center over ultra-wideband (UWB). Meanwhile, the restrictions of this method are discussed. Numerical simulations reveal that higher accuracy and larger unambiguous angle range can be obtained by the proposed method.

The Shortest Vector Problem (SVP) is one of the most important lattice problems in computer science and cryptography. The LLL lattice basis reduction algorithm runs in polynomial time and can compute an LLL-reduced basis that provably contains an approximate solution to the SVP. On the other hand, the LLL algorithm in practice tends to solve low-dimensional exact SVPs with high probability, i.e., >99.9%. Filling this theoretical-practical gap would lead to an understanding of the computational hardness of the SVP. In this paper, we try to fill the gap in 3,4 and 5 dimensions and obtain two results. First, we prove that given a 3,4 or 5-dimensional LLL-reduced basis, the shortest vector is one of the basis vectors or it is a limited integer linear combination of the basis vectors. In particular, we construct explicit representations of the shortest vector by using the LLL-reduced basis. Our analysis yields a necessary and sufficient condition for checking whether the output of the LLL algorithm contains the shortest vector or not. Second, we estimate the failure probability that a 3-dimensional random LLL-reduced basis does not contain the shortest vector. The upper bound seems rather tight by comparison with a Monte Carlo simulation.

Location-based forwarding is a key driver for location-based services. This paper designs forwarding information data structures for location-based forwarding in Internet Service Provider (ISP) scale networks based on Named Data Networking (NDN). Its important feature is a naming scheme which represents locations by leveraging space-filling curves.

Kakuro is a popular logic puzzle, in which a player fills in all empty squares with digits from 1 to 9 so that the sum of digits in each (horizontal or vertical) line is equal to a given number, called a clue, and digits in each line are all different. In 2016, Bultel, Dreier, Dumas, and Lafourcade proposed a physical zero-knowledge proof protocol for Kakuro using a deck of cards; their proposed protocol enables a prover to convince a verifier that the prover knows the solution of a Kakuro puzzle without revealing any information about the solution. One possible drawback of their protocol would be that the protocol is not perfectly extractable, implying that a prover who does not know the solution can convince a verifier with a small probability; therefore, one has to repeat the protocol to make such an error become negligible. In this paper, to overcome this, we design zero-knowledge proof protocols for Kakuro having perfect extractability property. Our improvement relies on the ideas behind the copy protocols in the field of card-based cryptography. By executing our protocols with a real deck of physical playing cards, humans can practically perform an efficient zero-knowledge proof of knowledge for Kakuro.

The consistent alignment of point clouds obtained from multiple scanning positions is a crucial step for many 3D modeling systems. This is especially true for environment modeling. In order to observe the full scene, a common approach is to rotate the scanning device around a rotation axis using a turntable. The final alignment of each frame data can be computed from the position and orientation of the rotation axis. However, in practice, the precise mounting of scanning devices is impossible. It is hard to locate the vertical support of the turntable and rotation axis on a common line, particularly for lower cost consumer hardware. Therefore the calibration of the rotation axis of the turntable is an important step for the 3D reconstruction. In this paper we propose a novel calibration method for the rotation axis of the turntable. With the proposed rotation axis calibration method, multiple 3D profiles of the target scene can be aligned precisely. In the experiments, three different evaluation approaches are used to evaluate the calibration accuracy of the rotation axis. The experimental results show that the proposed rotation axis calibration method can achieve a high accuracy.

The scale of scientific data generated by experimental facilities and simulations in high-performance computing facilities has been proliferating with the emergence of IoT-based big data. In many cases, this data must be transmitted rapidly and reliably to remote facilities for storage, analysis, or sharing, for the Internet of Things (IoT) applications. Simultaneously, IoT data can be verified using a checksum after the data has been written to the disk at the destination to ensure its integrity. However, this end-to-end integrity verification inevitably creates overheads (extra disk I/O and more computation). Thus, the overall data transfer time increases. In this article, we evaluate strategies to maximize the overlap between data transfer and checksum computation for astronomical observation data. Specifically, we examine file-level and block-level (with various block sizes) pipelining to overlap data transfer and checksum computation. We analyze these pipelining approaches in the context of GridFTP, a widely used protocol for scientific data transfers. Theoretical analysis and experiments are conducted to evaluate our methods. The results show that block-level pipelining is effective in maximizing the overlap mentioned above, and can improve the overall data transfer time with end-to-end integrity verification by up to 70% compared to the sequential execution of transfer and checksum, and by up to 60% compared to file-level pipelining.

We present a seven-bit multilayer true-time delay (TTD) circuit operating from 1 to 7GHz for wideband phased array antennas. By stacking advanced substrates with low dielectric loss, the TTD with PCB process is miniaturized and has low insertion loss. The signal vias with surrounding ground vias are designed to provide impedance matching throughout the band, allowing the overall group delay to be flat. The standard deviation of the TTD for all states is below 19ps, which is 1.87% of the maximum group delay. The maximum delay is 1016ps with resolution of 8ps. The implemented TTD is 36.6×19.4mm2 and consumes 0.65mW at 3.3V supply for all the delay states. The measured input/output return loss is better than 12.1dB for the band of 1-7GHz.

In-phase and quadrature-phase imbalance (IQI) at transceivers is one of the serious hardware impairments degrading system performance. In this paper, we study the overall performance of massive multi-user multi-input multi-output (MU-MIMO) systems with IQI at both the base station (BS) and user equipments (UEs), including the estimation of channel state information, required at the BS for the precoding design. We also adopt a widely-linear precoding based on the real-valued channel model to make better use of the image components of the received signal created by IQI. Of particular importance, we propose estimators of the real-valued channel and derive the closed-form expression of the achievable downlink rate. Both the analytical and simulation results show that IQI at the UEs limits the dowlink rate to finite ceilings even when an infinite number of BS antennas is available, and the results also prove that the widely-linear precoding based on the proposed channel estimation method can improve the overall performance of massive MU-MIMO systems with IQI.

In this paper, a high-frequency resolution Digital Frequency Discriminator (DFD) IC using a Time to Digital Converter (TDC) and an edge counter for Instantaneous Frequency Measurement (IFM) is proposed. In the proposed DFD, the TDC measures the time of the maximum periods of divided RF short pulse signals, and the edge counter counts the maximum number of periods of the signal. By measuring the multiple periods with the TDC and the edge counter, the proposed DFD improves the frequency resolution compared with that of the measuring one period because it is proportional to reciprocal of the measurement time of TDC. The DFD was fabricated using 0.18-um SiGe-BiCMOS. Frequency accuracy below 0.39MHz and frequency precision below 1.58 MHz-RMS were achieved during 50 ns detection time in 0.3 GHz to 5.5 GHz band with the temperature range from -40 to 85 degrees.

This paper proposes a new rule-based approach to automatic question generation. The proposed approach focuses on analysis of both syntactic and semantic structure of a sentence. Although the primary objective of the designed system is question generation from sentences, automatic evaluation results shows that, it also achieves great performance on reading comprehension datasets, which focus on question generation from paragraphs. Especially, with respect to METEOR metric, the designed system significantly outperforms all other systems in automatic evaluation. As for human evaluation, the designed system exhibits similar performance by generating the most natural (human-like) questions.

This paper presents a type-I digital ring-based PLL with wide loop bandwidth to lower the ring oscillator's noise contribution. The loop delay due to the D flip-flops at filter's output is compensated in order to lower the noise peak and stably achieve wide loop bandwidth. The input-referred jitter is lowered by using a successive-approximated-register analog-to-digital converter (SAR-ADC)-based sampling phase detector (SPD). A stacked reference buffer is introduced to reduce the transient short-circuit current for low power and low reference spur. The locking issue due to the steady-state phase error in a type-I PLL and the limited range of the phase detector is addressed using a TDC-assisted loop. The loop stability and phase noise are analyzed, suggesting a trade-off for the minimum jitter. The solutions in detail are described. The prototype PLL fabricated in 65 nm CMOS demonstrates 2.0 ps RMS jitter, 3.1 mW power consumption, and 0.067 mm2 area, with 50 MHz reference frequency and 2.0 GHz output frequency.

Ring voltage-controlled-oscillators (VCOs) are increasingly being used to design ΔΣ ADCs. They have the merits of simple, highly digital and low-voltage tolerant, making them attractive alternatives for the classic scaling-unfriendly operational-amplifier-based methodology. This paper aims to provide a summary on the advancement of VCO-based ΔΣ ADCs. The scope of this paper includes the basics and motivations behind the VCO-based ADCs, followed by a survey covering a wide range of architectures and circuit techniques in both continuous-time (CT) and discrete-time (DT) implementation, and will discuss the key insights behind the contributions and drawbacks of these architectures.

This paper proposes a pulse-tail-feedback VCO, in which the tail transistor is driven using pulse-shaped voltage signals with rail-to-rail swing. The proposed pulse-tail-feedback (PTFB) VCO relies on reducing the current conduction period of the tail transistor and operating the tail transistors in triode region for reducing the flicker and thermal noise from the active elements. Mathematical analysis and circuit level simulations of the phase noise mechanism in the proposed PTFB-VCO is also presented in this paper for validating the effectiveness of the proposed technique. A prototype LC-VCO with the proposed PTFB technique is fabricated in a standard 180nm CMOS. Laboratory measurement shows a power consumption of 1.35mW from a 1.2V supply at 4.6GHz. The proposed PTFB-VCO achieves a flicker corner of 700Hz, which enables the VCO to maintain a fairly constant figure-of-merit (FoM) of -195dB within a wide offset frequency range of 1kHz-10MHz.

Over the past several years, the research of micro-expression recognition (MER) has become an active topic in affective computing and computer vision because of its potential value in many application fields, e.g., lie detection. However, most previous works assumed an ideal scenario that both training and testing samples belong to the same micro-expression database, which is easily broken in practice. In this letter, we hence consider a more challenging scenario that the training and testing samples come from different micro-expression databases and investigated unsupervised cross-database MER in which the source database is labeled while the label information of target database is entirely unseen. To solve this interesting problem, we propose an effective method called target-adapted least-squares regression (TALSR). The basic idea of TALSR is to learn a regression coefficient matrix based on the source samples and their provided label information and also enable this learned regression coefficient matrix to suit the target micro-expression database. We are thus able to use the learned regression coefficient matrix to predict the micro-expression categories of the target micro-expression samples. Extensive experiments on CASME II and SMIC micro-expression databases are conducted to evaluate the proposed TALSR. The experimental results show that our TALSR has better performance than lots of recent well-performing domain adaptation methods in dealing with unsupervised cross-database MER tasks.