A quantitative study is made on performance of neutron penumbral imaging with a toroidal-segment aperture, and it focused on isoplanaticity of aperture point spread function and effect of the non-isoplanaticity on the reconstructed images. The results show that the aperture point spread function is satisfactorily isoplanatic for a small field of view, while for a large field of view the point spread function is not satisfactorily isoplanatic resulting in some distortion in the reconstructed image and reduction of resolution.

The dispersion characteristics of two nonidentical coupled microstrip lines and N identical coupled microstrip lines are analyzed using the coupled-mode theory combined with Galerkin's moment method in spectral domain. In this approach, the solutions to the original coupled microstrips are approximated by a linear combination of eigenmode solutions associated with the isolated single microstrip, and the reciprocity relation is used to derive the coupled-mode equations. The coupling coefficients are given by the simple overlap integrals in spectral domain between the eigenmode fields and currents of the individual microstrips. It is shown that the numerical results are in very good agreement with those obtained by the direct Galerkin's moment method over a broad range of weak to moderately strong coupling.

We propose an nn optical switch that is suitable for flexible and reliable optical access networks and for reconfigurable optical inter-module connections in large-scale processing systems. The switch consists of an intersecting waveguide matrix, matching oil, and microactuators. Switching is based on the movement of oil due to capillary pressure, which is controlled by the microactuator. The necessary switching conditions were calculated and the results showed that both the oil volume and the microactuator position must be controlled. A trial optical switch was fabricated to test the switching principle, and switching and self-holding were both confirmed. These results show the feasibility of a very small self-holding nn optical switch that uses a waveguide matrix and microactuators made by using microfabrication technologies.

Force curves obtained from an elastic contact theory are shown and compared with experimental results. In the elastic contact theory, a pin-on-disk contact is assumed and the following interaction are taken into consideration; (i) elastic deformation, (ii) the specific energy of adhesion in the area of the contact, which is expressed as the difference between the surface energies and the interface energy, (iii) the long-range interaction outside the area of contact, assuming the additivity of the Lennard-Jones type potential, and (iv) another elastic term for the measurement system such as the cantilever stiffness of an atomic force microscope (AFM). In the limit when the stiffness is infinite, the theory conforms to Muller-Yushchenko-Derjaguin (MYD) theory. In the limit when the surface-surface interaction is negligible, the theory conforms to the analytical theory by Takahashi-Mizuno-Onzawa. In the limit when the stiffness is infinite and the long-range interaction outside the area of contact is negligible, the theory conforms to Johnson-Kendall-Roberts (JKR) theory. All parameters and all equations are normalized and the normalized force curve is obtained as the functional of only two parameters; (1) the normalized stiffness of the measurement system, and (2) the normalized distance which is used in the expression of the Lennard-Jones potential. The force-displacement plots are converted into force-penetration plots.

This paper describes the fabrication of micro-pipes and their applications to splicing parts and optical switches using single-mode fibers. Micro-pipes having almost the same inner diameter of bare fiber (125 µm) and lengths of around 5 mm are successfully mass-produced by using micromachining technology. We fabricate various kinds of metal pipes such as Au, Cu, Ni, and an FeNi alloy by selecting the appropriate electro-plating bath. We use an Au micro-pipe having a small slitted portion running along its axis (slitted micro-pipe) to splice single-mode fibers. We also use an FeNi alloy micro-pipe to construct a single-mode fiber switch. These new single-mode fiber devices employing micro-pipes show excellent optical and mechanical characteristics. Splicing losses are in the range of 0.2-0.4 dB. The developed 1 2 latching type single-mode fiber switches exhibit a low insertion loss of 0.35 dB, a minimum switching speed of 2 ms with a driving power of 9 mW, and stable operation for more than 108 switchings without damage. A practical application of the developed switch for testing optical devices is also demonstrated.

In this paper, two types of improved CMRR CMOS OAs, N type and P type, without common-mode feedback and the cascode current mirrors, are proposed. The CMRR of proposed OAs are enhanced by compensating variations in tail bias current, caused by a common mode input signal, at the differential input stage, by means of feedforward controlled current source. Simulation results show that the CMRR of the proposed OAs are 20dB higher than that of conventional OAs.

A method is proposed for forming hillock-free aluminum-based alloy bus lines for active-matrix liquid-crystal displays (LCDs). Aluminum (Al)-based alloy films are deposited using an Al target containing boron (B) or nickel (Ni) in a sputtering ambient containing nitrogen. The Al-Ni films deposited using an Al target containing Ni showed excellent hillock resistance: virtually no hillock formation after thermal treatment at around 400 and no significant increase in resistivity. These films also showed good patternability with a simple wet etching: a smooth line edge and a gently tapered profile. These films are thus suitable for the bus lines of active matrices.

It is necessery to investigate the buckling mechanism in order to obtaining good performance from various sensors composed of resistors and microbridges or membranes. Especially for flow sensors, a convex formed bridge has an advantage over a flat or concave bridge with respect to heat transfer coefficient. We have fabricated various shapes of bridges and have prepared SiNx sputtered films as the support films of microbridges and Pt sputtered or evaporated films as resistors. We have achieved deformation control for both the longitudinal axis and transverse axis of Pt/SiNx double layered microbridges by appropriate selection of the total residual stress of Pt/SiNx structures and of the stress gradient between the Pt film and SiNx film. The deformation direction of the longitudinal axis of bridges for the beam bridge (Type ) are all the same as that of cantilevers and may be predicted via the stress gradient between the Pt and SiNx filmes of the bridges. The deflection of the transverse axis of the table bridge supported by four beams (Type ) changes linearly with the total stress of the Pt/SiNx structure and the deformation changes for the transverse axis are the same as that of completely free films as predicted from the stress gradient between the Pt film and the SiNx film. The interesting result is that the deformation direction for the longitudinal axis of Type is opposite to that of Type with the same film structure. We discuss the reason for this opposition via differences in the progress of the anisotropic etching. We consider that this result will expand the range of manufacturable shapes and film structures of microbridges.

Recently, torque-transmission one-way tip articulated fiberscopes with a working channel have been developed. With this type of scopes, force is transmitted from the operator's hands to the tip of the fiberscope to obtain an adequate field of view. Micro actuators are expected to increasingly replace the operator's hands. Shape memory alloy (SMA) coil spring actuators are well suited to this purpose because of their large displacement compared with conventional actuators. In the fabrication of SMA coil springs, we examined fabrication conditions such as the tension and pitch of the SMA wire. As a result, we have successfully fabricated coil springs with a minimum outer diameter of 76 µm. SMA wire 25 µm in diameter and stainless steel wire 30 µm in diameter were used. As an application using SMA actuators, an active fiberscope (using an image guide fiber with 4200 pixels and light guide fibers) 2 mm in outer diameter with SMA actuators was designed and fabricated. We investigated the mechanical properties of the bending part in designing the SMA actuators. The specifications of the SMA coil springs are determined by the displacement and the force required of the pull wire. The relationship between the displacement of the pull wire and the number of windings of the SMA coil spring was calculated. The effective number of windings of SMA coil spring was found to be seventeen when using wire of 0.3 mm in diameter. The tip of the fiberscope was bent approximately 60 degrees and returned to the straight position when a current was applied to each of the SMA coil springs. A clear picture of the fiberscope which followed the tip bending operation could be received on the monitor. This SMA actuator can be easily extended for bending in many directions by configuring several of these mechanisms.

A new magnetostrictive thin-film cantilever actuator and a new thin-film walking mechanism were developed. The actuators were made of magnetostrictive amorphous Tb-Fe and Sm-Fe thin films, deposited on the opposite sides of a polyimide film substrate. These actuators need not power supply cables because they were remotely driven by external magnetic fields. The static deflection of a 3-mm-long cantilever actuator was as large as 100 µm at 300 Oe field. Moreover the application of ac resonant frequency field of the same intensity yielded deflection of above 500 µm. The walking mechanism ran as fast as in the order of cm/s. The forward and backward running were possible depending on the frequency of applied magnetic field. Such unique characteristics suggest that magnetostrictive thin-film actuators are useful in MEMS applications.

A method is presented for implementing a neural control system for controlling a piezopolymer bimorph flexible micro-actuator. Two neural controllers were constructed, both with an adaptive-type neural identifier and a learning-type direct or open-loop neural controller, focusing on the difference in learning speed between the adaptive and learning schemes. Simulated use of the proposed controllers to control a flexible micro-actuator showed that they can do so effectively. Experiments also demonstrated that a neural controller can be used to control a flexible micro-actuator.

Resonance characteristics of a coupled dielectric resonator which consists of a Whispering Gallery mode dielectric disk resonator and a ring resonator located eccentrically are analyzed. New analytical results of resonance characteristic based on the distributed coupling phenomena between the disk and the ring are obtained. The resonance performances have also been verified experimentally on X band model. We have found that Free Spectral Range of the coupled resonator is several times larger than that of the single disk resonator and the single ring resonator, respectively. As a result, the eccentric coupled resonator discussed in this paper can be used as a frequency selective element in millimeter wave integrated circuits.

This paper presents algorithms for computing the Minkowski sum of two polygons P and Q for a family of problems. For P being convex and Q being monotone, an algorithm is given with O (nm) time and space complexity. For both P and Q being monotone polygons, an O (nm log nm) time algorithm is presented and it is shown that the complexity of the sum is Θ (nmα(min(n,m))) in the worst case, where α() is the inverse of Ackermann's function. Finally, an O ((nm+k)log nm) time complexity algorithm is given when P is monotone and Q is simple, where k in the worst case could be Θ(n2m). The complexity of P Q is shown to be Θ(n2m) in the worst case. Here, m and n denote the number of edges of P and Q, respectively.

We show that the truth of a prenex normal form Presburger sentence bounded only by existential quantifiers (or an EPP-sentence) involving two variables can be decided in deterministic polynomial time. Specifically, an upper bound of the computation for the decision is O(n3u), where n is the number of atoms of the EPP-sentence, and u is the largest absolute value of all coefficients in the EPP-sentence. In the analysis for the upper bound, the random access machine is assumed for the machine model. Additionally, a uniform cost criterion is assumed. Deciding the truth of an EPP-sentence is an NP-complete problem, when the number of variables is not fixed. Furthermore, whether the truth of an EPP-sentence involving two or more variables can be decided in deterministic polynomial time, when the number of variables is fixed, or not has remained an open problem. We previously proposed a procedure for quickly deciding the truth of an EPP-sentence on the basis of a suggestion by D.C.Cooper. We found the upper bound by analyzing the decision procedure. The procedure can be applied to both automated correctness proof of specification in various design fields and detection of infeasible paths in a program. In the procedure, a matrix denoting coefficients of the variables in the EPP-sentence is triangulated.

Many efforts are currently underway to design wideband mobile communication systems. In this letter, we clarify the received signal level characteristics for wideband mobile radio channels in line-of-sight (LOS) microcells. We conduct several urban-area field experiments to measure the received signal levels for various receiver bandwidths from 300 kHz to 30 MHz and the power delay profile. The experimental results show that the fading depth of the received signal decreases as the normalized rms delay spread, defined as the product of receiver bandwidth and rms delay spread, increases. These results are useful in designing wideband microcell systems for urban areas.

Built-in self-test (BIST) has been applied to test an analog to digital converter (ADC) and a digital to analog converter (DAC) embedded in a DSP-core ASIC. The eight performance characteristics of the ADC and the DAC designed in accordance with the ITU-T recommendations are measured using the BIST. Three of the eight characteristics - the attenuation/frequency distortion, the variation of gain with input level, and the signal-to-total distortion - have been evaluated and the measured results have shown good agreement with measured results by conventional tests. In the BIST operation, the DSP-core generates input stimulus and analyzes output response by control of the self-test program, The sizes of the self-test program and coefficient data are 822 words of the IROM and 384 words of the data ROM, respectively. This area overhead is less than 0.5% of total chip area. Test-time by the BIST is reduced to approximately 3.2 seconds, which is one-tenth that of conventional testing. The mixed-signal DSP-core ASIC is testable with only logic test equipment, and as a result, test-cost - that is test investment and test-time - is reduced compared with conventional test methods.

Various approaches to reduce access network cost are discussed with emphasis on system and component technologies. On-going access network opticalization subjects are discussed with respect to PDS-based access systems.

The convergence characteristics of the adaptive beamformer with the RLS algorithm are analyzed in this paper. In case of the RLS adaptive beamformer, the convergence characteristics are significantly affected by the spatial characteristics of the signals/noises in the environment. The purpose of this paper is to show how these physical parameters affect the convergence characteristics. In this paper, a typical environment where a few directional noises are accompanied by background noise is assumed, and the influence of each component of the environment is analyzed separately using rank analysis of the correlation matrix. For directional components, the convergence speed is faster for a smaller number of noise sources since the effective rank of the input correlation matrix is reduced. In the presence of background noise, the convergence speed is slowed down due to the increase of the effective rank. However, the convergence speed can be improved by controlling the initial matrix of the RLS algorithm. The latter section of this paper focuses on the physical interpretation of this initial matrix, in an attempt to elucidate the mechanism of the convergence characterisitics.

Narrow-beam and low threshold current characteristics have been realized for a 1.3 µm FS-BH (Facet Selective growth Buried Heterostructure) laser diode monolithically integrated with a tapered waveguide lens by a selective area epitaxial growth technique. The beam divergences in the perpendicular and horizontal directions have been reduced down to about 12. By the introduction of the strained quantum well structure and the optimized cavity structure, the threshold current has been kept as low as 6 mA which is comparable to the conventional Fabry-Perot laser diodes. Even at high temperature as high as 85, the threshold current and the operation current (P=10 mW) have been suppressed to as low as 23 mA and 63 mA, respectively. Furthermore error-floor-free characteristics for 622 Mbps-50 km transmission have been confirmed under severe optical feedback condition.

Recently two interesting conjectures on the linear complexity of binary complementary sequences of length 2nN0 were given by Karkkainen and Leppanen when those sequences are considered as periodic sequences with period 2nN0, where those sequences are constructed by successive concatenations or successive interleavings from a pair of kernel complementary sequences of length N0. Their conjectures were derived from numerical examples and suggest that those sequences have very large linear complexities. In this paper we give the exact formula of characteristic polynomials for those complementary sequences and show that their conjectures are true.