In this letter, an efficient hybrid direction-of-arrival (DOA) estimation scheme is devised for massive uniform rectangular array. In this scheme, the DOA estimator based on a two-dimensional (2D) discrete Fourier transform is first applied to acquire coarse initial DOA estimates for single data snapshot. Then, the fine DOA is accurately estimated through using the iterative search estimator within a very small region. Meanwhile, a Nyström-based method is utilized to correctly compute the required noise-subspace projection matrix, avoiding the direct computation of full-dimensional sample correlation matrix and its eigenvalue decomposition. Therefore, the proposed scheme not only can estimate DOA, but also save computational cost, especially in massive antenna arrays scenarios. Simulation results are included to demonstrate the effectiveness of the proposed hybrid estimate scheme.

In this paper, the influence of high-temperature sputtering on the nitrogen-doped (N-doped) LaB6 thin film formation utilizing RF sputtering was investigated. The N-doped LaB6/SiO2/p-Si(100) MOS diode and N-doped LaB6/p-Si(100) of Schottky diode were fabricated. A 30 nm thick N-doped LaB6 thin film was deposited from room temperature (RT) to 150°C. It was found that the resistivity was decreased from 1.5 mΩcm to 0.8 mΩcm by increasing deposition temperature from RT to 150°C. The variation of work function was significantly decreased in case that N-doped LaB6 thin film deposited at 150°C. Furthermore, Schottky characteristic was observed by increasing deposition temperature to 150°C. In addition, the crystallinity of N-doped LaB6 thin film was improved by increasing deposition temperature.

This work reports a new technique to suppress the undesirable multiple-triggering effect in the typical diode triggered silicon controlled rectifier (DTSCR), which is frequently used as an ESD protection element in the advanced CMOS technologies. The technique is featured by inserting additional N-Well areas under the N+ region of intrinsic SCR, which helps to improve the substrate resistance. As a consequence, the delay of intrinsic SCR is reduced as the required triggering current is largely decreased and multiple-triggering related higher trigger voltage is removed. The novel DTSCR structures can alter the stacked diodes to achieve the precise trigger voltage to meet different ESD protection requirements. All explored DTSCR structures are fabricated in a 65-nm CMOS process. Transmission-line-pulsing (TLP) and Very-Fast-Transmission-line-pulsing (VF-TLP) test systems are adopted to confirm the validity of this technique and the test results accord well with our analysis.

Linear feed-forward/feedback shift registers are used as an effective tool of testing circuits in various fields including built-in self-test and secure scan design. In this paper, we consider the issue of testing linear feed-forward/feedback shift registers themselves. To test linear feed-forward/feedback shift registers, it is necessary to generate a test sequence for each register. We first present an experimental result such that a commercial ATPG (automatic test pattern generator) cannot always generate a test sequence with high fault coverage even for 64-stage linear feed-forward/feedback shift registers. We then show that there exists a universal test sequence with 100% of fault coverage for the class of linear feed-forward/feedback shift registers so that no test generation is required, i.e., the cost of test generation is zero. We prove the existence theorem of universal test sequences for the class of linear feed-forward/feedback shift registers.

The increase in network traffic in recent years has led to increased power consumption. Accordingly, many studies have tried to reduce the energy consumption of network devices. Various types of data have become available in large quantities via large high-speed computer networks. Time-constrained file transfer is receiving much attention as an advanced service. In this model, a request must be completed within a user-specified deadline or rejected if the requested deadline cannot be met. Some bandwidth assignment and routing methods to accept more requests have been proposed. However, these existing methods do not consider energy consumption. Herein, we propose a joint bandwidth assignment and routing method that reduces energy consumption for time-constrained large file transfer. The bandwidth assignment method reduces the power consumption of mediate node, typically router, by waiting for requests and transferring several requests at the same time. The routing method reduces the power consumption by selecting the path with the least predicted energy consumption. Finally, we evaluate the proposed method through simulation experiments.

In partially depleted SOI (PD-SOI) technology, the SCR-based protection device is desired due to its relatively high robustness, but be restricted to use because of its inherent low holding voltage (Vh) and high triggering voltage (Vt1). In this paper, the body-tie side triggering diode inserting silicon controlled rectifier (BSTDISCR) is proposed and verified in 180 nm PD-SOI technology. Compared to the other devices in the same process and other related works, the BSTDISCR presents as a robust and latchup-immune PD-SOI ESD protection device, with appropriate Vt1 of 6.3 V, high Vh of 4.2 V, high normalized second breakdown current (It2), which indicates the ESD protection robustness, of 13.3 mA/µm, low normalized parasitic capacitance of 0.74 fF/µm.

For the RF power amplifier, its exposed input and output are susceptible to damage from Electrostatic (ESD) damage. The bi-direction protection is required at the input in push-pull operating mode. In this paper, considering the process compatibility to the power amplifier, cascaded Grounded-gate NMOS (ggNMOS) and Polysilicon diodes (PDIO) are stacked together to form an ESD clamp with forward and reverse protection. Through Transmission line pulse (TLP) and CV measurements, the clamp is demonstrated as latch-up immune and low parasitic capacitance bi-direction ESD protection, with 18.67/17.34V holding voltage (Vhold), 4.6/3.2kV ESD protection voltage (VESD), 0.401/0.415pF parasitic capacitance (CESD) on forward and reverse direction, respectively.

In this paper, we propose an effective and robust method of spatial feature extraction for acoustic scene analysis utilizing partially synchronized and/or closely located distributed microphones. In the proposed method, a new cepstrum feature utilizing a graph-based basis transformation to extract spatial information from distributed microphones, while taking into account whether any pairs of microphones are synchronized and/or closely located, is introduced. Specifically, in the proposed graph-based cepstrum, the log-amplitude of a multichannel observation is converted to a feature vector utilizing the inverse graph Fourier transform, which is a method of basis transformation of a signal on a graph. Results of experiments using real environmental sounds show that the proposed graph-based cepstrum robustly extracts spatial information with consideration of the microphone connections. Moreover, the results indicate that the proposed method more robustly classifies acoustic scenes than conventional spatial features when the observed sounds have a large synchronization mismatch between partially synchronized microphone groups.

We propose an auxiliary-noise power-scheduling method for a pre-inverse active noise control (PIANC) system. Conventional methods cannot reduce the power of auxiliary-noise due to the use of the filtered-x least mean square (FxLMS) algorithm. We developed our power-scheduling method for a PIANC system to solve this problem. Since a PIANC system uses a delayed input signal for a control filter, the proposed method delivers stability even if the acoustic path fluctuates. The proposed method also controls the gain of the auxiliary-noise based on the secondary-path-modeling state. The proposed method determines this state by the variation in the power of the secondary-path-modeling-error signal. Thus, the proposed method changes the power-scheduling of the auxiliary-noise. When the adaptive algorithm does not sufficiently converge, the proposed method injects auxiliary-noise. However, auxiliary-noise stops when the adaptive algorithm sufficiently converges. Therefore, the proposed method improves noise reduction performance.

Wireless networked control systems (WNCSs) are control systems whose components are connected through wireless networks. In WNCSs, a controlled object (CO) could become unstable due to bursty packet losses in addition to random packet losses and round-trip delays on wireless networks. In this paper, to reduce these network-induced effects, we propose a new design for multihop TDMA-based WNCSs with two-disjoint-path switching, where two disjoint paths are established between a controller and a CO, and they are switched if bursty packet losses are detected. In this system, we face the following two difficulties: (i) link scheduling in TDMA should be done in such a way that two paths can be switched without rescheduling, taking into account of the constraint of control systems. (ii) the conventional cross-layer design method of control systems is not directly applicable because round-trip delays may vary according to the path being used. Therefore, to overcome the difficulties raised by the two-path approach, we reformulate link scheduling in multihop TDMA and cross-layer design for control systems. Simulation results confirm that the proposed WNCS achieves better performance in terms of the 2-norm of CO's states.

This paper analyzes and compares two methods to estimate electromagnetically coupled noises introduced to an antenna due to the nearby circuits at a circuit design stage. One of them is to estimate the power spectrum, and the other one is to estimate the active S11 parameter at the victim antenna, respectively, and both of them use simulated standard S-parameters for the electromagnetic coupling in the circuit. They also need the assumed or measured excitation of noise sources. To confirm the validness of the two methods, an evaluation board consisting of an antenna and noise sources were designed and fabricated in which voltage controlled oscillator (VCO) chips are placed as noise sources. The generated electromagnetic noises are transferred to an antenna via loop-shaped transmission lines, degrading the performance of the antenna. In this paper, detailed analysis procedures are described using the evaluation board, and it is shown that the two methods are equivalent to each other in terms of the induced voltages in the antenna. Finally, a procedure to estimate antenna performance degradation at the design stage is summarized.

Here, we present a novel spectroscopic imaging method based on the boundary-extraction scheme for wide-beam terahertz (THz) three-dimensional imaging. Optical-lens-focusing systems for THz subsurface imaging generally require the depth of the object from the surface to be input beforehand to achieve the desired azimuth resolution. This limitation can be alleviated by incorporating a wide-beam THz transmitter into the synthetic aperture to automatically change the focusing depth in the post-signal processing. The range point migration (RPM) method has been demonstrated to have significant advantages in terms of imaging accuracy over the synthetic-aperture method. Moreover, in the RPM scheme, spectroscopic information can be easily associated with each scattering center. Thus, we propose an RPM-based terahertz spectroscopic imaging method. The finite-difference time-domain-based numerical analysis shows that the proposed algorithm provides accurate target boundary imaging associated with each frequency-dependent characteristic.

Three-dimensional (3D) reconstruction and scene depth estimation from 2-dimensional (2D) images are major tasks in computer vision. However, using conventional 3D reconstruction techniques gets challenging in participating media such as murky water, fog, or smoke. We have developed a method that uses a continuous-wave time-of-flight (ToF) camera to estimate an object region and depth in participating media simultaneously. The scattered light observed by the camera is saturated, so it does not depend on the scene depth. In addition, received signals bouncing off distant points are negligible due to light attenuation, and thus the observation of such a point contains only a scattering component. These phenomena enable us to estimate the scattering component in an object region from a background that only contains the scattering component. The problem is formulated as robust estimation where the object region is regarded as outliers, and it enables the simultaneous estimation of an object region and depth on the basis of an iteratively reweighted least squares (IRLS) optimization scheme. We demonstrate the effectiveness of the proposed method using captured images from a ToF camera in real foggy scenes and evaluate the applicability with synthesized data.

In this paper, we describe a novel low-delay 4K 120-fps real-time HEVC decoder with a parallel processing architecture that conforms to the HEVC main 4:2:2 10 profile. It supports the hierarchical temporal scalable streams required for Ultra High Definition high-frame-rate broadcasting and also supports low-delay and high-bitrate decoding for video transmission uses. To achieve this support, the decoding processes are parallelized and pipelined at the frame level, slice level, and coding tree unit row level. The proposed decoder was implemented on three FPGAs operated at 133 and 150 MHz, and it achieved 300-Mbps stream decoding and 37-msec end-to-end delay with our concurrently developed 4K 120-fps encoder.

Near real-time periodic tasks, which are popular in multimedia streaming applications, have deadline periods that are longer than the input intervals thanks to buffering. For such applications, the conventional frame-based schedulings cannot realize the optimal scheduling due to their shortsighted deadline assumptions. To realize globally energy-efficient executions of these applications, we propose a novel task scheduling algorithm, which takes advantage of the long deadline period. We confirm our approach can take advantage of the longer deadline period and reduce the average power consumption by up to 18%.

In this work, we present one novel rust detection method based upon one-class classification and L2 sparse representation (SR) with decision fusion. Firstly, a new color contrast descriptor is proposed for extracting the rust features of steel structure images. Considering that the patterns of rust features are more simplified than those of non-rust ones, one-class support vector machine (SVM) classifier and L2 SR classifier are designed with these rust image features, respectively. After that, a multiplicative fusion rule is advocated for combining the one-class SVM and L2 SR modules, thereby achieving more accurate rust detecting results. In the experiments, we conduct numerous experiments, and when compared with other developed rust detectors, the presented method can offer better rust detecting performances.

A method to reconstruct the surface shape of a scatterer from the relative intensity of the scattered field is proposed. Reconstruction of the scatterer shape has been studied as an inverse problem. An approach that employs boundary-integral equations can determine the scatterer shape with low computation resources and high accuracy. In this method, the reconstruction process is performed so that the error between the measured far field of the sample and the computed far field of the estimated scatterer shape is minimized. The amplitude of the incident wave at the sample is required to compute the scattered field of the estimated shape. However, measurement of the incident wave at the sample (measurement without the sample) is inconvenient, particularly when the output power of the wave source is temporally unstable. In this study, we improve the reconstruction method with boundary-integral equations for practical use and expandability to various types of samples. First, we propose new boundary-integral equations that can reconstruct the sample shape from the relative intensity at a finite distance. The relative intensity is independent from the amplitude of the incident wave, and the reconstruction process can be performed without measuring the incident field. Second, the boundary integral equation for reconstruction is discretized with boundary elements. The boundary elements can flexibly discretize various shapes of samples, and this approach can be applied to various inverse scattering problems. In this paper, we present a few reconstruction processes in numerical simulations. Then, we discuss the reason for slow-convergence conditions and introduce a weighting coefficient to accelerate the convergence. The weighting coefficient depends on the distance between the sample and the observation points. Finally, we derive a formula to obtain an optimum weighting coefficient so that we can reconstruct the surface shape of a scatterer at various distances of the observation points.

Satellite communications (SATCOM) systems play important roles in wireless communication systems. In the future, they will be required to accommodate rapidly increasing communication requests from various types of users. Therefore, we propose a framework for efficient resource management in large-scale SATCOM systems that integrate multiple satellites. Such systems contain hundreds of thousands of communication satellites, user terminals, and gateway stations; thus, our proposed framework enables simpler and more reliable communication between users and satellites. To manage and control this system efficiently, we formulate an optimization problem that designs the network structure and allocates communication resources for a large-scale SATCOM system. In this mixed integer programming problem, we allow the cost function to be a combination of various factors so that SATCOM operators can design the network according to their individual management strategies. These factors include the total allocated bandwidth to users, the number of satellites and gateway stations to be used, and the number of total satellite handovers. Our numerical simulations show that the proposed management strategy outperforms a conventional strategy in which a user can connect to only one specific satellite determined in advance. Furthermore, we determine the effect of the number of satellites in the system on overall system performance.

S-shaped nonlinearity is found in the electrical resistance-length relationship in an electroactive supercoiled polymer artificial muscle. The modulation of the electrical resistance is mainly caused by the change in the contact condition of coils in the artificial muscle upon deformation. A mathematical model based on logistic function fairly reproduces the experimental data of electrical resistance-length relationship.

In this paper, we introduce conditional decisions for enforcing forcible events in the decentralized supervisory control framework for timed discrete event systems. We first present sufficient conditions for the existence of a decentralized supervisor with conditional decisions. These sufficient conditions are weaker than the necessary and sufficient conditions for the existence of a decentralized supervisor without conditional decisions. We next show that the presented sufficient conditions are also necessary under the assumption that if the occurrence of the event tick, which represents the passage of one time unit, is illegal, then a legal forcible event that should be forced to occur uniquely exists. In addition, we develop a method for verifying the presented conditions under the same assumption.