Texture has been investigated as a cue for reconstructing 3-D structure. There are various textures in a natural scene. In this paper, the regularity of alignment of texture elements was manipulated to investigate its effect on human perception. The results show that the regularity affects human perception when only the texel density gradient is given as cue or the density cue is inconsistent with the compression cue. We introduce a model based on a MAP estimation to account for the result from a viewpoint of an integration of 3-D cues. The model simultaneously estimates texture properties and 3-D surface orientation by using prior knowledge about texture and 3-D surface. The performance of the model accounts for the experimental result well.

This paper describes design techniques for suppressing crosstalk in an optical transceiver module using PLC-hybrid-integration technologies and for achieving burst-mode operation with high sensitivity and wide dynamic range using CMOS-IC technologies. An arrangement that reduces the electrical crosstalk to less than -100 dB was designed using three-dimensional electromagnetic field analysis. The configurations of a newly developed instantaneous-response CMOS LD driver circuit is also described and instantaneous-response CMOS receiver circuit techniques are reviewed. With these techniques, we have succeeded in building optical transceiver modules for ATM-PON systems using PLC-hybrid-integration and inexpensive standard CMOS-IC fabrication processes. Under full-duplex operation at 156 Mb/s, fabricated transceiver modules showed receiver sensitivity of better than -34 dBm and dynamic range of over 28 dB, which satisfy both the class-B and class-C specifications recommended by ITU-T (International Telecommunication Union-Telecommunication standardization sector) G983.1 for the optical transceiver module for an ONU (optical network unit).

A clock recovery circuit is a key component in optical communication systems. In this paper, an optoelectronic clock recovery circuit is reported that monolithically integrates a resonant tunneling diode (RTD) and a uni-traveling-carrier photodiode (UTC-PD). The circuit is an injection-locked-type RTD oscillator that uses the photo-current generated by the UTC-PD. Fundamental and sub-harmonic clock extraction is confirmed for the first time with good clock recovery circuit characteristics. The IC extracts an electrical 11.55-GHz clock signal from 11.55-Gbit/s RZ optical data streams with the wide locking range of 450 MHz and low power dissipation of 1.3 mW. Furthermore, the extraction of a sub-harmonic clock from 23.1-Gbit/s and 46.2-Gbit/s input data streams is also confirmed in the wider locking range of 600 MHz. The RMS jitter as determined from a single sideband phase noise measurement is extremely low at less than 200 fs in both cases of clock and sub-harmonic clock extraction. To our knowledge, the product of the output power and operating frequency of the circuit is the highest ever reported for injection-locked-type RTD oscillators. These characteristics indicate the feasibility of the optoelectronic clock recovery circuit for use in future ultra-high-speed fully monolithic receivers.

It is an important problem in signal processing, system realization and system identification to find linear discrete-time systems which are consistent with given covariance parameters. This problem is formulated as a problem of finding discrete-time positive real functions which interpolate given covariance parameters. Various investigations have yielded several significant solutions to the problem, while there remains an important open problem concerning the McMillan degree. In this paper, we use more general input-output characteristics than covariance parameters and consider finding discrete-time positive real matrix functions which interpolate such characteristics. The input-output characteristics are given by the coefficients of the Taylor series at some complex points in the open unit disk. Thus our problem is a generalization of the interpolation problem of covariance parameters. We reduce the problem to a directional interpolation problem with a constraint and develop the solution by a state-space based new approach. The main results consist of the necessary and sufficient condition for the existence of the discrete-time positive real matrix function which interpolates the given characteristics and has a limited McMillan degree, and a parameterization of all such functions. These are a contribution to the open problem and a generalization of the previous result.

A novel 1470-nm-band (S+ band) wavelength-division multiplexing (WDM) transmission system is described. The first advantage of S+-band transmission is suppression of degradation caused by four-wave mixing (FWM), which has been the dominant impairment factor in WDM transmission systems on dispersion-shifted fibers (DSFs). FWM suppression by using the S+ band instead of the conventional 1550-nm-band (M band) is successfully demonstrated. The second advantage is expansion of the usable bandwidth by using the S+ band together with other wavelength bands. A triple-wavelength-band WDM repeaterless transmission experiment using the S+ band, the M band and the L band (1580-nm-band) is conducted over DSF, and it is shown that degradation due to inter-wavelength-band nonlinear interactions is negligible in the transmission. Moreover, the transmission performance of an S+-band linear repeating system is estimated by computer simulation, and compared with that of other wavelength-band systems. In the experiments, thulium-doped fiber amplifiers (TDFAs) are used for amplification of signals in the S+ band.

Over roughly the past decade, the lightwave-research community has converged upon a broad architectural vision of the emerging national-scale core network. The vision has been that of a transparent, reconfigurable, wavelength-routed network, in which signals propagate from source to destination through a sequence of intervening nodes without optoelectronic conversion. Broad benefits have been envisioned. Despite the spare elegance of this vision, it is steadily becoming clear that due to the performance, cost, management, and multivendor-interoperability obstacles attending transparency, the needs of civilian communications will not drive the core network to transparency on anything like a national scale. Instead, they will drive it to 'opaque' form, with critical reliance on optoelectronic conversion via transponders. Transponder-based network architectures in fact not only offer broad transmission and manageability benefits. They also make networking at the optical layer possible by offering to the nodes managed and performance-engineered standard-interface signals that can then be reconfigured for provisioning and restoration purposes by optical-layer elements. Because of this, the more pressing challenges in lightwave networking are steadily shifting towards the mechanisms that will be used for provisioning and restoration. Among these are mechanisms based on free-space micromachined optical crossconnects. We describe recent progress on these new devices and the architectures into which they fit, and summarize the reasons why they appear to be particularly well-matched to the task of provisioning and restoring opaque multiwavelength core long-haul networks.

Aiming at wideband and flat supercontinuum generation (SC) from optical fibers in the 1.55-µm wavelength region, we study both experimentally and theoretically how SC spectra are influenced by group-velocity dispersion (GVD) of fibers. In the anomalous GVD region, since the peak power of pump pulses is kept high during propagation through the fiber by the higher-order soliton effect, the Raman effect has an adverse effect to flat and wideband SC generation. In the zero GVD region, the interplay of the third-order dispersion (TOD) and the self-phase modulation splits the SC spectrum into two main components. On the other hand, in the normal GVD region, nevertheless the SC spectrum broadens wider and smoother than those in anomalous and zero GVD regions, it is still asymmetric when TOD of the fiber can not be ignored. From these results, we find that a dispersion-flattened fiber with normal GVD is the most suitable for flat and wideband SC generation. A 280-nm wide SC spectrum with the spectral-density fluctuation less than 10 dB is actually generated from such a fiber.

This paper discusses global area optical transport ring networks using wavelength division multiplexing (WDM) technologies and proposes a novel optical add/drop multiplexer (OADM) architecture suitable for such an application field. Study on the requirements of a global area ring application elucidates the appropriate ring/protection architecture as the path switched bi-directional ring. The proposed OADM architecture has flexibility in terms of path provisioning and scalability. We conclude that the proposed OADM can effectively configure the large-scale path switched bi-directional rings.

The statistical behavior of the amplitude probability distribution of intermodulation distortion interference in multichannel optical-cable TV systems was experimentally investigated. In multichannel transmission, the non-linearity of a laser diode (LD) or an electrical amplifier can cause intermodulation distortion (composite-second-order beat; CSO, composite-triple-beat; CTB, etc. ). Even though it has been discussed as laser-clipping distortion, intermodulation distortion is usually distortion from AM-VSB carriers. The statistical analysis and evaluation of the distortion in transmitted channel is in controversial. We evaluated the distortion in 20 frequency-division-multiplexed 16-QAM channels, with each carrier carrying 80 Mbps for an optical cable TV system. We first enumerated the distortion components causing interference in each transmission channel so as to identify the intermodulation products. Then, in selected channels, we precisely measured the power of each kind of distortion and the amplitude distributions of the intermodulation distortion from sinusoidal and digital-modulated carriers on cable TV as a function of optical modulation depth (OMD) of LD. And we clarified how the probability distribution function (PDF) changed as the OMD increased. Also, the BER performance of a 16-QAM signal was measured and compare to the intermodulation behavior of the different distortion sources. We found evidence that the amplitude distribution of intermodulation distortion from digital carriers differs from that of thermal noise. Experimental results showed that the PDF of the intermodulation distortion changed when the ratio of intermodulation distortion among all undesired signals varied with the OMD. The BER performance varied with intermodulation of both analogue and digital carriers even when the carrier to interference noise power ratio (CIR) is the same.

We have developed a low-latency, error-correcting-code-(ECC-)adaptable skew-compensation technique, which is needed for high-speed and long-distance parallel optical interconnections. A new frame-coding technique called shuffled mB1C encoding, which requires no clock-rate conversion circuit and no data buffering, and a new skew-measurement method which is suitable for ECC adaptation have been developed for the compensation. Full-digital skew-compensation circuits using these new techniques were able to compensate for a two-clock-cycle skew, even when one transmission channel was removed. The maximum latency for skew compensation was only five clock cycles.

In the present paper, a new coding scheme for infrared ASK communication systems--Pulse Sequence Modulation (PSM)--will be proposed, which uses a combination of pulse sequences so that it canattain zero-spectrum points at specific frequencies within the main-lobe region. The interference to the other IR systems was a problem of the conventional infrared ASK communication systems. The proposed PSM coding scheme reduces the interference by decreasing the emission at specific frequencies, and helps multiple IR communication systems co-exist without deteriorating coding efficiency.

We developed an optical transceiver diode (TRAD) module for bi-directional time-compression-multiplexing (TCM) transmission systems. A wavelength-insensitive structure as a receiver and a low-capacitance configuration in the module provide a high sensitivity. Stable switching of 156 Mbit/s NRZ burst signals between the transmitter and receiver modes is achieved. In addition, it is shown that optical module cost can be further reduced by using passive alignment on a Si bench.

A 1.55-µm hybrid integrated wavelength-converter module was fabricated using a two-channel spot-size converter integrated semiconductor optical amplifier (SS-SOA) on a planar-lightwave-circuit (PLC) platform. Clear eye opening and penalty-free wavelength conversion were obtained at 2.5-Gb/s modulation with a wide wavelength difference of 46 nm. The module showed good characteristics including low insertion loss (0.1 dB), and high conversion efficiency (-0.2 dB). It also showed stable wavelength conversion for as wide as a 13 temperature range.

In many applications of digital video database systems such as digital library, video data is often compressed with MPEG video algorithms. It will be an important technique to insert the additional information data like indexes and contents effectively into video database which is compressed with MPEG, because we can always deal with the additional information with video data itself easily. We propose a method for inserting optional binary data such as index information of digital library into MPEG-1 and -2 bitstreams. The binary data inserted MPEG video bitstreams using our proposed scheme are also according to the specification of the MPEG video frame structure. The proposed method allows us to extract the inserted binary data perfectly though MPEG-1 and -2 video are lossy algorithms. And the quality of decoded images after extracting added information is almost the same as that of ordinary MPEG bitstreams. Furthermore, traditional standard MPEG-1 and -2 video decoder which can not extract inserted binary data can also decode images from the binary data inserted MPEG video bitstreams without obvious image degradation. There are some different points between the proposed insertion technique of the binary data and the watermarking technique. The technique of watermarking prepares to deal with alter watermarking by others. And the technique of watermarking is required for the identification of the signature and the perfect extraction of the inserted image signature is not required in the lossy MPEG video environment. On the other hand, we have to extract all of the inserted binary information data correctly with the insertion technique of the binary information. Simulations using MPEG video sequences with inserted binary data are presented to quantify some performance factors concerned. We have not heard about inserting data method which purpose is such as index and content information insertion.

The problem of transient scattering caused by abrupt extinction of a terminative conducting screen in a waveguide is considered. First, a boundary-value problem is formulated to describe the transient phenomena, the problem in which the boundary condition depends on time. Then, application of the Fourier transformation with respect to time derives a Wiener-Hopf-type equation, which is solved by a commonly known decomposition procedure. The transient fields are obtained through the deformation of the integration path for the inverse transformation and the results are represented in terms of the incomplete Lipschitz-Hankel integrals. Numerical examples showing typical transient phenomena are attached.

A wavelength division multiplexing (WDM) optical path-based Internet protocol (IP) backbone network is proposed as a cost-effective way of realizing robust IP-over-photonic systems. The WDM optical path is based on WDM transmission and wavelength routing. Between end-to-end IP backbone routers, the WDM optical path, a fat and robust optical pipe, is defined across photonic transport systems (PTS's). Tera-bit class PTS's will be required for the future IP backbone network and this level of performance is achievable. Optical layer routing is done at intermediate nodes, so the electrical packet-by-packet routing required by existing systems is eliminated. An optical signal format that permits cost-effective IP packet transmission is presented. WDM optical paths directly accommodate the IP packets via layer-2 frames. The cost-effectiveness of the proposed system, especially for heavy traffic, is demonstrated from the viewpoint of the overall network traffic transport capability and network node cost. The proposed system is as robust as existing systems; e. g. fault/degradation localization mechanism and optical layer network protection one are implemented. Thus the proposed IP-over-photonic system will create cost-effective and robust IP backbone networks.

This paper describes design techniques for suppressing crosstalk in an optical transceiver module using PLC-hybrid-integration technologies and for achieving burst-mode operation with high sensitivity and wide dynamic range using CMOS-IC technologies. An arrangement that reduces the electrical crosstalk to less than -100 dB was designed using three-dimensional electromagnetic field analysis. The configurations of a newly developed instantaneous-response CMOS LD driver circuit is also described and instantaneous-response CMOS receiver circuit techniques are reviewed. With these techniques, we have succeeded in building optical transceiver modules for ATM-PON systems using PLC-hybrid-integration and inexpensive standard CMOS-IC fabrication processes. Under full-duplex operation at 156 Mb/s, fabricated transceiver modules showed receiver sensitivity of better than -34 dBm and dynamic range of over 28 dB, which satisfy both the class-B and class-C specifications recommended by ITU-T (International Telecommunication Union-Telecommunication standardization sector) G983.1 for the optical transceiver module for an ONU (optical network unit).

Aiming at wideband and flat supercontinuum generation (SC) from optical fibers in the 1.55-µm wavelength region, we study both experimentally and theoretically how SC spectra are influenced by group-velocity dispersion (GVD) of fibers. In the anomalous GVD region, since the peak power of pump pulses is kept high during propagation through the fiber by the higher-order soliton effect, the Raman effect has an adverse effect to flat and wideband SC generation. In the zero GVD region, the interplay of the third-order dispersion (TOD) and the self-phase modulation splits the SC spectrum into two main components. On the other hand, in the normal GVD region, nevertheless the SC spectrum broadens wider and smoother than those in anomalous and zero GVD regions, it is still asymmetric when TOD of the fiber can not be ignored. From these results, we find that a dispersion-flattened fiber with normal GVD is the most suitable for flat and wideband SC generation. A 280-nm wide SC spectrum with the spectral-density fluctuation less than 10 dB is actually generated from such a fiber.

We propose manifold piecewise constant systems (ab. MPC) and consider basic phenomena: the 2-D, 3-D and 4-D MPCs exhibit limit-cycle, line-expanding chaos and area-expanding chaos, respectively. The righthand side of the state equation is piecewise-constant, hence the system dynamics can be simplified into a piecewise-linear return map which can be expressed explicitly. In order to analyze the piecewise-linear return map, we introduce an evaluation function for the piecewise-linear return map and give theoretical evidence for chaos generation. Also the chaotic behaviors are demonstrated in the laboratory.

In 2001, the DEMETER micro-satellite will be launched to perform Detection of Electro-Magnetic Emissions Transmitted from Earthquake Regions. Its main scientific objective is related to the investigation of the ionospheric perturbations due to the seismic and volcanic activity. A system allowing an onboard identification and characterization of spatially and temporally coherent structures associated with the measurement of one or several electromagnetic wave field components is used. It is based on neural networks. The choice and training of the neural network are done on the ground from available waveforms. The parameters of the neural network system are then transmitted to the satellite. This reconfiguration process can be repeated whenever necessary during the space mission. Details about the functioning and coding optimization for DSP implementation is presented. The first function of this system which will be performed on the satellite DEMETER is the real-time identification and characterization of whistler phenomena. An application to the analysis of such phenomena observed in data from the AUREOL-3 satellite is exposed.