In this letter, we investigate the performance of cooperative decode-and-forward multiple-input multiple-output relaying system using orthogonal space-time block codes with piecewise-linear (PL) receiver over correlated Nakagami-m fading channels for integer values of m. We derive the closed-form expression for the exact bit error rates of binary phase shift keying signals. The analytical expression is validated through numerical results. It is shown that the performance of PL receiver outperforms that of conventional maximal ratio combining receiver.

A deeply-coupled system can feed the INS information into a GNSS receiver, and the signal tracking precision can be improved under dynamic conditions by reducing tracking loop bandwidth without losing tracking reliability. In contrast to the vector-based deep integration, the scalar-based GNSS/INS deep integration is a relatively simple and practical architecture, in which all individual DLL and PLL are still exist. Since the implementation of a deeply-couple system needs to modify the firmware of a commercial hardware GNSS receiver, very few studies are reported on deep integration based on hardware platform, especially from academic institutions. This implementation-complexity issue has impeded the development of the deeply-coupled GNSS receivers. This paper introduces a scalar-based MEMS IMU/GNSS deeply-coupled system based on an integrated embedded hardware platform for real-time implementation. The design of the deeply-coupled technologies is described including the system architecture, the model of the inertial-aided tracking loop, and the relevant tracking errors analysis. The implementation issues, which include platform structure, real-time optimization, and generation of aiding information, are discussed as well. The performance of the inertial aided tracking loop and the final navigation solution of the developed deeply-coupled system are tested through the dynamic road test scenarios created by a hardware GNSS/INS simulator with GPS L1 C/A signals and low-level MEMS IMU analog signals outputs. The dynamic tests show that the inertial-aided PLL enables a much narrow tracking loop bandwidth (e.g. 3Hz) under dynamic scenarios; while the non-aided loop would lose lock with such narrow loop bandwidth once maneuvering commences. The dynamic zero-baseline tests show that the Doppler observation errors can be reduced by more than 50% with inertial aided tracking loop. The corresponding navigation results also show that the deep integration improved the velocity precision significantly.

We consider uplink multi-carrier code-division multiple access (MC-CDMA) systems in a multi-cell environment. It is assumed that all intra-cell users employ Alamouti's simple space-time block coding (STBC), which is known to the base station receiver, but the receiver has no information on whether inter-cell users employ STBC or not. In this case we propose a blind adaptive minimum output energy (MOE) receiver for uplink STBC MC-CDMA, which is designed to perfectly remove the interference from intra-cell users by using the spreading sequence information on all intra-cell users and to reduce the interference from inter-cell users by minimizing the constrained output energy. Analysis and simulation results show that the proposed adaptive receiver has a faster convergence rate and higher steady-state signal-to-interference plus noise ratio (SINR) than a conventional scheme in which only the spreading code information of the desired user is utilized.

This paper proposes a reduced-complexity multiband multiple-input multiple-output (MIMO) receiver that can be used in cognitive radios. The proposed receiver uses heterodyne reception implemented with a wide-passband band-pass filter in the radio frequency (RF) stage. When an RF Hilbert transformer is utilized in the receiver, image-band interference occurs because of the transformer's imperfections. Thus, the imperfection of the Hilbert transformer is corrected in the intermediate frequency (IF) stage to reduce the hardware complexity. First, the proposed receiver estimates the channel impulse response in the presence of the strong image-band interference signals. Next, the coefficients are calculated for the correction of the imperfection at the IF stage, and are fed back to the IF stage through a feedback loop. However, the imperfection caused by the digital-to-analog (D/A) converter and the baseband amplifier in the feedback loop corrupts the coefficients on the way back to the IF stage. Therefore, the proposed receiver corrects the imperfection of the analog devices in the feedback loop. The performance of the proposed receiver is verified by using computer simulations. The proposed receiver can maintain its performance even in the presence of strong image-band interference signals and imperfection of the analog devices in the feedback loop. In addition, this paper also reveals the condition for rapid convergence.

In this paper, a symbol-rate clock recovery scheme for a receiver that uses an integrating decision feedback equalizer (DFE) is proposed. The proposed clock recovery using expected received signal amplitudes as the criterion realizes minimum mean square error (MMSE) clock recovery. A receiver architecture using an integrating DFE with the proposed symbol-rate clock recovery is also proposed. The proposed clock recovery algorithm successfully recovered the clock phase in a system level simulation only with a DFE. Higher jitter tolerance than 0.26 UIPP at 10 Gb/s operation was also confirmed in the simulation with an 11 dB channel loss at 5 GHz.

In this paper, we propose a high-speed full-duplex optical wireless communication system using a single channel imaging receiver for personal area network applications. This receiver is composed of an imaging lens, a small sensitive-area photodiode, and a 2-aixs actuator and it can reject most of the background light. Compared with the previously proposed system with single wide field-of-view (FOV) non-imaging receiver, the coverage area at 12.5 Gb/s is extended by > 20%. Furthermore, since the rough location information of the user is available in our proposed system, instead of searching for the focused light spot over a large area on the focal plane of the lens, only a small possible area needs to be scanned. In addition, by pre-setting a proper comparison threshold when searching for the focused light spot, the time needed for searching can be further reduced. Proof-of-concept experiments have been carried out and the results show that with this partial searching algorithm and pre-set threshold, better performance is achieved.

The design and measured results of a 120 GHz/140 GHz dual-channel OOK (ON-OFF Keying) receiver are presented in this paper. Because a signal with very wide frequency width is difficult to process in a single-channel receiver, a dual-channel configuration with channel selection is adopted in the proposed receiver. The proposed receiver is fabricated using 65 nm CMOS technology. The measured data rate of 3.0 and 3.6 Gbps, minimum sensitivity of -25.6 and -27.1 dBm, communication distance of 0.30 and 0.38 m are achieved in the 120- and 140-GHz receiver, respectively. The correct channel selection is achieved in the 120-GHz receiver. These results indicate the possibility of the CMOS multiband receiver operating at over 100 GHz for low-power high-speed proximity wireless communication systems.

A LNA, an RF front-end and a 6th–order complex BPF for reconfigurable low-IF receivers are demonstrated in this work. Due to the noise cancellation, the two-stage LNA presents a low NF of 2.8 to 3.3 dB from 0.8 to 6 GHz. Moreover, the LNA delivers two kinds of gain curves with IIP3 of -2.6 dBm by employing the capacitive degeneration and the resistive gain-curve shaping in the second stage. The flicker noise corner frequency of the down-converter has been considered and the measured fC of the RF front-end is 200 kHz. The RF front-end also provides two kinds of gain curves. For the low-frequency mode, the conversion gain is 28.831.1 dB from 800 MHz to 2.4 GHz. For the high-frequency mode, the conversion gain is 26.827.4 dB from 3 to 5 GHz. The complex BPF is realized with gm-C LPFs by shifting the low-pass frequency response. With variable transconductances and capacitors, a fixed ratio of the centre frequency to the bandwidth (2) is achieved by varying the bandwidth and the centre frequency of the LPF simultaneously. The complex BPF has a variable bandwidth from 200 kHz to 6.4 MHz while achieving an image rejection of 44 dB.

To reduce the power dissipation of the receiver in accordance with the intensity of the received signal, we developed the first intra-symbol intermittent (ISI) radio-frequency (RF) front end with 0.35-µm CMOS technology. In the demodulation mechanism, the RF output of the low-noise amplifier (LNA) is down-converted to an intermediate frequency (IF) by the mixer, and the LNA and mixer operate synchronously and intermittently within the length of a single symbol. Because the time-averaged power consumption is proportional to the operating time, the demodulation can be performed with low power by making the total operating time short. We experimentally demonstrate that demodulation (BPSK: 9.6 kbps) is properly achieved with the operating-time ratio of 12%. This ISI operation of the RF front end is enabled by a newly devised fast-transition LNA and mixer. A theoretical analysis of aliasing noise reveals that RF ISI operation is more useful than current-control with continuous operation and that an operating-time ratio of 10% is optimal.

This paper proposes a novel scheme called as“frequency domain imbalance estimation” that estimates the imbalance of the Hilbert transformer in heterodyne multimode/band receivers with baseband automatic gain control (AGC). The proposed scheme uses correlation matrices in the frequency domain. This enables the receivers to keep high transmission performance in spite of the imbalance of the analog Hilbert transformer, by offsetting the imbalance. Moreover, the baseband AGC relaxes the requirement of the baseband A/D converter. The performance of imbalance estimation and imbalance cancellation is verified by computer simulation. As a result, it is shown that the proposed scheme not only estimates the imbalance of Hilbert transformer with extremely high precision, but also cancels the image-band interference such that it achieves the theoretical performance.

This paper presents a multi-band WCDMA receiver consisting of a multi-band low noise amplifier (LNA), a multi-band mixer and an inter-stage tunable notch filter. The notch filter is used to suppress Tx leakage, and 0.8–1.5 GHz (66%) of tuning range is achieved. The receiver achieves 33 and 30 dB conversion gain, 6.4 and 8 dB NF, 50 and 35.5 dBm IIP2, and -6 and -4.7 dBm IIP3 at 0.8 and 1.5 GHz, respectively. The power consumption is 121 mW from a 1.8-V power supply. The receiver is implemented in a 0.18-µm CMOS process.

With the development of Global Navigation Satellite System (GNSS), the amount of related research is growing rapidly in China. A lot of accomplishments have been achieved in all branches of the satellite navigation field, especially motivated by the BeiDou Program. In this paper, the current status, technologies and developments in satellite positioning and navigation in China are introduced. Firstly, an overview and update of the BeiDou Program is presented, known as the three-step development strategy for different services. Then signal design for the BeiDou system is discussed, including the generation of pseudo-random noise (PRN) codes for currently available signal B1, and the investigation of a new signal modulation scheme for interoperability at open frequency B1C. The B1C signal should comply to Multiplexed Binary Offset Carrier (MBOC) constrains, and a modulation called Quadrature Multiplexed BOC (QMBOC) is presented, which is equivalent to time-multiplexed BOC (TMBOC) for GPS and composite BOC (CBOC) for Galileo, while overcomes the drawback of CBOC. Besides, the inter and intra system compatibility is discussed, based on the effective C/N0 proposed by International Telecommunication Union (ITU). After that, receiver technologies in challenging environments are introduced, such as weak signal acquisition and assisted GNSS (A-GNSS). Moreover, a method of ambiguity mitigation for adaptive digital beam forming (ADBF) in large spacing antenna arrays is proposed, by which interference suppression is available. Furthermore, cutting edge technologies are brought in, including seamless navigation for indoor and outdoor, and collaborative navigation. After all, GNSS applications in China for industry and daily life are shown, as well as the market prospection.

The Multiple-Input Multiple-Output (MIMO) Zero-Forcing (ZF) receiver requires accurate Channel State Information (CSI), which is impacted by channel estimation error, to perform properly. Moreover, interference occurs due to the change of channel coefficients between the channel estimation events in fading channels. Thus, in practice, both channel estimation error and interference greatly influence Bit Error Rate (BER) performance. In this letter, we derive an Signal-to-Interference-and-Noise Ratio (SINR) expression considering both channel estimation error and interference and develop approximate closed-form BER expressions of M-PSK and M-QAM for the MIMO ZF receiver in Nakagami-m fading channels. We then analyze the effects of channel estimation error, interference, and the numbers of transmit and receive antennas.

Single front-end architecture with parasitic antenna element (PAE) in compact array system has been proposed for enhancing spectral efficiency and miniaturizing the receiver. Although most of studies paid attention to design optimal receiver with antenna mutual coupling on fading correlation, relatively little attention has been paid to noise. In this paper, we propose a low noise model for single front-end MIMO receiver system with PAE which includes arbitrary signal and noise coupling. The proposed model articulates physical noise sources and relates their spatial correlation with array receive antennas, parasitic element, front-end and matching circuit. A matching circuit is designed to achieve minimum noise figure. After that, the optimal PAE value is derived to maximize channel capacity. We present numerical analysis to verify the proposed system on certain conditions.

This paper presents a novel 2-D (2-dimension) receiver that adopts the reception scheme to promote OFDM-DS-CDMA (orthogonal frequency division multiplexing multi-carrier coded-division multiple-access) system performance. The system model includes spread coding and a system block diagram of the 2-D receiver shown graphically with 3-D (three dimensions) plots. The analytical calculation of system performance for an OFDM-DS-CDMA system combined with the proposed receiver equipment is investigated. To evaluate the results from the channel fading effect is considered over the correlated fading environments. The correlated-Nakagami-m statistical distribution is taken into account in the evaluation. The results show that the number of users, the number of subcarriers and the fading channel correlation generally affect OFDM-DS-CDMA systems. The system is also influenced by the Doppler shift and the signal propagation environment (fading parameter).

This paper presents an efficient implementation of OFDM inner receiver on a programmable multi-core processor platform with CMMB as an application. The platform consists of an array of programmable SIMD processors interconnected in a 2-D mesh network, which can provide high performance and is quite suitable for wireless communication applications. Implemented on one cluster with 8 cores, the receiver includes symbol timing, carrier frequency offset and sampling frequency offset synchronization, channel estimation and equalization. Multiple optimization techniques are explored to improve system throughput such as: task-level parallelism on many cores, data-level parallelism on SIMD cores, minimization of memory access and route-length-minimization task mapping techniques. Besides, efficient memory strategy and specific instructions for complex computation increase the performance. The simulation results show that the inner receiver could achieve a throughput of up to 120 Mbps when operating at 750 MHz.

To realize economical optical burst signal receivers for the Optical Network Unit (ONU) of the Ethernet Optical Switched Access Network (E-OSAN), we previously implemented optical burst receivers with AC-coupling and DC-coupling using off-the-shelf components, and showed that the former offers better performance. This paper proposes a new optical burst signal receiver that uses the transfer function, Gn(s) = 1-Hn(s), where Hn(s) denotes a Bessel filter transfer function of order n. We also present a method for designing the proposed receiver and clarify that it has better performance than the conventional AC-coupling one. We then present an LCR circuit synthesis of Gn(s), which is necessary to actually implement a burst receiver based on the proposal.

We present a highly integrated quasi-millimeter-wave receiver MMIC that integrates 22 circuits in a 3 2.3 mm area using three-dimensional MMIC (3D-MMIC) technology. The MMIC achieves low noise (3 dB) and high gain (41 dB) at 26 GHz by using an on-chip image reject filter. It integrates a multiply-by-eight (X8) local oscillator (LO) chain with the IF frequency of the 2.4 GHz band and can use low-cost voltage-controlled oscillators (VCOs) and demodulators in a 2–3 GHz frequency band. Multilayer inductors contribute to the miniaturization especially in a 2–12 GHz frequency band. Furthermore, it achieves a high dynamic range by using two step attenuators with a new built-in inverter using an N-channel depression field-effect transistor (FET). The power consumption of the MMIC is only 450 mW.

This paper proposes an active-RC filter that achieves a wide pseudo-continuous bandwidth-tuning range and a wide gain range with fine steps using a novel switched resistor architecture. A channel-selection filter with the proposed resistor bank is designed for a multi-mode mobile-TV receiver with the 6th order Chebyshev-I topology. The bandwidth, 0.5–6 MHz with 5% steps, supports multiple mobile-TV standards with sufficient margins for process and temperature variations. The filter also accomplishes a 30-dB variable gain range with 6-dB steps, and it relaxes the dynamic range requirement of a succeeding programmable gain amplifier. The power consumption of the filter, 3.4–5.0 mW, is adjustable according to the bandwidth and the signal level. The filter was fabricated with on-chip bandwidth-calibration circuitry in 0.18-µm CMOS and occupied 0.81 mm2.

Over 100 Gbit/s/ch high-speed optical transmission is required to achieve the high capacity networks that can meet future demands. The coherent receiver, which is expected to yield high frequency utilization, is a promising means of achieving such high-speed transmission. However, it requires a high-speed Analog to Digital Converter (ADC) because the received signal bandwidth would be over several tens or hundreds of GHz. To solve this problem, we propose a band-divided receiver structure for wideband optical signals. In the receiver, received wideband signals are divided into a number of narrow band signals without any guard band. We develop a band-divided receiver prototype and evaluate it in an experiment. In addition, we develop a real-time OFDM demodulator on an FPGA board that implements 1.5 GS/s ADCs. We demonstrate that the band-divided receiver prototype with its real-time OFDM demodulator and 1.5 GS/s ADC can demodulate single polarization 12 Gbit/s OFDM signals in real-time.