In this paper, the analog code modulation characteristics of distributed-based transversal filters (DTFs) suitable for use in spectrally encoded CDMA systems are presented. The DTF is verified as an appropriate method to use in high-speed CDMA systems as opposed to previously proposed methods, which are intended for Direct Sequence (DS) CDMA systems. The large degree of freedom of DTF design permits controlling the filter pulse response to generate well specified temporal phase-coded signals. A decoder structure that performs bipolar detection of user subbands giving rise to a Spectral-Amplitude Encoded CDMA system is considered. Practical implementations require truncating the spreading signals by a time window of duration equal to the span time of the tapped delay line. Filter functions are chosen to demodulate the matched channel and achieve improved user interference rejection avoiding the need for transversal filters featuring a large number of taps. As a proof-of-concept of the electronic SAE scheme, practical circuit designs are developed at low speeds (3-dB point at 1 GHz) demonstrating the viability of the proposal.

A summer-embedded sense amplifier (SE SA) is proposed to reduce feedback loop delay (TFB) in a decision feedback equalizer (DFE). In the SE SA, the position of the ISI compensator is changed from the latch input to the latch output, and hence the TFB is reduced. The simulated DFE achieves 32Gb/s and 66fJ/b with a 1-V 65-nm CMOS process.

Nyquist folding receiver (NYFR) is a novel reconnaissance receiving architecture and it can realize wideband receiving with small amount of equipment. As a tradeoff of non-cooperative wideband receiving, the NYFR output will add an unknown key parameter that is called Nyquist zone (NZ) index. In this letter, we concentrate on the NZ index estimation of the NYFR output. Focusing on the basic pulse radar signals, the constant frequency signal, the binary phase coded signal and the linear frequency modulation signal are considered. The matching component function is proposed to estimate the NZ indexes of the NYFR outputs without the prior information of the signal modulation type. In addition, the relations between the matching component function and the parameters of the NYFR are discussed. Simulation results demonstrate the efficacy of the proposed method.

A simple and novel multiple-symbol differential detection (MSDD) scheme is proposed for IEEE 802.15.4 binary phase shift keying (BPSK) receivers. The detection is initiated by estimating and compensating the carrier frequency offset (CFO) effect in the chip sample of interest. With these new statistics, the decisions are jointly made by allowing the observation window length to be longer than two bit intervals. Simulation results demonstrate that detection reliability of the IEEE 802.15.4 BPSK receivers is significantly improved. Namely, at packet error rate (PER) of 1×10-3, the signal-to-noise ratio (SNR) gap between ideal coherent detection (perfect carrier reference phase and no CFO) with differential decoding and conventional optimal single differential coherent detection (SDCD) is filled by 2.1dB when the observation window length is set to 6bit intervals. Then, the benefit that less energy consumed by retransmissions is successfully achieved.

Optimal loads and maximum achievable efficiency for multiple-receiver inductive power transfer (IPT) system have been formulated by theoretical studies in literatures. This paper presents extended analysis on system behavior at optimal load condition and extensive S-parameter evaluation to validate the formulas. Our results confirm that at the optimal load condition, the system is in a resonance state; the impact of cross-coupling among receivers is completely mitigated; and the efficiency reaches its maximum expressed by an efficiency angle tangent, in an manner analogous to the well-known kQ-theory for single-receiver IPT. Our contributions do not lie in practical applications of multiple-receiver IPT but in establishing principles for design and benchmarking the system.

The introduction of a drone-based mobile sink into wireless sensor networks (WSNs), which has flexible mobility to move to each sensor node and gather data with a single-hop transmission, makes cumbersome multi-hop transmissions unnecessary, thereby facilitating data gathering from widely-spread sensor nodes. However, each sensor node spends significant amount of energy during their idle state where they wait for the mobile sink to come close to their vicinity for data gathering. In order to solve this problem, in this paper, we apply a wake-up receiver to each sensor node, which consumes much smaller power than the main radio used for data transmissions. The main radio interface is woken up only when the wake-up receiver attached to each node detects a wake-up signal transmitted by the mobile sink. For this mobile and on-demand data gathering, this paper proposes a route control framework that decides the mobility route for a drone-based mobile sink, considering the interactions between wake-up control and physical layer (PHY) and medium access control (MAC) layer operations. We investigate the optimality and effectiveness of the route obtained by the proposed framework with computer simulations. Furthermore, we present experimental results obtained with our test-bed of a WSN employing a drone-based mobile sink and wake-up receivers. All these results give us the insight on the role of wake-up receiver in mobile and on-demand sensing data gathering and its interactions with protocol/system designs.

This paper presents low-noise amplifier (LNA)-less 300-GHz CMOS receivers that operate above the NMOS unity-power-gain frequency, fmax. The receivers consist of a down-conversion mixer with a doubler- or tripler-last multiplier chain that upconverts an LO1/n signal into 300 GHz. The conversion gain of the receiver with the doubler-last multiplier is -19.5 dB and its noise figure, 3-dB bandwidth, and power consumption are 27 dB, 27 GHz, and 0.65 W, respectively. The conversion gain of the receiver with the tripler-last multiplier is -18 dB and its noise figure, 3-dB bandwidth, and power consumption are 25.5 dB, 33 GHz, and 0.41 W, respectively. The receivers achieve a wireless data rate of 32 Gb/s with 16QAM. This shows the potential of the moderate-fmax CMOS technology for ultrahigh-speed THz wireless communications.

This paper describes a top-down design methodology to optimize resonant capacitance in a wireless power transfer system with 3-D stacked two receivers. A 1:2 selective wireless power transfer is realized by a frequency/time division multiplexing scheme. The power transfer function is analytically formulated and the optimum tuning capacitance is derived, which is validated by comparing with system simulation results. By using the optimized values, power transfer efficiencies at 6.78MHz and 13.56MHz are simulated to be 80% and 84%, respectively, which are <3% worse than a conventional wireless power transfer system.

To meet the demand for continuous increase in data traffic, full usage of polarization freedom of light is becoming inevitable in the next-generation optical communication and datacenter networks. In particular, Stokes-vector modulation direct-detection (SVM-DD) formats are expected as potentially cost-effective method to transmit multi-level signals without using costly coherent transceivers in the short-reach links. For the SVM-DD formats to be practical, both the transmitter and receiver need to be substantially simpler, smaller, and lower-cost as compared to coherent counterparts. To this end, we have recently proposed and demonstrated novel SV modulator and receiver circuits realized on monolithic InP platforms. With compact non-interferometric configurations, relatively simple fabrication procedures, and compatibility with other active photonic components, the proposed devices should be attractive candidate in realizing low-cost monolithic transceivers for SVM formats. In this paper, we review our approaches as well as recent progresses and provide future prospects.

We present an 82.5GS/s over-sampling based burst-mode clock and data recovery (BM-CDR) IC chip-set comprising an 82.5GS/s over-sampling IC using 8×10.3GHz multi-phase clocks and a dual-rate data selector logic IC to realize the 10.3Gb/s and 1.25Gb/s dual-rate burst-mode fast-lock operation required for 10-Gigabit based fiber-to-the-x (FTTx) services supported by 10-Gigabit Ethernet passive optical network (10G-EPON) systems. As the key issue for designing the proposed 82.5GS/s BM-CDR, a fresh study of the optimum number of multi-phase clocks, which is equivalent to the sampling resolution, is undertaken, and details of the 10.3Gb/s cum 1.25/Gb/s dual-rate optimum phase data selection logic based on a blind phase decision algorithm, which can realize a full single-platform dual-rate BM-CDR, ate also presented. By using the power of the proposed 82.5GS/s over-sampling BM-CDR in cooperation with our dual-rate burst-mode optical receiver, we further demonstrated that a short dual-rate and burst-mode preamble of 256ns supporting receiver settling and CDR recovery times was successfully achieved, while obtaining high receiver sensitivities of -31.6dBm at 10.3Gb/s and -34.6dBm at 1.25Gb/s and a high pulse-width distortion tolerance of +/-0.53UI, which are superior to the 10G-EPON standard.

This paper presents a 44 Gbit/s Transimpedance Amplifier (TIA) with wide-dynamic range and high-linearity for optical receiver fabricated in 130 nm BiCMOS technology. The TIA has the features of 67dBΩ overall transimpedance gain, a bandwidth of 28GHz, 10pA/√Hz of Input Referred Noise Current Power Spectral Density (IRNCPSD), and a power consumption of 95mW from a 2.5V supply. The Total Harmonic Distortion (THD) is less than 5% for a differential input current up to 2.63mApp, when the static input current is 0.1mA.

To support the rapid increase of mobile traffic, the LTE-based air interface is expected to be employed in the unlicensed spectrum known as “Licensed-Assisted Access (LAA).” The LAA terminal, which employs an LTE-based air interface, suffers from interference from WiFi access points as well as the LAA base station. The interference rejection combining (IRC) receiver, which employs a linear minimum mean square error (MMSE) filter, can suppress this interference from WiFi access points in addition to that of the LAA base station. The IRC receiver is effective, since it requires no knowledge of the interference, which is generally difficult to obtain for different systems. In this paper, we use a link-level simulation to evaluate the performance of the IRC receiver in suppressing the interference from WiFi access points, and show that the IRC receiver can effectively cancel the interference from WiFi systems as well as LTE systems, although we observed a slight performance degradation due to the covariance matrix estimation error caused by the WiFi interference fluctuation in the frequency-domain.

Among various indoor positioning technologies, impulse-radio UWB is a promising technique to provide indoor positioning and tracking services with high precision. Because UWB regulations turned to imposing restrictions on UWB low band, UWB high band becomes attractive for enabling simple and low cost implementation. However, UWB high band endures much larger propagation loss than UWB low band. In this paper, we propose two separated methods to compensate the deficiency of high band in propagation. With the first method, we bundle several IR-UWB modules to increase the average transmission power, while an adaptive detection threshold is introduced at the receiver to raise receiving sensitivity with the second method. We respectively implement each of these two proposed methods and evaluate their performance through measurements in laboratory. The results show that each of them achieves about 7dB gains in signal power. Furthermore, positioning performance of these two proposed methods are evaluated and compared through field measurements in an indoor sports land.

We numerically investigate a PDM-QPSK multi-rate coherent burst-mode optical receiver capable of receiving 3 different line-rates, suitable for next generation optical networks such as hybrid optical circuit switching (OCS)/optical packet switching (OPS) networks, access networks and datacenter networks. The line-rate detection algorithm relies on a simple-to-generate optical header, it is based on the fast Fourier transform (FFT) which can be efficiently implemented with the Goertzel algorithm, and it is insensitive to polarization rotations and frequency offset. Numerically, we demonstrate that performance in terms of packet detection rate (PER) can be tailored by controlling the sizes of the packet header and the line-rate estimator.

Non-orthogonal multiple access (NOMA) is a promising multiple access scheme for further improving the spectrum efficiency compared to orthogonal multiple access (OMA) in the 5th Generation (5G) mobile communication systems. As inter-user interference cancellers for NOMA, two kinds of receiver structures are considered. One is the reduced complexity-maximum likelihood receiver (R-ML) and the other is the codeword level interference canceller (CWIC). In this paper, we show that the R-ML is superior to the CWIC in terms of scheduling flexibility. In addition, we propose a link to system (L2S) mapping scheme for the R-ML to conduct a system level evaluation, and show that the proposed scheme accurately predicts the block error rate (BLER) performance of the R-ML. The proposed L2S mapping scheme also demonstrates that the system level throughput performance of the R-ML is higher than that for the CWIC thanks to the scheduling flexibility.

In this paper, a new effective C/N0 theoretical model for global navigation satellite system (GNSS) receiver is proposed, in the presence of continuous wave interference (CWI). The proposed model is derived based on an interesting finding, correlator may output direct current (DC) in the presence of CWI. The DC introduced by CWI eventually leads to increase of carrier power estimation. It is totally different from current assumption that interference just causes noise power increase after correlation. The proposed model is verified by simulation.

A high-image-rejection wireless receiver with an N-phase active RC complex filter is proposed and analyzed. Signal analysis shows that the double-conversion receiver with (N+N2) mixers corrects the gain and phase mismatches of the adjacent image. Monte Carlo simulations evaluate the relation between image-rejection performances and the dispersions of device parameters for the double-conversion wireless receiver. The Monte Carlo simulations show that the image rejection ratio of the adjacent image depends almost only on R and C mismatches in the complex filter.

Iterative channel estimation and decoding receivers have evolved over the years, most especially with Turbo and LPDC codes. Nevertheless, few works have determined the performance of symbol level Reed-Solomon (RS) codes in iterative receiver structures. The iterative channel estimation and symbol level RS decoding receiver structure found in literature concentrate on M-QAM systems over flat Rayleigh fading channels. In this paper, attention is focused on the performance of RS codes in iterative channel estimation and decoding receiver structures for Orthogonal Frequency Division Multiplexing (OFDM) systems on frequency-selective Rayleigh fading channels. Firstly, the paper extends the Koetter and Vardy (KV) RS iterative receiver structure over flat Rayleigh fading channels to frequency-selective Rayleigh fading channels. In addition, the paper develops a symbol level RS iterative receiver structure for OFDM systems on frequency-selective Rayleigh fading channels based on the Parity-check matrix Transformation Algorithm (PTA). The performance of the RS-KV and RS-PTA iterative receiver structures for OFDM systems are documented through computer simulation. The simulation results verify that both iterative receiver structures are suitable for real time RS OFDM wireless applications. The results also show that the developed RS-PTA iterative receiver structure is a low complexity and high performance alternative to the RS-KV iterative receiver structure.

A wideband noise-cancelling receiver front-end is proposed in this brief. As a basic architecture, a low-noise transconductance amplifier, a passive mixer, and a transimpedance amplifier are employed to compose the wideband receiver. To achieve wideband input matching for the transconductor, a global feedback method is adopted. Since the wideband receiver has to minimize linearity degradation if a large blocker signal exists out-of-band, a linearization technique is applied for the transconductor circuit. The linearization cancels third-order intermodulation distortion components and increases linearity; however, the additional circuits used in linearization generate excessive noise. A noise-cancelling architecture that employs an auxiliary path cancels noise signals generated in the main path. The designed receiver front-end is fabricated using a 65-nm CMOS process. The receiver operates in the frequency range of 25 MHz-2 GHz with a gain of 49.7 dB. The in-band input-referred third-order intercept point is improved by 12.3 dB when the linearization is activated, demonstrating the effectiveness of the linearization technique.

In this paper, we propose to use a strategy for the two-user Gaussian X channel with limited receiver cooperation in the general case consisting of two parts: 1) the transmission scheme where the superposition coding is used and 2) the cooperative protocol where the two-round strategy based on quantize-map-and-forward (QMF) is employed. We image that a Gaussian X channel can be considered as a superposition of two Gaussian interference channels based on grouping of the sent messages from each transmitter to the corresponding receivers. Finally, we give an achievable rate region for the general case of this channel.