Recent years have seen a general resurgence of interest in analog signal processing and computing architectures. In addition, extensive theoretical and experimental literature on chaos and analog chaotic oscillators exists. One peculiarity of these circuits is the ability to generate, despite their structural simplicity, complex spatiotemporal patterns when several of them are brought towards synchronization via coupling mechanisms. While by no means a systematic survey, this paper provides a personal perspective on this area. After briefly covering design aspects and the synchronization phenomena that can arise, a selection of results exemplifying potential applications is presented, including in robot control, distributed sensing, reservoir computing, and data augmentation. Despite their interesting properties, the industrial applications of these circuits remain largely to be realized, seemingly due to a variety of technical and organizational factors including a paucity of design and optimization techniques. Some reflections are given regarding this situation, the potential relevance to discontinuous innovation in analog circuit design of chaotic oscillators taken both individually and as synchronized networks, and the factors holding back the transition to higher levels of technology readiness.

A method for bandwidth enhancement of radar cross section (RCS) reduction by metasurfaces was studied. Scattering cancellation is one of common methods for reducing RCS of target scatterers. It occurs when the wave scattered by the target scatterer and the wave scattered by the canceling scatterer are the same amplitude and opposite phase. Since bandwidth of scattering cancellation is usually narrow, we proposed the bandwidth enhancement method using metasurfaces, which can control the frequency dependence of the scattering phase. We designed and fabricated a metasurface composed of a patch array on a grounded dielectric substrate. Numerical and experimental evaluations confirmed that the metasurface enhances the bandwidth of 10dB RCS reduction by 52% bandwidth ratio of the metasurface from 34% bandwidth ratio of metallic cancelling scatterers.

Hardware accelerators are designed to support a specialized processing dataflow for everchanging deep neural networks (DNNs) under various processing environments. This paper introduces two hardware properties to describe the cost of data movement in each memory hierarchy. Based on the hardware properties, this paper proposes a set of evaluation metrics that are able to evaluate the number of memory accesses and the required memory capacity according to the specialized processing dataflow. Proposed metrics are able to analytically predict energy, throughput, and area of a hardware design without detailed implementation. Once a processing dataflow and constraints of hardware resources are determined, the proposed evaluation metrics quickly quantify the expected hardware benefits, thereby reducing design time.

Advanced information-processing services such as computer vision require a high-performance digital circuit to perform high-load processing at high speed. To achieve high-speed processing, several image-processing applications use an approximate computing technique to reduce idle time of the circuit. However, it is difficult to design the high-speed image-processing circuit while controlling the error rate so as not to degrade service quality, and this technique is used for only a few applications. In this paper, we propose a method that achieves high-speed processing effectively in which processing time for each task is changed by roughly detecting its completion. Using this method, a high-speed processing circuit with a low error rate can be designed. The error rate is controllable, and a circuit design method to minimize the error rate is also presented in this paper. To confirm the effectiveness of our proposal, a ripple-carry adder (RCA), 2-dimensional discrete cosine transform (2D-DCT) circuit, and histogram of oriented gradients (HOG) feature calculation circuit are evaluated. Effective clock periods of these circuits obtained by our method with around 1% error rate are improved about 64%, 6%, and 12%, respectively, compared with circuits without error. Furthermore, the impact of the miscalculation on a video monitoring service using an object detection application is investigated. As a result, more than 99% of detection points required to be obtained are detected, and it is confirmed the miscalculation hardly degrades the service quality.

In order to obtain high-performance circuits in advanced technology nodes, design methodology has to take the existence of large delay variations into account. Clock scheduling and speculative execution have overheads to realize them, but have potential to improve the performance by averaging the imbalance of maximum delay among paths and by utilizing valid data available earlier than worst-case scenarios, respectively. In this paper, we propose a high-performance digital circuit design method with speculative executions with less overhead by utilizing clock scheduling with delay insertions effectively. The necessity of speculations that cause overheads is effectively reduced by clock scheduling with delay insertion. Experiments show that a generated circuit achieves 26% performance improvement with 1.3% area overhead compared to a circuit without clock scheduling and without speculative execution.

This report focuses on an optimization scheme of advanced MOSFETs for designing CMOS circuits with high power efficiency. For this purpose the physics-based compact model HiSIM2 is applied so that the relationship between device and circuit characteristics can be investigated properly. It is demonstrated that the short-channel effect, which is usually measured by the threshold-voltage shift relative to long-channel MOSFETs, provides a consistent measure for device-performance degradation with reduced channel length. However, performance degradations of CMOS circuits such as the power loss cannot be predicted by the threshold-voltage shift alone. Here, the subthreshold swing is identified as an additional important measure for power-efficient CMOS circuit design. The increase of the subthreshold swing is verified to become obvious when the threshold-voltage shift is larger than 0.15V.

An output voltage-current equation of charge pump DC-DC voltage multiplier using diodes is provided to cover wide clock frequency and output current ranges for designing energy harvester operating at a near-threshold voltage or in sub-threshold region. Equivalent circuits in slow and fast switching limits are extracted. The effective threshold voltage of the diode in slow switching limit is also derived as a function of electrical characteristics of the diodes, such as the saturation current and voltage slope parameter, and design parameters such as the number of stages, capacitance per stage, parasitic capacitance at the top plate of the main boosting capacitor, and the clock frequency. The model is verified compared with SPICE simulation.

There have recently been more and more reports on CMOS integrated circuits operating at terahertz (≥ 0.1THz) frequencies. However, design environments and techniques are not as well established as for RF CMOS circuits. This paper reviews recent progress made by the authors in terahertz CMOS design for low-power and high-speed wireless communication, including device characterization and modeling techniques. Low-power high-speed wireless data transfer at 11Gb/s and 19pJ/bit and a 7-pJ/bit ultra-low-power transceiver chipset are presented.

This letter describes a design methodology for an arithmetic logic unit (ALU) incorporating reconfigurability based on double-gate carbon nanotube field-effect transistors (DG-CNTFETs). The design of a DG-CNTFET with an ambipolar-property-based reconfigurable static logic circuit is simple and straightforward using an ambipolar binary decision diagram (Am-BDD), which represents the cornerstone for the automatic pass transistor logic (PTL) synthesis flows of ambipolar devices. In this work, an ALU with 16 functions is synthesized by the design methodology of a DG-CNTFET-based reconfigurable static logic circuit. Furthermore, it is shown that the proposed ALU is much more flexible and practical than a conventional DG-CNTFET-based reconfigurable ALU.

This paper propose a structure of standard cells where the P/N boundary ratio of each cell can be independently customized for near-threshold operation. Lowering the supply voltage is one of the most promising approaches for reducing the power consumption of VLSI circuit, however, this causes an increase of imbalance between rise and fall delays for cells having transistor stacks. Conventional cell library with fixed P/N boundary is not efficient to compensate this delay imbalance. Proposed structure achieves individual P/N boundary ratio optimization for each standard cell, therefore it cancels the imbalance between rise and fall delays at the expense of cell area. Proposed structure is verified using measured result of Ring Oscillator circuits and simulation result of benchmark circuits in 65nm CMOS. The experiments with ISCAS'85 benchmark circuits demonstrate that the standard cell library consisting of the proposed cells reduces the power consumption of the benchmark circuits by 16% on average without increasing the circuit area, compared to that of the same circuit synthesized with a library which is not optimized for the near-threshold operation.

Ternary content addressable memory (TCAM) is becoming very popular for designing high-throughput forwarding engines on routers. However, TCAM has potential problems in terms of hardware and power costs, which limits its ability to deploy large amounts of capacity in IP routers. In this paper, we propose new hardware architecture for fast forwarding engines, called fast prefix search RAM-based hardware (FPS-RAM). We designed FPS-RAM hardware with the intent of maintaining the same search performance and physical user interface as TCAM because our objective is to replace the TCAM in the market. Our RAM-based hardware architecture is completely different from that of TCAM and has dramatically reduced the costs and power consumption to 62% and 52%, respectively. We implemented FPS-RAM on an FPGA to examine its lookup operation.

Evolvable hardware (EHW) is a new research field about the use of Evolutionary Algorithms (EAs) to construct electronic systems. EHW refers in a narrow sense to use evolutionary mechanisms as the algorithmic drivers for system design, while in a general sense to the capability of the hardware system to develop and to improve itself. Genetic Algorithm (GA) is one of typical EAs. We propose optimal circuit design by using GA with parameterized uniform crossover (GApuc) and with fitness function composed of circuit complexity, power, and signal delay. Parameterized uniform crossover is much more likely to distribute its disruptive trials in an unbiased manner over larger portions of the space, then it has more exploratory power than one and two-point crossover, so we have more chances of finding better solutions. Its effectiveness is shown by experiments. From the results, we can see that the best elite fitness, the average value of fitness of the correct circuits and the number of the correct circuits of GApuc are better than that of GA with one-point crossover or two-point crossover. The best case of optimal circuits generated by GApuc is 10.18% and 6.08% better in evaluating value than that by GA with one-point crossover and two-point crossover, respectively.

This paper presents an asynchronous design technique, an enabler for the emerging technology of flexible microelectronics that feature low-temperature processed polysilicon (LTPS) thin-film transistors (TFT) and surface-free technology by laser annealing/ablation (SUFTLA®). The first design instance chosen is an 8-bit microprocessor. LTPS TFTs are good for realizing displays having integrated VLSI circuit at lower costs. However, LTPS TFTs have drawbacks, including substantial deviations in characteristics and the self-heating phenomenon. To solve these problems, the authors adopted the asynchronous circuit design technique and developed an asynchronous design language called Verilog+, which is based on a subset of Verilog HDL® and includes minimal primitives used for describing the communications between modules, and the dedicated tools including a translator called xlator and a synthesizer called ctrlsyn. The flexible 8-bit microprocessor stably operates at 500 kHz, drawing 180 µA from a 5 V power source. The microprocessor's electromagnetic emissions are 21 dB less than those of the synchronous counterpart.

This paper presents a novel method to increase an impedance of a current source. The proposed circuit with a cascode and gain-boosting configuration is also presented. The operation has been confirmed by simulation using a 0.18 µm CMOS technology.

A new method of cancellation of IM3 using current feedback has been proposed for a multi-stage RFIC amplifier. In order to cancel the IM3 present in an output signal of the amplifier, the IIP3 level and IM3 phase of the amplifier are adjusted by means of feedback circuit techniques, so that the target specification is satisfied. By estimating the IIP3 level and IM3 phase variations for two states in situations with and without feedback possessing linear factors, the parameters of a feedback circuit can be calculated. To confirm the validity of the method, we have investigated two approaches; one including an analytical approach to designing a two-stage feedback amplifier, achieving an IIP3 level improvement of 14.8 dB. The other method involves the fabrication of single-stage amplifiers with and without feedback, operating at 850 MHz, both of which were designed as an integrated circuit using a 0.18 µm SiGe BiCMOS process. The fabricated IC's were tested using a load-pull measurement system, and a good agreement between the estimated and measured IIP3 level and IM3 phase variations has been achieved. Further studies show that the error in these variations, as estimated by the method, has been found to be less than 1.5 dB and 15 degrees, respectively, when the load admittance at 1701 MHz was greater than 1/50 S.

A complete system for the implementation of digital logic in a Field-Programmable Gate Array (FPGA) platform is introduced. The novel power-efficient FPGA architecture was designed and simulated in STM 0.18 µm CMOS technology. The detailed design and circuit characteristics of the Configurable Logic Block, the interconnection network, the switch box and the connection box were determined and evaluated in terms of energy, delay and area. A number of circuit-level low-power techniques were employed because power consumption was the primary concern. Additionally, a complete tool framework for the implementation of digital logic circuits in FPGA platforms is introduced. Having as input VHDL description of an application, the framework derives the reconfiguration bitstream of FPGA. The framework consists of: i) non-modified academic tools, ii) modified academic tools and iii) new tools. Furthermore, the framework can support a variety of FPGA architectures. Qualitative and quantitative comparisons with existing academic and commercial architectures and tools are provided, yielding promising results.

This paper presents CrtSmile--a CAD tool for the automatic extraction of layout-dependent substrate effects for RF MOSFET modeling. CrtSmile incorporates a new scalable substrate model, which depends not only on the geometric layout information of a transistor (the number of gate fingers, finger width, channel length and bulk contact location), but also on the transistor layout and bulk patterns. We show that this model is simple to extract and has good agreement with measured data for a 0.35 µm CMOS process. CrtSmile reads in the layout information of RF transistors in the CIF/GDSII format, performs a pattern-based layout extraction to recognize the transistor layout and bulk patterns. A scalable layout-dependent substrate model is automatically generated and attached to the standard BSIM3 device model as a sub-circuit for use in circuit simulation. A low noise amplifier is evaluated with the proposed CrtSmile tool, showing the importance of layout effects for RF transistor substrate modeling.

Utilizing a macromodel which calculates the floating gate potential by combining resistances and dependent voltage and current sources, DC transfer characteristics for multi-input neuron MOS inverters and for those in the neuron MOS full adder circuit are simulated both at room temperature and at 77 K. Based on the simulated results, low temperature circuit failures are discussed. Furthermore, circuit design parameter optimization both for low and room temperature operations is described.

This paper describes the realization of a dynamically reconfigurable logic LSI based on a novel parallel computer architecture. The key point of the architecture is its dual-structured cell array which enables dynamic and autonomous reconfiguration of the logic circuits. The LSI was completed by successfully introducing two specific features: fully asynchronous logic circuits and a homogeneous structure, only LUTs are used.

In this paper, we propose an improved network-flow based multi-way circuit partitioning algorithm whose objective is to minimize the number of sub-circuits. It iteratively extracts a size-maximal feasible sub-circuit one at a time. In our approach, two devices are applied. One is in the use of an exact min-cut graph, and the other is in the idea of keeping the number of I/O pins of the residual circuit as small as possible after one-time extraction. We implemented our algorithm in C for experiments, and tested it with several industrial cases and MCNC benchmarks. Compared to the known approach, we observed more than 10% reduction in average of the sub-circuit number.