We propose microwave heating via electromagnetic coupling using zeroth-order resonators (ZORs) to extend the uniform heating area. ZORs can generate resonant modes with a wavenumber of 0, which corresponds to an infinite guide wavelength. Under this condition, uniform heating is expected because the resulting standing waves would not have nodes or antinodes. In the design proposed in this paper, two ZORs fabricated on dielectric substrates are arranged to face each other for electromagnetic coupling, and a sample placed between the resonators is heated. A single ZOR was investigated using a 3D electromagnetic simulator, and the resonant frequency and electric field distribution of the simulated ZOR were confirmed to be in good agreement with those of the fabricated ZOR. Simulations of two ZORs facing each other were then conducted to evaluate the performance of the proposed system as a heating apparatus. It was found that a resonator spacing of 25 mm was suitable for uniform heating. Heating simulations of SiC and Al2O3 sheets were performed with the obtained structure. The heating uniformity was evaluated by the width L50% over which the power loss distribution exceeds half the maximum value. This evaluation index was equal to 0.397λ0 for SiC and 0.409λ0 for Al2O3, both of which exceed λ0/4, the distance between a neighboring node and antinode of a standing wave, where λ0 is the free-space wavelength. Therefore, the proposed heating apparatus is effective for uniform microwave heating. Because of the different electrical parameters of the heated materials, SiC can be easily heated, whereas Al2O3 heats little. Finally, heating experiments were performed on each of these materials. Good uniformity in temperature was obtained for both SiC and Al2O3 sheets.

The very high path loss caused by molecular absorption becomes the biggest problem in Terahertz (THz) wireless communications. Recently, the multi-band ultra-massive multi-input multi-output (UM-MIMO) system has been proposed to overcome the distance problem. In UM-MIMO systems, the impact of mutual coupling among antennas on the system performance is unable to be ignored because of the dense array. In this letter, a channel model of UM-MIMO communication system is developed which considers coupling effect. The effect of mutual coupling in the subarray on the functionality of the system has been investigated through simulation studies, and reliable results have been derived.

We study the device length and/or band characteristics examined by two coupling analysis methods for our proposed fiber-type polarization splitter (FPS) composed of single mode fiber and polarization maintaining fiber. The first method is based on the power transition characteristics of the coupled-mode theory (CMT), and the second, a more accurate analysis method, is based on improved fundamental mode excitation (IFME). The CMT and IFME were evaluated and investigated with respect to the device length and bandwidth characteristics of the FPS. In addition, the influence of the excitation point shift of the fundamental mode, which has not been almost researched so far, is also analysed by using IFME.

The misalignment of a coupler is a significant issue for capacitive wireless power transfer (WPT). This paper presents a capacitive WPT system specifically designed for underwater drones operating in flowing freshwater environments. The primary design features include a capacitive coupler with an opposite relative position between feeding and receiving points on the coupler electrode, two phase compensation circuits, and a load-independent inverter. A stable and energy-efficient power transmission is achieved by maintaining a 90° phase difference on the coupler electrode in dielectrics with a large unloaded quality factor (Q factor), such as in freshwater. Although a 622-mm coupler electrode is required at 13.56MHz, the phase compensation circuits can reduce to 250mm as one example, which is mountable to small underwater drones. Furthermore, the electricity waste is automatically reduced using the constant-current (CC) output inverter in the event of misalignment where efficiency drops occur. Finally, their functions are simulated and demonstrated at various receiver positions and transfer distances in tap water.

This study proposed a novel decoupling method for four planar inverted-F antennas (PIFAs) operating at 2.0GHz (f0). The edge-to-edge and center-to-center spacings of the adjacent PIFAs are extremely small (0.05λ0 and 0.17λ0, respectively), resulting in strong mutual coupling among them. In our previous study, we proposed a structure consisting of parasitic elements (PEs) and a bridge line (BL) for the decoupling of two PIFAs. One attractive feature of the proposed method is that no adjustment of the original structure and size of the PIFAs is necessary. However, as the number of PIFAs increases to four, their decoupling becomes considerably more complicated, and impedance mismatch is also an issue to be considered. Therefore, in this study, PEs and BLs are functionally developed to simultaneously achieve low mutual coupling and improved impedance matching of the four PIFAs. The simulated results showed that loading the proposed PEs and BLs onto the four PIFAs could reduce as well as maintain all mutual coupling for less than -10dB, and simultaneously improve impedance matching. Therefore, the total antenna efficiency at 2.0GHz could be significantly improved from 64.2% to 84.8% for PIFA1 and PIFA4, and from 35.9% to 74.2% for PIFA2 and PIFA3. Four PIFAs with PEs and BLs were fabricated and measured to validate the simulation results.

This paper describes an in-depth analysis of crosstalk in a high-bandwidth 3D-stacked memory using a multi-hop inductive coupling interface and proposes two countermeasures. This work analyzes the crosstalk among seven stacked chips using a 3D electromagnetic (EM) simulator. The detailed analysis reveals two main crosstalk sources: concentric coils and adjacent coils. To suppress these crosstalks, this paper proposes two corresponding countermeasures: shorted coils and 8-shaped coils. The combination of these coils improves area efficiency by a factor of 4 in simulation. The proposed methods enable an area-efficient inductive coupling interface for high-bandwidth stacked memory.

Mutual coupling between antenna array elements will significantly degrade the performance of the array signal processing methods. Due to the Toeplitz structure of mutual coupling matrix (MCM), there exist some mutual coupling calibration algorithms for the uniform linear array (ULA) or uniform circular array (UCA). But few methods for other arrays. In this letter, we derive a new transformation formula for the MCM of the 7-elements hexagonal array (HA-7). Further, we extend two mutual coupling auto-calibration methods from UCA to HA by the transformation formula. Simulation results demonstrate the validity of the proposed two methods.

An aperture-shared multi-port waveguide antenna with multiple feeds is presented in this paper. The antenna consists of sequentially rotated four traditional WR-28 waveguides at 28GHz so as to create a multi-polarized function with decoupling between the ports. In addition, a rectangular DR (Dielectric resonator) is mounted at the center of the four apertures to obtain lower mutual coupling over a wide band and to suppress the cross-polarization in the antenna boresight direction. The proposed antenna achieves high gain of 14.4dBi, low mutual coupling of ≤-20dB on average, sufficient cross-polarization discrimination level at ≃20dB in the 27-29GHz frequency band.

Couplers in a film-type capacitive wireless power charging (CWC) system for an implantable medical device were designed and analyzed in this work. Due to the high conductivity of the human body, two paths contribute to the power transmission, namely a high-frequency current and an electric field. This was confirmed by an equivalent circuit of the system. During analysis of the system, we used pig skin with subcutaneous fat, which has a high affinity with the human body, to search for a highly efficient electrode shape. Subsequently, we fabricated the designed coupler and measured ηmax. An ηmax of 56.6% was obtained for a half-circular coupler with a radius of 20 mm and a distance of 10 mm between adjacent couplers. This study will contribute to the realization of implantable devices that can be recharged during breaks or while sleeping at home and is expected to significantly reduce the burden on patients.

To reduce mutual coupling of a two-level nested array (TLNA) with an even number of sensors, we propose an improved array configuration that exhibits all the good properties of the prototype optimal configuration under the constraint of a fixed number of sensors N and achieves reduction of mutual coupling. Compared with the prototype optimal TLNA (POTLNA), which inner level and outer level both have N/2 sensors, those of the improved optimal TLNA (IOTLNA) are N/2-1 and N/2+1. It is proved that the physical aperture and uniform degrees of freedom (uDOFs) of IOTLNA are the same as those of POTLNA, and the number of sensor pairs with small separations of IOTLNA is reduced. We also construct an improved optimal second-order super nested array (SNA) by using the IOTLNA as the parent nested array, termed IOTLNA-SNA, which has the same physical aperture and the same uDOFs, as well as the IOTLNA. Numerical simulations demonstrate the better performance of the improved array configurations.

To realize a stable and efficient wireless power transfer (WPT) system that can be used in any environment, it is necessary to inspect the influence of environmental interference along the power transmission path of the WPT system. In this paper, attempts have been made to reduce the influence of the medium with a dielectric and conductive loss on the WPT system using spiral resonators for resonator-coupled type wireless power transfer (RC-WPT) system. An important element of the RC-WPT system is the resonators because they improve resonant characteristics by changing the shape or combination of spiral resonators to confine the electric field that mainly causes electrical loss in the system as much as possible inside the resonator. We proposed a novel dual-spiral resonator as a candidate and compared the basic characteristics of the RC-WPT system with conventional single-spiral and dual-spiral resonators. The parametric values of the spiral resonators, such as the quality factors and the coupling coefficients between resonators with and without a lossy medium in the power transmission path, were examined. For the lossy mediums, pure water or tap water filled with acryl bases was used. The maximum transmission efficiency of the RC-WPT system was then observed by tuning the matching condition of the system. Following that, the transmission efficiency of the system with and without lossy medium was investigated. These inspections revealed that the performance of the RC-WPT system with the lossy medium using the modified shape spiral resonator, which is the dual-spiral resonator proposed in our laboratory, outperformed the system using the conventional single-spiral resonator.

In this paper, an ultra-thin wave absorber using a resistive patch array closely-placed in front of a back-metal is designed. The positively large susceptance is required for the patch array to cancel out the negatively large input susceptance of the short-circuited ultra-thin spacer behind the array. It is found that the array needs the gap of 1mm, sheet resistance of less than 20Ω/sq. and patch width of more than 15mm to obtain the zero input susceptance of the absorber with the 1/30 wavelength spacer. Moreover, these parameters were designed considering the electromagnetic coupling between the array and back-metal, and the square patch array absorbers with the thickness from 1/30 to 1/150 wavelength were designed.

In this study, a novel decoupling method using parasitic elements (PEs) connected by a bridge line (BL) for two planar inverted-F antennas (PIFAs) is proposed. The proposed method is developed from a well-known decoupling method that uses a BL to directly connect antenna elements. When antenna elements are connected directly by a BL, strong mutual coupling can be reduced, but the resonant frequency shifts to a different frequency. Hence, to shift the resonant frequency toward the desired frequency, the original size of the antenna elements must be adjusted. This is disadvantageous if the method is applied in cases where the design conditions render it difficult to connect the antennas directly or adjust the original antenna size. Therefore, to easily reduce mutual coupling in such a case, a decoupling method that does not require both connecting antennas directly and adjusting the original antenna size is necessitated. This study demonstrates that using PEs connected by a BL reduces the mutual coupling from -6.6 to -14.1dB, and that the resonant frequency is maintained at the desired frequency (2.0GHz) without having to adjust the original PIFAs size. In addition, impedance matching can be adjusted to the desired frequency, resulting in an improved total antenna efficiency from 77.4% to 94.6%. This method is expected to be a simple and effective approach for reducing the mutual coupling between larger numbers of PIFA elements in the future.

This paper presents a method to optimize 2-D sparse array configurations along with a technique to interpolate holes to accurately estimate the direction of arrival (DOA). Conventional 2-D sparse arrays are often defined using a closed-form representation and have the property that they can create hole-free difference co-arrays that can estimate DOAs of incident signals that outnumber the physical elements. However, this property restricts the array configuration to a limited structure and results in a significant mutual coupling effect between consecutive sensors. In this paper, we introduce an optimization-based method for designing 2-D sparse arrays that enhances flexibility of array configuration as well as DOA estimation accuracy. We also propose a method to interpolate holes in 2-D co-arrays by nuclear norm minimization (NNM) that permits holes and to extend array aperture to further enhance DOA estimation accuracy. The performance of the proposed optimum arrays is evaluated through numerical examples.

Capacitive coupling of line coded and DC-balanced digital signals is often used to eliminate steady bias current flow between the systems or components in various communication systems. A multi-layer ceramic chip capacitor is promising for the capacitor of very broadband signal coupling because of its high frequency characteristics expected from the downsizing of the chip recent years. The lower limit of the coupling bandwidth is determined by the capacitance while the higher limit is affected by the parasitic inductance associated with the chip structure. In this paper, we investigate the coupling characteristics up to millimeter wave frequencies by the measurement and simulations. A phenomenon has been found in which the change in the current distribution in the chip structure occur at high frequencies and the coupling characteristics are improved compared to the prediction based on the conventional equivalent circuit model. A new equivalent circuit model of chip capacitor that can express the effect of the improvement has been proposed.

Smaller antenna structures for long-range radar transmitters and receivers operating in the 77-GHz band for automotive application have been achieved by using antennas with a horn, lens, and microstrip antenna. The transmitter (Tx) antenna height was reduced while keeping the antenna gain high and the antenna substrate small by developing an antenna structure composed of two differential horn and lens antennas in which the diameter and focus distance of the lenses were half those in the previous design. The microstrip antennas are directly connected to the differential outputs of a monolithic microwave integrated circuit. A Tx antenna fabricated using commercially available materials was 14mm high and had an output-aperture of 18×44mm. It achieved an antenna gain of 23.5dBi. The antenna substrate must be at least 96mm2. The antenna had a flat beam with half-power elevation and azimuth beamwidths of 4.5° and 21°, respectively. A receiver (Rx) antenna array composed of four sets of horn and lens antennas with an output-aperture of 9×22mm and a two-by-two array configuration was fabricated for application in a newly proposed small front-end module with azimuth direction of arrival (DOA) estimation. The Rx antenna array had an antenna coupling of less than -31dB in the 77-GHz band, which is small enough for DOA estimation by frequency-modulated continuous wave radar receivers even though the four antennas are arranged without any separation between their output-apertures.

Chipless tag systems composed of multimode stepped impedance resonators (SIRs) and a reader based on near-field electromagnetic coupling have been reported. This resonator structure has advantages including a simple design due to its symmetrical structure and good discrimination accuracy because many higher-order mode resonant frequencies can be used for identification of codes. However, in addition to the disadvantage of long resonator length, the frequency response in the tag system becomes unstable due to deterioration of the isolation between the probes because the same probe structure is used for the excitor and detector. In this paper, we propose two methods to solve these problems. One is to adopt an asymmetrical SIR structure with a short-circuited end and open-circuited end, which reduces the resonator length by half while allowing the same number of codes to be generated. The other is to improve isolation between probes by applying different magnetic field and electric field structures to the two probes for excitation and detection. We also examined assignment and identification conditions and clarified that the available number of codes for a unit tag can be more than 15 bits. It becomes clear that a 75-bit chipless tag on a credit card-sized (55×86mm) printed circuit board can be designed by integrating five unit tags.

This paper presents the feasibility of a capacitive coupler utilizing an electric double layer for wireless power transfer under seawater. Since seawater is an electrolyte solution, an electric double layer (EDL) is formed on the electrode surface of the coupler in direct current. If the EDL can be utilized in radio frequency, it is possible that high power transfer efficiency can be achieved under seawater because a high Q-factor can be obtained. To clarify this, the following steps need taking; First, measure the frequency characteristics of the complex permittivity in seawater and elucidate the behaviors of the EDL from the results. Second, clarify that EDL leads to an improvement in the Q-factor of seawater. It will be shown in this paper that capacitive coupling by EDL occurs using two kinds of the coupler models. Third, design a coupler with high efficiency as measured by the Q-factor and relative permittivity of EDL. Last, demonstrate that the designed coupler under seawater can achieve over 85% efficiency at a transfer distance of 5 mm and feasibility of the coupler with EDL.

MIMO technology, which uses multiple antennas, has been introduced to the mobile terminal to increase communication capacity per unit frequency. However, MIMO suffers from the problem of mutual coupling. If MIMO antennas are closely packed, as in a small wireless terminal, a strong mutual coupling occurs. The mutual coupling degrades radiation efficiency and channel capacity. As modern terminals are likely to use three MIMO antennas, reducing the mutual coupling 3×3 MIMO is essential. Some decoupling methods for three elements have been proposed. Unfortunately, these methods demand that the elements be cross-wired, which complicates fabrication and raises the cost. In this paper, we propose a non-connected decoupling method that uses short stubs and an insertion inductor and confirms that the proposed model offers excellent decoupling and increased radiation efficiency.

In recent years, MIMO technology which uses multiple antennas has been introduced to the mobile terminal to increase communication capacity per unit frequency. However, if MIMO antennas are put closely, a strong mutual coupling occurred. Moreover, CA which uses multiple frequencies is also utilized to improve communication speed. Therefore, reducing mutual coupling in multiple frequencies is required. In this paper, we propose a dual-band decoupling method by using a short stub and a branch element and confirmed that the proposed model performed decoupling, increased radiation efficiency.