Kudekar et al. proved an interesting result in low-density parity-check (LDPC) convolutional codes: The belief-propagation (BP) threshold is boosted to the maximum-a-posteriori (MAP) threshold by spatial coupling. Furthermore, the authors showed that the BP threshold for code-division multiple-access (CDMA) systems is improved up to the optimal one via spatial coupling. In this letter, a phenomenological model for elucidating the essence of these phenomenon, called threshold improvement, is proposed. The main result implies that threshold improvement occurs for spatially-coupled general graphical models.

As an add-on device option for the ultra-low power CMOS technology, the double-gated vertical-channel Tunnel Field-Effect Transistors (TFETs) of different source configurations are comparatively studied from the perspectives of fabrication and current drivability. While the top-source design where the source of the device is placed on the top of the fin makes the fabrication and source engineering much easier, it is more susceptible to parasitic resistance issue. The bottom-source design is difficult to engineer the tunneling barrier and may require a special replacement technique. Examples of the schemes to engineer the tunneling barrier for the bottom-source TFET are suggested. A TCAD simulation study on the bottom-source devices shows that both the parasitic resistance of source region and the current enhancement mechanism by field coupling need be carefully considered in designing the source.

Wafer-level testing is a well established solution for detecting manufacturing errors and removing non-functional devices early in the fabrication process. Recently this technique has been facing a number of challenges, resulting from increased complexity of devices under test, larger number and higher density of pads or bumps, application of mechanically fragile materials, such as low-k dielectrics, and ever developing packaging technologies. Most of these difficulties originate from the use of mechanical probes, as they limit testing speed, impose performance limitations and add reliability issues. Earlier work focused on relaxing these constraints by removing mechanical probes for data transmission and DC signal measurement and replacing them with non-contact interfaces. In this paper we extend this concept by adding a capability of transferring power wirelessly, enabling non-contact wafer-level testing. In addition to further improvements in the performance and reliability, this solution enables new testing scenarios such as probing wafers from their backside. The proposed system achieves 6 W/25 mm2 power transfer density over a distance of up to 0.32 mm, making it suitable for non-contact wafer-level testing of medium performance CMOS integrated circuits.

In this paper, the author proposes an electromagnetic coupling fed inverted-FL antenna design. The inverted-FL antenna with a self-complementary structure has been reported as a way to achieve a constant impedance of 188 ohms without the need for a matching load, since the axially symmetric self-complementary antenna has constant impedance, even though it has a finite structure. This design has been realized by integrating an inverted-F antenna with a self-complementary structure for achieving a broadband characteristic and an inverted-L element for operation on a frequency lower than the minimum frequency of the antenna. The proposed antenna realizes a broadband characteristic without attaching the matching load and the impedance transformer to match 50 ohms. The impedance transformer necessary for the inverted-FL antenna with a self-complementary structure is removed by using an electromagnetic coupling feed structure. This antenna, which has a volume of 101045 mm3, obtained broadband and multi-band characteristics covering the GSM850/GSM900/DCS/PCS/UMTS2100/UMTS2600 bands and the 2.5 G/3.5 G bands for Mobile-WiMAX in simulation and measurement.

A novel half mode elliptic substrate integrated waveguide (HMESIW) filter with bypass coupling substrate integrated circular cavity (BCSICC) is proposed and fabricated by using standard PCB technology. Due to the use of an elliptical waveguide cavity, the tolerance sensitivity of the filter is reduced. The filter optimizing procedure is therefore simplified. The measured results demonstrate its superior performance in tolerance sensitivity and show good agreements with the simulation results.

A planar high-pass filter (HPF) by using cross-couplings in multi-layer structure is proposed in this paper. The HPF consists of parallel plate and gap type capacitors and inductor lines on the bottom conductor. The one block of the HPF has a ladder T-section in the bridge T configuration. The one block HPF is, thus, coarsely designed in the manner of the proto-type HPF and the performance is optimized by circuit simulator. With the gap capacitor adjusted the proposed HPF illustrates the steep slope characteristics near the cut-off frequency by the attenuation pole. In order to improve the stopband performance, the cascaded two block HPF is examined. Its measured results show the good agreement with the simulated ones giving the second attenuation pole by an inductive cross-coupling.

Diffraction field by a wide and thick slit on a conducting screen has been analyzed. High frequency ray-mode coupling analysis has been utilized, and the total diffracted or radiated field in each region is considered as a summation of successive modal radiation contribution due to the original modal excitation by the incident plane wave. Our derived results are compared with those obtained by other solutions, and good agreement has been observed, and the validity of our formulation is confirmed.

In this paper, a simple type of printed dipole is proposed for Multi-Input Multi-Output (MIMO) applications in cognitive radio. The antenna is composed of a transmission line and a dipole. Some examinations of key factors and optimized parameters of the antenna are presented. The measured results illustrate that the proposed antenna offers a bandwidth of over 50% for Voltage Standing Wave Ratio (VSWR) less than 2, extending from 2.4 GHz to 4.0 GHz. The antenna peak gain in E-plane and radiation patterns at different frequencies are also explored. In addition, based on the proposed antenna, we introduce two simple broadband arrays for MIMO applications in cognitive radio. One has two ports and the other has four ports. Measurement results indicate that the arrays also work in a broad bandwidth. Mutual couplings between ports in each array are kept under -10 dB at the low frequencies and under -20 dB at the high frequencies of bandwidth of the arrays. Furthermore, we utilized the antenna arrays for some MIMO experiments to estimate the channel capacity in a wide frequency range.

Kudekar et al. recently proved that for transmission over the binary erasure channel (BEC), spatial coupling of LDPC codes increases the BP threshold of the coupled ensemble to the MAP threshold of the underlying LDPC codes. One major drawback of the capacity-achieving spatially-coupled LDPC codes is that one needs to increase the column and row weight of parity-check matrices of the underlying LDPC codes. It is proved, that Hsu-Anastasopoulos (HA) codes and MacKay-Neal (MN) codes achieve the capacity of memoryless binary-input symmetric-output channels under MAP decoding with bounded column and row weight of the parity-check matrices. The HA codes and the MN codes are dual codes each other. The aim of this paper is to present an empirical evidence that spatially-coupled MN (resp. HA) codes with bounded column and row weight achieve the capacity of the BEC. To this end, we introduce a spatial coupling scheme of MN (resp. HA) codes. By density evolution analysis, we will show that the resulting spatially-coupled MN (resp. HA) codes have the BP threshold close to the Shannon limit.

This paper presents a current-reused quadrature voltage-controlled oscillator (QVCO) which adopts a source-connection coupling structure. The QVCO simultaneously achieves low phase noise and low power consumption by newly combining current-reused VCOs and coupling transistors. The measured QVCO obtains good FoM of -188.2 dBc at a frequency of 2.2 GHz with 3.96 mW power consumption.

A 0.8-V CMOS Phase-Locked Loop (PLL) has been designed and fabricated by using a 0.13-µm 1p8m CMOS process. In the proposed PLL, the double-positive-feedbacks voltage-controlled oscillator (DPF-VCO) is used to generate current signals for the coupling current-mode injection-locked frequency divider (CCMILFD) and current-injection current-mode logic (CICML) divider. A short-pulsed-reset phase frequency detector (SPR-PFD) with the reduced pulse width of reset signal to improve the linear range of the PFD and a complementary-type charge pump to eliminate the current path delay are also adopted in the proposed PLL. The measured in-band phase noise of the fabricated PLL is -98 dBc/Hz. The locking range of the PLL is from 22.6 GHz to 23.3 GHz and the reference spur level is -69 dBm that is 54 dB bellow the carrier. The power consumption is 9.2 mW under a 0.8-V power supply. The proposed PLL has the advantages of low phase noise, low reference spur, and low power dissipation at low voltage operation.

This paper presents the design of a wideband low noise amplifier (LNA) for the 3GPP LTE (3rd Generation Partnership Project Long Term Evolution) standard. The proposed LNA uses a common gate topology with a noise cancellation technique for wideband (0.7 to 2.7 GHz) and low noise operation. The capacitive cross coupling technique is adopted for the common gate amplifier. Consequently input matching is achieved with lower transconductance, thereby reducing the power consumption and noise contribution. The LNA is designed in a 0.18 µm process and the simulations show lower than -10 dB input return loss (S11), and 2.42.6 dB noise figure (NF) over the entire operating band (0.72.7 GHz) while drawing 9 mA from a 1.8 V supply.

A capacitive coupling wireless connector circuit is implemented with 50 µm 50 µm pads, which is a 25X reduction of pad size compared with previous wireless connectors by allowing contacting and non-contacting modes. The proposed track and charge scheme allows both contacting and non-contacting communication through PCB capacitive pads. By making the precharge level of the input VDD or VSS, instead of 1/2 VDD, the time necessary to precharge is reduced. The proposed digitally tunable comparator does not require analog voltages, reduces the power to less than 1/20 at lower frequencies compared to previous capacitive coupling receivers. A test chip successfully transmitted and received 1 Gb/s, 27-1PRBS signal at 1 mW while increasing design freedom of the wireless connectors.

This paper presents measurement of on-chip coupling between PA and LNA integrated on Si CMOS substrate, which is caused by substrate coupling, magnetic coupling, power-line coupling, etc. These components are decomposed by measurements using diced chips. The result reveals that the substrate coupling is the most dominant in CMOS chips and the total isolation becomes less than -50 dB with more than 0.4 mm PA-to-LNA distance.

An area efficiency hybrid decoupling scheme is proposed to suppress the charge pump noise during F-N tunneling program in non-volatile memory (NVM). The proposed scheme is focused on suppressing the average noise power in frequency domain aspect, which is more suitable for the program error reduction in NVMs. The concept of active capacitor is utilized. Feed forward effect of the amplifier is firstly considered in the impedance analysis, and a trade-off relation between in-band and out-band frequency noise decoupling performance is shown. A fast optimization based on average noise power is made to achieve minimum error in the F-N tunneling program. Simulation results show very stable output voltage in different load conditions, the average ripple voltage is 17 mV with up to 20 dB noise-suppression-ratio (NSR), and the F-N tunneling program error is less than 5 mV for a 800 µs program pulse. A test chip is also fabricated in 0.18 µm technology. The area overhead of the proposed scheme is 2%. The measurement results show 24.4 mV average ripple voltage compared to 72.3 mV of the conventional one with the same decoupling capacitance size, while the noise power suppression achieves 15.4 dB.

The fabricated 1.55 µm high power superluminescent light emitting diodes (SLEDs) with 115 mW maximum output power and 3 dB bandwidth of 50 nm, using active multi-mode interferometer (MMI), showed high coupling efficiency of 66% into single-mode fiber, which resulted in maximum fiber-coupled power of 77 mW.

In this study, we propose a method to reduce the mutual coupling between two J-shaped folded monopole antennas (JFMAs), which cover the IEEE 802.11 b/g (2400-2484 MHz) band. First, the change in mutual coupling with the spacing between the two antenna elements is investigated by considering two feeding models, and the effects of changes in the coupling on the antenna efficiency are studied. Subsequently, we try the method to reduce mutual coupling, the method involves the use of a bridge line that links the two antennas. The mutual coupling can be significantly reduced and the total antenna efficiency can be improved by linking two shorting strips with the bridge line. In a past study, we had found that in the case of L-shaped folded monopole antennas (LFMAs), the mutual coupling and antenna efficiency vary with the linking location on the bridge line. Moreover, we compare the characteristics of the LFMA and JFMA and show that the JFMA is effective when miniaturized.

This letter studies a pulse-coupled system constructed by delayed cross-switching between two bifurcating neurons. The system can exhibit an interesting bifurcation: the delay-coupling can change chaotic behavior of single neurons into stable periodic behavior. Using the 1D phase map, it is clarified that the phenomenon is caused by the tangent bifurcation for the delay parameter. Presenting a simple test circuit, the phenomenon can be confirmed experimentally.

A half-cylindrical BK-7 prism/dielectric film with a grating/Ag film/fluorescent polymer film structure was prepared, and its surface plasmon (SP) excitation property was investigated. It was confirmed experimentally that SP excitations are possible in this structure by using prism and grating couplings. The SP excitation property depended on the direction of the grating vector. Furthermore, intense photoluminescence was observed when the SPs were simultaneously excited at the Ag/polymer interface by prism coupling and at the Cytop/Ag interface by grating coupling.

Method of moments (MoM) is an efficient design and analysis method for waveguide slot arrays. A rectangular entire-domain basis function is one of the most popular approximations for the slot aperture fields. MoM with only one basis function does not provide sufficient accuracy and the use of higher order mode of basis functions is inevitable to guarantee accuracy. However, including the higher order modes in MoM results in a rapid increase in the computational time as well as the analysis complexity; this is a serious drawback especially in the slot parameter optimization. The authors propose the slot correction length that compensates for the omission of higher order mode of basis functions. This length is constant for a wide range of couplings and frequency bands for various types of slots. The validity and universality of the concept of slot correction length are demonstrated for various slots and slot parameters. Practical slot array design can be drastically simplified by the use of MoM with only one basis function together with the slot correction length. As an example, a linear waveguide array of reflection-cancelling slot pairs is successfully designed.