In future deep space communication missions, VLBI (Very Long Baseline Interferometry) based on antenna array technology remains a critical detection method, which urgently requires the improvement of synthesis performance for antenna array signals. Considering this, focusing on optimizing the traditional antenna grouping method applied in the phase estimation algorithm, this letter proposes a “L/2 to L/2” antenna grouping method based on the maximum correlation signal-to-noise ratio (SNR). Following this idea, a phase difference estimation algorithm named “Couple” is presented. Theoretical analysis and simulation verification illustrate that: when ρ ＜ -10dB, the proposed “Couple” has the highest performance; increasing the number of antennas can significantly improve its synthetic loss performance and robustness. The research of this letter indicates a promising potential in supporting the rising deep space exploration and communication missions.

An optical mode multiplexer was newly designed and fabricated using LiNbO3 waveguides. The multiplexer consists of an asymmetric directional coupler capable of achieving the phase-matching condition by the voltage adjustment. The mode conversion efficiency between TM0 and TM1 modes was quantitatively measured to be 0.86 at maximum.

Although baud-rate clock and data recovery (CDR) such as Mueller-Müller (MM) CDR is adopted to ADC-based receivers (RXs), it suffers from false-lock points when the RXs handle PAM4 data pattern because of the absence of edge data. In this paper, a false-lock-aware locking scheme is proposed to address this issue. After the false-lock-aware locking scheme, a clock phase is adjusted to achieve maximum eye height by using a post-1-tap parameter for an FFE in the CDR loop. The proposed techniques are implemented in a 56-Gb/s PAM4 transceiver. A PLL uses an area-efficient “glasses-shaped” inductor. The RX comprises an AFE, a 28-GS/s 7-bit time-interleaved SAR ADC, and a DSP with a 31-tap FFE and a 1-tap DFE. A TX is based on a 7-bit DAC with a 4-tap FFE. The transceiver is fabricated in 16-nm CMOS FinFET technology, and achieves a BER of less than 1e-7 with a 30-dB loss channel. The measurement results show that the MM CDR escapes from false-lock points, and converges to near the optimum point for large eye height.

The fingerprint verification system is widely used in mobile devices because of fingerprint's distinctive features and ease of capture. Typically, mobile devices utilize small sensors, which have limited area, to capture fingerprint. Meanwhile, conventional fingerprint feature extraction methods need detailed fingerprint information, which is unsuitable for those small sensors. This paper proposes a novel fingerprint verification method for small area sensors based on deep learning. A systematic method combines deep convolutional neural network (DCNN) in a Siamese network for feature extraction and XGBoost for fingerprint similarity training. In addition, a padding technique also introduced to avoid wraparound error problem. Experimental results show that the method achieves an improved accuracy of 66.6% and 22.6% in the FingerPassDB7 and FVC2006DB1B dataset, respectively, compared to the existing methods.

In 5th generation (5G) and Beyond 5G mobile communication systems, it is expected that numerous antennas will be densely deployed to realize ultra-broadband communication and uniform coverage. However, as the number of antennas increases, total power consumption of all antennas will also increase, which leads to a negative impact on the environment and operating costs of telecommunication operators. Thus, it is necessary to simplify an antenna structure to suppress the power consumption of each antenna. On the other hand, as a way to realize ultra-broadband communication, millimeter waves will be utilized because they can transmit signals with a broader bandwidth than lower frequencies. However, since millimeter waves have a large propagation loss, a propagation distance is shorter than that of low frequencies. Therefore, in order to extend the propagation distance, it is necessary to increase an equivalent isotropic radiated power by beamforming with phased array antenna. In this paper, a phased antenna array module in combined with analog radio over fiber (A-RoF) technology for 40-GHz millimeter wave is developed and evaluated for the first time. An 8×8 phased array antenna for 40-GHz millimeter wave with integrated photodiodes and RF chains has been developed, and end-to-end transmission experiment including 20km A-RoF transmission and 3-m over-the-air transmission from the developed phased array antenna has been conducted. The results showed that the 40-GHz RF signal after the end-to-end transmission satisfied the criteria of 3GPP signal quality requirements within ±50 degrees of main beam direction.

Recently, “Both-Side Retrodirective System” was proposed, as a beam convergence technique, for microwave high power transmission. To demonstrate the effectiveness of the both-side retrodirective system by experiment, the authors propose a 2-dimensional measurement equipment. Propagation in the parallel plate waveguide was analogized based on free-space propagation, and the theory and characteristics were clarified by simulation. The electric field distribution in the waveguide was measured by electric probe with the proposed equipment. Two types of measurement equipment were developed. One is a 4-element experiment system, which is a small-scale device for principle verification. The other is a 16-element measurement equipment, which is intended to evaluate beam convergence of a both-side retrodirective system in the next step. The measured results were compared with simulation results. As a result, it was confirmed that the beam formed in the waveguide was successfully measured. Thus, the effectiveness of 2-dimensional measurement equipment for evaluation of beam convergence was shown.

This paper demonstrates a phase compensation technique using varactors for variable-gain phase shifters (VGPSs). The VGPS consists of an I/Q generator and I/Q variable gain amplifiers (I/Q VGAs). I/Q VGAs based on common-emitter stages are enabled to control the gain by adjusting the collector current of the transistor. However, the phase control performance degenerates because the input capacitance varies with the collector current. The proposed phase compensation technique reduces the variation in the insertion phase of the I/Q VGA by adjusting the voltage of the varactor provided at its input and maintaining the input capacitance constant in any gain state. As a result, the VGPS can provide a low phase and amplitude error under phase control. A Ka-band VGPS with the proposed phase compensation technique, fabricated in a 130-nm SiGe BiCMOS process, demonstrates a 0.73° and 0.06 dB improvement in the RMS phase and amplitude error compared with the case without the compensation technique. The VGPS achieves measured RMS amplitude and phase errors of less than 0.19 dB and 0.75°, respectively, in an amplitude control range of more than 20 dB with a frequency range of 28 to 32 GHz.

The increasing demand for millimeter-wave (mmWave) frequencies with wider signal bandwidths, such as 5G NR, requires large investments on test equipment. This work presents a 5G mmWave up/down-converter with a 40 GHz LO, fabricated in custom PCBs with off-the-shelf components. The mmWave converter has broad IF and RF bandwidths of 1∼5 GHz and 21∼45 GHz, and the built-in LO generates 20∼29.5 GHz and 33.5∼40 GHz of output. To achieve high linearity of the converter simultaneously, the LO must produce low-phase-noise and be capable of high harmonics/spur rejection, and design techniques related to these features are demonstrated. Additionally, a reconfigurable IF amplifier for bi-directional conversion is included and demonstrates low gain variation to maintain the linearity of the wideband modulation signals. The final designed converter is tested with 5G OFDM 64-QAM 100 MHz 1-CC (4-CC) signals and shows RF/IF output power of -3/8 dBm with a linear range of 35 (30)/38 (33) dB at an EVM of 25 dB.

Precision microwave measurement systems require highly stable oscillators with both excellent long-term and short-term stability. Compared to components used in laboratory instruments, dielectric resonator oscillators (DRO) offer low phase noise with greatly reduced mechanical complexity. To further enhance performance, phase-locked loop (PLL) stabilization can be used to eliminate drift and provide precise frequency control. In this work, the design of a low-cost DRO concept is presented and its performance is evaluated through simulations and measurements. An open-loop phase noise of -107.2 dBc/Hz at 10 kHz offset frequency and 12.8 GHz output frequency is demonstrated. Drift and phase noise are reduced by a PLL, so that a very low jitter of under 29.6 fs is achieved over the entire operating bandwidth.

The optical phased array (OPA) is an emerging non-mechanical device that enables high-speed beam steering by emitting precisely phase-controlled lightwaves from numerous optical antennas. In practice, however, it is challenging to drive all phase shifters on an OPA in a deterministic manner due to the inevitable fabrication-induced phase errors and crosstalk between the phase shifters. In this work, we fabricate a 16-element silicon photonic non-redundant OPA chip with integrated phase monitors and experimentally demonstrate accurate monitoring of the relative phases of light from each optical antenna. Under the beam steering condition, the optical phase retrieved from the on-chip phase monitors varies linearly with the steering angle, as theoretically expected.

In this paper, we propose a hybrid crystal oscillator which achieves both quick startup and low steady-state power consumption. At startup, a large negative resistance is realized by configuring a Pierce oscillating circuit with a multi-stage inverter amplifier, resulting in high-speed startup. During steady-state oscillation, the oscillator is reconfigured as a class-C complementary Colpitts circuit for low power consumption and low phase noise. Prototype chips were fabricated in 65nm CMOS process technology. With Pierce-type configuration, the measured startup time and startup energy of the oscillator are reduced to 1/11 and 1/5, respectively, compared with the one without Pierce-type configuration. The power consumption during steady oscillation is 30 µW.

Series-connection of resonant-tunneling diodes (RTDs) has been considered to be efficient in upgrading the output power when it is introduced to oscillator architecture. This work is for clarifying the same architecture also contributes to increasing oscillation frequency because the device parasitic capacitance is reduced M times for M series-connected RTD oscillator. Although this mechanism is expected to be universal, we restrict the discussion to the recently proposed multiphase oscillator utilizing an RTD oscillator lattice loop. After explaining the operation principle, we evaluate how the oscillation frequency depends on the number of series-connected RTDs through full-wave calculations. In addition, the essential dynamics were validated experimentally in breadboarded multiphase oscillators using Esaki diodes in place of RTDs.

Direct-current superconducting quantum interference device (dc-SQUID) based on intrinsic Josephson junction (IJJ) has been fabricated using Bi2Sr2CaCu2O8+δ (Bi-2212) films grown on MgO substrates with surface steps. The superconducting loop parallel to the film surface across the step edge contains two IJJ stacks along the edge. The number of crystallographically stacked IJJ for each SQUIDs were 40, 18 and 3. Those IJJ SQUIDs except for one with 40 stacked IJJs revealed clear periodic modulation of the critical current for the flux quanta through the loops. It is anticipated that phase locking of IJJ has an effect on the modulation depth of the IJJ dc-SQUID.

Intrinsic Josephson junctions (IJJs) in the high-Tc cuprate superconductors have several fascinating properties, which are superior to the usual Josephson junctions obtained from conventional superconductors with low Tc, as follows; (1) a very thin thickness of the superconducting layers, (2) a strong interaction between junctions since neighboring junctions are closely connected in an atomic scale, (3) a clean interface between the superconducting and insulating layers, realized in a single crystal with few disorders. These unique properties of IJJs can enlarge the applicable areas of the superconducting qubits, not only the increase of qubit-operation temperature but the novel application of qubits including the macroscopic quantum states with internal degree of freedom. I present a comprehensive review of the phase dynamics in current-biased IJJs and argue the challenges of superconducting qubits utilizing IJJs.

This article presents a 28GHz high-accuracy phase and amplitude detection circuit for dual-polarized phased-array calibration. With dual-polarized calibration scheme, external LO signal is not required for calibration. The proposed detection circuit detects phase and amplitude independently, using PDC and ADC. By utilizing a 28GHz-to-140kHz downconversion scheme, the phase and amplitude are detected more accurately. In addition, reference signal for PDC and ADC is generated from 28GHz LO signal with divide-by-6 dual-step-mixing injection locked frequency divider (ILFD). This ILFD achieves 24.5-32.5GHz (28%) locking range with only 3.0mW power consumption and 0.01mm2 area. In the measurement, the detection circuit achieves phase and amplitude detections with RMS errors of 0.17degree and 0.12dB, respectively. The total power consumption of the proposed circuit is 59mW with 1-V supply voltage.

Recently, complex orthogonal variable spreading factor (OVSF) codes based on polyphase orthogonal codes have been proposed to support multi-user/multi-rate data transmission services in synchronous direct-sequence code-division multiple access (DS-CDMA) systems. This study investigates the low signal-envelope fluctuation property of the complex OVSF codes in terms of transmission signal trajectories. In addition, a new method is proposed to suppress the envelope fluctuation more strongly at the expense of reducing the number of spreading sequences of the codes.

Type-II Z-complementary pairs (ZCPs) play an important role in suppressing asynchronous interference in a wideband wireless communication system where the minimum interfering-signal delay is large. Based on binary Golay complementary pairs (BGCPs) and interleaving technique, new construction for producing Z-optimal Type-II even-length quadriphase ZCPs (EL-QZCPs) is presented, and the resultant pairs have new lengths in the form of 2 × 2α10β26γ (α, β, γ non-negative integers), which are not included in existing known Type-II EL-QZCPs.

Backscatter communication is an emerging wireless access technology to realize ultra-low power terminals exploiting the modulated reflection of incident radio wave. This paper proposes a method to measure the phase angle of backscatter link using principal component analysis (PCA). The phase angle measurement of backscatter link at the receiver is essential to maximize the signal quality for subsequent demodulation and to measure the distance and the angle of arrival. The drawback of popular phase angle measurement with naive phase averaging and linear regression analysis is to produce erroneous phase angle, where the phase angle is close to $pmrac{pi}{2}$ radian and the signal quality is poor. The advantage of the proposal is quantified with a computer simulation, a conducted experiment and radio propagation experiments.

In order to improve the frequency band utilization and avoid mutual interference between signals, the BD3 satellite signals adopt Binary Offset Carrier (BOC) modulation. On one hand, BOC modulation has a narrow main peak width and strong anti-interference ability; on the other hand, the phenomenon of false acquisition locking caused by the multi-peak characteristic of BOC modulation itself needs to be resolved. In this context, this paper proposes a new BOC(n,n) unambiguous acquisition algorithm based on segmentation reconstruction. The algorithm is based on splitting the local BOC signal into four parts in each subcarrier period. The branch signal and the received signal are correlated with the received signal to generate four branch correlation signals. After a series of combined reconstructions, the final signal detection function completely eliminates secondary peaks. A simulation shows that the algorithm can completely eliminate the sub-peak interference for the BOC signals modulated by subcarriers with different phase. The characteristics of narrow correlation peak are retained. Experiments show that the proposed algorithm has superior performance in detection probability and peak-to-average ratio.

Quadrature voltage-controlled oscillators (VCOs) with current-weight-average and voltage-weight-average phase-adjusting architectures are studied. The phase adjusting equalizes the oscillation frequency to the LC-resonant frequency. The merits of the equalization are explained by using Leeson's phase noise equation and the impulse sensitivity function (ISF). Quadrature VCOs with the phase-adjusting architectures are fabricated using 180-nm TSMC CMOS and show low-phase-noise performances compared to a conventional differential VCO. The ISF analysis and small-signal analysis also show that the drawbacks of the current-weight-average phase-adjusting and voltage-weight-average phase-adjusting architectures are current-source noise effect and large additional capacitance, respectively. A voltage-average-adjusting circuit with a source follower at its input alleviates the capacitance increase.