We propose microwave heating via electromagnetic coupling using zeroth-order resonators (ZORs) to extend the uniform heating area. ZORs can generate resonant modes with a wavenumber of 0, which corresponds to an infinite guide wavelength. Under this condition, uniform heating is expected because the resulting standing waves would not have nodes or antinodes. In the design proposed in this paper, two ZORs fabricated on dielectric substrates are arranged to face each other for electromagnetic coupling, and a sample placed between the resonators is heated. A single ZOR was investigated using a 3D electromagnetic simulator, and the resonant frequency and electric field distribution of the simulated ZOR were confirmed to be in good agreement with those of the fabricated ZOR. Simulations of two ZORs facing each other were then conducted to evaluate the performance of the proposed system as a heating apparatus. It was found that a resonator spacing of 25 mm was suitable for uniform heating. Heating simulations of SiC and Al2O3 sheets were performed with the obtained structure. The heating uniformity was evaluated by the width L50% over which the power loss distribution exceeds half the maximum value. This evaluation index was equal to 0.397λ0 for SiC and 0.409λ0 for Al2O3, both of which exceed λ0/4, the distance between a neighboring node and antinode of a standing wave, where λ0 is the free-space wavelength. Therefore, the proposed heating apparatus is effective for uniform microwave heating. Because of the different electrical parameters of the heated materials, SiC can be easily heated, whereas Al2O3 heats little. Finally, heating experiments were performed on each of these materials. Good uniformity in temperature was obtained for both SiC and Al2O3 sheets.

Space is becoming increasingly congested and contested, which calls for effective means to conduct effective monitoring of high-value space assets, especially in Space Situational Awareness (SSA) missions, while there are imperfections in existing methods and corresponding algorithms. To overcome such a problem, this letter proposes an algorithm for accurate Connected Element Interferometry (CEI) in SSA based on more interpolation information and iterations. Simulation results show that: (i) after iterations, the estimated asymptotic variance of the proposed method can basically achieve uniform convergence, and the ratio of it to ACRB is 1.00235 in δ0 ∈ [-0.5, 0.5], which is closer to 1 than the current best AM algorithms; (ii) In the interval of SNR ∈ [-14dB, 0dB], the estimation error of the proposed algorithm decreases significantly, which is basically comparable to CRLB (maintains at 1.236 times). The research of this letter could play a significant role in effective monitoring and high-precision tracking and measurement with significant space targets during futuristic SSA missions.

Graph dissimilarities provide a powerful and ubiquitous approach for applying machine learning algorithms to edge-attributed graphs. However, conventional optimal transport-based dissimilarities cannot handle edge-attributes. In this paper, we propose an optimal transport-based dissimilarity between graphs with edge-attributes. The proposed method, multi-dimensional fused Gromov-Wasserstein discrepancy (MFGW), naturally incorporates the mismatch of edge-attributes into the optimal transport theory. Unlike conventional optimal transport-based dissimilarities, MFGW can directly handle edge-attributes in addition to structural information of graphs. Furthermore, we propose an iterative algorithm, which can be computed on GPUs, to solve non-convex quadratic programming problems involved in MFGW.  Experimentally, we demonstrate that MFGW outperforms the conventional optimal transport-based dissimilarity in several machine learning applications including supervised classification, subgraph matching, and graph barycenter calculation.

Model-based sensorless control of permanent magnet synchronous motor (PMSM) is promising for high-speed operation to estimate motor state, which is the speed and the position of the rotor, via electric signals of the stator, beside the inevitable fact that estimation accuracy is degraded by electromagnet interference (EMI) from switching devices of the converter. In this paper, the simulation system based on Luenberger observer and phase-locked loop (PLL) has been established, analyzing impacts of EMI on motor state estimations theoretically, exploring influences of EMI with different cutoff frequency, rated speeds, frequencies and amplitudes. The results show that Luenberger observer and PLL have strong immunity, which enable PMSM can still operate stably even under certain degrees of interference. EMI produces sideband harmonics that enlarge pulsation errors of speed and position estimations. Additionally, estimation errors are positively correlated with cutoff frequency of low-pass filter and the amplitude of EMI, and negatively correlated with rated speed of the motor and the frequency of EMI.  When the frequency is too high, its effects on motor state estimations are negligible. This work contributes to the comprehensive understanding of how EMI affects motor state estimations, which further enhances practical application of sensorless PMSM.

In the field of machine learning security, as one of the attack surfaces especially for edge devices, the application of side-channel analysis such as correlation power/electromagnetic analysis (CPA/CEMA) is expanding. Aiming to evaluate the leakage resistance of neural network (NN) model parameters, i.e. weights and biases, we conducted a feasibility study of CPA/CEMA on floating-point (FP) operations, which are the basic operations of NNs. This paper proposes approaches to recover weights and biases using CPA/CEMA on multiplication and addition operations, respectively. It is essential to take into account the characteristics of the IEEE 754 representation in order to realize the recovery with high precision and efficiency. We show that CPA/CEMA on FP operations requires different approaches than traditional CPA/CEMA on cryptographic implementations such as the AES.

The misalignment of a coupler is a significant issue for capacitive wireless power transfer (WPT). This paper presents a capacitive WPT system specifically designed for underwater drones operating in flowing freshwater environments. The primary design features include a capacitive coupler with an opposite relative position between feeding and receiving points on the coupler electrode, two phase compensation circuits, and a load-independent inverter. A stable and energy-efficient power transmission is achieved by maintaining a 90° phase difference on the coupler electrode in dielectrics with a large unloaded quality factor (Q factor), such as in freshwater. Although a 622-mm coupler electrode is required at 13.56MHz, the phase compensation circuits can reduce to 250mm as one example, which is mountable to small underwater drones. Furthermore, the electricity waste is automatically reduced using the constant-current (CC) output inverter in the event of misalignment where efficiency drops occur. Finally, their functions are simulated and demonstrated at various receiver positions and transfer distances in tap water.

The novel patch element shapes with the interdigital and multi-via structures for mushroom-type metasurface reflectors are proposed for controlling the reflection phases. The interdigital structure provides a wide reflection phase range by changing the depth of the interdigital fingers. In addition, the multi-via structure provides the higher positive reflection phases such as near +180°. The sufficient reflection phase range of 360° and the low polarization dependent properties could be confirmed by the electromagnetic field simulation. The metasurface reflector for the normal incident plane wave was designed. The desired reflection angles and sharp far field patterns of the reflected beams could be confirmed in the simulation results. The prototype reflectors for the experiments should be designed in the same way as the primary reflector design of the reflector antenna. Specifically, the reflector design method based on the ray tracing method using the incident wave phase was proposed for the prototype. The experimental radiation pattern for the reflector antenna composed of the transmitting antenna (TX) and the prototype metasurface reflector was similar to the simulated radiation pattern. The effectiveness of the proposed structures and their design methods could be confirmed by these simulation and experiment results.

The art gallery problem is to find a set of guards who together can observe every point of the interior of a polygon P. We study a chromatic variant of the problem, where each guard is assigned one of k distinct colors. A chromatic guarding is said to be conflict-free if at least one of the colors seen by every point in P is unique (i.e., each point in P is seen by some guard whose color appears exactly once among the guards visible to that point). In this paper, we consider vertex-to-point guarding, where the guards are placed on vertices of P, and they observe every point of the interior of P. The vertex-to-point conflict-free chromatic art gallery problem is to find a colored-guard set such that (i) guards are placed on P's vertices, and (ii) any point in P can see a guard of a unique color among all the visible guards. In this paper, it is shown that determining whether there exists a conflict-free chromatic vertex-guard set for a polygon with holes is NP-hard when the number of colors is k=2.

Question answering (QA) systems are designed to answer questions based on given information or with the help of external information. Recent advances in QA systems are overwhelmingly contributed by deep learning techniques, which have been employed in a wide range of fields such as finance, sports and biomedicine. For generative QA in open-domain QA, although deep learning can leverage massive data to learn meaningful feature representations and generate free text as answers, there are still problems to limit the length and content of answers. To alleviate this problem, we focus on the variant YNQA of generative QA and propose a model CasATT (cascade prompt learning framework with the sentence-level attention mechanism). In the CasATT, we excavate text semantic information from document level to sentence level and mine evidence accurately from large-scale documents by retrieval and ranking, and answer questions with ranked candidates by discriminative question answering. Our experiments on several datasets demonstrate the superior performance of the CasATT over state-of-the-art baselines, whose accuracy score can achieve 93.1% on IR&QA Competition dataset and 90.5% on BoolQ dataset.

For dichromats to receive the information represented in color images, it is important to study contrast improvement methods and quantitative evaluation indices of color conversion results. There is an index to evaluate the degree of contrast improvement and in this index, the contrast for dichromacy caused by the lightness component is given importance. In addition, random sampling was introduced in the computation of this index. Although the validity of the index has been shown through comparison with a subjective evaluation, it is considered that the following two points should be examined. First, should contrast for normal trichromacy caused by the lightness component also be attached importance. Second, the influence of random sampling should be examined in detail. In this paper, a new index is proposed and the above-mentioned points are examined. For the first point, the following is revealed through experiment. Consideration of the contrast for normal trichromacy caused by a lightness component that is the same as that for dichromacy may or may not result in a good outcome. The evaluation performance of the proposed index is equivalent to that of the previous index overall. It can be said that the proposed index is superior to the previous one in terms of the unity of evaluating contrast. For the second point, the computation time and the evaluation of significant digits are shown. In this paper, a sampling number such that the number of significant digits can be considered as three is used. In this case, the variation caused by random sampling is negligible compared with the range of the proposed index, whereas the computation time is about one-seventh that when the sampling is not adopted.

To achieve the extreme high data rate and extreme coverage extension requirements of 6G wireless communication, new spectrum in sub-THz (100-300GHz) and non-terrestrial network (NTN) are two of the macro trends of 6G candidate technologies, respectively. However, non-linearity of power amplifiers (PA) is a critical challenge for both sub-THz and NTN. Therefore, high power efficiency (PE) or low peak to average power ratio (PAPR) waveform design becomes one of the most significant 6G research topics. Meanwhile, high spectral efficiency (SE) and low out-of-band emission (OOBE) are still important key performance indicators (KPIs) for 6G waveform design. Single-carrier waveform discrete Fourier transform spreading orthogonal frequency division multiplexing (DFT-s-OFDM) has achieved many research interests due to its high PE, and it has been supported in 5G New Radio (NR) when uplink coverage is limited. So DFT-s-OFDM can be regarded as a candidate waveform for 6G. Many enhancement schemes based on DFT-s-OFDM have been proposed, including null cyclic prefix (NCP)/unique word (UW), frequency-domain spectral shaping (FDSS), and time-domain compression and expansion (TD-CE), etc. However, there is no unified framework to be compatible with all the enhancement schemes. This paper firstly provides a general description of the 6G candidate waveforms based on DFT-s-OFDM enhancement. Secondly, the more flexible TD-CE supporting methods for unified non-orthogonal waveform (uNOW) are proposed and discussed. Thirdly, a unified waveform framework based on DFT-s-OFDM structure is proposed. By designing the pre-processing and post-processing modules before and after DFT in the unified waveform framework, the three technical methods (NCP/UW, FDSS, and TD-CE) can be integrated to improve three KPIs of DFT-s-OFDM simultaneously with high flexibility. Then the implementation complexity of the 6G candidate waveforms are analyzed and compared. Performance of different DFT-s-OFDM enhancement schemes is investigated by link level simulation, which reveals that uNOW can achieve the best PAPR performance among all the 6G candidate waveforms. When considering PA back-off, uNOW can achieve 124% throughput gain compared to traditional DFT-s-OFDM.

Neuromorphic computing with a spiking neural network (SNN) is expected to provide a complement or alternative to deep learning in the future. The challenge is to develop optimal SNN models, algorithms, and engineering technologies for real use cases. As a potential use cases for neuromorphic computing, we have investigated a person monitoring and worker support with a video surveillance system, given its status as a proven deep neural network (DNN) use case. In the future, to increase the number of cameras in such a system, we will need a scalable approach that embeds only a few neuromorphic devices in a camera. Specifically, this will require a shallow SNN model that can be implemented in a few neuromorphic devices while providing a high recognition accuracy comparable to a DNN with the same configuration. A shallow SNN was built by converting ResNet, a proven DNN for image recognition, and a new configuration of the shallow SNN model was developed to improve its accuracy. The proposed shallow SNN model was evaluated with a few neuromorphic devices, and it achieved a recognition accuracy of more than 80% with about 1/130 less energy consumption than that of a GPU with the same configuration of DNN as that of SNN.

The acquisition of distant sound has always been a hot research topic. Since sound is caused by vibration, one of the best methods for measuring distant sound is to use a laser Doppler vibrometer (LDV). This laser has high directivity, that enables it to acquire sound from far away, which is of great practical use for disaster relief and other situations. However, due to the vibration characteristics of the irradiated object itself and the reflectivity of its surface (or other reasons), the acquired sound is often lacking frequency components in certain frequency bands and is mixed with obvious noise. Therefore, when using LDV to acquire distant speech, if we want to recognize the actual content of the speech, it is necessary to enhance the acquired speech signal in some way. Conventional speech enhancement methods are not generally applicable due to the various types of degradation in observed speech. Moreover, while several speech enhancement methods for LDV have been proposed, they are only effective when the irradiated object is known. In this paper, we present a speech enhancement method for LDV that can deal with unknown irradiated objects. The proposed method is composed of noise reduction, pitch detection, power spectrum envelope estimation, power spectrum reconstruction, and phase estimation. Experimental results demonstrate the effectiveness of our method for enhancing the acquired speech with unknown irradiated objects.

We study a new transistor-level side-channel leakage caused by charges trapped in between stacked transistors namely residual electric charges (RECs). Building leakage models is important in designing countermeasures against side-channel attacks (SCAs). The conventional work showed that even a transistor-level leakage is measurable with a local electromagnetic measurement. One example is the current-path leak [1], [2]: an attacker can distinguish the number of transistors in the current path activated during a signal transition. Addressing this issue, Sugawara et al. proposed to use a mirror circuit that has the same number of transistors on its possible current paths. We show that this countermeasure is insufficient by showing a new transistor-level leakage, caused by RECs, not covered in the previous work. RECs can carry the history of the gate's state over multiple clock cycles and changes the gate's electrical behavior. We experimentally verify that RECs cause exploitable side-channel leakage. We also propose a countermeasure against REC leaks and designed advanced encryption standard-128 (AES-128) circuits using IO-masked dual-rail read-only memory with a 180-nm complementary metal-oxide-semiconductor (CMOS) process. We compared the resilience of our AES-128 circuits against EMA attacks with and without our countermeasure and investigated an RECs' effect on physically unclonable functions (PUFs). We further extend RECs to physically unclonable function. We demonstrate that RECs affect the performance of arbiter and ring-oscillator PUFs through experiments using our custom chips fabricated with 180- and 40-nm CMOS processes*.

The hardness of the syndrome decoding problem (SDP) is the primary evidence for the security of code-based cryptosystems, which are one of the finalists in a project to standardize post-quantum cryptography conducted by the U.S. National Institute of Standards and Technology (NIST-PQC). Information set decoding (ISD) is a general term for algorithms that solve SDP efficiently. In this paper, we conducted a concrete analysis of the time complexity of the latest ISD algorithms under the limitation of memory using the syndrome decoding estimator proposed by Esser et al. As a result, we present that theoretically nonoptimal ISDs, such as May-Meurer-Thomae (MMT) and May-Ozerov, have lower time complexity than other ISDs in some actual SDP instances. Based on these facts, we further studied the possibility of multiple parallelization for these ISDs and proposed the first GPU algorithm for MMT, the multiparallel MMT algorithm. In the experiments, we show that the multiparallel MMT algorithm is faster than existing ISD algorithms. In addition, we report the first successful attempts to solve the 510-, 530-, 540- and 550-dimensional SDP instances in the Decoding Challenge contest using the multiparallel MMT.

Electromagnetic scattering in a coaxial cable having two flanges and concentric grooves is studied. The associated Weber-Orr transform is used to represent electromagnetic fields in an infinitely long cavity, and the mode-matching method is used to enforce boundary continuity. S-parameters obtained by our approach are compared with the reference solutions, and the characteristics are discussed when geometric parameters are varied. The results show that the proposed model provides cost effective and accurate solutions to the problem.

Multiple wireless communication systems are often operated together in the same area in such manufacturing sites as factories where wideband noise may be emitted from industrial equipment over channels for wireless communication systems. To perform highly reliable wireless communication in such environments, radio wave environments must be monitored that are specific to each manufacturing site to find channels and timing that enable stable communication. The authors studied technologies using machine learning to efficiently analyze a large amount of monitoring data, including signals whose spectrum shape is undefined, such as electromagnetic noise over a wideband. In this paper, we generated common supervised data for multiple sensors by conjointly clustering features after normalizing those calculated in each sensor to recognize the signal reception timing from identical sources and eliminate the complexity of supervised data management. We confirmed our method's effectiveness through signal models and actual data sampled by sensors that we developed.

In this paper, the author performed an electromagnetic field simulation of a typical bonding wire structure that connects a chip and a package, and evaluated the signal transmission characteristics (S-parameters). In addition, the inductance per unit length was extracted by comparing with the equivalent circuit of the distributed constant line. It turns out that the distributed constant line model is not sufficient because there are frequencies where chip-package resonance occurs. Below the resonance frequency, the conventional low-frequency approximation model was effective, and it was found that the inductance was about 1nH/mm.

We have investigated the electromotive force (EMF) of a composite sample consisting of a Π-type thermoelectric power generation structure with a pair of n- and p-type Si wafers and piezoelectric devices in order to collect electricity from vibration energy and thermal energy, simultaneously. The observed EMF was obtained by superimposing the oscillating EMF of vibration energy on the constant EMF of thermal energy. Therefore, we have improved the composite sample with diodes for rectifying the oscillating EMF. As a result, the full-wave rectification and the preservation of EMF amplitude were realized. From the frequency dependence, it was found that the dielectric loss of the piezoelectric device influences the amplitude and the time delay in the EMF.

Inter-channel correlation is one of the redundancy which need to be eliminated in video coding. In the latest video coding standard H.266/VVC, the DM (Direct Mode) and CCLM (Cross-component Linear Model) modes have been introduced to reduce the similarity between luminance and chroma. However, inter-channel correlation is still observed. In this paper, a new inter-channel prediction algorithm is proposed, which utilizes coloring principle to predict chroma pixels. From the coloring perspective, for most natural content video frames, the three components Y, U and V always demonstrate similar coloring pattern. Therefore, the U and V components can be predicted using the coloring pattern of the Y component. In the proposed algorithm, correlation coefficients are obtained in a lightweight way to describe the coloring relationship between current pixel and reference pixel in Y component, and used to predict chroma pixels. The optimal position for the reference samples is also designed. Base on the selected position of the reference samples, two new chroma prediction modes are defined. Experiment results show that, compared with VTM 12.1, the proposed algorithm has an average of -0.92% and -0.96% BD-rate improvement for U and V components, for All Intra (AI) configurations. At the same time, the increased encoding time and decoding time can be ignored.