A GSM900/DCS1800 dual-band AlGaAs/GaAs HBT (heterojunction bipolar transistor) MMIC (monolithic microwave integrated circuit) power amplifier has been developed. It includes power amplifiers for GSM900 and DCS1800, constant voltage bias circuits and a d. c. switch. In order to achieve high efficiency, the outside-base/center-via-hole layout is applied to the final-stage HBT of the MMIC amplifier. The layout can realize uniform output load impedance and thermal distribution of each HBT finger. The developed MMIC amplifier could provided output power of 34.5 dBm and power-added efficiency of 53.4% for GSM900, and output power of 32.0 dBm and power-added efficiency of 41.8% for DCS1800.

A fully on-chip current controlled open-drain output driver using a bandgap reference current generator was designed for high bandwidth DRAMs. It reduces the overhead of receiving a digital code from an external source for the compensation of the temperature and supply voltage variations. The correct value of the current control register is updated at the end of every auto refresh cycle. The operation at the data rate up to 0.8 Gb/s was verified by SPICE simulation using a 0.22 µm triple-well CMOS technology.

A high-frequency, low-noise silicon bipolar transistor that can be used in over-10 Gb/s optical communication systems and wireless communication systems has been developed. The silicon bipolar transistor was fabricated using self-aligned metal/IDP (SMI) technology, which produces a self-aligned base electrode of stacked layers of metal and in-situ doped poly-Si (IDP) by low-temperature selective tungsten CVD. It provides a low base resistance and high-cutoff frequency. The base resistance is reduced to half that of a transistor with a conventional poly-Si base electrode. By using the SMI technology and optimizing the depth of the emitter and the link base, we achieved the maximum oscillation frequency of 80 GHz, a minimum gate delay in an ECL of 11.6 ps, and the minimum noise figure of 0.34 dB at 2 GHz, which are the highest performances among those obtained from ion-implanted base Si bipolar transistors, and are comparable to those of SiGe base heterojunction bipolar transistors.

Internet communication is increasingly becoming an important element in daily life. Keeping this network safe from malicious elements is an urgent task for network management. To maintain the security level networks are generally, monitored for indications of usage with ill-intentions. Such indications are events which need to be collated, correlated and analyzed in real-time to be effective. However, on an average medium to large size network the number of such events are very large. This makes it practically impossible to analyze the information in real-time and provide the necessary security measures. In this paper, we propose a mechanism that keeps the number of events, to be analyzed, low thereby making it possible to provide ample security measures. We discuss a real-time Intrusion Detection System (IDS) for detecting network attacks. The system looks out for TCP ACK/RST packets, which are generally caused by network scans. The system can extract the tendency of network flows in real-time, based on the newly developed time-based clustering and Dynamic Access Tree creation techniques. The algorithm, implemented and deployed on a medium size backbone network using RMON (Remote MONitoring) technology, successfully detected 195 intrusion attempts during a one month period. The results of the pilot deployment are discussed. In this paper, the proposal, implementation and evaluation will be described.

The Matrix-Pencil (MP) method is applied to the estimation of the undesired radiation from the microstrip line discontinuities. The Q factors are obtained from the complex resonant frequencies estimated from FDTD transient field by using MP. The number of the damped oscillations is estimated by using MDL which is widely used as an information theoretic criterion for the model order estimation.

We have developed an active Q adaptor (AQA) to achieve integration of multiple management protocols and dynamic modification of managed object (MO) definitions. To achieve dynamic modification, we introduce a new MO framework, called dynamic-MO, which has the ability of modifying its own definition. A dynamic-MO is composed of meta-data and some behavior programs. Meta-data lists attributes of a dynamic-MO in a text format and a behavior program describes actions of a dynamic-MO in scripting language such as Java, Tcl, etc. In our AQA architecture, modules which manage individual components of a dynamic-MO communicate among themselves via an object request broker (ORB) in order to achieve system scalability with high performance. To realize the functionality of a dynamic-MO, we propose interfaces among these modules that are independent of dynamic-MO definitions and an update mechanism of behavior programs. We define the interfaces based on the common management information protocol (CMIP) operations to avoid re-defining the interfaces when dynamic-MO definitions are modified. Furthermore, to execute modified behavior programs without any negative influence on the workings of the other behavior programs, we employ a Java class-loader which has its own specific naming-space on a Java virtual machine (Java VM). With all of these features, our AQA is extremely promising for developing programmable network management systems for end-to-end management of heterogeneous telecommunication networks.

Mobile communication services have become popular due to the rapid popularization of cellular mobile telephones. In order to offer services to an increasing number of users and to upgrade services, the development of Third-Generation Mobile Telecommunication is required. Our proposed system utilizing W-CDMA enables high-speed variable data communications, uninterrupted hand-over between communication zones, doubling of subscriber capacity and reduction of operation costs. Various actions are being taken internationally toward the establishment of a global standard for the Third-Generation Mobile Telecommunication System, aiming at its practical application around AD 2000. The W-CDMA system has been adopted as the standard for Japan. We are developing experimental W-CDMA system equipment. For this development, many Field Programmable Gate Array (FPGA) devices and Digital Signal Processors (DSP) have been used to meet the changes of equipment specifications and system evaluation parameters. By developing customized Large-scale Integrated circuit (LSI) devices and high-speed DSP, a small-size portable phone and a compact visual phone have been realized. Also, high-density mounting of the signal processing parts has been done in the Base Transceiver Station (BTS). In the development of a Mobile Communication Controller Simulator (MCC-SIM), the developmental period has been shortened by using our ATM switching system (AD8700) and generic-use PBX (Pana EXA) in the proposed system. In this paper, the features of the W-CDMA system and the outline of the newly developed experimental equipment have been described.

We propose a new technique that is able to extract the small-signal equivalent-circuit elements of high electron mobility transistors (HEMTs) without causing any gate degradation. For the determination of extrinsic resistance values, unlike other conventional techniques, the proposed technique does not require an additional relationship for the resistances. For the extraction of extrinsic inductance values, the technique uses the R-estimate, which is known to be more robust relative to the measurement errors than the commonly used least-squares regression. Additionally, we suggest an improved cold HEMT model that seems to be more general than conventional cold HEMT models. With the use of the improved cold HEMT model, the proposed technique extracts the extrinsic resistance and inductance values.

This paper describes a novel layout optimization technique using electromagnetic (EM) simulation. Simple equivalent circuits fitted to EM simulation results are employed in this method, to present a modification guide for a layout pattern. Fitting errors are also investigated with some layout patterns in order to clarify the applicable range of the method, because the errors restrict the range. The method has been successfully adopted to an X-band low noise MMIC amplifier (LNA). The layout pattern of the amplifier was optimized in only two days and the amplifier has achieved target performances--a 35 dB gain and a 1.7 dB noise figure--in one development cycle. The effective chip area has been miniaturized to 4.8 mm2. The area could be smaller than 70% in comparison with a conventional layout MMIC.

A procedure for radar target discrimination is presented in this paper. The scheme includes an enhancement of late-time noisy scattering data based on a proposed signal processing algorithm and a decision procedure using previously known resonance annihilation filters. The signal processing stage is specifically adapted to scattering signals and makes use of the results of the singularity expansion method. It is based on a signal reconstruction using the SVD of a data matrix with a suitable choice of the number of singular vectors employed. To justify the inclusion of this stage, this procedure is shown to maintain the signal characteristics necessary to identify the scattered response. Simulation results clearly reveal a significant improvement due to the inclusion of the proposed stage. This improvement becomes especially important when the noise level is high or the targets to be discriminated (five regular polygonal loops) have a similar geometry.

This letter is concerned with a new algorithm which can be used to design a time-domain equalizer (TEQ) for xDSL systems employing the discrete multitone (DMT) modulation. The proposed algorithm, derived by neglecting the terms which do not affect the performance of a DMT system in ARMA modeling, is shown to have a good performance compared with the previous TEQ algorithms even with a significantly lower computational complexity. In addition, the proposed algorithm does not require the channel impulse response or training sequence, since all processing is made only with the received data.

In this paper, a method of Transmission Power Control (TPC) for Orthogonal Frequency Division Multiplexing Direct Sequence Code Division Multiple Access (OFDM-DS-CDMA), in order to compensate for power attenuation at each subcarrier, is proposed. Instead of assigning same power levels for all-subcarriers, different transmission power levels are assigned to different subcarriers, according to the attenuation of the subcarriers. System performance, in terms of Bit Error Rate (BER), has been evaluated by Monte Carlo simulation. The simulation results presented significant improvement, the proposed system performed much better than the system without TPC. It is shown that the Each Carrier TPC performs better than All Carriers TPC, which all carriers are controlled uniformly, hence Each Carrier TPC is more suitable for OFDM-DS-CDMA system.

Silicon-based monolithic microwave integrated circuits (MMICs) present an interesting option for low-cost consumer wireless systems. SiGe/Si heterojunction bipolar transistors (HBTs) are a major driving force behind Si-based MMICs, because they offer excellent microwave performance without aggressive lateral scaling. This article reviews opportunities for receiver frontend components (low-noise amplifiers and mixers) using SiGe HBTs.

For backup of failed VPs (Virtual Paths) in ATM (Asynchronous Transfer Mode) networks, many self-healing algorithms have already been proposed. However, since the existing algorithms recover each failed VP with a single backup VP, a problem arises in that those algorithms cannot necessarily provide a failed VP having a higher recovery priority with a larger recovery ratio, which is the ratio of the bandwidth of a backup VP to that of a failed VP. For a solution to the problem, this paper proposes a new self-healing algorithm which recovers each failed VP with one or more backup VPs. We also evaluate its availability by comparing with an existing algorithm through simulations.

This paper proposes an implementation of the Telecommunications Information Networking Architecture (TINA) connection management system, based on our involvement of The TINA Trial (TTT). The system is used for managing ATM networks, which consist of network elements with SNMP interfaces. It provides setup, configuration, and release of ATM connection with a GUI-based network design tool that generates network resource data used for deploying TINA software components. This paper reports on a method of implementing TINA components over a Distributed Processing Environment (DPE) and an effective way to manage computational objects with multiple interfaces by using the Trading Service.

A 100 W, low distortion AlGaAs/GaAs heterostructure FET has been developed for CDMA cellular base stations. This FET employs the longest gate finger ever reported of 800 µm to shrink the chip size. The size of the chip and the package are miniaturized to 1.242.6 mm2 and 17.4 24.0 mm2, respectively. The developed FET exhibits 100 W (50 dBm) saturation output power, and 11.5 dB power gain at 1 dB gain compression at 2.1 GHz. The third-order intermodulation distortion and the power-added efficiency under the two-tone test condition (Δf=1 MHz) are -35 dBc and 24%, respectively at 42 dBm output power, that is 8 dB back off from the saturation power.

The constant modulus algorithm (CMA) of the adaptive array has been developed for suppressing the co-channel interference and the intersymbol interference in mobile communications. In this paper a novel CMA for the hybrid of the adaptive array and equalizer (HAE) is proposed to combat the problems of insufficient degrees of freedom and mainbeam multipath interferers. The HAE with CMA utilizes the constant modulus property for the output signal of the HAE to adjust the weight vectors of the array and equalizer simultaneously. The co-channel interferers can be canceled by the array and the multipath interferers can be removed by the array or the equalizer following the array in the HAE. Therefore, the array in the HAE with CMA may need less number of elements than that required by the CMA array which cancels both the co-channel interferers and multipath interferers. Besides, the presence of the mainbeam multipath interferers, which may seriously degrade the performance of the CMA array, has much less effect on the HAE with CMA since it can be suppressed by the equalizer instead of the array. Simulation results are presented to demonstrate the merits of the CMA for the HAE.

Newer off-chip DRAM families, including Synchronous DRAMs (SDRAMs) and RAMBUS DRAMs (RDRAMs), are becoming standard choices for the design of high-performance systems. Although previous work in High-Level Synthesis (HLS) has addressed exploiting features of page-mode DRAMs, techniques do not exist for exploiting the two key features of these newer DRAM families that boost memory performance and help overcome bandwidth limitations: (1) burst mode access, and (2) interleaved access through multiple banks. We address pre-synthesis optimizations on the input behavior that extract and exploit the burst mode and multiple bank interleaved access modes of these newer DRAM families, so that these features can be exploited fully during the HLS trajectory. Our experiments, run on a suite of memory-intensive benchmarks using a contemporary SDRAM library, demonstrate significant performance improvements of up to 62.5% over the naive approach, and improvements of up to 16.7% over the previous approach that considered only page-mode or extended-data-out (EDO) DRAMS.

Simple approximate formulas are obtained for the mutual impedance and admittance by using a product of radiation patterns of antennas. The formulas come from a stationary expression of the reaction integral between two antennas where far-field approximations are employed. The theory deals with antennas in free space as well as under the presence of a wedge. Two applications are given for microstrip antennas with experimental verifications.

As telecommunications companies face the rigors of competition, they soon find that their operational support systems play a critical role in providing new services faster, at lower cost and with better quality than their competitors. At TeleManagement Forum, the model for the successful service provider is 'the smooth operator' - a company whose processes and systems fully support its people to provide the best services possible at the lowest cost. Learning the importance of becoming a 'smooth operator' is hard, particularly as it requires giving up the old way of doing things - moving from an internal development environment to one that can take full advantage of 'off-the-shelf' software. The reasons for this shift include a shortage of resources, shortage of time, and the need to do business as part of a greater (and growing) global supply chain. Getting to 'smooth operator' status can be made easier with help from organizations like the TeleManagement Forum. In this paper, a twelve-step method is outlined to give pointers to service providers and their suppliers on how to make the journey successfully.