The existing literature focuses on the applications of fast filter bank due to its excellent frequency responses with low complexity. However, the topic is not addressed related to the general transfer function expressions of the corresponding subfilters for a specific channel. To do this, in this paper, general closed-form transfer function expressions for fast filter bank are derived. Firstly, the cascaded structure of fast filter bank is modelled by a binary tree, with which the index of the subfilter at each stage within the channel can be determined. Then the transfer functions for the two outputs of a subfilter are expressed in a unified form. Finally, the general closed-form transfer functions for the channel and its corresponding subfilters are obtained by variables replacement if the prototype lowpass filters for the stages are given. Analytical results and simulations verify the general expressions. With such closed-form expressions lend themselves easily to analysis and direct computation of the transfer functions and the frequency responses without the structure graph.

The ionospheric clutter in High Frequency Surface Wave Radar (HFSWR) is the reflection of electromagnetic waves from the ionosphere back to the receiver, which should be suppressed as much as possible for the primary purpose of target detection in HFSWR. However, ionospheric clutter contains vast quantities of ionospheric state information. By studying ionospheric clutter, some of the relevant ionospheric parameters can be inferred, especially during the period of typhoons, when the ionospheric state changes drastically affected by typhoon-excited gravity waves, and utilizing the time-frequency characteristics of ionospheric clutter at typhoon time, information such as the trend of electron concentration changes in the ionosphere and the direction of the typhoon can be obtained. The results of the processing of the radar data showed the effectiveness of this method.

The low-hit-zone (LHZ) frequency hopping sequence (FHS) sets are widely applicable in quasi-synchronous frequency hopping multiple-access (QS-FHMA) systems. In order to reduce mutual interference (MI) in the zone around the signal origin between different users, we recommend the LHZ FHS set instead of the conventional FHS set. In this letter, we propose a design of LHZ FHS sets via interleaving techniques. The obtained sequences can be confirmed that they are near-optimal in relation to the Peng-Fan-Lee bound.

Mission-critical monitoring services, such as finding criminals with a monitoring camera, require rapid detection of newly updated data, where suppressing delay is desirable. Taking this direction, this paper proposes a network design scheme to minimize this delay for monitoring services that consist of Internet-of-Things (IoT) devices located at terminal endpoints (TEs), databases (DB), and applications (APLs). The proposed scheme determines the allocation of DB and APLs and the selection of the server to which TE belongs. DB and APL are allocated on an optimal server from multiple servers in the network. We formulate the proposed network design scheme as an integer linear programming problem. The delay reduction effect of the proposed scheme is evaluated under two network topologies and a monitoring camera system network. In the two network topologies, the delays of the proposed scheme are 78 and 80 percent, compared to that of the conventional scheme. In the monitoring camera system network, the delay of the proposed scheme is 77 percent compared to that of the conventional scheme. These results indicate that the proposed scheme reduces the delay compared to the conventional scheme where APLs are located near TEs. The computation time of the proposed scheme is acceptable for the design phase before the service is launched. The proposed scheme can contribute to a network design that detects newly added objects quickly in the monitoring services.

The performance of a fully wireless-power-transfer (WPT) node network, in which each node transfers (and receives) energy through a wireless channel when it has sufficient (and insufficient) energy in its battery, was theoretically analyzed. The lost job ratio (LJR), namely, is the ratio of (i) the amount of jobs that cannot be done due to battery of a node running out to (ii) the amount of jobs that should be done, is used as a performance metric. It describes the effect of the battery of each node running out and how much additional energy is needed. Although it is known that WPT can reduce the probability of the battery running out among a few nodes within a small area, the performance of a fully WPT network has not been clarified. By using stochastic geometry and first-passage-time analysis for a diffusion process, the expected LJR was theoretically derived. Numerical examples demonstrate that the key parameters determining the performance of the network are node density, threshold switching of statuses between “transferring energy” and “receiving energy,” and the parameters of power conversion. They also demonstrate the followings: (1) The mean energy stored in the node battery decreases in the networks because of the loss caused by WPT, and a fully WPT network cannot decrease the probability of the battery running out under the current WPT efficiency. (2) When the saturation value of power conversion increases, a fully WPT network can decrease the probability of the battery running out although the mean energy stored in the node battery still decreases in the networks. This result is explained by the fact that the variance of stored energy in each node battery becomes smaller due to transfer of energy from nodes of sufficient energy to nodes of insufficient energy.

This study proposes a new asynchronous Multi-Rate Multiple-Access Differential Chaos Shift Keying (MRMA-DCSK) scheme, ensuring significant data rates for all users. This scheme assigns a unique chaos sequence with a different length to each user. During the first data transmission period, each user transmits the chaos sequence as the reference signal, followed by multiple data bits by sharing the same reference signal in subsequent periods. The proposed scheme affects the bit-error-rate (BER) performance with the number of users, data rate related parameters (L), and length of chaos signals. The simulation results are verified by the derived analysis and show that the proposed scheme achieves higher data rates (from 1/2 to L/L+1) than a conventional scheme while enhancing bit-error-rate (BER) performance.

In the current heterogeneous wireless communication system, the sharp rise in energy consumption and the emergence of new service types pose great challenges to nowadays radio access network selection algorithms which do not take care of these new trends. So the proposed energy efficiency based multi-service heterogeneous access network selection algorithm-ESRS (Energy Saving Radio access network Selection) is intended to reduce the energy consumption caused by the traffic in the mobile network system composed of Base Stations (BSs) and Access Points (APs). This algorithm models the access network selection problem as a Multiple-Attribute Decision-Making (MADM) problem. To solve this problem, lots of methods are combined, including analytic Hierarchy Process (AHP), weighted grey relational analysis (GRA), entropy theory, simple additive weight (SAW), and utility function theory. There are two main steps in this algorithm. At first, the proposed algorithm gets the result of the user QoS of each network by dealing with the related QoS parameters, in which entropy theory and AHP are used to determine the QoS comprehensive weight, and the SAW is used to get each network's QoS. In addition to user QoS, parameters including user throughput, energy consumption utility and cost utility are also calculated in this step. In the second step, the fuzzy theory is used to define the weight of decision attributes, and weighted grey relational analysis (GRA) is used to calculate the network score, which determines the final choice. Because the fuzzy weight has a preference for the low energy consumption, the energy consumption of the traffic will be saved by choosing the network with the least energy consumption as much as possible. The simulation parts compared the performance of ESRS, ABE and MSNS algorithms. The numerical results show that ESRS algorithm can select the appropriate network based on the service demands and network parameters. Besides, it can effectively reduce the system energy consumption and overall cost while still maintaining a high overall QoS value and a high system throughput, when compared with the other two algorithms.

This paper proposes a virtual network function (VNF) placement model considering both availability and probabilistic protection for the service delay to minimize the service deployment cost. Both availability and service delay are key requirements of services; a service provider handles the VNF placement problem with the goal of minimizing the service deployment cost while meeting these and other requirements. The previous works do not consider the delay of each route which the service can take when considering both availability and delay in the VNF placement problem; only the maximum delay was considered. We introduce probabilistic protection for service delay to minimize the service deployment cost with availability. The proposed model considers that the probability that the service delay, which consists of networking delay between hosts and processing delay in each VNF, exceeds its threshold is constrained within a given value; it also considers that the availability is constrained within a given value. We develop a two-stage heuristic algorithm to solve the VNF placement problem; it decides primary VNF placement by solving mixed-integer second-order cone programming in the first stage and backup VNF placement in the second stage. We observe that the proposed model reduces the service deployment cost compared to a baseline that considers the maximum delay by up to 12%, and that it obtains a feasible solution while the baseline does not in some examined situations.

In this article, a new Beamforming Network (BFN) realized in Broadside Coupled Stripline (BCS) is proposed to feed 1×4 and 2×2 arrays antenna at 28 GHZ-Band. The new BFN is composed only of couplers and phase shifters. It doesn't require any crossover compared to the conventional Butler Matrix (BM) which requires two crossovers. The tight coupling and low loss characteristics of the BCS allow a design of a compact and wideband BFN. The new BFN produces the phase differences of (±90°) and (±45°, ±135°) respectively in x- and y-directions. Its integration with a 1×4 linear array antenna reduces the array area by 70% with an improvement of the gain performance compared with the conventional array. The integration with a 2×2 array allows the realization of a full 2-D beam scanning. The proposed concept has been verified experimentally by measuring the fabricated prototypes of the BFN, the 1-D and 2-D patch arrays antennas. The measured 11.5 dBi and 11.3 dBi maximum gains are realized in θ0 = 14° and (θ0, φ0) = (45°,345°) directions respectively for the 1-D and 2-D patch arrays. The physical area of the fabricated BFN is only (0.37λ0×0.3λ0×0.08λ0), while the 1-D array and 2-D array antennas areas without feeding transmission lines are respectively (0.5λ0×2.15λ0×0.08λ0) and (0.9λ0×0.8λ0×0.08λ0).

Today's electronic devices must meet many requirements, such as those related to performance, limits to the radiated electromagnetic field, size, etc. For such a design, the requirement is to have a solution that simultaneously meets multiple objectives that sometimes include conflicting requirements. In addition, it is also necessary to consider uncertain parameters. This paper proposes a new combination of statistical analysis using the Polynomial Chaos (PC) method for dealing with the random and multi-objective satisfactory design using the Preference Set-based Design (PSD) method. The application in this paper is an Electromagnetic Interference (EMI) filter for a practical case, which includes plural element parameters and uncertain parameters, which are resistors at the source and load, and the performances of the attenuation characteristics. The PC method generates simulation data with high enough accuracy and good computational efficiency, and these data are used as initial data for the meta-modeling of the PSD method. The design parameters of the EMI filter, which satisfy required performances, are obtained in a range by the PSD method. The authors demonstrate the validity of the proposed method. The results show that applying a multi-objective design method using PSD with a statistical method using PC to handle the uncertain problem can be applied to electromagnetic designs to reduce the time and cost of product development.

This paper analyzes the typical functions of digital control circuit and its function modules, and develops a set of digital control circuit equipment based on Advanced RISC Machines (ARM) with typical function modules, including principle design, interference injection trace design, function design, and study the failure mode and threshold of typical function modules. Based on continuous wave (CW) and pulse wave, the direct power injection (DPI) method is used to test the conduction immunity of the digital control circuit, and the failure mode and sensitivity threshold of the digital control circuit are quantitatively obtained. This method can provide experimental verification for the immunity ability of the digital control circuit to different electromagnetic interference.

In the cellular system, the Worst Case User (WCU), whose distances to three nearest BSs are the similar, usually achieves the lowest performance. Improving user performance, especially the WCU, is a big problem for both network designers and operators. This paper works on the WCU in terms of coverage probability analysis by the stochastic geometry tool and data rate optimization with the transmission power constraint by the reinforcement learning technique under the Stretched Pathloss Model (SPLM). In analysis, only fast fading from the WCU to the serving Base Stations (BSs) is taken into the analysis to derive the lower bound coverage probability. Furthermore, the paper assumes that the Coordinated Multi-Point (CoMP) technique is only employed for the WCU to enhance its downlink signal and avoid the explosion of Intercell Interference (ICI). Through the analysis and simulation, the paper states that to improve the WCU performance under bad wireless environments, an increase in transmission power can be a possible solution. However, in good environments, the deployment of advanced techniques such as Joint Transmission (JT), Joint Scheduling (JS), and reinforcement learning is an suitable solution.

In recent years, physical layer security (PLS), which utilizes the inherent randomness of wireless signals to perform encryption at the physical layer, has attracted attention. We propose chaos modulation as a PLS technique. In addition, a method for encryption using a special encoder of polar codes has been proposed (PLS-polar), in which PLS can be easily achieved by encrypting the frozen bits of a polar code. Previously, we proposed a chaos-modulated polar code transmission method that can achieve high-quality and improved-security transmission using frozen bit encryption in polar codes. However, in principle, chaos modulation requires maximum likelihood sequence estimation (MLSE) for demodulation, and a large number of candidates for MLSE causes characteristic degradation in the low signal-to-noise ratio region in chaos polar transmission. To address this problem, in this study, we propose a versatile frozen bit method for polar codes, in which the frozen bits are also used to reduce the number of MLSE candidates for chaos demodulation. The numerical results show that the proposed method shows a performance improvement by 1.7dB at a block error rate of 10-3 with a code length of 512 and a code rate of 0.25 compared with that of conventional methods. We also show that the complexity of demodulation can be reduced to 1/16 of that of the conventional method without degrading computational security. Furthermore, we clarified the effective region of the proposed method when the code length and code rate were varied.

To cope with ever growing mobile data traffic, we recently proposed a concept of cellular ultra-dense radio access network (RAN). In the cellular ultra-dense RAN, a number of distributed antennas are deployed in the base station (BS) coverage area (cell) and user-clusters are formed to perform small-scale distributed multiuser multi-input multi-output (MU-MIMO) transmission and reception in each user-cluster in parallel using the same frequency resource. We also proposed a decentralized interference coordination (IC) framework to effectively mitigate both intra-cell and inter-cell interferences caused in the cellular ultra-dense RAN. The inter-cell IC adopted in this framework is the fractional frequency reuse (FFR), realized by applying the channel segregation (CS) algorithm, and is called CS-FFR in this paper. CS-FFR divides the available bandwidth into several sub-bands and allocates multiple sub-bands to different cells. In this paper, focusing on the optimization of the CS-FFR, we find by computer simulation the optimum bandwidth division number and the sub-band allocation ratio to maximize the link capacity. We also discuss the convergence speed of CS-FFR in a cellular ultra-dense RAN.

This paper proposes low complexity resource allocation in frequency domain non-orthogonal multiple access where many devices access with a base station. The number of the devices is assumed to be more than that of the resource for network capacity enhancement, which is demanded in massive machine type communications (mMTC). This paper proposes two types of resource allocation techniques, all of which are based on the MIN-MAX approach. One of them seeks for nicer resource allocation with only channel gains. The other technique applies the message passing algorithm (MPA) for better resource allocation. The proposed resource allocation techniques are evaluated by computer simulation in frequency domain non-orthogonal multiple access. The proposed technique with the MPA achieves the best bit error rate (BER) performance in the proposed techniques. However, the computational complexity of the proposed techniques with channel gains is much smaller than that of the proposed technique with the MPA, whereas the BER performance of the proposed techniques with channel gains is only about 0.1dB inferior to that with the MPA in the multiple access with the overloading ratio of 1.5 at the BER of 10-4. They attain the gain of about 10dB at the BER of 10-4 in the multiple access with the overloading ration of 2.0. Their complexity is 10-16 as small as the conventional technique.

Hybrid automatic repeat request (HARQ) is an essential technology that efficiently reduces the transmission error rate. However, for ultra-reliable low latency communications (URLLC) in the 5th generation mobile communication systems and beyond, the increase in latency due to retransmission must be minimized in HARQ. In this paper, we propose a highly-efficient low-latency HARQ method built on non-orthogonal multiple access (NOMA) for URLLC while minimizing the performance loss for coexisting services (use cases) such as enhanced mobile broadband (eMBB). The proposed method can be seen as an extension of the conventional link-level non-orthogonal HARQ to the system-level protocol. This mitigates the problems of the conventional link-level non-orthogonal HARQ, which are decoding error under poor channel conditions and an increase in transmission delay due to restrictions in retransmission timing. In the proposed method, delay-sensitive URLLC packets are preferentially multiplexed with best-effort eMBB packets in the same channel using superposition coding to reduce the transmission latency of the URLLC packet while alleviating the throughput loss in eMBB. This is achieved using a weighted channel-aware resource allocator (scheduler). The inter-packet interference multiplexed in the same channel is removed using a successive interference canceller (SIC) at the receiver. Furthermore, the transmission rates for the initial transmission and retransmission are controlled in an appropriate manner for each service in order to deal with decoding errors caused by error in transmission rate control originating from a time varying channel. We show that the proposed method significantly improves the overall performance of a system that simultaneously provides eMBB and URLLC services.

Recent years have seen a decline in the art of analog IC design even though analog interface and analog signal processing remain just as essential as ever. While there are many contributing factors, four specific pressures which contribute the most to the loss of creativity and innovation within analog practice are examined: process evolution, risk aversion, digitally assisted analog, and corporate culture. Despite the potency of these forces, none are found to be insurmountable obstacles to reinvigorating the industry. A more creative future is within our reach.

In this paper, we propose a hybrid crystal oscillator which achieves both quick startup and low steady-state power consumption. At startup, a large negative resistance is realized by configuring a Pierce oscillating circuit with a multi-stage inverter amplifier, resulting in high-speed startup. During steady-state oscillation, the oscillator is reconfigured as a class-C complementary Colpitts circuit for low power consumption and low phase noise. Prototype chips were fabricated in 65nm CMOS process technology. With Pierce-type configuration, the measured startup time and startup energy of the oscillator are reduced to 1/11 and 1/5, respectively, compared with the one without Pierce-type configuration. The power consumption during steady oscillation is 30 µW.

This paper presents a divide-by-9 injection-locked frequency divider (ILFD). It can lock onto about 6-GHz input with a locking range of 3.23GHz (58%). The basic concept of the ILFD is based on employing self-gated multiple inputs into the multiple-stage ring oscillator. A wide lock range is also realized by adapting harmonic-control circuits, which can boost specific harmonics generated by mixing. The ILFD was fabricated using a 55-nm deeply depleted channel (DDC) CMOS process. It occupies an area of 0.0210mm2, and consumes a power of 14.4mW.

A power-scalable sub-sampling phase-locked loop (SSPLL) is proposed for realizing dual-mode operation; high-performance mode with good phase noise and power-saving mode with moderate phase noise. It is the most efficient way to reduce power consumption by lowering the supply voltage. However, there are several issues with the low-supply millimeter-wave (mmW) SSPLL. This work discusses some techniques, such as a back-gate forward body bias (FBB) technique, in addition to employing a CMOS deeply depleted channel process (DDC).